A FTM responder may do PASN authentication with unassociated stations
to allow secure ranging. In this case, the driver will add an internal
station and install the TK so the FW will accept protected FTM
request frames from this station and will send a protected FTM
response frame.
In addition, the driver needs to configure the HLTK to the FW so
the FW can derive the secure LTF bits. This is left for a later
patch since it is not yet supported by the FW.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.c915b44ad7dd.I72ef7f9753964555561c27ec503241105eddb14e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Evaluate the appropriate DSM from ACPI to set ETSI SRD 5.8GHz
channels to passive or disabled, default behaviour is enabled.
Add enums and refactor evaluation of DSM functions for better
readablity and more informative debug prints.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.816130ee75e0.I727a217be7c967a97960b197a816fc053d10c48a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is an issue in the HW DMA engine in the 9000 family of devices
when more than 6 RX queues are used. The issue is that the FW may
hang when IWL_MVM_RXQ_NSSN_SYNC notifications are sent.
Fix this by limiting the number of RX queues to 6 in the 9000 family
of devices.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.37d90f9ceb0c.I8dfe8a7d3a7ac9f0bc9d93e4a03f8165d8c999d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are reports that 8822CE fails to work rtw88 with "failed to read DBI
register" error. Also I have a system with 8723DE which freezes the whole
system when the rtw88 is probing the device.
According to [1], platform firmware may not properly power manage the
device during shutdown. I did some expirements and putting the device to
D3 can workaround the issue.
So let's power cycle the device by putting the device to D3 at shutdown
to prevent the issue from happening.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=206411#c9
BugLink: https://bugs.launchpad.net/bugs/1872984
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200928165508.20775-1-kai.heng.feng@canonical.com
Song Liu says:
====================
This set introduces BPF_F_PRESERVE_ELEMS to perf event array for better
sharing of perf event. By default, perf event array removes the perf event
when the map fd used to add the event is closed. With BPF_F_PRESERVE_ELEMS
set, however, the perf event will stay in the array until it is removed, or
the map is closed.
---
Changes v3 => v5:
1. Clean up in selftest. (Alexei)
Changes v2 => v3:
1. Move perf_event_fd_array_map_free() to avoid unnecessary forward
declaration. (Daniel)
Changes v1 => v2:
1. Rename the flag as BPF_F_PRESERVE_ELEMS. (Alexei, Daniel)
2. Simplify the code and selftest. (Daniel, Alexei)
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add tests for perf event array with and without BPF_F_PRESERVE_ELEMS.
Add a perf event to array via fd mfd. Without BPF_F_PRESERVE_ELEMS, the
perf event is removed when mfd is closed. With BPF_F_PRESERVE_ELEMS, the
perf event is removed when the map is freed.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200930224927.1936644-3-songliubraving@fb.com
Currently, perf event in perf event array is removed from the array when
the map fd used to add the event is closed. This behavior makes it
difficult to the share perf events with perf event array.
Introduce perf event map that keeps the perf event open with a new flag
BPF_F_PRESERVE_ELEMS. With this flag set, perf events in the array are not
removed when the original map fd is closed. Instead, the perf event will
stay in the map until 1) it is explicitly removed from the array; or 2)
the array is freed.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200930224927.1936644-2-songliubraving@fb.com
Calls to kzalloc() and kvzalloc() should be null-checked
in order to avoid any potential failures. In this case,
a potential null pointer dereference.
Fix this by adding null checks for _parse_attr_ and _flow_
right after allocation.
Addresses-Coverity-ID: 1497154 ("Dereference before null check")
Fixes: c620b77215 ("net/mlx5: Refactor tc flow attributes structure")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This code frees "shared_counter" and then dereferences on the next line
to get the error code.
Fixes: 1edae2335a ("net/mlx5e: CT: Use the same counter for both directions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When removing a flow from the slow path fdb, a flow attr struct is
allocated for the rule removal process. If the allocation fails the
code prints a warning message but continues with the removal flow
which include dereferencing a pointer which could be null.
Fix this by exiting the function in case the attr allocation failed.
Fixes: c620b77215 ("net/mlx5: Refactor tc flow attributes structure")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Use the PCI device directly for dma accesses as non PCI device unlikely
support IOMMU and dma mappings.
Introduce and use helper routine to access DMA device.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Set flow source as hint for local vport.
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently devlink eswitch ports are registered and unregistered by the
representor layer.
However it is better to register them at eswitch layer so that in future
user initiated command port add and delete commands can also
register/unregister devlink ports without depending on representor layer.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
To register and unregister devlink ports when loading/unload
representors, refactor the code to helper functions.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently only VF vports need egress ACL table.
