It seems that the checked range for receiver window check should
begin from the first rather than from the last skb that is going
to be included to the probe. And that can be achieved without
reference to skbs at all, snd_nxt and write_seq provides the
correct seqno already. Plus, it SHOULD account packets that are
necessary to trigger fast retransmit [RFC4821].
Location of snd_wnd < probe_size/size_needed check is bogus
because it will cause the other if() match as well (due to
snd_nxt >= snd_una invariant).
Removed dead obvious comment.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SPIN_LOCK_UNLOCKED is deprecated, use DEFINE_SPINLOCK instead
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
xs_setup_{udp,tcp}() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
From: Charles Hardin <chardin@2wire.com>
Kernel needs to respond to an SADB_GET with the same message type to
conform to the RFC 2367 Section 3.1.5
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Found this occasionally.
The CONFIG_INET=n is hardly ever set, but if it is the
irlan_eth_send_gratuitous_arp() compilation should produce a
warning about unused variable in_dev.
Too pedantic? :)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is silly, but I have turned the CONFIG_IP_VS to m,
to check the compilation of one (recently sent) fix
and set all the CONFIG_IP_VS_PROTO_XXX options to n to
speed up the compilation.
In this configuration the compiler warns me about
CC [M] net/ipv4/ipvs/ip_vs_proto.o
net/ipv4/ipvs/ip_vs_proto.c:49: warning: 'register_ip_vs_protocol' defined but not used
Indeed. With no protocols selected there are no
calls to this function - all are compiled out with
ifdefs.
Maybe the best fix would be to surround this call with
ifdef-s or tune the Kconfig dependences, but I think that
marking this register function as __used is enough. No?
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix arp reply when received arp probe with sender ip 0.
Send arp reply with target ip address 0.0.0.0 and target hardware
address set to hardware address of requester. Previously sent reply
with target ip address and target hardware address set to same as
source fields.
Signed-off-by: Jonas Danielsson <the.sator@gmail.com>
Acked-by: Alexey Kuznetov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the bug, refcnt for md5sig pool was leaked when
an user try to delete a key if we have more than one key.
In addition to the leakage, we returned incorrect return
result value for userspace.
This fix should close Bug #9418, reported by <ming-baini@163.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
if (net_ratelimit())
IEEE80211_DEBUG_DROP(...)
can pollute the logs with messages like:
printk: 1 messages suppressed.
printk: 2 messages suppressed.
printk: 7 messages suppressed.
if debugging information is disabled. These messages are printed by
net_ratelimit(). Add a wrapper to net_ratelimit() that takes into account
the log level, so that net_ratelimit() is called only when we really want
to print something.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface with promisc/allmulti bit is taken down,
the mac80211 state can become confused. This fixes it by
making mac80211 keep track of all *active* interfaces that
have the promisc/allmulti bit set in the sdata, we sync
the interface bit into sdata at set_multicast_list() time
so this works.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I recently experienced unexplainable behaviour with the b43
driver when I had broken firmware uploaded. The cause may have
been that promisc mode was not correctly enabled or disabled
and this bug may have been the cause.
Note how the values are compared later in the function so
just doing the & will result in the wrong thing being
compared and the test being false almost always.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connection tracking entry (nf_conn) is about to copy itself it can
have some of its extension users (like nat) as being already freed and
thus not required to be copied.
Actually looking at this function I suspect it was copied from
nf_nat_setup_info() and thus bug was introduced.
Report and testing from David <david@unsolicited.net>.
[ Patrick McHardy states:
I now understand whats happening:
- new connection is allocated without helper
- connection is REDIRECTed to localhost
- nf_nat_setup_info adds NAT extension, but doesn't initialize it yet
- nf_conntrack_alter_reply performs a helper lookup based on the
new tuple, finds the SIP helper and allocates a helper extension,
causing reallocation because of too little space
- nf_nat_move_storage is called with the uninitialized nat extension
So your fix is entirely correct, thanks a lot :) ]
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64-bit systems sizeof(struct ifreq) is 8 bytes larger than
sizeof(struct iwreq).
For GET calls, the wireless extension code copies back into userspace
using sizeof(struct ifreq) but userspace and elsewhere only allocates
a "struct iwreq". Thus, this copy writes past the end of the iwreq
object and corrupts whatever sits after it in memory.
Fix the copy_to_user() length.
This particularly hurts the compat case because the wireless compat
code uses compat_alloc_userspace() and right after this allocated
buffer is the current bottom of the user stack, and that's what gets
overwritten by the copy_to_user() call.
Signed-off-by: David S. Miller <davem@davemloft.net>
The iucv is the only user of the various functions that are used to bring
parts of cpus up and down. Its the only allocpercpu user that will do
I/O on per cpu objects (which is difficult to do with virtually mapped memory).
And its the only use of allocpercpu where a GFP_DMA allocation is done.
