RFC 4960 Errata 3.27 identifies that ssthresh should be adjusted to cwnd
because otherwise it could cause the transport to lock into congestion
avoidance phase specially if ssthresh was previously reduced by some
packet drop, leading to poor performance.
The Errata says to adjust ssthresh to cwnd only once, though the same
goal is achieved by updating it every time we update cwnd too. The
caveat is that we could take longer to get back up to speed but that
should be compensated by the fact that we don't adjust on RTO basis (as
RFC says) but based on Heartbeats, which are usually way longer.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.27
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4960 Errata 3.26 identified that at the same time RFC4960 states that
cwnd should never grow more than 1*MTU per RTT, Section 7.2.2 was
underspecified and as described could allow increasing cwnd more than
that.
This patch updates it so partial_bytes_acked is maxed to cwnd if
flight_size doesn't reach cwnd, protecting it from such case.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.26
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RFC4960 Errata 3.22, this condition is not needed anymore as it
could cause the partial_bytes_acked to not consider the TSNs acked in
the Gap Ack Blocks although they were received by the peer successfully.
This patch thus drops the check for new Cumulative TSN Ack Point,
leaving just the flight_size < cwnd one.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.22
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4960 Errata 3.12 says RFC4960 is unclear about the order of
adjustments applied to partial_bytes_acked and cwnd in the congestion
avoidance phase, and that the actual order should be:
partial_bytes_acked is reset to (partial_bytes_acked - cwnd). Next, cwnd
is increased by MTU.
We were first increasing cwnd, and then subtracting the new value pba,
which leads to a different result as pba is smaller than what it should
and could cause cwnd to not grow as much.
See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.12
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a bad thing not to handle errors when updating asoc. The memory
allocation failure in any of the functions called in sctp_assoc_update()
would cause sctp to work unexpectedly.
This patch is to fix it by aborting the asoc and reporting the error when
any of these functions fails.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
local_cork is used to decide if it should uncork asoc outq after processing
some cmds, and it is set when replying or sending msgs. local_cork should
always have the same value with current asoc q->cork in some way.
The thing is when changing to a new asoc by cmd SET_ASOC, local_cork may
not be consistent with the current asoc any more. The cmd seqs can be:
SCTP_CMD_UPDATE_ASSOC (asoc)
SCTP_CMD_REPLY (asoc)
SCTP_CMD_SET_ASOC (new_asoc)
SCTP_CMD_DELETE_TCB (new_asoc)
SCTP_CMD_SET_ASOC (asoc)
SCTP_CMD_REPLY (asoc)
The 1st REPLY makes OLD asoc q->cork and local_cork both are 1, and the cmd
DELETE_TCB clears NEW asoc q->cork and local_cork. After asoc goes back to
OLD asoc, q->cork is still 1 while local_cork is 0. The 2nd REPLY will not
set local_cork because q->cork is already set and it can't be uncorked and
sent out because of this.
To keep local_cork consistent with the current asoc q->cork, this patch is
to uncork the old asoc if local_cork is set before changing to the new one.
Note that the above cmd seqs will be used in the next patch when updating
asoc and handling errors in it.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now before dumping a sock in sctp_diag, it only holds the sock while
the ep may be already destroyed. It can cause a use-after-free panic
when accessing ep->asocs.
This patch is to set sctp_sk(sk)->ep NULL in sctp_endpoint_destroy,
and check if this ep is already destroyed before dumping this ep.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdrver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sctp_for_each_transport, pos is used to save how many objs it has
dumped. Now it gets the last obj by sctp_transport_get_idx, then gets
the next obj by sctp_transport_get_next.
The issue is that in the meanwhile if some objs in transport hashtable
are removed and the objs nums are less than pos, sctp_transport_get_idx
would return NULL and hti.walker.tbl is NULL as well. At this moment
it should stop hti, instead of continue getting the next obj. Or it
would cause a NULL pointer dereference in sctp_transport_get_next.
This patch is to pass pos + 1 into sctp_transport_get_idx to get the
next obj directly, even if pos > objs nums, it would return NULL and
stop hti.
