Some of the conditions in need_this_block have very straight
forward motivation. Separate those out and document them.
Signed-off-by: NeilBrown <neilb@suse.de>
fetch_block() has a very large and hard to read 'if' condition.
Separate it into its own function so that it can be
made more readable.
Signed-off-by: NeilBrown <neilb@suse.de>
67f455486d introduced a call to
md_wakeup_thread() when adding to the delayed_list. However the md
thread is woken up unconditionally just below.
Remove the unnecessary wakeup call.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a non-page-aligned write is destined for a device which
is missing/faulty, we can deadlock.
As the target device is missing, a read-modify-write cycle
is not possible.
As the write is not for a full-page, a recontruct-write cycle
is not possible.
This should be handled by logic in fetch_block() which notices
there is a non-R5_OVERWRITE write to a missing device, and so
loads all blocks.
However since commit 67f455486d, that code requires
STRIPE_PREREAD_ACTIVE before it will active, and those circumstances
never set STRIPE_PREREAD_ACTIVE.
So: in handle_stripe_dirtying, if neither rmw or rcw was possible,
set STRIPE_DELAYED, which will cause STRIPE_PREREAD_ACTIVE be set
after a suitable delay.
Fixes: 67f455486d
Cc: stable@vger.kernel.org (v3.16+)
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
It is critical that fetch_block() and handle_stripe_dirtying()
are consistent in their analysis of what needs to be loaded.
Otherwise raid5 can wait forever for a block that won't be loaded.
Currently when writing to a RAID5 that is resyncing, to a location
beyond the resync offset, handle_stripe_dirtying chooses a
reconstruct-write cycle, but fetch_block() assumes a
read-modify-write, and a lockup can happen.
So treat that case just like RAID6, just as we do in
handle_stripe_dirtying. RAID6 always does reconstruct-write.
This bug was introduced when the behaviour of handle_stripe_dirtying
was changed in 3.7, so the patch is suitable for any kernel since,
though it will need careful merging for some versions.
Cc: stable@vger.kernel.org (v3.7+)
Fixes: a7854487cd
Reported-by: Henry Cai <henryplusplus@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
raid5: fix init_stripe() inconsistencies
1) remove_hash() is not necessary. We will only be called right after
get_free_stripe(). There we have already a call to remove_hash().
2) Tracing prints out the sector of the freed stripe and not the sector
that we want to initialize.
Signed-off-by: NeilBrown <neilb@suse.de>
It has come to my attention (thanks Martin) that 'discard_zeroes_data'
is only a hint. Some devices in some cases don't do what it
says on the label.
The use of DISCARD in RAID5 depends on reads from discarded regions
being predictably zero. If a write to a previously discarded region
performs a read-modify-write cycle it assumes that the parity block
was consistent with the data blocks. If all were zero, this would
be the case. If some are and some aren't this would not be the case.
This could lead to data corruption after a device failure when
data needs to be reconstructed from the parity.
As we cannot trust 'discard_zeroes_data', ignore it by default
and so disallow DISCARD on all raid4/5/6 arrays.
As many devices are trustworthy, and as there are benefits to using
DISCARD, add a module parameter to over-ride this caution and cause
DISCARD to work if discard_zeroes_data is set.
If a site want to enable DISCARD on some arrays but not on others they
should select DISCARD support at the filesystem level, and set the
raid456 module parameter.
raid456.devices_handle_discard_safely=Y
As this is a data-safety issue, I believe this patch is suitable for
-stable.
DISCARD support for RAID456 was added in 3.7
Cc: Shaohua Li <shli@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Heinz Mauelshagen <heinzm@redhat.com>
Cc: stable@vger.kernel.org (3.7+)
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Fixes: 620125f2bf
Signed-off-by: NeilBrown <neilb@suse.de>
During recovery of a double-degraded RAID6 it is possible for
some blocks not to be recovered properly, leading to corruption.
If a write happens to one block in a stripe that would be written to a
missing device, and at the same time that stripe is recovering data
to the other missing device, then that recovered data may not be written.
