We often have the situation that we register a subchannel and start device
recognition, only to find out that the device is not usable after all, which
triggers an unregister of the subchannel. This often happens on hundreds of
subchannels on a LPAR, leading to a storm of events which aren't of any use.
Therefore, use uevent_suppress to delay the KOBJ_ADD uevent for a subchannel
until we know that its ccw_device is to be registered.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Eric Rannaud <eric.rannaud@gmail.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We used to unregister ccw devices not directly from the I/O
subchannel remove function in order to avoid lifelocks on the
css bus semaphore. This semaphore is gone, and there is no reason
to not unregister the ccw device directly (it is even better since
it is more in keeping with the goal of immediate disconnect).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We allocage two pages when channel path measurements are enabled
via cm_enable. We must not forget to free them again when
channel path measurements are disabled again.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a mutex for struct ccwgroup to prevent simuntaneous
register/unregister on the same ccwgroup device.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure that channel-path related subchannel data is only retrieved and
used when it is valid and that it is updated when it may have changed.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use a bitmap for indicating which subchannels require evaluation
instead of allocating memory for each evaluation request. This
approach reduces memory consumption during recovery in case of
massive evaluation request occurrence and removes the need for
memory allocation failure handling.
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Path verification triggered by changes to the available CHPIDs will be
interrupted by another change but not re-started. This results in an
invalid path mask.
To solve this make sure to completely re-start path verification when
changing the available paths.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert ccw_uevent to use add_uevent_var and adapt snprint_alias.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a new attribute to the channel-path sysfs directory through which
channel-path configure operations can be triggered. Also listen for
hardware events requesting channel-path configure operations and
process them accordingly.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Detangle the online_store code and make it more readable.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Check validity flag of CHPID description data before continuing with
channel-path initialization.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Channel path status can now be modified by writing '0' and '1'
to the sysfs status attribute in addition to 'offline' and
'online' respectively.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Introduce data type for channel-path IDs.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Clean interface between cio and ipl code, so Peter stops complaining.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Wipe internal irb if the clear function bit is set before accumulating
bits from the irb in order to follow hardware behaviour.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Only accumulate device status field in irb if it is valid.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Make sure set_slsb problems are handled correctly in
qdio_do_qdio_fill_input() and qdio_do_qdio_fill_output.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch (as868) adds a helper routine for device drivers that need
to set up a callback to perform some action in a different process's
context. This is intended for use by attribute methods that want to
unregister themselves or their parent device. Attribute method calls
are mutually exclusive with unregistration, so such actions cannot be
taken directly.
Two attribute methods are converted to use the new helper routine: one
for SCSI device deletion and one for System/390 ccwgroup devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The subchannel may just be status pending, even with actl == 0. We
must go through the cancel_halt_clear procedure to put the subchannel
into a defined state.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After I/O has been killed by the common I/O layer, trigger path
verification which will queue cio_device_nopath_notify itself if it
finds a device to be without paths.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure we hold the device lock when we modify the ccw device
structure but always call the notify function without the lock held.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With CONFIG_SHARED_KERNEL the kernel text segment that might be in a
read only memory sections starts at 1MB. Memory between 0x12000 and
0x100000 is unused then. Free this, so we have appr. an extra MB
of memory available.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setup.h has been misused for ipl related stuff in the past. We now move
everything, which has to do with ipl and reipl to a new header file named
"ipl.h".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] remove __io_virt and mmiowb.
[S390] cio: use ARRAY_SIZE in device_id.c
[S390] cio: Fixup interface for setting options on ccw devices.
[S390] smp_call_function/smp_call_function_on locking.
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current ccw_device_set_options() sets a specified mask of options
and clears those not specified, but there is no way to find out which
options have already been set.
In order to fix this up, introduce the following interface changes:
ccw_device_set_options() now only sets the specified bits, but does
not clear those that are not specified.
ccw_device_clear_options() clears the specified bits.
ccw_device_set_options_mask() provides the old semantics (setting only
the specified bits and clearing the others).
Device drivers now work as expected. qdio has been adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Hopefully this will make it more maintainable and less error prone.