Fixes: 626d16f50f ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the recently introduced helper to replace the pattern of
skb_put() && memset(), this transformation was done with the
following spatch:
@@
identifier p;
expression len;
expression skb;
@@
-p = skb_put(skb, len);
-memset(p, 0, len);
+p = skb_put_zero(skb, len);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_assoc_set_id does the assoc id check in the beginning when
processing dupcookie, no need to do the same check before calling
it.
v1->v2:
fix some typo errs Marcelo pointed in changelog.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to use read_lock_bh instead of local_bh_disable
and read_lock in sctp_eps_seq_show.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry got the following recursive locking report while running syzkaller
fuzzer, the Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x2ee/0x3ef lib/dump_stack.c:52
print_deadlock_bug kernel/locking/lockdep.c:1729 [inline]
check_deadlock kernel/locking/lockdep.c:1773 [inline]
validate_chain kernel/locking/lockdep.c:2251 [inline]
__lock_acquire+0xef2/0x3430 kernel/locking/lockdep.c:3340
lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
lock_sock_nested+0xcb/0x120 net/core/sock.c:2536
lock_sock include/net/sock.h:1460 [inline]
sctp_close+0xcd/0x9d0 net/sctp/socket.c:1497
inet_release+0xed/0x1c0 net/ipv4/af_inet.c:425
inet6_release+0x50/0x70 net/ipv6/af_inet6.c:432
sock_release+0x8d/0x1e0 net/socket.c:597
__sock_create+0x38b/0x870 net/socket.c:1226
sock_create+0x7f/0xa0 net/socket.c:1237
sctp_do_peeloff+0x1a2/0x440 net/sctp/socket.c:4879
sctp_getsockopt_peeloff net/sctp/socket.c:4914 [inline]
sctp_getsockopt+0x111a/0x67e0 net/sctp/socket.c:6628
sock_common_getsockopt+0x95/0xd0 net/core/sock.c:2690
SYSC_getsockopt net/socket.c:1817 [inline]
SyS_getsockopt+0x240/0x380 net/socket.c:1799
entry_SYSCALL_64_fastpath+0x1f/0xc2
This warning is caused by the lock held by sctp_getsockopt() is on one
socket, while the other lock that sctp_close() is getting later is on
the newly created (which failed) socket during peeloff operation.
This patch is to avoid this warning by use lock_sock with subclass
SINGLE_DEPTH_NESTING as Wang Cong and Marcelo's suggestion.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp holds read_lock when foreach sctp_ep_hashtable without disabling
BH. If CPU schedules to another thread A at this moment, the thread A may
be trying to hold the write_lock with disabling BH.
As BH is disabled and CPU cannot schedule back to the thread holding the
read_lock, while the thread A keeps waiting for the read_lock. A dead
lock would be triggered by this.
This patch is to fix this dead lock by calling read_lock_bh instead to
disable BH when holding the read_lock in sctp_for_each_endpoint.
Fixes: 626d16f50f ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRAM supply shortage and poor memory pressure tracking in TCP
stack makes any change in SO_SNDBUF/SO_RCVBUF (or equivalent autotuning
limits) and tcp_mem[] quite hazardous.
TCPMemoryPressures SNMP counter is an indication of tcp_mem sysctl
limits being hit, but only tracking number of transitions.
If TCP stack behavior under stress was perfect :
1) It would maintain memory usage close to the limit.
2) Memory pressure state would be entered for short times.
We certainly prefer 100 events lasting 10ms compared to one event
lasting 200 seconds.
This patch adds a new SNMP counter tracking cumulative duration of
memory pressure events, given in ms units.
$ cat /proc/sys/net/ipv4/tcp_mem
3088 4117 6176
$ grep TCP /proc/net/sockstat
TCP: inuse 180 orphan 0 tw 2 alloc 234 mem 4140
$ nstat -n ; sleep 10 ; nstat |grep Pressure
TcpExtTCPMemoryPressures 1700
TcpExtTCPMemoryPressuresChrono 5209
v2: Used EXPORT_SYMBOL_GPL() instead of EXPORT_SYMBOL() as David
instructed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since last patch, sctp doesn't need to alloc memory for asoc->stream any
more. sctp_stream_new and sctp_stream_init both are used to alloc memory
for stream.in or stream.out, and their names are also confusing.
This patch is to merge them into sctp_stream_init, and only pass stream
and streamcnt parameters into it, instead of the whole asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Marcelo's suggestion, stream is a fixed size member of asoc and would
not grow with more streams. To avoid an allocation for it, this patch is
to define it as an object instead of pointer and update the places using
it, also create sctp_stream_update() called in sctp_assoc_update() to
migrate the stream info from one stream to another.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
sometimes ICMP replies to INIT chunks are ignored by the client, even if
the encapsulated SCTP headers match an open socket. This happens when the
ICMP packet is carried by a paged skb: use skb_header_pointer() to read
packet contents beyond the SCTP header, so that chunk header and initiate
tag are validated correctly.
v2:
- don't use skb_header_pointer() to read the transport header, since
icmp_socket_deliver() already puts these 8 bytes in the linear area.
- change commit message to make specific reference to INIT chunks.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After sctp changed to use transport hashtable, a transport would be
added into global hashtable when adding the peer to an asoc, then
the asoc can be got by searching the transport in the hashtbale.
