HDSP_VERSION_BIT has to be ORed with HDSP_S_LOAD. This fixes the detection
of at least some RME RPM boxes.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SNDRV_HDSPM_IOCTL_GET_STATUS is supposed to query the current card
status, so we have to return what we receive on the MADI wire (RX), not
what we transmit (TX) to others. The latter is a config item to be
queried via SNDRV_HDSPM_IOCTL_GET_CONFIG.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that Conexant CX20549 chip handle only a single input-amp even
though the audio-input widget has multiple sources. This has been never
clear, and I implemented in the current way based on the debug information
I got at the early time -- the device reacts individual input-amp values
for different sources. This is true for another Conexant codec, but it's
not applied to CX20549 actually.
This patch changes the auto-parser code to handle a single input-amp
per audio-in widget for CX20549. After applying this, you'll see only a
single "Capture" volume control instead of separate "Mic" or "Line"
captures when the device is set up to use a single ADC.
We haven't tested 20551 and 20561 codecs yet. If these show the similar
behavior like 20549, they need to set spec->single_adc_amp=1, too.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the old Conexant chips (5045, 5047, 5051 and 5066), a single EAPD
may handle both headphone and speaker outputs while it's assigned only
to one of them. Turning off dynamically leads to the unexpected silent
output in such a configuration with the auto-mute function.
Since it's difficult to know how the EAPD is handled in the actual h/w
implementation, better to keep EAPD on while running for such codecs.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC260 has multiple mixer widgets connected to the shared DAC, but the
driver currently doesn't check this possibility and ignores when the DAC
is shared with others. This resulted in the silent output from some
routes because of lack of the amp setup.
This patch adds the workaround for it by checking the route even with the
shared DAC, but also checking the conflict with the existing control for
the very same widget NID.
Reference: https://bugzilla.novell.com/show_bug.cgi?id=726812
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The association numbers of surround/CLFE speaker pins aren't correctly
mapped by the auto-parser. This patch fixes the CLFE speaker pin to the
right assoc value (from 3 to 1).
Tested-by: Nika Topolchanskaya <nanodesuu@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When 5.1 or more headphone or speaker pins are provided, the parser still
takes as is without fixing the order of channel mapping, which leads in
the unexpected strange channel order by surround outputs.
This patch fixes the issue by applying the same fix-up not only to
line_out_pins[] but also hp_pins[] and speaker_pins[].
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The revision 0x100300 was found for ALC662. It seems to work well
with patch_alc662.
Cc: stable@kernel.org
BugLink: http://bugs.launchpad.net/bugs/877373
Tested-by: Shengyao Xue <Shengyao.xue@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Acked-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a device has multiple speakers and still has the auto-mute support,
the driver copies line_outs[] to speaker_outs[]. And then it tries to
assign DACs for both. This ended up with the assignment only to the
primary DAC to all speakers.
This patch fixes the situation by checking the duplicated LO/SPK case
appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is patch for Conexant codec of Intel HDA driver, adding new quirk
for Lenovo Thinkpad T520 and W520. Conexant autodetection works fine for
T520 (similar subsystem ID is used also in W520 model) and detects more
mixer features compared to generic (fallback) Lenovo quirk with
hardcoded options in Conexant codec.
Patch was activelly tested with Linux 3.0.4, 3.0.6 and 3.0.7 without any
problems.
Signed-off-by: Daniel Suchy <danny@danysek.cz>
Cc: <stable@kernel.org> [3.0+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous fix for the position-buffer check gives yet another
regression on a Dell laptop. The safest fix right now is to add a
static quirk for this device (and better to apply it for stable
kernels too).
Reported-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The COEF #0 value represents a sort of device id, so it's supposedly
constant while operation. Better to use the cached value instead of
reading it at each time from the performance POV.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a static table for detecting the codec renames.
Also clean up the error paths in each patch_*() function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This typo caused headphone pins not to be initialized correctly.
BugLink: https://bugs.launchpad.net/bugs/871582
Reported-by: Effenberg
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The purpose of this patch is to remove a section of "bad" code that
assigns the last DAC to ports E or F in order to support notebooks
with docking in earlier days, around ALSA 1.0.19 - 21. This is not
necessary now and actually breaks some configurations that use these
ports as other devices. This have been tested on several different
configurations to make sure that it is working for different combinations.
Signed-off-by: Charles Chin <Charles.Chin@idt.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit ef18beded8 introduced a
mechanism to assign the previously used slot for the next reopen of a
PCM stream. But the PCM device number isn't always unique (it may
have multiple substreams), and also the code doesn't check the stream
direction, thus both playback and capture streams share the same
device number.
For avoiding this conflict, make a unique key for each substream and
store/check this value at reopening.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the speaker outputs are more than the headphone outputs, it implies
that the system has surround speakers while the headphones are only for
monitoring the front. In such a case, it's better to put speakers as
the primary outputs so that the driver can build up and keep the
surround setup. Otherwise the system will pick up the headphone as
primary, and offers less channels than the speakers do support.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since hda_proc.c is now the only user of snd_print_pcm_rates(), better to
put it back locally to hda_proc.c and revert to the old style.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SAD sampling rate information reported in
/proc/asound/cardX/eldX is incorrect due to a mismatch
between HDA and HDMI frequencies. Add new routine to provide
relevant values.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar to Line Out, these constants form the base for future
patches enabling input jack reporting for Line in jacks.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we run out of DACs when trying to assign a DAC to a secondary
headphone, prefer the DAC of the first headphone to the primary
(usually line out) DAC.