Remove the allocpercpu calls from iucv and code the allocation and freeing
manually. After this patch it is possible to remove a large part of
the allocpercpu API.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
From: "Sam Jansen" <sjansen@google.com>
sysctl_tcp_congestion_control seems to have a bug that prevents it
from actually calling the tcp_set_default_congestion_control
function. This is not so apparent because it does not return an error
and generally the /proc interface is used to configure the default TCP
congestion control algorithm. This is present in 2.6.18 onwards and
probably earlier, though I have not inspected 2.6.15--2.6.17.
sysctl_tcp_congestion_control calls sysctl_string and expects a successful
return code of 0. In such a case it actually sets the congestion control
algorithm with tcp_set_default_congestion_control. Otherwise, it returns the
value returned by sysctl_string. This was correct in 2.6.14, as sysctl_string
returned 0 on success. However, sysctl_string was updated to return 1 on
success around about 2.6.15 and sysctl_tcp_congestion_control was not updated.
Even though sysctl_tcp_congestion_control returns 1, do_sysctl_strategy
converts this return code to '0', so the caller never notices the error.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the abstraction functions got added, conversion here was
made incorrectly. As a result, the skb may end up pointing
to skb which got included to the probe skb and then was freed.
For it to trigger, however, skb_transmit must fail sending as
well.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pktgen_output_ipsec() function can unlock this lock twice
due to merged error and plain paths. Remove one of the calls
to spin_unlock.
Other possible solution would be to place "return 0" right
after the first unlock, but at this place the err is known
to be 0, so these solutions are the same except for this one
makes the code shorter.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the remaining IPVS sysctl entries over to to use CTL_UNNUMBERED,
I stronly doubt that anyone is using the sys_sysctl interface to
these variables.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl table check failed: /net/ipv4/vs/lblc_expiration .3.5.21.19 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/lblcr_expiration .3.5.21.20 Missing strategy
Switch these entried over to use CTL_UNNUMBERED as clearly
the sys_syscal portion wasn't working.
This is along the same lines as Christian Borntraeger's patch that fixes
up entries with no stratergy in net/ipv4/ipvs/ip_vs_ctl.c
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running the latest git code I get the following messages during boot:
sysctl table check failed: /net/ipv4/vs/drop_entry .3.5.21.4 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/drop_packet .3.5.21.5 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/secure_tcp .3.5.21.6 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/sync_threshold .3.5.21.24 Missing strategy
I removed the binary sysctl handler for those messages and also removed
the definitions in ip_vs.h. The alternative would be to implement a
proper strategy handler, but syscall sysctl is deprecated.
There are other sysctl definitions that are commented out or work with
the default sysctl_data strategy. I did not touch these.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that stats of cpu 0 are counted twice, since
for_each_possible_cpu() is looping on all possible cpus, including 0
Before percpu conversion of ip_rt_acct, we should also remove the
assumption that CPU 0 is online (or even possible)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pipe messages start out life on a queue on the inode, but when first
read they're moved to the filp's private pointer. So it's possible for
a poll here to return null even though there's a partially read message
available.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Return an error from gss_import_sec_context_kerberos if the
negotiated context contains encryption or checksum types not
supported by the kernel code.
This fixes an Oops because success was assumed and later code found
no internal_ctx_id.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Instead of mapping all errors except EACCES to EAGAIN, map all errors
except EAGAIN to EACCES.
An example is user-land negotiating a Kerberos context with an encryption
type that is not supported by the kernel code. (This can happen due to
mis-configuration or a bug in the Kerberos code that does not honor our
request to limit the encryption types negotiated.) This failure is not
transient, and returning EAGAIN causes mount to continuously retry rather
than giving up.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Reported by Chuck Ebbert as:
https://bugzilla.redhat.com/show_bug.cgi?id=259501#c14
This routine is called each time hash should be replaced, nf_conn has
extension list which contains pointers to connection tracking users
(like nat, which is right now the only such user), so when replace takes
place it should copy own extensions. Loop above checks for own
extension, but tries to move higer-layer one, which can lead to above
oops.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should pass opt to the ->get/->set functions, not ops.
Tested-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The request_sock_queue's listen_opt is either vmalloc-ed or
kmalloc-ed depending on the number of table entries. Thus it
is expected to be handled properly on free, which is done in
the reqsk_queue_destroy().
However the error path in inet_csk_listen_start() calls
the lite version of reqsk_queue_destroy, called
__reqsk_queue_destroy, which calls the kfree unconditionally.
Fix this and move the __reqsk_queue_destroy into a .c file as
it looks too big to be inline.
As David also noticed, this is an error recovery path only,
so no locking is required and the lopt is known to be not NULL.
reqsk_queue_yank_listen_sk is also now only used in
net/core/request_sock.c so we should move it there too.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: rt_check_expire() can take a long time, add a cond_resched()
[ISDN] sc: Really, really fix warning
[ISDN] sc: Fix sndpkt to have the correct number of arguments
[TCP] FRTO: Clear frto_highmark only after process_frto that uses it
[NET]: Remove notifier block from chain when register_netdevice_notifier fails
[FS_ENET]: Fix module build.