This patch skips, in the double-degraded case, an optimisation that is
only safe for single-degraded arrays.
Bug was introduced in 2.6.32 and fix is suitable for any kernel since
then. In an older kernel with separate handle_stripe5() and
handle_stripe6() functions the patch must change handle_stripe6().
Cc: stable@vger.kernel.org (2.6.32+)
Fixes: 6c0069c0ae
Cc: Yuri Tikhonov <yur@emcraft.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Reported-by: "Manibalan P" <pmanibalan@amiindia.co.in>
Tested-by: "Manibalan P" <pmanibalan@amiindia.co.in>
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1090423
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
If a stripe in a raid6 array received a write to each data block while
the array is degraded, and if any of these writes to a missing device
are not page-aligned, then a live-lock happens.
In this case the P and Q blocks need to be read so that the part of
the missing block which is *not* being updated by the write can be
constructed. Due to a logic error, these blocks are not loaded, so
the update cannot proceed and the stripe is 'handled' repeatedly in an
infinite loop.
This bug is unlikely as most writes are page aligned. However as it
can lead to a livelock it is suitable for -stable. It was introduced
in 3.16.
Cc: stable@vger.kernel.org (v3.16)
Fixed: 67f455486d
Signed-off-by: NeilBrown <neilb@suse.de>
Mostly performance improvements with a few corner-case bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=MaM/
-----END PGP SIGNATURE-----
Merge tag 'md/3.16' of git://neil.brown.name/md
Pull md updates from Neil Brown:
"Assorted md fixes for 3.16
Mostly performance improvements with a few corner-case bug fixes"
* tag 'md/3.16' of git://neil.brown.name/md:
raid5: speedup sync_request processing
md/raid5: deadlock between retry_aligned_read with barrier io
raid5: add an option to avoid copy data from bio to stripe cache
md/bitmap: remove confusing code from filemap_get_page.
raid5: avoid release list until last reference of the stripe
md: md_clear_badblocks should return an error code on failure.
md/raid56: Don't perform reads to support writes until stripe is ready.
md: refuse to change shape of array if it is active but read-only
The raid5 sync_request() processing calls handle_stripe() within the context of
the resync-thread. The resync-thread issues the first set of read requests
and this adds execution latency and slows down the scheduling of the next
sync_request().
The current rebuild/resync speed of raid5 is not much faster than what
rotational HDDs can sustain.
Testing the following patch on a 6-drive array, I can increase the rebuild
speed from 100 MB/s to 175 MB/s.
The sync_request() now just sets STRIPE_HANDLE and releases the stripe. This
creates some more parallelism between the resync-thread and raid5 kernel daemon.
Signed-off-by: Eivind Sarto <esarto@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A chunk aligned read increases counter active_aligned_reads and
decreases it after sub-device handle it successfully. But when a read
error occurs, the read redispatched by raid5d, and the
active_aligned_reads will not be decreased until we can grab a stripe
head in retry_aligned_read. Now suppose, a barrier io comes, set
conf->quiesce to 2, and wait until both active_stripes and
active_aligned_reads are zero. The retried chunk aligned read gets
stuck at get_active_stripe waiting until conf->quiesce becomes 0.
Retry_aligned_read and barrier io are waiting each other now.
One possible solution is that we ignore conf->quiesce, let the retried
aligned read finish. I reproduced this deadlock and test this patch on
centos6.0
Signed-off-by: NeilBrown <neilb@suse.de>
The stripe cache has two goals:
1. cache data, so next time if data can be found in stripe cache, disk access
can be avoided.
2. stable data. data is copied from bio to stripe cache and calculated parity.
data written to disk is from stripe cache, so if upper layer changes bio data,
data written to disk isn't impacted.
In my environment, I can guarantee 2 will not happen. And BDI_CAP_STABLE_WRITES
can guarantee 2 too. For 1, it's not common too. block plug mechanism will
dispatch a bunch of sequentail small requests together. And since I'm using
SSD, I'm using small chunk size. It's rare case stripe cache is really useful.
