TCP_NOTSENT_LOWAT socket option or sysctl was added in linux-3.12
as a step to enable bigger tcp sndbuf limits.
It works reasonably well, but the following happens :
Once the limit is reached, TCP stack generates
an [E]POLLOUT event for every incoming ACK packet.
This causes a high number of context switches.
This patch implements the strategy David Miller added
in sock_def_write_space() :
- If TCP socket has a notsent_lowat constraint of X bytes,
allow sendmsg() to fill up to X bytes, but send [E]POLLOUT
only if number of notsent bytes is below X/2
This considerably reduces TCP_NOTSENT_LOWAT overhead,
while allowing to keep the pipe full.
Tested:
100 ms RTT netem testbed between A and B, 100 concurrent TCP_STREAM
A:/# cat /proc/sys/net/ipv4/tcp_wmem
4096 262144 64000000
A:/# super_netperf 100 -H B -l 1000 -- -K bbr &
A:/# grep TCP /proc/net/sockstat
TCP: inuse 203 orphan 0 tw 19 alloc 414 mem 1364904 # This is about 54 MB of memory per flow :/
A:/# vmstat 5 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
0 0 0 256220672 13532 694976 0 0 10 0 28 14 0 1 99 0 0
2 0 0 256320016 13532 698480 0 0 512 0 715901 5927 0 10 90 0 0
0 0 0 256197232 13532 700992 0 0 735 13 771161 5849 0 11 89 0 0
1 0 0 256233824 13532 703320 0 0 512 23 719650 6635 0 11 89 0 0
2 0 0 256226880 13532 705780 0 0 642 4 775650 6009 0 12 88 0 0
A:/# echo 2097152 >/proc/sys/net/ipv4/tcp_notsent_lowat
A:/# grep TCP /proc/net/sockstat
TCP: inuse 203 orphan 0 tw 19 alloc 414 mem 86411 # 3.5 MB per flow
A:/# vmstat 5 5 # check that context switches have not inflated too much.
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
2 0 0 260386512 13592 662148 0 0 10 0 17 14 0 1 99 0 0
0 0 0 260519680 13592 604184 0 0 512 13 726843 12424 0 10 90 0 0
1 1 0 260435424 13592 598360 0 0 512 25 764645 12925 0 10 90 0 0
1 0 0 260855392 13592 578380 0 0 512 7 722943 13624 0 11 88 0 0
1 0 0 260445008 13592 601176 0 0 614 34 772288 14317 0 10 90 0 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to set a tunnel without a destination port. However,
on dump(), a zero dst port is returned to user space even if it was not
set, fix that.
Note that so far it wasn't required, b/c key less tunnels were not
supported and the UDP tunnels do require destination port.
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow setting a tunnel without a tunnel key. This is required for
tunneling protocols, such as GRE, that define the key as an optional
field.
Signed-off-by: Adi Nissim <adin@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets marked with 'offload_l3_fwd_mark' were already forwarded by a
capable device and should not be forwarded again by the kernel.
Therefore, have the kernel consume them.
The check is performed in ip{,6}_forward_finish() in order to allow the
kernel to process such packets in ip{,6}_forward() and generate required
exceptions. For example, ICMP redirects.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit abf4bb6b63 ("skbuff: Add the offload_mr_fwd_mark field") added
the 'offload_mr_fwd_mark' field to indicate that a packet has already
undergone L3 multicast routing by a capable device. The field is used to
prevent the kernel from forwarding a packet through a netdev through
which the device has already forwarded the packet.
Currently, no unicast packet is routed by both the device and the
kernel, but this is about to change by subsequent patches and we need to
be able to mark such packets, so that they will no be forwarded twice.
Instead of adding yet another field to 'struct sk_buff', we can just
rename 'offload_mr_fwd_mark' to 'offload_l3_fwd_mark', as a packet
either has a multicast or a unicast destination IP.
While at it, add a comment about both 'offload_fwd_mark' and
'offload_l3_fwd_mark'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With MSG_ZEROCOPY, each skb holds a reference to a struct ubuf_info.
Release of its last reference triggers a completion notification.