Code makes use of search_exception_tables(). Since it calls this
function before the kernel exeception table is sorted, there is an
early call to sort_main_extable().
This way it's easy to use the already present infrastructure of fixup
sections. Also this would allows to easily convert the rest of
head[31|64].S into C code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds support for clock synchronization to an external time
reference (ETR). The external time reference sends an oscillator
signal and a synchronization signal every 2^20 microseconds to keep
the TOD clocks of all connected servers in sync. For availability
two ETR units can be connected to a machine. If the clock deviates
for more than the sync-check tolerance all cpus get a machine check
that indicates that the clock is out of sync. For the lovely details
how to get the clock back in sync see the code below.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lower priority of "Blacklisted device detected" messages so we don't
overwrite more useful messages.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change CHSC event handling to be more easily extensible.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we have a subchannel id which has been generated via
for_each_subchannel(), it might contain an invalid subchannel set id.
We need to catch the ensuing operand exception by using stsch_err()
instead of stsch() in all possible cases.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Create/remove the channel measurement binary files with
device_{create,remove}_bin_file instead of sysfs_{create,remove}_bin_file.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we try to start path verification when an unsolicited interrupt
is already pending, stctl shows status pending and we delay path
verification again. We need to check for the doverify bit when the
unsolicited interrupt comes in and then do path verification.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since ssd_info is now available before the subchannel is registered,
we don't need to check whether it is available.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use barrier() in stsch_reset() instead of duplicating the stsch()
inline assembly and adding "memory" to the clobberlist.
Pointed out by Chuck Ebbert.
Real fix would be to add a fixup section to the stsch() and extend the
basic program check handler so it searches the exception tables in case
of a program check.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Copy inline assembly of stsch and add "memory" to clobber list in order
to prevent gcc from optimizing away the checking of the global variable
"pgm_check_occured".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Asynchronous probe can release memory of a subchannel before
css_get_ssd_info is called. To fix this call css_get_ssd_info
before registering with driver core.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reboot hangs on LPARs without diag308 support. The reason for this is,
that before the reboot is done, the channel subsystem is shut down.
During the reset on each possible subchannel a "store subchannel" is
done. This operation can end in a program check interruption, if the
specified subchannel set is not implemented by the hardware. During
the reset, currently we do not have a program check handler, which
leads to the described kernel bug. We install now a new program check
handler for the reboot code to fix this problem.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A HiperSocket multicast queue works asynchronously. When sending
buffers, the buffer state change from PRIMED to EMPTY may happen
delayed. Reschedule the checking for changes in the outbound queue,
if there are still PRIMED buffers.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- create a 'pseudo_subchannel' per channel subsystem (the 'orphanage')
- use the orphanage as a shelter for ccw_devices that can't remain on the same
subchannel
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert the subchannel lock to a pointer to a lock. Needed for the dynamic
subchannel mapping patch.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove CONFIG_QETH_PERF_STATS and use a sysfs attribute instead.
We want to have the ability to turn the statistics on/off at runtime.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In io_subchannel_register(), it is better to just reprobe the current
device if it hasn't a driver yet than to rescan the whole bus.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If I/O was running on a just varied off chpid, it will be terminated.
If this was a common I/O layer internal I/O, it needs to be retried.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the last path to a device is gone after a chpid has been varied
off, putting it on the slow queue doesn't prevent a device driver
from still attempting to use it (it may stay on the slow queue for a
long time). Instead, trigger a verify event which will prevent I/O
attempts from the device driver immediately.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add some prefixes to constands defined in drivers/s390/net/qdio.h
and drivers/s390/lcs.h to make it possible to include the three
header files drivers/s390/net/qeth.h, drivers/s390/net/qdio.h and
drivers/net/s390/lcs.h in one C file. This is required for the
patch that generates the kerntypes.o file for use by lcrash.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of re-IPL and diag308 doesn't work we have to reset all devices
manually and wait synchronously that each reset finished.
This patch adds the necessary infrastucture and the first exploiter of it.