So I'd like to avoid the copy from bio to stripe cache and it's very helpful
for performance. In my 1M randwrite tests, avoid the copy can increase the
performance more than 30%.
Of course, this shouldn't be enabled by default. It's reported enabling
BDI_CAP_STABLE_WRITES can harm some workloads before, so I added an option to
control it.
Neilb:
changed BUG_ON to WARN_ON
Removed some assignments from raid5_build_block which are now not needed.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The (lockless) release_list reduces lock contention, but there is excessive
queueing and dequeuing of stripes on this list. A stripe will currently be
queued on the release_list with a stripe reference count > 1. This can cause
the raid5 kernel thread(s) to dequeue the stripe and decrement the refcount
without doing any other useful processing of the stripe. The are two cases
when the stripe can be put on the release_list multiple times before it is
actually handled by the kernel thread(s).
1) make_request() activates the stripe processing in 4k increments. When a
write request is large enough to span multiple chunks of a stripe_head, the
first 4k chunk adds the stripe to the plug list. The next 4k chunk that is
processed for the same stripe puts the stripe on the release_list with a
refcount=2. This can cause the kernel thread to process and decrement the
stripe before the stripe us unplugged, which again will put it back on the
release_list.
2) Whenever IO is scheduled on a stripe (pre-read and/or write), the stripe
refcount is set to the number of active IO (for each chunk). The stripe is
released as each IO complete, and can be queued and dequeued multiple times
on the release_list, until its refcount finally reached zero.
This simple patch will ensure a stripe is only queued on the release_list when
its refcount=1 and is ready to be handled by the kernel thread(s). I added some
instrumentation to raid5 and counted the number of times striped were queued on
the release_list for a variety of write IO sizes. Without this patch the number
of times stripes got queued on the release_list was 100-500% higher than with
the patch. The excess queuing will increase with the IO size. The patch also
improved throughput by 5-10%.
Signed-off-by: Eivind Sarto <esarto@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If it is found that we need to pre-read some blocks before a write
can succeed, we normally set STRIPE_DELAYED and don't actually perform
the read until STRIPE_PREREAD_ACTIVE subsequently gets set.
However for a degraded RAID6 we currently perform the reads as soon
as we see that a write is pending. This significantly hurts
throughput.
So:
- when handle_stripe_dirtying find a block that it wants on a device
that is failed, set STRIPE_DELAY, instead of doing nothing, and
- when fetch_block detects that a read might be required to satisfy a
write, only perform the read if STRIPE_PREREAD_ACTIVE is set,
and if we would actually need to read something to complete the write.
This also helps RAID5, though less often as RAID5 supports a
read-modify-write cycle. For RAID5 the read is performed too early
only if the write is not a full 4K aligned write (i.e. no an
R5_OVERWRITE).
Also clean up a couple of horrible bits of formatting.
Reported-by: Patrik Horník <patrik@dsl.sk>
Signed-off-by: NeilBrown <neilb@suse.de>
I hit another BUG_ON with e240c1839d. In __get_priority_stripe(),
stripe count equals to 0 initially. Between atomic_inc and BUG_ON,
get_active_stripe() finds the stripe. So the stripe count isn't 1 any more.
V2: keeps the BUG_ON suggested by Neil.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For sequential workload (or request size big workload), get_active_stripe can
find cached stripe. In this case, we always hold device_lock, which exposes a
lot of lock contention for such workload. If stripe count isn't 0, we don't
need hold the lock actually, since we just increase its count. And this is the
hot code path for such workload. Unfortunately we must delete the BUG_ON.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In NUMA machine, prepare_to_wait/finish_wait in make_request exposes a
lot of contention for sequential workload (or big request size
workload). For such workload, each bio includes several stripes. So we
can just do prepare_to_wait/finish_wait once for the whold bio instead
of every stripe. This reduces the lock contention completely for such
workload. Random workload might have the similar lock contention too,
but I didn't see it yet, maybe because my stroage is still not fast
enough.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Interestingly, the raid5 code can actually prevent double initialization and
hence can use the following simplified form of callback registration:
register_cpu_notifier(&foobar_cpu_notifier);
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
put_online_cpus();
A hotplug operation that occurs between registering the notifier and calling
get_online_cpus(), won't disrupt anything, because the code takes care to
perform the memory allocations only once.