[TCP]: Make sure write_queue_from does not begin with NULL ptr
[TCP]: Fix size calculation in sk_stream_alloc_pskb
[S2IO]: Fixed memory leak when MSI-X vector allocation fails
[BONDING]: Fix resource use after free
[SYSCTL]: Fix warning for token-ring from sysctl checker
[NET] random : secure_tcp_sequence_number should not assume CONFIG_KTIME_SCALAR
[IWLWIFI]: Not correctly dealing with hotunplug.
[TCP] FRTO: Plug potential LOST-bit leak
[TCP] FRTO: Limit snd_cwnd if TCP was application limited
[E1000]: Fix schedule while atomic when called from mii-tool.
[NETX]: Fix build failure added by 2.6.24 statistics cleanup.
[EP93xx_ETH]: Build fix after 2.6.24 NAPI changes.
[PKT_SCHED]: Check subqueue status before calling hard_start_xmit
Fix an obvious use-after-free spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes scanning for specific ssid's which is broken due to the
scan being queued up without respecting the ssid to scan for.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On commit 39c90ece75:
[IPV4]: Convert rt_check_expire() from softirq processing to workqueue.
we converted rt_check_expire() from softirq to workqueue, allowing the
function to perform all work it was supposed to do.
When the IP route cache is big, rt_check_expire() can take a long time
to run. (default settings : 20% of the hash table is scanned at each
invocation)
Adding cond_resched() helps giving cpu to higher priority tasks if
necessary.
Using a "if (need_resched())" test before calling "cond_resched();" is
necessary to avoid spending too much time doing the resched check.
(My tests gave a time reduction from 88 ms to 25 ms per
rt_check_expire() run on my i686 test machine)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I broke this in commit 3de96471bd:
[TCP]: Wrap-safed reordering detection FRTO check
tcp_process_frto should always see a valid frto_highmark. An invalid
frto_highmark (zero) is very likely what ultimately caused a seqno
compare in tcp_frto_enter_loss to do the wrong leading to the LOST-bit
leak.
Having LOST-bits integry ensured like done after commit
23aeeec365:
[TCP] FRTO: Plug potential LOST-bit leak
won't hurt. It may still be useful in some other, possibly legimate,
scenario.
Reported by Chazarain Guillaume <guichaz@yahoo.fr>.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fcc5a03ac4:
[NET]: Allow netdev REGISTER/CHANGENAME events to fail
makes the register_netdevice_notifier() handle the error from the
NETDEV_REGISTER event, sent to the registering block.
The bad news is that in this case the notifier block is
not removed from the list, but the error is returned to the
caller. In case the caller is in module init function and
handles this error this can abort the module loading. The
notifier block will be then removed from the kernel, but
will be left in the list. Oops :(
I think that the notifier block should be removed from the
chain in case of error, regardless whether this error is
handled by the caller or not. In the worst case (the error
is _not_ handled) module will not receive the events any
longer.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
NULL ptr can be returned from tcp_write_queue_head to cached_skb
and then assigned to skb if packets_out was zero. Without this,
system is vulnerable to a carefully crafted ACKs which obviously
is remotely triggerable.
Besides, there's very little that needs to be done in sacktag
if there weren't any packets outstanding, just skipping the rest
doesn't hurt.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It might be possible that, in some extreme scenario that
I just cannot now construct in my mind, end_seq <=
frto_highmark check does not match causing the lost_out
and LOST bits become out-of-sync due to clearing and
recounting in the loop.
This may fix LOST-bit leak reported by Chazarain Guillaume
<guichaz@yahoo.fr>.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise TCP might violate packet ordering principles that FRTO
is based on. If conventional recovery path is chosen, this won't
be significant at all. In practice, any small enough value will
be sufficient to provide proper operation for FRTO, yet other
users of snd_cwnd might benefit from a "close enough" value.
FRTO's formula is now equal to what tcp_enter_cwr() uses.
FRTO used to check application limitedness a bit differently but
I changed that in commit 575ee7140d
and as a result checking for application limitedness became
completely non-existing.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only qdiscs that check subqueue state before dequeue'ing are PRIO
and RR. The other qdiscs, including the default pfifo_fast qdisc,
will allow traffic bound for subqueue 0 through to hard_start_xmit.
The check for netif_queue_stopped() is done above in pkt_sched.h, so
it is unnecessary for qdisc_restart(). However, if the underlying
driver is multiqueue capable, and only sets queue states on subqueues,
this will allow packets to enter the driver when it's currently unable
to process packets, resulting in expensive requeues and driver
entries. This patch re-adds the check for the subqueue status before
calling hard_start_xmit, so we can try and avoid the driver entry when
the queues are stopped.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not correct to assume one can get nsec from a ktime directly by
using .tv64 field.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts Eric's commit 2b008b0a8e
It diets .text & .data section of the kernel if CONFIG_NET_NS is not set.
This is safe after list operations cleanup.
Signed-of-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NET_NS is not set, the only namespace is possible.
This patch removes list of pernet_operations and cleanups code a bit.