Subsystems that need to add a function that needs to be called at re-IPL
may register/unregister this function via
struct reset_call {
struct reset_call *next;
void (*fn)(void);
};
void register_reset_call(struct reset_call *reset);
void unregister_reset_call(struct reset_call *reset);
When the registered function get called the context is:
- all cpus beside the current one are stopped
- all machine checks and interrupts are disabled
- prefixing is disabled
- a default machine check handler is available for use
The registered functions may not take any locks are sleep.
For the common I/O layer part of this patch:
Introduce a reset_call css_reset that does the following:
- clear all subchannels
- perform a rchp on all channel paths and wait for the resulting
machine checks
This replaces the calls to clear_all_subchannels() and
cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now
uses reipl_find_schid() to determine the subchannel id for a given
device id.
Also remove cio_reset_channel_paths() and friends since they are not
needed anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ccw_device_register() is only called from io_subchannel_register()
and io_subchannel_probe() and will never be called for possible
non-io subchannels.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move css_probe_device() behind giving up the lock for the old subchannel
in css_evaluate_known_subchannel() so we aren't disabled when we call it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reset device operational notification flag when channel paths become
unavailable during path verification.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The grace period handling introduced needless complexity. It didn't
help the dasd driver (which can handle terminated I/O just well),
and it doesn't help for long running channel programs (which won't
complete during the grace period anyway). Terminating I/O using a
path that just disappeared immediately is much more consistent with
what the user expects.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the proper structures to identify device and subchannel. Change
get_disc_ccwdev_by_devno() to get_disc_ccwdev_by_dev_id().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the last few places where a pointer to pt_regs gets passed.
Also make sure we call set_irq_regs() before irq_enter() and after
irq_exit(). This doesn't fix anything but makes sure s390 looks the
same like all other architectures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In order to determine chpid validity, we need to check whether the
corresponding path is specified in the pim.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Retry internal operation after unit check instead of aborting them.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add timeout handler for common-I/O-layer-internal I/O operations.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
While the machine owns us an interrupt in these cases (and we should get
one), reality isn't always like that...
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Major cleanup of all s390 inline assemblies. They now have a common
coding style. Quite a few have been shortened, mainly by using register
asm variables. Use of the EX_TABLE macro helps as well. The atomic ops,
bit ops and locking inlines new use the Q-constraint if a newer gcc
is used. That results in slightly better code.
Thanks to Christian Borntraeger for proof reading the changes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
css_evaluate_subchannel() operates subchannel without lock which can
lead to erratic behavior caused by concurrent device access. Also
split evaluation function to make it more readable.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reappearing channel paths are sometimes not utilized by CCW devices
because path verification incorrectly relies on path-operational-mask
information which is not updated until a channel path has been used
again.
Modify path verification procedure to always query all available paths
to a device.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CHPIDs that are logically varied off will not be removed from
a CCW device's path group because resign-from-pathgroup command is
issued with invalid path mask of 0 because internal CCW operations
are masked by the logical path mask after the relevant bits are
cleared by the vary operation.
Do not apply logical path mask to internal operations.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Subchannel may incorrectly remain in state no-path after channel paths
have reappeared. Currently the scan for subchannels which are using a
channel path ends at the first occurrence if a full link address was
provided by the channel subsystem. The scan needs to continue over
all subchannels.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add the MODALIAS environment variable for ccw bus uevents.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The last SLSB has to be set to STATE_PROCESSING if we really want to
use the PROCESSING feature.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Previous patch that was intended to reduce stack usage within common
i/o layer didn't consider implicit memset(..., 0, ...) used with the
initializations used before.
Add these missing memsets wherever it's not obvious that the
concerned memory region is zeroed. This should give the same semantics
as before.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert GET_IPL_DEVICE assembler macro to C function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
qdio_get_micros is supposed to return microseconds. The get_clock()
return value needs to be shifted by 12 to get to microseconds.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use do { } while (0) constructs instead of empty defines to avoid
subtle compile bugs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is now possible to specify a ccw/fcp dump device which is used to
automatically create a system dump in case of a kernel panic. The dump
device can be configured under /sys/firmware/dump.