The problem is when processing dupcookie in sctp_sf_do_5_2_4_dupcook,
a new asoc would be created. A peer with the same addr and port as
the one in the old asoc might be added into the new asoc, but fail
to be added into the hashtable, as they also belong to the same sk.
It causes that sctp's dupcookie processing can not really work.
Since the new asoc will be freed after copying it's information to
the old asoc, it's more like a temp asoc. So this patch is to fix
it by setting it as a temp asoc to avoid adding it's any transport
into the hashtable and also avoid allocing assoc_id.
An extra thing it has to do is to also alloc stream info for any
temp asoc, as sctp dupcookie process needs it to update old asoc.
But I don't think it would hurt something, as a temp asoc would
always be freed after finishing processing cookie echo packet.
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3dbcc105d5 ("sctp: alloc stream info when initializing
asoc"), stream and stream.out info are always alloced when creating
an asoc.
So it's not correct to check !asoc->stream before updating stream
info when processing dupcookie, but would be better to check asoc
state instead.
Fixes: 3dbcc105d5 ("sctp: alloc stream info when initializing asoc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->csum_not_inet carries the indication on which algorithm is needed to
compute checksum on skb in the transmit path, when skb->ip_summed is equal
to CHECKSUM_PARTIAL. If skb carries a SCTP packet and crc32c hasn't been
yet written in L4 header, skb->csum_not_inet is assigned to 1; otherwise,
assume Internet Checksum is needed and thus set skb->csum_not_inet to 0.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_compute_checksum requires crc32c symbol (provided by libcrc32c), so
it can't be used in net core. Like it has been done previously with other
symbols (e.g. ipv6_dst_lookup), introduce a stub struct skb_checksum_ops
to allow computation of crc32c checksum in net core after sctp.ko (and thus
libcrc32c) has been loaded.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP needs fixes similar to 83eaddab43 ("ipv6/dccp: do not inherit
ipv6_mc_list from parent"), otherwise bad things can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ca50d12fe ("sctp: fix src address selection if using secondary
addresses") has fixed a src address selection issue when using secondary
addresses for ipv4.
Now sctp ipv6 also has the similar issue. When using a secondary address,
sctp_v6_get_dst tries to choose the saddr which has the most same bits
with the daddr by sctp_v6_addr_match_len. It may make some cases not work
as expected.
hostA:
[1] fd21:356b:459a:cf10::11 (eth1)
[2] fd21:356b:459a:cf20::11 (eth2)
hostB:
[a] fd21:356b:459a:cf30::2 (eth1)
[b] fd21:356b:459a:cf40::2 (eth2)
route from hostA to hostB:
fd21:356b:459a:cf30::/64 dev eth1 metric 1024 mtu 1500
The expected path should be:
fd21:356b:459a:cf10::11 <-> fd21:356b:459a:cf30::2
But addr[2] matches addr[a] more bits than addr[1] does, according to
sctp_v6_addr_match_len. It causes the path to be:
fd21:356b:459a:cf20::11 <-> fd21:356b:459a:cf30::2
This patch is to fix it with the same way as Marcelo's fix for sctp ipv4.
As no ip_dev_find for ipv6, this patch is to use ipv6_chk_addr to check
if the saddr is in a dev instead.
Note that for backwards compatibility, it will still do the addr_match_len
check here when no optimal is found.
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
This patch is to fix the replay attack issue for strreset asoc requests.
When a duplicated strreset asoc request is received, reply it with bad
seqno if it's seqno < asoc->strreset_inseq - 2, and reply it with the
result saved in asoc if it's seqno >= asoc->strreset_inseq - 2.
But note that if the result saved in asoc is performed, the sender's next
tsn and receiver's next tsn for the response chunk should be set. It's
safe to get them from asoc. Because if it's changed, which means the peer
has received the response already, the new response with wrong tsn won't
be accepted by peer.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the replay attack issue for strreset and addstrm in
requests.
When a duplicated strreset in or addstrm in request is received, reply it
with bad seqno if it's seqno < asoc->strreset_inseq - 2, and reply it with
the result saved in asoc if it's seqno >= asoc->strreset_inseq - 2.
For strreset in or addstrm in request, if the receiver side processes it
successfully, a strreset out or addstrm out request(as a response for that
request) will be sent back to peer. reconf_time will retransmit the out
request even if it's lost.
So when receiving a duplicated strreset in or addstrm in request and it's
result was performed, it shouldn't reply this request, but drop it instead.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp stream reconf will process a request again even if it's seqno is
less than asoc->strreset_inseq.