This list is not needed if there are no namespaces. We should just call
->init method.
Additionally, the ->exit will be called on module unloading only. This
case is safe - the code is not discarded. For the in/kernel code, ->exit
should never be called.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets routed between bridges have the POST_ROUTING hook invoked
twice since bridging mistakes them for bridged packets because
they have skb->nf_bridge set.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both lookup the nf_sockopt_ops object to call the get/set callbacks
from, but they perform it in a completely similar way.
Introduce the helper for finding the ops.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size passing to memset is the size of a pointer.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inetpeer.c tracks the LRU list of inet_perr-s, but makes
it by hands. Use the list_head-s for this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the following unused EXPORT_SYMBOL's:
- ip_vs_try_bind_dest
- ip_vs_find_dest
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify some code by eliminating duplicate if-else clauses in
packet_do_bind().
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
...and fix a couple of bugs in the NBD, CIFS and OCFS2 socket handlers.
Looking at the sock->op->shutdown() handlers, it looks as if all of them
take a SHUT_RD/SHUT_WR/SHUT_RDWR argument instead of the
RCV_SHUTDOWN/SEND_SHUTDOWN arguments.
Add a helper, and then define the SHUT_* enum to ensure that kernel users
of shutdown() don't get confused.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Mark Fasheh <mark.fasheh@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userland neighbor discovery options are typically heavily involved with
the interface on which thay are received: add a missing ifindex field to
the original struct. Thanks to Rmi Denis-Courmont.
Signed-off-by: Pierre Ynard <linkfanel@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In net/sctp/sm_statefuns.c::sctp_sf_abort_violation() we may leak
the storage allocated for 'abort' by returning from the function
without using or freeing it. This happens in case
"sctp_auth_recv_cid(SCTP_CID_ABORT, asoc)" is true and we jump to
the 'discard' label.
Spotted by the Coverity checker.
The simple fix is to simply move the creation of the "abort chunk"
to after the possible jump to the 'discard' label. This way we don't
even have to allocate the memory at all in the problem case.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch fixes a small memory leak. Default fib rules can be deleted by
the user if the rule does not carry FIB_RULE_PERMANENT flag, f.e. by
ip rule flush
Such a rule will not be freed as the ref-counter has 2 on start and becomes
clearly unreachable after removal.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
* it already statically initialized
* reinitializing live global spinlock every time netns is
setup is also wrong
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unix_nr_socks value is limited with the 2 * get_max_files() value,
as seen from the unix_create1(). However, the check and the actual
increment are separated with the GFP_KERNEL allocation, so this limit
can be exceeded under a memory pressure - task may go to sleep freeing
the pages and some other task will be allowed to allocate a new sock
and so on and so forth.
So make the increment before the check (similar thing is done in the
sock_kmalloc) and go to kmalloc after this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scan_inflight() routine scans through the unix sockets and calls
some passed callback. The fact is that all these callbacks work with
the unix_sock objects, not the sock ones, so make this conversion in
the scan_inflight() before calling the callbacks.
This removes one unneeded variable from the inc_inflight_move_tail().
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter is _always_ modified under the unix_gc_lock spinlock,
so its atomicity can be provided w/o additional efforts.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket option for packet sockets to return the original ifindex instead
of the bonded ifindex will not match multicast traffic. Since this socket
option is the most useful for layer 2 traffic and multicast traffic, make
the option multicast-aware.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I meant for this to be selectable only with EMBEDDED, not enabled only
with EMBEDDED. This does it that way. Sorry.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make "decrypt failed" and "have no key" debugging messages compile
conditionally upon CONFIG_MAC80211_DEBUG. They have been useful for
finding certain problems in the past, but in many cases they just
clutter a user's logs.
A typical example is an enviornment where multiple SSIDs are using a
single BSSID but with different protection schemes or different keys
for each SSID. In such an environment these messages are just noise.
Let's just leave them for those interested enough to turn-on debugging.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the long bug-hunt for why dynamic WEP networks didn't work it
turned out that mac80211 incorrectly uses IW_AUTH_KEY_MGMT while
it should use IW_AUTH_PRIVACY_INVOKED to determine whether to
associate to protected networks or not.
This patch changes the behaviour to be that way and clarifies the
existing code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver operations set_ieee8021x(), set_port_auth() and
set_privacy_invoked() are not used by any drivers, except
set_privacy_invoked() they aren't even used by mac80211.
Remove them at least until we need to support drivers with
mac80211 that require getting this information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Robert pointed out that I missed this file when removing the management
interface. Do it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace mutex_lock_interruptible() by mutex_lock() in rfkill_register(),
as interruptible doesn't make sense there.
Add a sanity check for rfkill->type, as that's used for an unchecked dereference
in an array and might cause hard to debug crashes if the driver sets this
to an invalid value.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows a driver to ask for a specific rate control algorithm.