In addition it is now possible to specify a ccw/fcp device which is used
for the next reboot of Linux. The reipl device can be configured under
/sys/firmware/reipl.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Calls to set a device online with path grouping may get stuck in
some cases because certain device conditions where discarded after
unsolicited interrupts.
Check subchannel activity after unsolicited interrupts and retry
the operation if the subchannel is idle.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Devices enter no-path state after disabling a channel path
via the SE even though another path has been reenabled at the SE.
The devices are set into no-path state before triggering path
verification even though other paths may have become available.
To fix this trigger path verification before setting a device into
no-path state.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use different kind of assignment to make sure gcc doesn't create code
that creates temp variables on the stack, assigns values to it and
copies the content of the whole temp variable to the destination.
This reduces stack usage of e.g. ccwgroup_driver_register from 976
to 48 bytes instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I/O on a CCW device may stall if a channel path to that device is
logicaly varied off/on. A user I/O interrupt can get misinterpreted
as interrupt for an internal path verification operation due to a
missing check and is therefore never reported to the device driver.
Correct check for pending interruptions before starting path
verification.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do a retry of read device characteristics / read configuration
data when a deferred condition code 1 is encountered in
ccw_device_wake_up().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fail to create a ccwgroup device if a ccw device is passed in twice.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In special conditions where a subchannel rejects the HALT I/O-
instruction with a busy indication (cc 2), I/O may stall.
I/O request termination logic retries HALT I/O indefinitely
because it expects HALT I/O to alter the subchannel status which
is not true when cc 2 is returned.
In case of a busy indication, try CLEAR I/O instruction immediately.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Display avg_sample_interval in nanoseconds, like it is documented.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
1. Multipath devices for which SetPGID is not supported are not handled well.
Use NOP ccws for path verification (sans path grouping) when SetPGID is not
supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
first one) and try to find a common one. Moan if no common PGID can be
found (and use NOP verification). If no PGIDs have been set, use the css
global PGID (as before). (Rationale: SetPGID will get a command reject if
the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
will remove the old PGIDs. rcp will generate solicited CRWs which can be
savely ignored by the machine check handler (all other actions create
unsolicited CRWs).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a reg_mutex to prevent unregistering a subchannel before it has been
registered. Since 2.6.17, we've seen oopses in kslowcrw when a device is
found to be not operational during sense id when doing initial device
recognition; it is not clear yet why that particular problem was not (yet)
observed with earlier kernels...
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
irqtrace support for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes for several channel measurement facility bugs:
* Blocks copied from the hardware might not be consistent. Solve this
by moving the copying into idle state and repeating the copying.
* avg_sample_interval changed with every read, even though no new block
was available. Solve this by storing a timestamp when the last new
block was received.
* Several locking issues.
* Measurements were not reenabled after a disconnected device became
available again.
* Remove #defines for ioctls that were never implemented.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After setting a path to a dasd offline at the SE, I/O hangs on that
dasd for 5 minutes, then continues.
I/O for which an interrupt will not be reported after the channel
path has been disabled was not terminated by the common I/O layer,
causing the dasd MIH to hit after 5 minutes.
Be more aggressive in terminating I/O after setting a channel path
offline. Also make sure to generate a fake irb if the device
driver issues an I/O request after being notified of the killed
I/O and clear residual information from the irb before trying to
start the delayed verification.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Changes in the DASD driver require an asynchronous implementation of the
subchannel reprobe loop. This loop was so far only used by the blacklisting
mechanism but is now available to all CCW device drivers.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Work around the problem that a device cannot be unregistered from
driver_for_each_device() because of klist node refcounting: Get device
after device owned by the driver to be unregistered with driver_find_device()
and then unregister it. This works because driver_get_device() gets us out of
the region of the elevated klist node refcount. driver_find_device() will
always get the next device in the list after the found one has been
unregistered.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Specify correct sizeof() in chp_measurement_read() and return
correct amount of read data.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Trying to set a DASD root device online can fail under some circumstances
with the message "Read configuration data returned error -5". The cause
is that read configuration data incorrectly aborts with -EIO when it
encounters a temporary busy condition at a storage server.