The TCP stack in tcp_sendmsg_locked holds an extra ref independent of
the skbs, because it can build, send and free skbs within its loop,
possibly reaching refcount zero and freeing the ubuf_info too soon.
The UDP stack currently also takes this extra ref, but does not need
it as all skbs are sent after return from __ip(6)_append_data.
Avoid the extra refcount_inc and refcount_dec_and_test, and generally
the sock_zerocopy_put in the common path, by passing the initial
reference to the first skb.
This approach is taken instead of initializing the refcount to 0, as
that would generate error "refcount_t: increment on 0" on the
next skb_zcopy_set.
Changes
v3 -> v4
- Move skb_zcopy_set below the only kfree_skb that might cause
a premature uarg destroy before skb_zerocopy_put_abort
- Move the entire skb_shinfo assignment block, to keep that
cacheline access in one place
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend zerocopy to udp sockets. Allow setting sockopt SO_ZEROCOPY and
interpret flag MSG_ZEROCOPY.
This patch was previously part of the zerocopy RFC patchsets. Zerocopy
is not effective at small MTU. With segmentation offload building
larger datagrams, the benefit of page flipping outweights the cost of
generating a completion notification.
tools/testing/selftests/net/msg_zerocopy.sh after applying follow-on
test patch and making skb_orphan_frags_rx same as skb_orphan_frags:
ipv4 udp -t 1
tx=191312 (11938 MB) txc=0 zc=n
rx=191312 (11938 MB)
ipv4 udp -z -t 1
tx=304507 (19002 MB) txc=304507 zc=y
rx=304507 (19002 MB)
ok
ipv6 udp -t 1
tx=174485 (10888 MB) txc=0 zc=n
rx=174485 (10888 MB)
ipv6 udp -z -t 1
tx=294801 (18396 MB) txc=294801 zc=y
rx=294801 (18396 MB)
ok
Changes
v1 -> v2
- Fixup reverse christmas tree violation
v2 -> v3
- Split refcount avoidance optimization into separate patch
- Fix refcount leak on error in fragmented case
(thanks to Paolo Abeni for pointing this one out!)
- Fix refcount inc on zero
- Test sock_flag SOCK_ZEROCOPY directly in __ip_append_data.
This is needed since commit 5cf4a8532c ("tcp: really ignore
MSG_ZEROCOPY if no SO_ZEROCOPY") did the same for tcp.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have of_get_nvmem_mac_address() but some non-DT systems want
to read the MAC address from NVMEM too. Implement a generalized routine
that takes struct device as argument.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing functions to retreive the l3mdev of a device did not walk the
master chain to find the upper master. This patch adds a function to
find the l3mdev, even indirect through e.g. a bridge:
+----------+
| |
| vrf-blue |
| |
+----+-----+
|
|
+----+-----+
| |
| br-blue |
| |
+----+-----+
|
|
+----+-----+
| |
| eth0 |
| |
+----------+
This will properly resolve the l3mdev of eth0 to vrf-blue.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP tunnel sockets are always opened unbound to a specific device. This
patch allow the socket to be bound on a custom device, which
incidentally makes UDP tunnels VRF-aware if binding to an l3mdev.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers load the device's firmware image during the initialization
flow either from the flash or from the disk. Currently this option is not
controlled by the user and the driver decides from where to load the
firmware image.
'fw_load_policy' gives the ability to control this option which allows the
user to choose between different loading policies supported by the driver.
This parameter can be useful while testing and/or debugging the device. For
example, testing a firmware bug fix.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the function only works for the bridge device itself, but
subsequent patches will need to be able to query the PVID of a given
bridge port, so extend the function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Standard kernel compilation produces the following warning:
net/core/rtnetlink.c: In function ‘rtnl_newlink’:
net/core/rtnetlink.c:3232:1: warning: the frame size of 1288 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
This should not really be an issue, as rtnl_newlink() stack is
generally quite shallow.
Fix the warning by allocating attributes with kmalloc() in a wrapper
and passing it down to rtnl_newlink(), avoiding complexities on error
paths.