The rate control algorithm asked for must be registered and be
available as a module or built-in.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, mac80211 would allow registering the same rate control
algorithm twice. This is a programming error in the registration
and should not happen; additionally the second version could never
be selected. Disallow this and warn about it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must use subsys_initcall, because we must initialize before a
driver calls rfkill_register().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Too frequently people do not have module autoloading enabled
or fail to install the rate control module correctly, hence
their hardware probing fails due to no rate control algorithm
being available. This makes the 'simple' algorithm built into
the mac80211 module unless EMBEDDED is enabled in which case
it can be disabled (eg. if the wanted driver requires another
rate control algorithm.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Registering the switch triggers a LED event, so we must register
LED triggers before the switch.
This has a potential to fix a crash, depending on how the device
driver initializes the rfkill data structure.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MLME request reason code is host-endian and our passing
it to the low level functions is host-endian as well since
they do the swapping. I noticed that the reason code 768 was
sent (0x300) rather than 3 when wpa_supplicant terminates.
This removes the superfluous cpu_to_le16() call.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Computing the rank of the first set bit in the hash mask (for using later
in u32_hash_fold()) was done with plain C code. Using ffs() instead makes
the code more readable and improves performance (since ffs() is better
optimized in assembler).
Using the conditional operator on hash mask before applying ntohl() also
saves one ntohl() call if mask is 0.
Signed-off-by: Radu Rendec <radu.rendec@ines.ro>
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the VLAN device is down, the unicast addresses are not configured
on the underlying device, so we shouldn't attempt to sync them.
Noticed by Dmitry Butskoy <buc@odusz.so-cdu.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both check for the family to select an appropriate tunnel list.
Consolidate this check and make the for() loop more readable.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tunnel64_protocol uses the tunnel4_protocol's err_handler and
thus calls the tunnel4_protocol's handlers.
This is not very good, as in case of (icmp) error the wrong error
handlers will be called (e.g. ipip ones instead of sit) and this
won't be noticed at all, because the error is not reported.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like in the af_packet.c, the ipx_sock_nr variable is used
for debugging purposes.
Switch to using existing infrastructure. Thanks to Arnaldo for
pointing this out.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet_socks_nr variable is used purely for debugging
the number of sockets.
As Arnaldo pointed out, there's already an infrastructure
for this purposes, so switch to using it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many places that get the dst entry, increase the
__use counter and set the "lastuse" time stamp.
Make a helper for this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both places look like
if (err == XXX)
goto yyy;
done:
while both yyy targets look like
err = XXX;
goto done;
so this is ok to remove the above if-s.
yyy labels are used in other places and are not removed.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we run out of mem when fragmenting, the clearing of
FLAG_ONLY_ORIG_SACKED might get missed which then feeds FRTO
with false information. Move clearing outside skb processing
loop so that it will get executed even if the skb loop
terminates prematurely due to out-of-mem.
Besides, now the core of the loop truly deals with a single
skb only, which also enables creation a more self-contained
of tcp_sacktag_one later on.
In addition, small reorganization of if branches was made.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes subtle bug like the one with fastpath_cnt_hint happening
due to the way the GSO and hints interact. Because hints are not
reset when just a GSOed skb is partially ACKed, there's no
guarantee that the relevant part of the write queue is going to
be processed in sacktag at all (skbs below snd_una) because
fastpath hint can fast forward the entrypoint.
This was also on the way of future reductions in sacktag's skb
processing. Also future cleanups in sacktag can be made after
this (in 2.6.25).
This may make reordering update in tcp_try_undo_partial
redundant but I'm not too sure so I left it there.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reordering detection fails to take account that the reordered
skb may have pcount larger than 1. In such case the lowest of
them had the largest reordering, the old formula used the
highest of them which is pcount - 1 packets less reordered.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the code calls uncork, trigger a queue flush, even
if the queue was not corked. Most callers that explicitely
cork the queue will have additinal checks to see if they
corked it. Callers who do not cork the queue expect packets
to flow when they call uncork.
The scneario that showcased this bug happend when we were not
able to bundle DATA with outgoing COOKIE-ECHO. As a result
the data just sat in the outqueue and did not get transmitted.
The application expected a response, but nothing happened.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
There is a small bug when we process a FWD-TSN. We'll deliver
anything upto the current next expected SSN. However, if the
next expected is already in the queue, it will take another
chunk to trigger its delivery. The fix is to simply check
the current queued SSN is the next expected one.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
SCTP-AUTH and future ADD-IP updates have a requirement to
do additional verification of parameters and an ability to
ABORT the association if verification fails. So, introduce
additional return code so that we can clear signal a required
action.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
A SCTP endpoint may have a lot of associations on them and walking
the list is fairly inefficient. Instead, use a hashed lookup,
and filter out the hash list based on the endopoing we already have.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
There is a possible race condition where the timer code will
free the association and the next packet in the queue will also
attempt to free the same association.
