LS3 has a selectable current limit.
Change units to microamp in the example.
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document device-tree settings of the load-switch LS2
in the tps65218 device.
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FAN53526 differs from the FAN53555 only in that the mode bit in
VSEL0/VSEL1 is moved to the CONTROL register, the voltage selector mask
is extended by 1 bit and the step is different.
So extend the existing fan53555 driver to support FAN53526 as well.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for active discharge for USB power switches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator high pull down are enabled by default so remove support in the
driver.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt parent description is not needed as the parent is a parent
node with 'interrupt-controller' property.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.
Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed regulators do not have associated bus addresses and are typically
placed directly under the root node where their names must still be
unique despite not having a unit address.
Fix the malformed example node which had a unit address but no "reg"
property by dropping the unit address.
Also, try to make the example more useful by using the recommended
generic node name "regulator", but with a suffix reflecting the
regulator name in order to make it unique.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the DT binding document for max77650 regulators.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ROHM bd70528 is a ultra low power PMIC which includes
3 bucks, 3 LDOs and 2 LED drivers. Document the bindings
for them.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the fixed-regulator binding to DT schema format using
json-schema.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix few trivial language typos in core and drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch describes the compatible and the device tree
bindings necessary for the MCP16502 PMIC.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for regulator modes and suspend states.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Redefine binding for regulator-coupled-max-spread property in a way that
max-spread values are defined per regulator couple instead of defining
single max-spread for the whole group of coupled regulators.
With that change the following regulators coupling configuration will be
possible:
regA: regulatorA {
regulator-coupled-with = <®B ®C>;
regulator-coupled-max-spread = <100000 300000>;
};
regB: regulatorB {
regulator-coupled-with = <®A ®C>;
regulator-coupled-max-spread = <100000 200000>;
};
regC: regulatorC {
regulator-coupled-with = <®A ®B>;
regulator-coupled-max-spread = <300000 200000>;
};
Note that the regulator-coupled-max-spread property does not have any
users yet, hence it's okay to change the binding.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For state-mem and state-disk regulators can have
various parameters applied such as enabled/disabled,
current mode, voltage etc.
This patch adds documentation on how to set these parameters
in the device tree for the standby state.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain hardware may require supply voltage to be changed in steps. Define
new property that allow to describe such hardware.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Redefine binding for regulator-coupled-max-spread property in a way that
max-spread values are defined per regulator couple instead of defining
single max-spread for the whole group of coupled regulators.
With that change the following regulators coupling configuration will be
possible:
regA: regulatorA {
regulator-coupled-with = <®B ®C>;
regulator-coupled-max-spread = <100000 300000>;
};
regB: regulatorB {
regulator-coupled-with = <®A ®C>;
regulator-coupled-max-spread = <100000 200000>;
};
regC: regulatorC {
regulator-coupled-with = <®A ®B>;
regulator-coupled-max-spread = <300000 200000>;
};
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The STPMIC1 regulators supply power to the application processor as well as
to the external system peripherals such as DDR, Flash memories and system
devices.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the BD71847 which touches both MFD and regulator.
There's a few other bits and pieces included as some dependency patches
had already been applied so would've required rebasing.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuM/8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Az7B/4ye6MIEn8hwKmS36NU3oCvCTFiOZHe
W+T1/O7gOYPSOeHk/4SA8v+A0X2ry+zCschSJtnGDWeZwiZmuhSbQO3SKKM+iAKJ
R1UFioMVd8cr8UySX0ddSdFit+rI+FcZHd8TYAjbseX+0YKZX7z7/rXPVhSEhdU3
BxRy58DJRbLxYofiGruvDd/sj6VFukVmLRjQUE5SqZ8aTKXBbrT7h0Jgi3m7aOmK
g/a+ulMNecq8884oQuBjj1+xCuT02GJsT04BKaXEBsAFX1Fh8IyOxej2N2PaX1z/
6HoPjSAac/Gl9BAgpV0YDdEJJR8yumkdDJubF3SayMyoiv16zMTT1fvC
=t0Ni
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuNaMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H/3B/9u/IGN9LWSnauAivTDqZGx1V3a97e2
ijZSiWaTWFmIBPUNIJgDQirdqsX61Mgu9mTbeD9+tmi2Mm4AOZRJT4pdtzZCehWT
HQuN4dcF9heftf/6Q4c+5yZFAJzOJHHuFklNdDAuM12rUp5IDpKxIo2nrx7MDN6r
RgrxK6eTluvOL4+VJwN/VqXRBWfN857uMjaGkbFV3CrYJh2Ktumts3IcFd18Cpvd
U3gBUYNsPBiQtmGXFkrCCBaYWqn5Ry91CAvpTjoJdZx50xbeXVOEUnUMaidQ4/ru
XL+PqcdTovKuV5OhMzra5MCVt3Cv8Oc/21KeNvFEIV3X6O531LEcksDx
=zN+p
-----END PGP SIGNATURE-----
Merge tag 'bd71847-support' into regulator-4.20
regulator/mfd: Support for the ROHM BD71847
This adds support for the BD71847 which touches both MFD and regulator.