Alternatively we could kmalloc() some structure within rtnl_newlink(),
slave attributes look like a good candidate. In practice it adds to
already rather high complexity and length of the function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_newlink() used to create VLAs based on link kind. Since
commit ccf8dbcd06 ("rtnetlink: Remove VLA usage") statically
sized array is created on the stack, so there is no more use
for a separate code block that used to be the VLA's live range.
While at it christmas tree the variables. Note that there is
a goto-based retry so to be on the safe side the variables can
no longer be initialized in place. It doesn't seem to matter,
logically, but why make the code harder to read..
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most linux hosts never setup TCP MD5 keys. We can avoid a
cache line miss (accessing tp->md5ig_info) on RX and TX
using a jump label.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case GRO is not as efficient as it should be or disabled,
we might have a user thread trapped in __release_sock() while
softirq handler flood packets up to the point we have to drop.
This patch balances work done from user thread and softirq,
to give more chances to __release_sock() to complete its work
before new packets are added the the backlog.
This also helps if we receive many ACK packets, since GRO
does not aggregate them.
This patch brings ~60% throughput increase on a receiver
without GRO, but the spectacular gain is really on
1000x release_sock() latency reduction I have measured.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neal pointed out that non sack flows might suffer from ACK compression
added in the following patch ("tcp: implement coalescing on backlog queue")
Instead of tweaking tcp_add_backlog() we can take into
account how many ACK were coalesced, this information
will be available in skb_shinfo(skb)->gso_segs
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trace events are already present for the receive entry points, to indicate
how the reception entered the stack.
This patch adds the corresponding exit trace events that will bound the
reception such that all events occurring between the entry and the exit
can be considered as part of the reception context. This greatly helps
for dependency and root cause analyses.
Without this, it is not possible with tracepoint instrumentation to
determine whether a sched_wakeup event following a netif_receive_skb
event is the result of the packet reception or a simple coincidence after
further processing by the thread. It is possible using other mechanisms
like kretprobes, but considering the "entry" points are already present,
it would be good to add the matching exit events.
In addition to linking packets with wakeups, the entry/exit event pair
can also be used to perform network stack latency analyses.
Signed-off-by: Geneviève Bastien <gbastien@versatic.net>
CC: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Ingo Molnar <mingo@redhat.com>
CC: David S. Miller <davem@davemloft.net>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> (tracing side)
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
bpf-next 2018-11-30
The following pull-request contains BPF updates for your *net-next* tree.
(Getting out bit earlier this time to pull in a dependency from bpf.)
The main changes are:
1) Add libbpf ABI versioning and document API naming conventions
as well as ABI versioning process, from Andrey.
2) Add a new sk_msg_pop_data() helper for sk_msg based BPF
programs that is used in conjunction with sk_msg_push_data()
for adding / removing meta data to the msg data, from John.
3) Optimize convert_bpf_ld_abs() for 0 offset and fix various
lib and testsuite build failures on 32 bit, from David.
4) Make BPF prog dump for !JIT identical to how we dump subprogs
when JIT is in use, from Yonghong.
5) Rename btf_get_from_id() to make it more conform with libbpf
API naming conventions, from Martin.
6) Add a missing BPF kselftest config item, from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove the loop and conditional branches
and compute wscale efficiently thanks to ilog2()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a BPF SK_MSG program helper so that we can pop data from a
msg. We use this to pop metadata from a previous push data call.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Disable BH while holding list spinlock in nf_conncount, from
Taehee Yoo.
2) List corruption in nf_conncount, also from Taehee.
3) Fix race that results in leaving around an empty list node in
nf_conncount, from Taehee Yoo.
4) Proper chain handling for inactive chains from the commit path,
from Florian Westphal. This includes a selftest for this.
5) Do duplicate rule handles when replacing rules, also from Florian.
6) Remove net_exit path in xt_RATEEST that results in splat, from Taehee.
7) Possible use-after-free in nft_compat when releasing extensions.
From Florian.
8) Memory leak in xt_hashlimit, from Taehee.
9) Call ip_vs_dst_notifier after ipv6_dev_notf, from Xin Long.
10) Fix cttimeout with udplite and gre, from Florian.