BugLink: http://bugs.launchpad.net/bugs/845275
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Sigmatel/IDT parser should have the same naming convention
for input jacks as the other codecs have.
BugLink: http://bugs.launchpad.net/bugs/859704
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Applications may want to read ELD information to
understand what codecs are supported on the HDMI
receiver and handle the a-v delay for better lip-sync.
ELD information is exposed in a device-specific
IFACE_PCM kcontrol. Tested both with amixer and
PulseAudio; with a corresponding patch passthrough modes
are enabled automagically.
ELD control size is set to zero in case of errors or
wrong configurations. No notifications are implemented
for now, it is expected that jack detection is used to
reconfigure the audio outputs.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit a810364a04
ALSA: hda - Handle -1 as invalid position, too
caused a regression on some machines that require the position-buffer
instead of LPIB, e.g. resulting in noises with mic recording with
PulseAudio.
This patch fixes the detection by delaying the test at the timing as
same as 3.0, i.e. doing the position check only when requested in
azx_position_ok().
Reported-and-tested-by: Rocko Requin <rockorequin@hotmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the ugly real world, there area really broken devices that don't set
codec SSID correctly. In such a case, the ID can be random, thus the
patching won't work reliably.
For applying the patch forcibly to such a device, the driver will skip
the vendor and/or subsystem ID checks when zero or a negative number is
given in [codec] section.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new option "snoop" for the traffic control of the HD-audio
controller chip. When set to 0, the non-snooping mode is used with
the traffic control bit is set in each stream control register.
This may allow better operations in the low power mode, but the actual
implementation is depending pretty much on the chipset.
As already implemented, more or less each chipset has own snoop-control
register bit. Now this setup refers to the snoop option, too.
Also, a new VIA chipset may require the non-snooping mode when set so
in BIOS. In such a case, the option value is overridden.
As default, it's still set to snoop=1 for keeping the same behavior as
before. In near future, it'll be set to 0 as default after checking
it works in every system well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since really_cleanup_stream() is called from both purity_inactive_streams()
and hda_cleanup_all_streams(), the verbs to clear the PCM channel and
format may be called multiple times unnecessarily.
This patch adds checks to skip these unneeded verbs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The spec->autocfg.line_out_pins[] may contain the same pins as hp_pins[]
depending on the configuration. When they are identical, detecting the
line_jack_present flag screws up the auto-mute because alc_line_automute()
is called unconditionally at initialization while it won't be triggered
by unsol events, thus the old line_jack_present flag is kept for the
whole run.
For fixing this buggy behavior, the driver needs to check whether the
line-outs are really individual, and skip if same as headphone jacks.
Reference: https://bugzilla.novell.com/show_bug.cgi?id=716104
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the headphone pin is assigned as primary output to line_out_pins[],
the automatic HP-pin assignment by ASSID must be suppressed. Otherwise
a wrong pin might be assigned to the headphone and breaks the auto-mute.
Reference: https://bugzilla.novell.com/show_bug.cgi?id=716104
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
This patch is necessary to make internal speakers work on this chip.
Cc: stable@kernel.org
BugLink: http://bugs.launchpad.net/bugs/854468
Tested-by: Alex Wolfson <alex.wolfson@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Add "AD198x Headphone" playback device for independent headphone playback
while playing 7.1 surround using rear panel audio jacks.
- Remove "6stack-dig-fp" model since "Headphone Playback Volume" control using
DAC0 instead of DAC1 (HDA_FRONT) was already added to all models.
- Add "Independent HP" switch to enable/disable this playback device.
When the switch is OFF, headphone use "copy front" mode to get the front
channel as the green jack.
When the switch is ON, you can play stereo sound through "AD198x Headphone"
device to headphone while playing 7.1 surround sound through "AD198x Analog"
device.
The switch cannot be changed when either "AD198x Headphone" or "AD198X Analog"
is open.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Smatch has a new check for Rosenberg type information leaks where
structs are copied to the user with uninitialized stack data in them.
The status struct has a hole in it, and on some paths not all the
members were initialized.
struct hdspm_status {
unsigned char card_type; /* 0 1 */
/* XXX 3 bytes hole, try to pack */
enum hdspm_syncsource autosync_source; /* 4 4 */
long long unsigned int card_clock; /* 8 8 */
The hdspm_version struct had holes in it as well.
struct hdspm_version {
unsigned char card_type; /* 0 1 */
char cardname[20]; /* 1 20 */
/* XXX 3 bytes hole, try to pack */
unsigned int serial; /* 24 4 */
short unsigned int firmware_rev; /* 28 2 */
/* XXX 2 bytes hole, try to pack */
int addons; /* 32 4 */
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 9676001559
("ALSA: fm801: add error handling if auto-detect fails") seems to
break systems that were previously working without a tuner.
As a bonus, this should fix init and cleanup for the case where the
tuner is explicitly disabled.
Reported-and-tested-by: Hor Jiun Shyong <jiunshyong@gmail.com>
References: http://bugs.debian.org/641946
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [v3.0+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 9676001559
("ALSA: fm801: add error handling if auto-detect fails") added
incorrect error handling.
Once we have successfully called snd_device_new(), the cleanup
function fm801_free() will automatically be called by snd_card_free()
and we must *not* also call fm801_free() directly.
Reported-by: Hor Jiun Shyong <jiunshyong@gmail.com>
References: http://bugs.debian.org/641946
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [v3.0+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since modern HDMI cards often have more than one output pin and thus
input device, we need to know which one has actually been plugged in.
This patch adds a name hint that indicates which PCM device is connected
to which pin.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Increase readability and understandability in the automute code.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