There's a few other bits and pieces included as some dependency patches
had already been applied so would've required rebasing.
Add ROHM BD71847 Power Management IC regulator binding information to
device-tree binding documents.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PMS405 provdies 5 SMPS regulators and 13 LDOs, add these to the RPM
regulator driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the new optional "fsl,pmic-stby-poweroff" property.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Remove an obsolete hack for PPC32 longtrail systems
- Make of_io_request_and_map() "name" arg optional
- Add vendor prefixes for bitmain, Asus, and Y Soft
- Remove 'interrupt-parent' from bindings as it is implicit
- New properties for wm8994 audio codec
- Add 'clocks' property support to SRAM binding
- Add binding for ASPEED coprocessor interrupt controller
- Various binding spelling and link fixes
-----BEGIN PGP SIGNATURE-----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=AV4E
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Remove an obsolete hack for PPC32 longtrail systems
- Make of_io_request_and_map() "name" arg optional
- Add vendor prefixes for bitmain, Asus, and Y Soft
- Remove 'interrupt-parent' from bindings as it is implicit
- New properties for wm8994 audio codec
- Add 'clocks' property support to SRAM binding
- Add binding for ASPEED coprocessor interrupt controller
- Various binding spelling and link fixes
* tag 'devicetree-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: remove dynamic-resolution-notes reference to non-existent file
dt-bindings: Add Y Soft Corporation vendor prefix
of/fdt: Remove PPC32 longtrail hack in memory scan
dt-bindings: remove 'interrupt-parent' from bindings
pinctrl: tegra: fix spelling in devicetree binding document
usb: dwc3: rockchip: Fix PHY documentation links.
dt-bindings: sound: wm8994: document wlf,csnaddr-pd property
dt-bindings: sound: wm8994: document wlf,spkmode-pu property
dt-bindings: sram: Add 'clocks' as an optional property
dt-bindings: Add vendor prefix for AsusTek Computer Inc.
dt-bindings: misc: ASPEED coprocessor interrupt controller
dt-bindings: gpio: pca953x: Document interrupts, update example
drivers/of: Make of_io_request_and_map() "name" argument optional
dt-bindings: Add bitmain vendor prefix
Documentation: devicetree: tilcdc: fix spelling mistake "suppors" -> "supports"
Introduce bindings for RPMh regulator devices found on some
Qualcomm Technlogies, Inc. SoCs. These devices allow a given
processor within the SoC to make PMIC regulator requests which
are aggregated within the RPMh hardware block along with requests
from other processors in the SoC to determine the final PMIC
regulator hardware state.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Added support for the CPCAP power management regulator functions on
Tegra based Motorola Xoom devices.
Added sw2_sw4 value tables, which provide power to the Tegra core and
aux devices.
Added the Xoom init tables and device tree compatibility match.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This binding is used to keep the backward compatibility with the current
dtb's [1]. The binding informs the driver that the unused switch regulators
can be disabled.
If it is not specified, the driver doesn't disable the switch regulators.