Perform retry when encountering temporary busy conditions.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
From: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
The path grouping can fail due to non-unique pathgroup-IDs. The source for
the CPU-ID part of the ID was incorrectly specified on 64 bit systems.
Additionally, the length of the ID was too large due to incorrect data packing
declaration. Fix CPU-ID lowcore address and add missing packing declaration.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_SLAB_DEBUG=y networking over qeth doesn't work. The problem is
that the qib structure embedded in the qeth_irq structure needs an alignment
of 256 but kmalloc only guarantees an alignment of 8. When using SLAB
debugging the alignment of qeth_irq is not sufficient for the embedded qib
structure which causes all users of qdio (qeth and zfcp) to stop working.
Allocate qeth_irq structure with __get_free_page. That wastes a small amount
of memory (~2500 bytes) per online adapter.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid memory allocation with GFP_KERNEL in qdio_establish/qdio_shutdown. Use
memory pool instead. (Otherwise this can lead to an I/O stall where qdio
waits for a free page and zfcp waits for end of error recovery in low memory
situations.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Interrupts can stay disabled if an error occurred in _chp_add(). Use
spin_unlock_irq on the error paths to reenable interrupts.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a race condition in the I/O termination logic. The race can cause I/O to
a dasd device to fail with no retry left after turning one channel path to the
device off and on multiple times.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Debugging events in cio_trace/hex_ascii are truncated for some trace entries.
Increase trace event size to 16 bytes to cover longer text events, make
CIO_HEX_EVENT an inline function that loops to cover bigger hex events.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cio_ignore_proc_init() returns 1 in case of success and 0 in case of failure.
The caller tests for != 0, so better return 0 in case of success and -ENOENT
in case of failure.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert all kmalloc + memset sequences in drivers/s390 to kzalloc usage.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gather extended measurements for channel paths from the channel subsystem and
expose them to userspace via a sysfs attribute.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When cio waits for the interrupt for a basic sense, interrupts for hsch() or
csch() issued in the meantime are wrongly counted as interrupts for the basic
sense and the accumulated irb is passed to the device driver. In
ccw_device_w4sense(), check for clear or halt function in the irb and pass the
irb for the csch() or hsch() to the device driver.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems this patch got dropped (it was in addition to the `s390:
improve response code handling in chsc_enable_facility()' patch).
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than checking for some known failures, check positively for the
success response code 0x0001 and return -EIO for unrecognized failure
response codes.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Greg Smith <gsmith@nc.rr.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using FCP devices with V=V support, the input queue stalled when CCQ 97 had
been returned in qdio_do_eqbs. When this happen we have to reissue the eqbs
instruction.
Another bug was when V=V was enabled we checked if hardware has SIGA-sync
support. If not we returned with 0 from tiqdio_is_inbound_q_done. Thus qdio
lost initiative on FCP devices and input queue stalled. Running devices in
V=V there is no SIGA-sync support but nevertheless we have to process
tiqdio_is_inbound_q_done either.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If __ccw_device_disband_start() fails to initiate disbanding, it should finish
with ccw_device_disband_done() (which leaves the device in offline state)
instead of ccw_device_verify_done() (which leaves the device in online state).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix locking in __chp_add() and s390_subchannel_remove_chpid(): Need to
disable/enable because they are always called from a thread (and not
directly from a machine check...)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix modalias for ccw devices: cu_type should be in capitals as well.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The return code of ccw_device_probe_console() is not properly handled. It
should only return a valid ccw device pointer or a error value converted by
ERR_PTR. Fix the console driver code to check with IS_ERR instead against
NULL.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove all CVS generated information like e.g. revision IDs from
drivers/s390 and include/asm-s390 (none present in arch/s390).
- Add newline at end of arch/s390/lib/Makefile to avoid diff message.
Acked-by: Andreas Herrmann <aherrman@de.ibm.com>
Acked-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The chps[] array in struct channel_subsystem is one too short; therefore the
code doesn't realize the chpid ff is already known. When several devices on
chpid ff become available, the message "new_channel_path: could not register
ff" is displayed for every device but the first one.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch converts css_bus_type and ccw_bus_type to use
the new bus_type methods.