Add a generic helper to check whether a vport need egress
ACL table or not.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently only 256 vports can be supported as only 8 bits are
reserved for them and 8 bits are reserved for vhca_ids in
metadata reg c0. To support more than 256 vports, replace
vhca_id with a unique shorter 4-bit PF number which covers
upto 16 PF's. Use remaining 12 bits for vports ranging 1-4095.
This will continue to generate unique metadata even if
multiple PCI devices have same switch_id.
Signed-off-by: sunils <sunils@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Skip the rule according to flow arrival source, in case of RX and the
source is local port skip and in case of TX and the source is uplink
skip, we get this info according to the flow source hint we get from
upper layers when creating the rule.
This is needed because for example in case of FDB table which has a TX
and RX tables and we are inserting a rule with an encap action which
is only a TX action, in this case rule will fail on RX, so we can rely
on the flow source hint and skip RX in such case.
Until now we relied on metadata regc_0 that upper layer mapped the
port in the regc_0, but the problem is that upper layer did not always
use regc_0 for port mapping, so now we added support to flow source
hint which upper layers will pass to SW steering when creating a rule.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Hamdan Igbaria <hamdani@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Instead of getting the tag in each function, call the builder
directly with the tag. This will allow to use the same function
for building the tag and the bitmask.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The misc3 variable is used only once and can be dropped.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When we create a matcher we check that all fields are consumed.
There is no need for this specific check. This keeps the STE
builder functions simple and clean.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Mask validity for ste builders is checked by mlx5dr_ste_build_pre_check
during matcher creation.
It already checks the mask value of source_vport, so removing
this duplicated check.
Also, moving there the check of source_eswitch_owner_vhca_id mask.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Validity check is done by reading the next lu_type from the STE,
this check can be replaced by checking the refcount.
This will make the check independent on internal STE structure.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fix a build failure on arm64, due to missing alignment information for
the .BTF_ids section:
resolve_btfids.test.o: in function `test_resolve_btfids':
tools/testing/selftests/bpf/prog_tests/resolve_btfids.c:140:(.text+0x29c): relocation truncated to fit: R_AARCH64_LDST32_ABS_LO12_NC against `.BTF_ids'
ld: tools/testing/selftests/bpf/prog_tests/resolve_btfids.c:140: warning: one possible cause of this error is that the symbol is being referenced in the indicated code as if it had a larger alignment than was declared where it was defined
In vmlinux, the .BTF_ids section is aligned to 4 bytes by vmlinux.lds.h.
In test_progs however, .BTF_ids doesn't have alignment constraints. The
arm64 linker expects the btf_id_set.cnt symbol, a u32, to be naturally
aligned but finds it misaligned and cannot apply the relocation. Enforce
alignment of .BTF_ids to 4 bytes.
Fixes: cd04b04de1 ("selftests/bpf: Add set test to resolve_btfids")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Link: https://lore.kernel.org/bpf/20200930093559.2120126-1-jean-philippe@linaro.org
Ido Schimmel says:
====================
drop_monitor: Convert to use devlink tracepoint
Drop monitor is able to monitor both software and hardware originated
drops. Software drops are monitored by having drop monitor register its
probe on the 'kfree_skb' tracepoint. Hardware originated drops are
monitored by having devlink call into drop monitor whenever it receives
a dropped packet from the underlying hardware.
This patch set converts drop monitor to monitor both software and
hardware originated drops in the same way - by registering its probe on
the relevant tracepoint.
In addition to drop monitor being more consistent, it is now also
possible to build drop monitor as module instead of as a builtin and
still monitor hardware originated drops. Initially, CONFIG_NET_DEVLINK
implied CONFIG_NET_DROP_MONITOR, but after commit def2fbffe6
("kconfig: allow symbols implied by y to become m") we can have
CONFIG_NET_DEVLINK=y and CONFIG_NET_DROP_MONITOR=m and hardware
originated drops will not be monitored.
Patch set overview:
Patch #1 adds a tracepoint in devlink for trap reports.
Patch #2 prepares probe functions in drop monitor for the new
tracepoint.
Patch #3 converts drop monitor to use the new tracepoint.
Patches #4-#6 perform cleanups after the conversion.
Patch #7 adds a test case for drop monitor. Both software originated
drops and hardware originated drops (using netdevsim) are tested.
Tested:
| CONFIG_NET_DEVLINK | CONFIG_NET_DROP_MONITOR | Build | SW drops | HW drops |
| -------------------|-------------------------|-------|----------|----------|
| y | y | v | v | v |
| y | m | v | v | v |
| y | n | v | x | x |
| n | y | v | v | x |
| n | m | v | v | x |
| n | n | v | x | x |
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that drop monitor correctly captures both software and hardware
originated packet drops.