11) Preserve oif for IPv6 link-local generated traffic from mangle
table, from Alin Nastac.
12) Missing error handling in masquerade notifiers, from Taehee Yoo.
13) Use mutex to protect registration/unregistration of masquerade
extensions in order to prevent a race, from Taehee.
14) Incorrect condition check in tree_nodes_free(), also from Taehee.
15) Fix chain counter leak in rule replacement path, from Taehee.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy reported when CONFIG_PROC_FS is not enabled:
ld: net/ipv4/af_inet.o: in function `inet_init':
af_inet.c:(.init.text+0x42d): undefined reference to `raw_init'
Fix by moving the endif up to the end of the proc entries
Fixes: 6897445fb1 ("net: provide a sysctl raw_l3mdev_accept for raw socket lookup with VRFs")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mike Manning <mmanning@vyatta.att-mail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one caller needs to pull TCP headers, so lets
move __skb_pull() to the caller side.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OEM Mellanox commands and response handling. It also
defines OEM Get MAC Address handler to get and configure the device.
ncsi_oem_gma_handler_mlx: This handler send NCSI mellanox command for
getting mac address.
ncsi_rsp_handler_oem_mlx: This handles response received for all
mellanox OEM commands.
ncsi_rsp_handler_oem_mlx_gma: This handles get mac address response and
set it to device.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We see the following lockdep warning:
[ 2284.078521] ======================================================
[ 2284.078604] WARNING: possible circular locking dependency detected
[ 2284.078604] 4.19.0+ #42 Tainted: G E
[ 2284.078604] ------------------------------------------------------
[ 2284.078604] rmmod/254 is trying to acquire lock:
[ 2284.078604] 00000000acd94e28 ((&n->timer)#2){+.-.}, at: del_timer_sync+0x5/0xa0
[ 2284.078604]
[ 2284.078604] but task is already holding lock:
[ 2284.078604] 00000000f997afc0 (&(&tn->node_list_lock)->rlock){+.-.}, at: tipc_node_stop+0xac/0x190 [tipc]
[ 2284.078604]
[ 2284.078604] which lock already depends on the new lock.
[ 2284.078604]
[ 2284.078604]
[ 2284.078604] the existing dependency chain (in reverse order) is:
[ 2284.078604]
[ 2284.078604] -> #1 (&(&tn->node_list_lock)->rlock){+.-.}:
[ 2284.078604] tipc_node_timeout+0x20a/0x330 [tipc]
[ 2284.078604] call_timer_fn+0xa1/0x280
[ 2284.078604] run_timer_softirq+0x1f2/0x4d0
[ 2284.078604] __do_softirq+0xfc/0x413
[ 2284.078604] irq_exit+0xb5/0xc0
[ 2284.078604] smp_apic_timer_interrupt+0xac/0x210
[ 2284.078604] apic_timer_interrupt+0xf/0x20
[ 2284.078604] default_idle+0x1c/0x140
[ 2284.078604] do_idle+0x1bc/0x280
[ 2284.078604] cpu_startup_entry+0x19/0x20
[ 2284.078604] start_secondary+0x187/0x1c0
[ 2284.078604] secondary_startup_64+0xa4/0xb0
[ 2284.078604]
[ 2284.078604] -> #0 ((&n->timer)#2){+.-.}:
[ 2284.078604] del_timer_sync+0x34/0xa0
[ 2284.078604] tipc_node_delete+0x1a/0x40 [tipc]
[ 2284.078604] tipc_node_stop+0xcb/0x190 [tipc]
[ 2284.078604] tipc_net_stop+0x154/0x170 [tipc]
[ 2284.078604] tipc_exit_net+0x16/0x30 [tipc]
[ 2284.078604] ops_exit_list.isra.8+0x36/0x70
[ 2284.078604] unregister_pernet_operations+0x87/0xd0
[ 2284.078604] unregister_pernet_subsys+0x1d/0x30
[ 2284.078604] tipc_exit+0x11/0x6f2 [tipc]
[ 2284.078604] __x64_sys_delete_module+0x1df/0x240
[ 2284.078604] do_syscall_64+0x66/0x460
[ 2284.078604] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 2284.078604]
[ 2284.078604] other info that might help us debug this:
[ 2284.078604]
[ 2284.078604] Possible unsafe locking scenario:
[ 2284.078604]
[ 2284.078604] CPU0 CPU1
[ 2284.078604] ---- ----
[ 2284.078604] lock(&(&tn->node_list_lock)->rlock);
[ 2284.078604] lock((&n->timer)#2);
[ 2284.078604] lock(&(&tn->node_list_lock)->rlock);
[ 2284.078604] lock((&n->timer)#2);
[ 2284.078604]
[ 2284.078604] *** DEADLOCK ***
[ 2284.078604]
[ 2284.078604] 3 locks held by rmmod/254:
[ 2284.078604] #0: 000000003368be9b (pernet_ops_rwsem){+.+.}, at: unregister_pernet_subsys+0x15/0x30