Signed-off-by: Cornelia Huck <huckc@de.ibm.com>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Use kzalloc() in blacklist.c.
- Kill unwanted casts in blacklist.c.
- Provide release function for struct channel_subsystem.
Signed-off-by: Cornelia Huck <huckc@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for multiple subchannel sets. Works with arbitrary devices in
subchannel set 1 and is transparent to device drivers. Although currently
only two subchannel sets are available, this will work with the architectured
maximum number of subchannel sets as well.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert /proc/cio_ignore to a sequential file. This makes multiple subchannel
sets support easier.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
struct channel_subsystem encapsulates several per channel subsystem
properties, like status of chpids or the global path group id.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for_each_subchannel() is an iterator calling a function for every possible
subchannel id until non-zero is returned. Convert the current iterating
functions to it.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces a struct subchannel_id containing the subchannel number
(formerly referred to as "irq") and switches code formerly relying on the
subchannel number over to it.
While we're touching inline assemblies anyway, make sure they have correct
memory constraints.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New feature V=V qdio pass-through.
QDIO and HiperSockets processing in z/VM V=V guest environments (as well as
V=R with z/VM running in LPAR mode) requires shadowing of all QDIO
architecture queue elements. Especially the shadowing of SBALs and SLSBs
structures in the hypervisor, and the need to issue SIGA SYNC operations to
observe state changes, eventually causes significant CPU processing overhead
in the hypervisor.
The QDIO pass-through support for V=V guests avoids the shadowing of SBALs and
SLSBs. This significantly reduces the hypervisor overhead for QDIO based I/O.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extract the s390_root_dev_* functions from the common I/O layer as they are
also used by non-ccw device drivers.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we receive path not operational indications (pnom in pmcw nonzero), we
switch off those paths. To catch them becoming available again, we have to
recalculate the lpm from the pmcw each time we start path verification.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh Dickins <hugh@veritas.com>
Fix the broken atomic_cmpxchg primitive. Add atomic_sub_and_test,
atomic64_sub_return, atomic64_sub_and_test, atomic64_cmpxchg,
atomic64_add_unless and atomic64_inc_not_zero. Replace old style
atomic_compare_and_swap by atomic_cmpxchg. Shorten the whole header by
defining most primitives with the two inline functions atomic_add_return and
atomic_sub_return.
In addition this patch contains the s390 related fixes of Hugh's "mm: fill
arch atomic64 gaps" patch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The first of these changes s/hotplug/uevent/ was needed to
compile sn2_defconfig (ia64/sn). The other three files
changed are blind changes of all remaining bus_type.hotplug
references I could find to bus_type.uevent.
This patch attempts to finish similar changes made in the
gregkh-driver-kill-hotplug-word-from-driver-core Nov 22 patch.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the drivers/s390/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/s390/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Cornelia Huck <cohuck@de.ibm.com>
Acked-by: Stefan Bader <Stefan.Bader@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the interface for setting ccw group devices on-/offline consistent with
that for ccw devices: Check if the device driver provided a set_{on,off}line
function and just set the device on-/offline if not.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch exports modalias for ccw devices.
So you can do:
modprobe `echo /sys/device/path_to_device/modalias`
and the proper driver will automatically be loaded by userspace.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Search for a disconnect ccw_device on the ccw bus rather than on the css
bus (was a typo in patch I did for the klist conversion). A cast to an
embedding ccw_device from an embedded device in a struct subchannel will
lead us to oopses.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add the helper and use it instead of open coding the klist_node_attached() check
(which is a layering violation IMHO)
idea by Alan Stern.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Calculate correct size for bl_dev array. It should be 8KB instead of 512KB
for 2^16 bits.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Common i/o layer changes:
- Collect the irb at the correct subchannel when waiting for the clear
interrupt during subchannel cleaning befor reIPL - don't stop at the first
interrupt that comes in.
- Change "extern __inline__" to "static inline".
- Remove unneeded qdio includes.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