So reorganize the code in raid5 this way to fix the deadlock with callback
registration.
Cc: linux-raid@vger.kernel.org
Cc: stable@vger.kernel.org (v2.6.32+)
Fixes: 36d1c6476b
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
[Srivatsa: Fixed the unregister_cpu_notifier() deadlock, added the
free_scratch_buffer() helper to condense code further and wrote the changelog.]
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block IO driver changes from Jens Axboe:
- bcache update from Kent Overstreet.
- two bcache fixes from Nicholas Swenson.
- cciss pci init error fix from Andrew.
- underflow fix in the parallel IDE pg_write code from Dan Carpenter.
I'm sure the 1 (or 0) users of that are now happy.
- two PCI related fixes for sx8 from Jingoo Han.
- floppy init fix for first block read from Jiri Kosina.
- pktcdvd error return miss fix from Julia Lawall.
- removal of IRQF_SHARED from the SEGA Dreamcast CD-ROM code from
Michael Opdenacker.
- comment typo fix for the loop driver from Olaf Hering.
- potential oops fix for null_blk from Raghavendra K T.
- two fixes from Sam Bradshaw (Micron) for the mtip32xx driver, fixing
an OOM problem and a problem with handling security locked conditions
* 'for-3.14/drivers' of git://git.kernel.dk/linux-block: (47 commits)
mg_disk: Spelling s/finised/finished/
null_blk: Null pointer deference problem in alloc_page_buffers
mtip32xx: Correctly handle security locked condition
mtip32xx: Make SGL container per-command to eliminate high order dma allocation
drivers/block/loop.c: fix comment typo in loop_config_discard
drivers/block/cciss.c:cciss_init_one(): use proper errnos
drivers/block/paride/pg.c: underflow bug in pg_write()
drivers/block/sx8.c: remove unnecessary pci_set_drvdata()
drivers/block/sx8.c: use module_pci_driver()
floppy: bail out in open() if drive is not responding to block0 read
bcache: Fix auxiliary search trees for key size > cacheline size
bcache: Don't return -EINTR when insert finished
bcache: Improve bucket_prio() calculation
bcache: Add bch_bkey_equal_header()
bcache: update bch_bkey_try_merge
bcache: Move insert_fixup() to btree_keys_ops
bcache: Convert sorting to btree_keys
bcache: Convert debug code to btree_keys
bcache: Convert btree_iter to struct btree_keys
bcache: Refactor bset_tree sysfs stats
...
Pull core block IO changes from Jens Axboe:
"The major piece in here is the immutable bio_ve series from Kent, the
rest is fairly minor. It was supposed to go in last round, but
various issues pushed it to this release instead. The pull request
contains:
- Various smaller blk-mq fixes from different folks. Nothing major
here, just minor fixes and cleanups.
- Fix for a memory leak in the error path in the block ioctl code
from Christian Engelmayer.
- Header export fix from CaiZhiyong.
- Finally the immutable biovec changes from Kent Overstreet. This
enables some nice future work on making arbitrarily sized bios
possible, and splitting more efficient. Related fixes to immutable
bio_vecs:
- dm-cache immutable fixup from Mike Snitzer.
- btrfs immutable fixup from Muthu Kumar.