[ 2284.078604] #1: 0000000046ed9c86 (rtnl_mutex){+.+.}, at: tipc_net_stop+0x144/0x170 [tipc]
[ 2284.078604] #2: 00000000f997afc0 (&(&tn->node_list_lock)->rlock){+.-.}, at: tipc_node_stop+0xac/0x19
[...}
The reason is that the node timer handler sometimes needs to delete a
node which has been disconnected for too long. To do this, it grabs
the lock 'node_list_lock', which may at the same time be held by the
generic node cleanup function, tipc_node_stop(), during module removal.
Since the latter is calling del_timer_sync() inside the same lock, we
have a potential deadlock.
We fix this letting the timer cleanup function use spin_trylock()
instead of just spin_lock(), and when it fails to grab the lock it
just returns so that the timer handler can terminate its execution.
This is safe to do, since tipc_node_stop() anyway is about to
delete both the timer and the node instance.
Fixes: 6a939f365b ("tipc: Auto removal of peer down node instance")
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the previous patch, the goal is to ease to convert nsids from one
netns to another netns.
A new attribute (NETNSA_CURRENT_NSID) is added to the kernel answer when
NETNSA_TARGET_NSID is provided, thus the user can easily convert nsids.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combined with NETNSA_TARGET_NSID, it enables to "translate" a nsid from one
netns to a nsid of another netns.
This is useful when using NETLINK_F_LISTEN_ALL_NSID because it helps the
user to interpret a nsid received from an other netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like it was done for link and address, add the ability to perform get/dump
in another netns by specifying a target nsid attribute.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparatory work. To avoid having to much arguments for the
function rtnl_net_fill(), a new structure is defined.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used anymore.
Fixes: cab3c8ec8d ("netns: always provide the id to rtnl_net_fill()")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I changed to count sk_wmem_alloc by skb truesize instead of 1 to
fix the sk_wmem_alloc leak caused by later truesize's change in
xfrm in Commit 02968ccf01 ("sctp: count sk_wmem_alloc by skb
truesize in sctp_packet_transmit").
But I should have also increased sk_wmem_alloc when head->truesize
is increased in sctp_packet_gso_append() as xfrm does. Otherwise,
sctp gso packet will cause sk_wmem_alloc underflow.
Fixes: 02968ccf01 ("sctp: count sk_wmem_alloc by skb truesize in sctp_packet_transmit")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have at least one bool option, we can export all of the
supported bool options via optmask when dumping them.
v2: new patch
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new boolopt API to add an option which disables learning from
link-local packets. The default is kept as before and learning is
enabled. This is a simple map from a boolopt bit to a bridge private
flag that is tested before learning.
v2: pass NULL for extack via sysfs
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been adding many new bridge options, a big number of which are
boolean but still take up netlink attribute ids and waste space in the skb.
Recently we discussed learning from link-local packets[1] and decided
yet another new boolean option will be needed, thus introducing this API
to save some bridge nl space.
The API supports changing the value of multiple boolean options at once
via the br_boolopt_multi struct which has an optmask (which options to
set, bit per opt) and optval (options' new values). Future boolean
options will only be added to the br_boolopt_id enum and then will have
to be handled in br_boolopt_toggle/get. The API will automatically
add the ability to change and export them via netlink, sysfs can use the
single boolopt function versions to do the same. The behaviour with
failing/succeeding is the same as with normal netlink option changing.