The example is, when we receive an ABORT at about the same time
as the retransmission timer fires. If the timer wins the race,
it will free the association. Once it releases the lock, the
queue processing will recieve the ABORT and will try to free
the association again.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch adds a tunable that will allow ADD_IP to work without
AUTH for backward compatibility. The default value is off since
the default value for ADD_IP is off as well. People who need
to use ADD-IP with older implementations take risks of connection
hijacking and should consider upgrading or turning this tunable on.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
After learning more about rcu, it looks like the ADD-IP hadling
doesn't need to call call_rcu_bh. All the rcu critical sections
use rcu_read_lock, so using call_rcu_bh is wrong here.
Now, restore the local_bh_disable() code blocks and use normal
call_rcu() calls. Also restore the missing return statement.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Commit d0ce92910b broke several retransmit
cases including fast retransmit. The reason is that we should
only delay by rto while doing retranmists as a result of a timeout.
Retransmit as a result of path mtu discover, fast retransmit, or
other evernts that should trigger immidiate retransmissions got broken.
Also, since rto is doubled prior to marking of packets elegable for
retransmission, we never marked correct chunks anyway.
The fix is provide a reason for a given retransmission so that we
can mark chunks appropriately and to save the old rto value to do
comparisons against.
All regressions tests passed with this code.
Spotted by Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
If ASCONF chunk is bundled with other chunks as the first chunk, when
process the ASCONF parameters, full packet data will be process as the
parameters of the ASCONF chunk, not only the real parameters. So if you
send a ASCONF chunk bundled with other chunks, you will get an unexpect
result.
This problem also exists when ASCONF-ACK chunk is bundled with other chunks.
This patch fix this problem.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Just fix the bad format of the comment in outqueue.c.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Commit ed6dcf4a in the history.git tree broke netlink_unicast timeouts
by moving the schedule_timeout() call to a new function that doesn't
propagate the remaining timeout back to the caller. This means on each
retry we start with the full timeout again.
ipc/mqueue.c seems to actually want to wait indefinitely so this
behaviour is retained.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As done two years ago on IP route cache table (commit
22c047ccbc) , we can avoid using one
lock per hash bucket for the huge TCP/DCCP hash tables.
On a typical x86_64 platform, this saves about 2MB or 4MB of ram, for
litle performance differences. (we hit a different cache line for the
rwlock, but then the bucket cache line have a better sharing factor
among cpus, since we dirty it less often). For netstat or ss commands
that want a full scan of hash table, we perform fewer memory accesses.
Using a 'small' table of hashed rwlocks should be more than enough to
provide correct SMP concurrency between different buckets, without
using too much memory. Sizing of this table depends on
num_possible_cpus() and various CONFIG settings.
This patch provides some locking abstraction that may ease a future
work using a different model for TCP/DCCP table.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the master daemon to sync the connection when it is about
to close. This makes the connections on the backup to close or timeout
according their state. Before the sync was performed only if the
connection is in ESTABLISHED state which always made the connections to
timeout in the hard coded 3 minutes. However the Andy Gospodarek's patch
([IPVS]: use proper timeout instead of fixed value) effectively did nothing
more than increasing this to 15 minutes (Established state timeout). So
this patch makes use of proper timeout since it syncs the connections on
status changes to FIN_WAIT (2min timeout) and CLOSE (10sec timeout).
However if the backup misses CLOSE hopefully it did not miss FIN_WAIT.
Otherwise we will just have to wait for the ESTABLISHED state timeout. As
it is without this patch. This way the number of the hanging connections
on the backup is kept to minimum. And very few of them will be left to
timeout with a long timeout.
This is important if we want to make use of the fix for the real server
overcommit on master/backup fail-over.
Signed-off-by: Rumen G. Bogdanovski <rumen@voicecho.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem with node overload on director fail-over.
Given the scenario: 2 nodes each accepting 3 connections at a time and 2
directors, director failover occurs when the nodes are fully loaded (6
connections to the cluster) in this case the new director will assign
another 6 connections to the cluster, If the same real servers exist
there.
The problem turned to be in not binding the inherited connections to
the real servers (destinations) on the backup director. Therefore:
"ipvsadm -l" reports 0 connections:
root@test2:~# ipvsadm -l
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP test2.local:5999 wlc
-> node473.local:5999 Route 1000 0 0
-> node484.local:5999 Route 1000 0 0
while "ipvs -lnc" is right
root@test2:~# ipvsadm -lnc
IPVS connection entries
pro expire state source virtual destination
TCP 14:56 ESTABLISHED 192.168.0.10:39164 192.168.0.222:5999
192.168.0.51:5999
TCP 14:59 ESTABLISHED 192.168.0.10:39165 192.168.0.222:5999
192.168.0.52:5999
So the patch I am sending fixes the problem by binding the received
connections to the appropriate service on the backup director, if it
exists, else the connection will be handled the old way. So if the
master and the backup directors are synchronized in terms of real
services there will be no problem with server over-committing since
new connections will not be created on the nonexistent real services
on the backup. However if the service is created later on the backup,
the binding will be performed when the next connection update is
received. With this patch the inherited connections will show as
inactive on the backup:
root@test2:~# ipvsadm -l
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP test2.local:5999 wlc
-> node473.local:5999 Route 1000 0 1
-> node484.local:5999 Route 1000 0 1
rumen@test2:~$ cat /proc/net/ip_vs
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP C0A800DE:176F wlc
-> C0A80033:176F Route 1000 0 1
-> C0A80032:176F Route 1000 0 1
Regards,
Rumen Bogdanovski
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Rumen G. Bogdanovski <rumen@voicecho.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
The struct proto has the per-cpu "inuse" counter, which is handled
with a special care. All the handling code hides under the ifdef
CONFIG_SMP and it introduces some code duplication and makes it
look worse than it could.