- bio-integrity fix from Nic Bellinger, which is also going to stable"
* 'for-3.14/core' of git://git.kernel.dk/linux-block: (44 commits)
xtensa: fixup simdisk driver to work with immutable bio_vecs
block/blk-mq-cpu.c: use hotcpu_notifier()
blk-mq: for_each_* macro correctness
block: Fix memory leak in rw_copy_check_uvector() handling
bio-integrity: Fix bio_integrity_verify segment start bug
block: remove unrelated header files and export symbol
blk-mq: uses page->list incorrectly
blk-mq: use __smp_call_function_single directly
btrfs: fix missing increment of bi_remaining
Revert "block: Warn and free bio if bi_end_io is not set"
block: Warn and free bio if bi_end_io is not set
blk-mq: fix initializing request's start time
block: blk-mq: don't export blk_mq_free_queue()
block: blk-mq: make blk_sync_queue support mq
block: blk-mq: support draining mq queue
dm cache: increment bi_remaining when bi_end_io is restored
block: fixup for generic bio chaining
block: Really silence spurious compiler warnings
block: Silence spurious compiler warnings
block: Kill bio_pair_split()
...
As release_stripe and __release_stripe decrement ->count and then
manipulate ->lru both under ->device_lock, it is important that
get_active_stripe() increments ->count and clears ->lru also under
->device_lock.
However we currently list_del_init ->lru under the lock, but increment
the ->count outside the lock. This can lead to races and list
corruption.
So move the atomic_inc(&sh->count) up inside the ->device_lock
protected region.
Note that we still increment ->count without device lock in the case
where get_free_stripe() was called, and in fact don't take
->device_lock at all in that path.
This is safe because if the stripe_head can be found by
get_free_stripe, then the hash lock assures us the no-one else could
possibly be calling release_stripe() at the same time.
Fixes: 566c09c534
Cc: stable@vger.kernel.org (3.13)
Reported-and-tested-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Before a write starts we set a bit in the write-intent bitmap.
When the write completes we clear that bit if the write was successful
to all devices. However if the write wasn't fully successful we
should not clear the bit. If the faulty drive is subsequently
re-added, the fact that the bit is still set ensure that we will
re-write the data that is missing.
This logic is mediated by the STRIPE_DEGRADED flag - we only clear the
bitmap bit when this flag is not set.
Currently we correctly set the flag if a write starts when some
devices are failed or missing. But we do *not* set the flag if some
device failed during the write attempt.
This is wrong and can result in clearing the bit inappropriately.
So: set the flag when a write fails.
This bug has been present since bitmaps were introduces, so the fix is
suitable for any -stable kernel.
Reported-by: Ethan Wilson <ethan.wilson@shiftmail.org>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
commit 6d183de407
md/raid5: fix newly-broken locking in get_active_stripe.
simplified a BUG_ON, but removed too much so now it sometimes fires
when it shouldn't.
When the STRIPE_EXPANDING flag is set, the stripe_head might be on a
special list while multiple stripe_heads are collected, or it might
not be on any list, even a 'free' list when the refcount is zero. As
long as STRIPE_EXPANDING is set, it will be found and added back to a
list eventually.
So both of the BUG_ONs which test for the ->lru being empty or not
need to avoid the case where STRIPE_EXPANDING is set.
The patch which broke this was marked for -stable, so this patch needs
to be applied to any branch that received 6d183de4
Fixes: 6d183de407
Cc: stable@vger.kernel.org (any release to which above was applied)
Signed-off-by: NeilBrown <neilb@suse.de>
commit 5d8c71f9e5
md: raid5 crash during degradation
Fixed a crash in an overly simplistic way which could leave
R5_WriteError or R5_MadeGood set in the stripe cache for devices
for which it is no longer relevant.
When those devices are removed and spares added the flags are still
set and can cause incorrect behaviour.
commit 14a75d3e07
md/raid5: preferentially read from replacement device if possible.
Fixed the same bug if a more effective way, so we can now revert
the original commit.