If an option requires mapping to internal kernel flag or needs special
configuration to be enabled then it should be handled in
br_boolopt_toggle. It should also be able to retrieve an option's current
state via br_boolopt_get.
v2: WARN_ON() on unsupported option as that shouldn't be possible and
also will help catch people who add new options without handling
them for both set and get. Pass down extack so if an option desires
it could set it on error and be more user-friendly.
[1] https://www.spinics.net/lists/netdev/msg532698.html
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All lists that reach the tree_nodes_free() function have both zero
counter and true dead flag. The reason for this is that lists to be
release are selected by nf_conncount_gc_list() which already decrements
the list counter and sets on the dead flag. Therefore, this if statement
in tree_nodes_free() is unnecessary and wrong.
Fixes: 31568ec09e ("netfilter: nf_conncount: fix list_del corruption in conn_free")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
register_{netdevice/inetaddr/inet6addr}_notifier may return an error
value, this patch adds the code to handle these error paths.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When ip6_route_me_harder is invoked, it resets outgoing interface of:
- link-local scoped packets sent by neighbor discovery
- multicast packets sent by MLD host
- multicast packets send by MLD proxy daemon that sets outgoing
interface through IPV6_PKTINFO ipi6_ifindex
Link-local and multicast packets must keep their original oif after
ip6_route_me_harder is called.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
'offset' is constant and if it is zero, no need to subtract it
from BPF_REG_TMP.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-11-26
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Extend BTF to support function call types and improve the BPF
symbol handling with this info for kallsyms and bpftool program
dump to make debugging easier, from Martin and Yonghong.
2) Optimize LPM lookups by making longest_prefix_match() handle
multiple bytes at a time, from Eric.
3) Adds support for loading and attaching flow dissector BPF progs
from bpftool, from Stanislav.
4) Extend the sk_lookup() helper to be supported from XDP, from Nitin.
5) Enable verifier to support narrow context loads with offset > 0
to adapt to LLVM code generation (currently only offset of 0 was
supported). Add test cases as well, from Andrey.
6) Simplify passing device functions for offloaded BPF progs by
adding callbacks to bpf_prog_offload_ops instead of ndo_bpf.
Also convert nfp and netdevsim to make use of them, from Quentin.
7) Add support for sock_ops based BPF programs to send events to
the perf ring-buffer through perf_event_output helper, from
Sowmini and Daniel.
8) Add read / write support for skb->tstamp from tc BPF and cg BPF
programs to allow for supporting rate-limiting in EDT qdiscs
like fq from BPF side, from Vlad.
9) Extend libbpf API to support map in map types and add test cases
for it as well to BPF kselftests, from Nikita.
10) Account the maximum packet offset accessed by a BPF program in
the verifier and use it for optimizing nfp JIT, from Jiong.
11) Fix error handling regarding kprobe_events in BPF sample loader,
from Daniel T.
12) Add support for queue and stack map type in bpftool, from David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot was able to trigger the WARN in cttimeout_default_get() by
passing UDPLITE as l4protocol. Alias UDPLITE to UDP, both use
same timeout values.
Furthermore, also fetch GRE timeouts. GRE is a bit more complicated,
as it still can be a module and its netns_proto_gre struct layout isn't
visible outside of the gre module. Can't move timeouts around, it
appears conntrack sysctl unregister assumes net_generic() returns
nf_proto_net, so we get crash. Expose layout of netns_proto_gre instead.
A followup nf-next patch could make gre tracker be built-in as well
if needed, its not that large.
Last, make the WARN() mention the missing protocol value in case
anything else is missing.
Reported-by: syzbot+2fae8fa157dd92618cae@syzkaller.appspotmail.com
Fixes: 8866df9264 ("netfilter: nfnetlink_cttimeout: pass default timeout policy to obj_to_nlattr")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ip_vs_dst_event is supposed to clean up all dst used in ipvs'
destinations when a net dev is going down. But it works only
when the dst's dev is the same as the dev from the event.