Clean this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function crypto_alloc_comp returns an errno instead of NULL
to indicate error. So it needs to be tested with IS_ERR.
This is based on a patch by Vicen Beltran Querol.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on report and patch by Doug Kehn <rdkehn@yahoo.com>:
vconfig returns the following error when attempting to execute the
set_ingress_map command:
vconfig: socket or ioctl error for set_ingress_map: Operation not permitted
In vlan.c, vlan_ioctl_handler for SET_VLAN_INGRESS_PRIORITY_CMD
sets err = -EPERM and calls vlan_dev_set_ingress_priority.
vlan_dev_set_ingress_priority is a void function so err remains
at -EPERM and results in the vconfig error (even though the ingress
map was set).
Fix by setting err = 0 after the vlan_dev_set_ingress_priority call.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because net_free is called by copy_net_ns before its declaration, the
compiler gives an error. This patch puts net_free before copy_net_ns
to fix this.
The compiler error:
net/core/net_namespace.c: In function 'copy_net_ns':
net/core/net_namespace.c:97: error: implicit declaration of function 'net_free'
net/core/net_namespace.c: At top level:
net/core/net_namespace.c:104: warning: conflicting types for 'net_free'
net/core/net_namespace.c:104: error: static declaration of 'net_free' follows non-static declaration
net/core/net_namespace.c:97: error: previous implicit declaration of 'net_free' was here
The error was introduced by the '[NET]: Hide the dead code in the
net_namespace.c' patch (6a1a3b9f68).
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While trying to implement u32 hashes in my shaping machine I ran into
a possible bug in the u32 hash/bucket computing algorithm
(net/sched/cls_u32.c).
The problem occurs only with hash masks that extend over the octet
boundary, on little endian machines (where htonl() actually does
something).
Let's say that I would like to use 0x3fc0 as the hash mask. This means
8 contiguous "1" bits starting at b6. With such a mask, the expected
(and logical) behavior is to hash any address in, for instance,
192.168.0.0/26 in bucket 0, then any address in 192.168.0.64/26 in
bucket 1, then 192.168.0.128/26 in bucket 2 and so on.
This is exactly what would happen on a big endian machine, but on
little endian machines, what would actually happen with current
implementation is 0x3fc0 being reversed (into 0xc03f0000) by htonl()
in the userspace tool and then applied to 192.168.x.x in the u32
classifier. When shifting right by 16 bits (rank of first "1" bit in
the reversed mask) and applying the divisor mask (0xff for divisor
256), what would actually remain is 0x3f applied on the "168" octet of
the address.
One could say is this can be easily worked around by taking endianness
into account in userspace and supplying an appropriate mask (0xfc03)
that would be turned into contiguous "1" bits when reversed
(0x03fc0000). But the actual problem is the network address (inside
the packet) not being converted to host order, but used as a
host-order value when computing the bucket.
Let's say the network address is written as n31 n30 ... n0, with n0
being the least significant bit. When used directly (without any
conversion) on a little endian machine, it becomes n7 ... n0 n8 ..n15
etc in the machine's registers. Thus bits n7 and n8 would no longer be
adjacent and 192.168.64.0/26 and 192.168.128.0/26 would no longer be
consecutive.
The fix is to apply ntohl() on the hmask before computing fshift,
and in u32_hash_fold() convert the packet data to host order before
shifting down by fshift.
With helpful feedback from Jamal Hadi Salim and Jarek Poplawski.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are places that check for CONFIG_IP_MULTIPLE_TABLES
twice in the same file, but the internals of these #ifdefs
can be merged.
As a side effect - remove one ifdef from inside a function.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes last proc_net_create() user. Kudos to Benjamin Thery and
Stephen Hemminger for comments on previous version.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
tecl_reset() is called from deactivate and qdisc is set to noop already,
but subsequent teql_xmit does not know about it and dereference private
data as teql qdisc and thus oopses.
not catch it first :)
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial patch to make "sctcp,sctpv6" protocols uses the fast "inuse
sockets" infrastructure
Each protocol use then a static percpu var, instead of a dynamic one.
This saves some ram and some cpu cycles
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial patch to make "tcpv6,udpv6,udplitev6,rawv6" protocols uses the
fast "inuse sockets" infrastructure
Each protocol use then a static percpu var, instead of a dynamic one.