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Cc: stable@vger.kernel.org (3.2+ - 3.2 will need a different fix though)
Fixes: 5d8c71f9e5
Signed-off-by: NeilBrown <neilb@suse.de>
Now that we've got code for raid5/6 stripe awareness, bcache just needs
to know about the stripes and when writing partial stripes is expensive
- we probably don't want to enable this optimization for raid1 or 10,
even though they have stripes. So add a flag to queue_limits.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJSwLfoAAoJEHm+PkMAQRiGi6QH/1U1B7lmHChDTw3jj1lfm9gA
189Si4QJlnxFWCKHvKEL+pcaVuACU+aMGI8+KyMYK4/JfuWVjjj5fr/SvyHH2/8m
LdSK8aHMhJ46uBS4WJ/l6v46qQa5e2vn8RKSBAyKm/h4vpt+hd6zJdoFrFai4th7
k/TAwOAEHI5uzexUChwLlUBRTvbq4U8QUvDu+DeifC8cT63CGaaJ4qVzjOZrx1an
eP6UXZrKDASZs7RU950i7xnFVDQu4PsjlZi25udsbeiKcZJgPqGgXz5ULf8ZH8RQ
YCi1JOnTJRGGjyIOyLj7pyB01h7XiSM2+eMQ0S7g54F2s7gCJ58c2UwQX45vRWU=
=/4/R
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc6' into for-3.14/core
Needed to bring blk-mq uptodate, since changes have been going in
since for-3.14/core was established.
Fixup merge issues related to the immutable biovec changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Conflicts:
block/blk-flush.c
fs/btrfs/check-integrity.c
fs/btrfs/extent_io.c
fs/btrfs/scrub.c
fs/logfs/dev_bdev.c
commit 566c09c534 raid5: relieve lock contention in get_active_stripe()
modified the locking in get_active_stripe() reducing the range
protected by the (highly contended) device_lock.
Unfortunately it reduced the range too much opening up some races.
One race can occur if get_priority_stripe runs between the
test on sh->count and device_lock being taken.
This will mean that sh->lru is not empty while get_active_stripe
thinks ->count is zero resulting in a 'BUG' firing.
Another race happens if __release_stripe is called immediately
after sh->count is tested and found to be non-zero. If STRIPE_HANDLE
is not set, get_active_stripe should increment ->active_stripes
when it increments ->count from 0, but as it didn't think it was 0,
it doesn't.
Extending device_lock to cover the test on sh->count close these
races.
While we are here, fix the two BUG tests:
-If count is zero, then lru really must not be empty, or we've
lock the stripe_head somehow - no other tests are relevant.
-STRIPE_ON_RELEASE_LIST is completely independent of ->lru so
testing it is pointless.
Reported-and-tested-by: Brassow Jonathan <jbrassow@redhat.com>
Reviewed-by: Shaohua Li <shli@kernel.org>
Fixes: 566c09c534
Signed-off-by: NeilBrown <neilb@suse.de>
In alloc_thread_groups, worker_groups is a pointer to an array,
not an array of pointers.
So
worker_groups[i]
is wrong. It should be
&(*worker_groups)[i]
Found-by: coverity
Fixes: 60aaf93385
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
More prep work for immutable biovecs - with immutable bvecs drivers
won't be able to use the biovec directly, they'll need to use helpers
that take into account bio->bi_iter.bi_bvec_done.
This updates callers for the new usage without changing the
implementation yet.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: Jim Paris <jim@jtan.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@inktank.com>
Cc: ceph-devel@vger.kernel.org
Cc: Joshua Morris <josh.h.morris@us.ibm.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Guo Chao <yan@linux.vnet.ibm.com>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Quoc-Son Anh <quoc-sonx.anh@intel.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jan Kara <jack@suse.cz>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: drbd-user@lists.linbit.com
Cc: nbd-general@lists.sourceforge.net
Cc: cbe-oss-dev@lists.ozlabs.org
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.linux-foundation.org
Cc: linux-raid@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: linux-fsdevel@vger.kernel.org
Cc: cluster-devel@redhat.com
Cc: linux-mm@kvack.org
Acked-by: Geoff Levand <geoff@infradead.org>
Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io
during resync.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8RCg
-----END PGP SIGNATURE-----
Merge tag 'md/3.13' of git://neil.brown.name/md
Pull md update from Neil Brown:
"Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io during
resync"
* tag 'md/3.13' of git://neil.brown.name/md:
md/raid5: Use conf->device_lock protect changing of multi-thread resources.
md/raid5: Before freeing old multi-thread worker, it should flush them.
md/raid5: For stripe with R5_ReadNoMerge, we replace REQ_FLUSH with REQ_NOMERGE.