# ./drop_monitor_tests.sh
Software drops test
TEST: Capturing active software drops [ OK ]
TEST: Capturing inactive software drops [ OK ]
Hardware drops test
TEST: Capturing active hardware drops [ OK ]
TEST: Capturing inactive hardware drops [ OK ]
Tests passed: 4
Tests failed: 0
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, devlink called into drop monitor in order to report hardware
originated drops / exceptions. devlink intentionally filtered control
packets and did not pass them to drop monitor as they were not dropped
by the underlying hardware.
Now drop monitor registers its probe on a generic 'devlink_trap_report'
tracepoint and should therefore perform this filtering itself instead of
having devlink do that.
Add the trap type as metadata and have drop monitor ignore control
packets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'struct net_dm_hw_metadata' is a duplicate of 'struct
devlink_trap_metadata'.
Remove the former and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old probe functions that were invoked by drop monitor code are no
longer called and can thus be removed. They were replaced by actual
probe functions that are registered on the recently introduced
'devlink_trap_report' tracepoint.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert drop monitor to use the recently introduced
'devlink_trap_report' tracepoint instead of having devlink call into
drop monitor.
This is both consistent with software originated drops ('kfree_skb'
tracepoint) and also allows drop monitor to be built as a module and
still report hardware originated drops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop monitor supports two alerting modes: Summary and packet. Prepare a
probe function for each, so that they could be later registered on the
devlink tracepoint by calling register_trace_devlink_trap_report(),
based on the configured alerting mode.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a tracepoint for trap reports so that drop monitor could register
its probe on it. Use trace_devlink_trap_report_enabled() to avoid
wasting cycles setting the trap metadata if the tracepoint is not
enabled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAl90420THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqdH0B/0bI+/KTQAN7OGq7pyBGUwzD8VEsJop
si5JAGVBIi3RYimJRqZ3Q3+vJ/cT4rp1NJMaVRzE6xxqvxp4T4hWBB5y8KBp39zC
8PjbIlI0RDqYnKAGd/9DXxkLHlbN9FwYSBpjIezzfEnRNhtnxJTMvDQ/nEUi+EEw
x2HAw8P4Vvodc55CjPinpKRBpRQr8KKknkZ36idvKw3yuYzYPYcee3C70YK0GNOE
SI8JXf9IV1cvDWleS6r93K03A/4cQdH/MQmuJWrz/wQoHnU7E+v1pLyI6/GxWAaQ
YsOiVKisw+TqZUaGFlw+ZqqYrqsEjmwRYUzpzwLkLS0sCE8ntwInSZo6
=W8ez
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.10-20200930' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2020-09-30
this is a pull request of 13 patches for net-next.
The first 10 target the mcp25xxfd driver (which is renamed to mcp251xfd during
this series).
The first two patches are by Thomas Kopp, which adds reference to the just
related errata and updates the documentation and log messages.
Dan Carpenter's patch fixes a resource leak during ifdown.
A patch by me adds the missing initialization of a variable.
Oleksij Rempel updates the DT binding documentation as requested by Rob
Herring.
The next 5 patches are by Thomas Kopp and me. During review Geert Uytterhoeven
suggested to use "microchip,mcp251xfd" instead of "microchip,mcp25xxfd" as the
DT autodetection compatible to avoid clashes with future but incompatible
devices. We decided not only to rename the compatible but the whole driver from
"mcp25xxfd" to "mcp251xfd". This is done in several patches.
Joakim Zhang contributes three patches for the flexcan driver. The first one
adds support for the ECC feature, which is implemented on some modern IP cores,
by initializing the controller's memory during ifup. The next patch adds
support for the i.MX8MP (which supports ECC) and the last patch properly
disables the runtime PM if device registration fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson says:
====================
ionic watchdog training
Our link watchdog displayed a couple of unfriendly behaviors in some recent
stress testing. These patches change the startup and stop timing in order
to be sure that expected structures are ready to be used by the watchdog.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In one corner case scenario, the driver device lif setup can
get delayed such that the ionic_watchdog_cb() timer goes off
before the ionic->lif is set, thus causing a NULL pointer panic.
We catch the problem by checking for a NULL lif just a little
earlier in the callback.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be better at making sure we don't have a link check
watchdog go off while we're shutting things down, so let's stop
the timer as soon as we start the remove.
Meanwhile, since that was the only thing in
ionic_dev_teardown(), simplify and remove that function.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp: exponential backoff in tcp_send_ack()
We had outages caused by repeated skb allocation failures in tcp_send_ack()
It is time to add exponential backoff to reduce number of attempts.
Before doing so, first patch removes icsk_ack.blocked to make
room for a new field (icsk_ack.retry)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