[1] https://patchwork.kernel.org/patch/10490381/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DT bindings for regulators implemented in UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same general chip description was written in MFD and Regulator
binding documents for ROHM bd71837 PMIC. Remove description from
regulator binding as suggested by Rob H.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Multiple binding documents have various forms of unbalanced quotation
marks. Fix them.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch extends binding according to support the pfuze3001 chip.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document devicetree bindings for ROHM BD71837 PMIC regulators.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the DT bindings for the SAW regulators.
The saw-leader is the only property that is configurable in DT.
The saw-slave property allows ganging (grouping) of
several regulators so that their outputs can be combined.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators require keeping their voltage spread below defined
max_spread.
Add properties to provide information on regulators' coupling.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a common device tree property for regulator nodes to support
the specification of allowed operating modes.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SY8106A is an I2C-controlled adjustable voltage regulator made by
Silergy Corp.
Add its device tree binding.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Change commit message and slight fixes]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to Devicetree Specification v0.2 document:
"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model."
Do as suggested in the binding example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the pm8998 and pmi8998 regulators as used in the MSM8998 platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The only device-specific node names are "buck1" and "buck2" for the two
regulators present on the device. Sleep mode GPIO and per-regulator GPIO
enable pins are not exposed (the driver does not support them either).
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
These two drivers fail to probe if no name is provided. For details see:
https://www.spinics.net/lists/kernel/msg2457515.html
Signed-off-by: Harald Geyer <harald@ccbib.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Convert to use memblock_virt_alloc in DT code which supports bootmem
arches. With this we can remove the arch specific
early_init_dt_alloc_memory_arch() functions.
- Enable running the DT unittests on UML
- Use SPDX license tags on DT files
- Fix early FDT kconfig ifdef logic
- Clean-up unittest Makefile
- Fix function comment for of_irq_parse_raw
- Add missing documentation for linux,initrd-{start,end} properties
- Clean-up of binding examples using uppercase hex
- Add trivial devices W83773G and Infineon TLV493D-A1B6
- Add missing STM32 SoC bindings
- Various small binding doc fixes
-----BEGIN PGP SIGNATURE-----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=v6gj
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Convert to use memblock_virt_alloc in DT code which supports
bootmem arches. With this we can remove the arch specific
early_init_dt_alloc_memory_arch() functions.
- Enable running the DT unittests on UML
- Use SPDX license tags on DT files
- Fix early FDT kconfig ifdef logic
- Clean-up unittest Makefile
- Fix function comment for of_irq_parse_raw
- Add missing documentation for linux,initrd-{start,end} properties
- Clean-up of binding examples using uppercase hex
- Add trivial devices W83773G and Infineon TLV493D-A1B6
- Add missing STM32 SoC bindings
- Various small binding doc fixes
* tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (23 commits)
xtensa: remove arch specific early DT functions
x86: remove arch specific early_init_dt_alloc_memory_arch
nios2: remove arch specific early_init_dt_alloc_memory_arch
mips: remove arch specific early_init_dt_alloc_memory_arch
metag: remove arch specific early DT functions
cris: remove arch specific early DT functions
libfdt: remove unnecessary include directive from <linux/libfdt.h>
of: unittest: refactor Makefile
of/fdt: use memblock_virt_alloc for early alloc
of: Use SPDX license tag for DT files
of/fdt: Fix #ifdef dependency of early flattree declarations
dt-bindings: h8300 clocksource: correct spelling of pulse
dt-bindings: imx6q-pcie: Add required property for i.MX6SX
mmc: Don't reference Linux-specific OF_GPIO_ACTIVE_LOW flag in DT binding
dt-bindings: Use lower case hex in unit-addresses
dt-bindings: display: panel: Fix compatible string for Toshiba LT089AC29000
dt-bindings: Add Infineon TLV493D-A1B6
dt-bindings: mailbox: ti,message-manager: Fix interrupt name error
dt-bindings: chosen: Document linux,initrd-{start,end}
dt-bindings: arm: document supported STM32 SoC family
...
Some systems need to set regulators to specific states when they enter
low power modes, especially around CPUs. There are many of these modes
depending on the particular runtime state.
Currently the regulator consumers are not granted permission to change
suspend state of regulator devices, the constraints are configured at
startup. In order to allow changes in a vlotage range, we need to add
new properties for voltage range and a flag to give permission to
change the suspend voltage and suspend on/off in suspend mode.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