UAPI: include <asm/byteorder.h> in linux/raid/md_p.h
raid1: Rewrite the implementation of iobarrier.
raid1: Add some macros to make code clearly.
raid1: Replace raise_barrier/lower_barrier with freeze_array/unfreeze_array when reconfiguring the array.
raid1: Add a field array_frozen to indicate whether raid in freeze state.
md: Convert use of typedef ctl_table to struct ctl_table
md/raid5: avoid deadlock when raid5 array has unack badblocks during md_stop_writes.
md: use MD_RECOVERY_INTR instead of kthread_should_stop in resync thread.
md: fix some places where mddev_lock return value is not checked.
raid5: Retry R5_ReadNoMerge flag when hit a read error.
raid5: relieve lock contention in get_active_stripe()
raid5: relieve lock contention in get_active_stripe()
wait: add wait_event_cmd()
md/raid5.c: add proper locking to error path of raid5_start_reshape.
md: fix calculation of stacking limits on level change.
raid5: Use slow_path to release stripe when mddev->thread is null
For R5_ReadNoMerge,it mean this bio can't merge with other bios or
request.It used REQ_FLUSH to achieve this. But REQ_NOMERGE can do the
same work.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We currently use kthread_should_stop() in various places in the
sync/reshape code to abort early.
However some places set MD_RECOVERY_INTR but don't immediately call
md_reap_sync_thread() (and we will shortly get another one).
When this happens we are relying on md_check_recovery() to reap the
thread and that only happen when it finishes normally.
So MD_RECOVERY_INTR must lead to a normal finish without the
kthread_should_stop() test.
So replace all relevant tests, and be more careful when the thread is
interrupted not to acknowledge that latest step in a reshape as it may
not be fully committed yet.
Also add a test on MD_RECOVERY_INTR in the 'is_mddev_idle' loop
so we don't wait have to wait for the speed to drop before we can abort.
Signed-off-by: NeilBrown <neilb@suse.de>
Because of block layer merge, one bio fails will cause other bios
which belongs to the same request fails, so raid5_end_read_request
will record all these bios as badblocks.
If retry request with R5_ReadNoMerge flag to avoid bios merge,
badblocks can only record sector which is bad exactly.
test:
hdparm --yes-i-know-what-i-am-doing --make-bad-sector 300000 /dev/sdb
mdadm -C /dev/md0 -l5 -n3 /dev/sd[bcd] --assume-clean
mdadm /dev/md0 -f /dev/sdd
mdadm /dev/md0 -r /dev/sdd
mdadm --zero-superblock /dev/sdd
mdadm /dev/md0 -a /dev/sdd
1. Without this patch:
cat /sys/block/md0/md/rd*/bad_blocks
299776 256
299776 256
2. With this patch:
cat /sys/block/md0/md/rd*/bad_blocks
300000 8
300000 8
Signed-off-by: Bian Yu <bianyu@kedacom.com>
Signed-off-by: NeilBrown <neilb@suse.de>
track empty inactive list count, so md_raid5_congested() can use it to make
decision.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Make this useful helper available for other users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_active_stripe() is the last place we have lock contention. It has two
paths. One is stripe isn't found and new stripe is allocated, the other is
stripe is found.
The first path basically calls __find_stripe and init_stripe. It accesses
conf->generation, conf->previous_raid_disks, conf->raid_disks,
conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded,
conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except
stripe_hashtbl and inactive_list, other fields are changed very rarely.