Now with the same priority but late registration,
ip_vs_dst_notifier is always called later than ipv6_dev_notf
where the dst's dev is set to lo for NETDEV_DOWN event.
As the dst's dev lo is not the same as the dev from the event
in ip_vs_dst_event, ip_vs_dst_notifier doesn't actually work.
Also as these dst have to wait for dest_trash_timer to clean
them up. It would cause some non-permanent kernel warnings:
unregister_netdevice: waiting for br0 to become free. Usage count = 3
To fix it, call ip_vs_dst_notifier earlier than ipv6_dev_notf
by increasing its priority to ADDRCONF_NOTIFY_PRIORITY + 5.
Note that for ipv4 route fib_netdev_notifier doesn't set dst's
dev to lo in NETDEV_DOWN event, so this fix is only needed when
IP_VS_IPV6 is defined.
Fixes: 7a4f0761fc ("IPVS: init and cleanup restructuring")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Daniel Borkmann says:
====================
pull-request: bpf 2018-11-25
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix an off-by-one bug when adjusting subprog start offsets after
patching, from Edward.
2) Fix several bugs such as overflow in size allocation in queue /
stack map creation, from Alexei.
3) Fix wrong IPv6 destination port byte order in bpf_sk_lookup_udp
helper, from Andrey.
4) Fix several bugs in bpftool such as preventing an infinite loop
in get_fdinfo, error handling and man page references, from Quentin.
5) Fix a warning in bpf_trace_printk() that wasn't catching an
invalid format string, from Martynas.
6) Fix a bug in BPF cgroup local storage where non-atomic allocation
was used in atomic context, from Roman.
7) Fix a NULL pointer dereference bug in bpftool from reallocarray()
error handling, from Jakub and Wen.
8) Add a copy of pkt_cls.h and tc_bpf.h uapi headers to the tools
include infrastructure so that bpftool compiles on older RHEL7-like
user space which does not ship these headers, from Yonghong.
9) Fix BPF kselftests for user space where to get ping test working
with ping6 and ping -6, from Li.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I do not see how one can effectively use skb_insert() without holding
some kind of lock. Otherwise other cpus could have changed the list
right before we have a chance of acquiring list->lock.
Only existing user is in drivers/infiniband/hw/nes/nes_mgt.c and this
one probably meant to use __skb_insert() since it appears nesqp->pau_list
is protected by nesqp->pau_lock. This looks like nesqp->pau_lock
could be removed, since nesqp->pau_list.lock could be used instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma <linux-rdma@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change added a null check on p->dev after p->dev was being
dereferenced by the ns_capable check on p->dev. It turns out that
neither the p->dev and p->br null checks are necessary, and can be
removed, which cleans up a static analyis warning.
As Nikolay Aleksandrov noted, these checks can be removed because:
"My reasoning of why it shouldn't be possible:
- On port add new_nbp() sets both p->dev and p->br before creating
kobj/sysfs
- On port del (trickier) del_nbp() calls kobject_del() before call_rcu()
to destroy the port which in turn calls sysfs_remove_dir() which uses
kernfs_remove() which deactivates (shouldn't be able to open new
files) and calls kernfs_drain() to drain current open/mmaped files in
the respective dir before continuing, thus making it impossible to
open a bridge port sysfs file with p->dev and p->br equal to NULL.
So I think it's safe to remove those checks altogether. It'd be nice to
get a second look over my reasoning as I might be missing something in
sysfs/kernfs call path."
Thanks to Nikolay Aleksandrov's suggestion to remove the check and
David Miller for sanity checking this.
Detected by CoverityScan, CID#751490 ("Dereference before null check")
Fixes: a5f3ea54f3 ("net: bridge: add support for raw sysfs port options")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip packet generation, pagedlen is initialized for each skb at the
start of the loop in __ip(6)_append_data, before label alloc_new_skb.
Depending on compiler options, code can be generated that jumps to
this label, triggering use of an an uninitialized variable.
In practice, at -O2, the generated code moves the initialization below
the label. But the code should not rely on that for correctness.
Fixes: 15e36f5b8e ("udp: paged allocation with gso")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