This saves some ram and some cpu cycles
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial patch to make "tcp,udp,udplite,raw" protocols uses the fast
"inuse sockets" infrastructure
Each protocol use then a static percpu var, instead of a dynamic one.
This saves some ram and some cpu cycles
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"struct proto" currently uses an array stats[NR_CPUS] to track change on
'inuse' sockets per protocol.
If NR_CPUS is big, this means we use a big memory area for this.
Moreover, all this memory area is located on a single node on NUMA
machines, increasing memory pressure on the boot node.
In this patch, I tried to :
- Keep a fast !CONFIG_SMP implementation
- Keep a fast CONFIG_SMP implementation for often used protocols
(tcp,udp,raw,...)
- Introduce a NUMA efficient implementation
Some helper macros are defined in include/net/sock.h
These macros take into account CONFIG_SMP
If a "struct proto" is declared without using DEFINE_PROTO_INUSE /
REF_PROTO_INUSE
macros, it will automatically use a default implementation, using a
dynamically allocated percpu zone.
This default implementation will be NUMA efficient, but might use 32/64
bytes per possible cpu
because of current alloc_percpu() implementation.
However it still should be better than previous implementation based on
stats[NR_CPUS] field.
When a "struct proto" is changed to use the new macros, we use a single
static "int" percpu variable,
lowering the memory and cpu costs, still preserving NUMA efficiency.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The #idfed CONFIG_IP_MROUTE is sometimes places inside the if-s,
which looks completely bad. Similar ifdefs inside the functions
looks a bit better, but they are also not recommended to be used.
Provide an ifdef-ed ip_mroute_opt() helper to cleanup the code.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the checksum verification is postponed till user calls recv or poll,
the inrementation of Udp6InErrors counter should be also postponed.
Currently, it is postponed in non-blocking operation case. However it
should be postponed in all case like the IPv4 code.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_push_pending_frames and ip6_flush_pending_frames do the
same things to flush the sock's cork. Move this into a separate
function and save ~100 bytes from the .text
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip_push_pending_frames and ip_flush_pending_frames do the
same things to flush the sock's cork. Move this into a separate
function and save ~80 bytes from the .text
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix --arp-gratuitous matching dependence on --arp-ip-{src,dst}
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Lutz Preler <Lutz.Pressler@SerNet.DE>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code is using knowledge that nf_sockopt_ops::list list_head is first
field in structure by using casts. Switch to list_for_each_entry()
itetators while I am at it.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Paul McKenney, the rcu_dereference calls in the init path
of NAT modules are unneeded, remove them.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sort matches and targets in the NF makefiles.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transfer all my copyright over to our company.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I plan to kill ->get_info which means killing proc_net_create().
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list of options that the fd transport accepts is missing end-of-options
marker. This patch adds it.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
v9fs_match_trans function returns arbitrary transport module instead of NULL
when the requested transport is not registered. This patch modifies the
function to return NULL in that case.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
sg_mark_end() overwrites the page_link information, but all users want
__sg_mark_end() behaviour where we just set the end bit. That is the most
natural way to use the sg list, since you'll fill it in and then mark the
end point.
So change sg_mark_end() to only set the termination bit. Add a sg_magic
debug check as well, and clear a chain pointer if it is set.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Documentation updates for network interfaces.
1. Add doc for netif_napi_add
2. Remove doc for unused returns from netif_rx
3. Add doc for netif_receive_skb
[ Incorporated minor mods from Randy Dunlap -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cache is only required to create new namespaces,
but we won't have them in CONFIG_NET_NS=n case.
Hide it under the appropriate ifdef.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_net is called for the init net namespace
only (int the CONFIG_NET_NS=n of course) from the __init
function, so mark it as __net_init to disappear with the
caller after the boot.
Yet again, in the perfect world this has to be under
#ifdef CONFIG_NET_NS, but it isn't guaranteed that every
subsystem is registered *after* the init_net_ns is set
up. After we are sure, that we don't start registering
them before the init net setup, we'll be able to move
this code under the ifdef.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The namespace creation/destruction code is never called
if the CONFIG_NET_NS is n, so it's OK to move it under
appropriate ifdef.
The copy_net_ns() in the "n" case checks for flags and
returns -EINVAL when new net ns is requested. In a perfect
world this stub must be in net_namespace.h, but this
function need to know the CLONE_NEWNET value and thus
requires sched.h. On the other hand this header is to be
injected into almost every .c file in the networking code,
and making all this code depend on the sched.h is a
suicidal attempt.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the new pernet something (subsys, device or operations) is
being registered, the init callback is to be called for each
namespace, that currently exitst in the system. During the
unregister, the same is to be done with the exit callback.
However, not every pernet something has both calls, but the
check for the appropriate pointer to be not NULL is performed
inside the for_each_net() loop.
This is (at least) strange, so tune this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, the zero_it argument can be completely removed from
the callers and from the function prototype.
Besides, fix the checkpatch.pl warnings about using the
assignments inside if-s.
This patch is rather big, and it is a part of the previous one.
I splitted it wishing to make the patches more readable. Hope
this particular split helped.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