With this patch, we split inactive_list and add new hash locks. Each free
stripe belongs to a specific inactive list. Which inactive list is determined
by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a
lock_hash assigned. Stripe's inactive list is protected by a hash lock, which
is determined by it's lock_hash too. The lock_hash is derivied from current
stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned
to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl
list too. The goal of the new hash locks introduced is we can only use the new
locks in the first path of get_active_stripe(). Since we have several hash
locks, lock contention is relieved significantly.
The first path of get_active_stripe() accesses other fields, since they are
changed rarely, changing them now need take conf->device_lock and all hash
locks. For a slow path, this isn't a problem.
If we need lock device_lock and hash lock, we always lock hash lock first. The
tricky part is release_stripe and friends. We need take device_lock first.
Neil's suggestion is we put inactive stripes to a temporary list and readd it
to inactive_list after device_lock is released. In this way, we add stripes to
temporary list with device_lock hold and remove stripes from the list with hash
lock hold. So we don't allow concurrent access to the temporary list, which
means we need allocate temporary list for all participants of release_stripe.
One downside is free stripes are maintained in their inactive list, they can't
across between the lists. By default, we have total 256 stripes and 8 lists, so
each list will have 32 stripes. It's possible one list has free stripe but
other list hasn't. The chance should be rare because stripes allocation are
even distributed. And we can always allocate more stripes for cache, several
mega bytes memory isn't a big deal.
This completely removes the lock contention of the first path of
get_active_stripe(). It slows down the second code path a little bit though
because we now need takes two locks, but since the hash lock isn't contended,
the overhead should be quite small (several atomic instructions). The second
path of get_active_stripe() (basically sequential write or big request size
randwrite) still has lock contentions.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If raid5_start_reshape errors out, we need to reset all the fields
that were updated (not just some), and need to use the seq_counter
to ensure make_request() doesn't use an inconsitent state.
Signed-off-by: NeilBrown <neilb@suse.de>
When release_stripe() is called in grow_one_stripe(), the
mddev->thread is null. So it will omit one wakeup this thread to
release stripe.
For this condition, use slow_path to release stripe.
Bug was introduced in 3.12
Cc: stable@vger.kernel.org (3.12+)
Fixes: 773ca82fa1
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
SCSI discard will damage discard stripe bio setting, eg, some fields are
changed. If the stripe is reused very soon, we have wrong bios setting. We
remove discard stripe from hash list, so next time the strip will be fully
initialized.
Suitable for backport to 3.7+.
Cc: <stable@vger.kernel.org> (3.7+)
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
SCSI layer will add new payload for discard request. If two bios are merged
to one, the second bio has bi_vcnt 1 which is set in raid5. This will confuse
SCSI and cause oops.
Suitable for backport to 3.7+
Cc: stable@vger.kernel.org (v3.7+)
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
If there are not enough stripes to handle, we'd better not always
queue all available work_structs. If one worker can only handle small
or even none stripes, it will impact request merge and create lock
contention.
With this patch, the number of work_struct running will depend on
pending stripes number. Note: some statistics info used in the patch
are accessed without locking protection. This should doesn't matter,
we just try best to avoid queue unnecessary work_struct.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some requests - particularly 'discard' and 'read' are handled
differently depending on whether a reshape is active or not.
It is harmless to assume reshape is active if it isn't but wrong
to act as though reshape is not active when it is.
So when we start reshape - after making clear to all requests that
reshape has started - use mddev_suspend/mddev_resume to flush out all
requests. This will ensure that no requests will be assuming the
absence of reshape once it really starts.
Signed-off-by: NeilBrown <neilb@suse.de>
make_request() access various shape parameters (raid_disks, chunk_size
etc) which might be changed by raid5_start_reshape().
If the later is called at and awkward time during the form, the wrong
stripe_head might be used.
So introduce a 'seqcount' and after finding a stripe_head make sure
there is no reason to expect that we got the wrong one.
Signed-off-by: NeilBrown <neilb@suse.de>