If one request has been done successfully and some data chunks have been
accepted and then a duplicated strreset out request comes, the streamin's
ssn will be cleared. It will cause that stream will never receive chunks
any more because of unsynchronized ssn. It allows a replay attack.
A similar issue also exists when processing addstrm out requests. It will
cause more extra streams being added.
This patch is to fix it by saving the last 2 results into asoc. When a
duplicated strreset out or addstrm out request is received, reply it with
bad seqno if it's seqno < asoc->strreset_inseq - 2, and reply it with the
result saved in asoc if it's seqno >= asoc->strreset_inseq - 2.
Note that it saves last 2 results instead of only last 1 result, because
two requests can be sent together in one chunk.
And note that when receiving a duplicated request, the receiver side will
still reply it even if the peer has received the response. It's safe, As
the response will be dropped by the peer.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when processing strreset out responses, it gets outreq->list_of_streams
only when result is performed. But if result is not performed, str_p will
be NULL. It will cause panic in sctp_ulpevent_make_stream_reset_event if
nums is not 0.
This patch is to fix it by getting outreq->list_of_streams earlier, and
also to improve some codes for the strreset inreq process.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp doesn't check sock's state before listening on it. It could
even cause changing a sock with any state to become a listening sock
when doing sctp_listen.
This patch is to fix it by checking sock's state in sctp_listen, so
that it will listen on the sock with right state.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is almost to revert commit 02f3d4ce9e ("sctp: Adjust PMTU
updates to accomodate route invalidation."). As t->asoc can't be NULL
in sctp_transport_update_pmtu, it could get sk from asoc, and no need
to pass sk into that function.
It is also to remove some duplicated codes from that function.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move sctp_transport_dst_check into sctp_packet_config
from sctp_packet_transmit and add pathmtu check in sctp_packet_config.
With this fix, sctp can update dst or pathmtu before appending chunks,
which can void dropping packets in sctp_packet_transmit when dst is
obsolete or dst's mtu is changed.
This patch is also to improve some other codes in sctp_packet_config.
It updates packet max_size with gso_max_size, checks for dst and
pathmtu, and appends ecne chunk only when packet is empty and asoc
is not NULL.
It makes sctp flush work better, as we only need to set up them once
for one flush schedule. It's also safe, since asoc is NULL only when
the packet is created by sctp_ootb_pkt_new in which it just gets the
new dst, no need to do more things for it other than set packet with
transport's pathmtu.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before when implementing sctp prsctp, SCTP_PR_STREAM_STATUS wasn't
added, as it needs to save abandoned_(un)sent for every stream.
After sctp stream reconf is added in sctp, assoc has structure
sctp_stream_out to save per stream info.
This patch is to add SCTP_PR_STREAM_STATUS by putting the prsctp
per stream statistics into sctp_stream_out.
v1->v2:
fix an indent issue.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since sctp reconf was added in sctp, the real cnt of in/out stream
have not been c.sinit_max_instreams and c.sinit_num_ostreams any
more.
This patch is to replace them with stream->in/outcnt.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a msg without asoc established, sctp will send INIT packet
first and then enqueue chunks.
Before receiving INIT_ACK, stream info is not yet alloced. But enqueuing
chunks needs to access stream info, like out stream state and out stream
cnt.
This patch is to fix it by allocing out stream info when initializing an
asoc, allocing in stream and re-allocing out stream when processing init.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Laight noticed the support for MSG_MORE with datamsg->force_delay
didn't really work as we expected, as the first msg with MSG_MORE set
would always block the following chunks' dequeuing.
This Patch is to rewrite it by saving the MSG_MORE flag into assoc as
David Laight suggested.
asoc->force_delay is used to save MSG_MORE flag before a msg is sent.
All chunks in queue would not be sent out if asoc->force_delay is set
by the msg with MSG_MORE flag, until a new msg without MSG_MORE flag
clears asoc->force_delay.
Note that this change would not affect the flush is generated by other
triggers, like asoc->state != ESTABLISHED, queue size > pmtu etc.
v1->v2:
Not clear asoc->force_delay after sending the msg with MSG_MORE flag.
Fixes: 4ea0c32f5f ("sctp: add support for MSG_MORE")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Laight <david.laight@aculab.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checking the return value of sk_busy_loop. As there are only a few
consumers of that data, and the data being checked for can be replaced
with a check for !skb_queue_empty() we might as well just pull the code
out of sk_busy_loop and place it in the spots that actually need it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the unnecessary temporary variable 'err' from
sctp_association_init.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the issue that sctp_prsctp_prune_sent forgot
to update q->out_qlen when removing a chunk from unsent queue.
Fixes: 8dbdf1f5b0 ("sctp: implement prsctp PRIO policy")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
