We shouldn't free things here because we free them later.
The call tree looks like this:
iser_connect() ==> initiating the connection establishment
and later
iser_cma_handler() => iser_route_handler() => iser_create_ib_conn_res()
if we fail here, eventually iser_conn_release() is called, resulting
in a double free.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The iser connection teardown flow isn't over until the underlying
Connection Manager (e.g the IB CM) delivers a disconnected or timeout
event through the RDMA-CM. When the remote (target) side isn't
reachable, e.g when some HW e.g port/hca/switch isn't functioning or
taken down administratively, the CM timeout flow is used and the event
may be generated only after relatively long time -- on the order of
tens of seconds.
The current iser code exposes this possibly long delay to higher
layers, specifically to the iscsid daemon and iscsi kernel stack. As a
result, the iscsi stack doesn't respond well: this low-level CM delay
is added to the fail-over time under HA schemes such as the one
provided by DM multipath through the multipathd(8) service.
This patch enhances the reference counting scheme on iser's IB
connections so that the disconnect flow initiated by iscsid from user
space (ep_disconnect) doesn't wait for the CM to deliver the
disconnect/timeout event. (The connection teardown isn't done from
iser's view point until the event is delivered)
The iser ib (rdma) connection object is destroyed when its reference
count reaches zero. When this happens on the RDMA-CM callback
context, extra care is taken so that the RDMA-CM does the actual
destroying of the associated ID, since doing it in the callback is
prohibited.
The reference count of iser ib connection normally reaches three,
where the <ref, deref> relations are
1. conn <init, terminate>
2. conn <bind, stop/destroy>
3. cma id <create, disconnect/error/timeout callbacks>
With this patch, multipath fail-over time is about 30 seconds, while
without this patch, multipath fail-over time is about 130 seconds.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The iscsi connection object life cycle includes binding and unbinding
(conn_stop) to/from the iscsi transport connection object. Since
iscsi connection objects are recycled, at the time the transport
connection (e.g iser's IB connection) is released, it is not valid to
touch the iscsi connection tied to the transport back-pointer since it
may already point to a different transport connection.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add handler to handle events such as port up and down. This is useful
when testing high-availability schemes such as multi-pathing.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Check correct variable for allocation failure
RDMA/nes: Correct cap.max_inline_data assignment in nes_query_qp()
RDMA/cm: Set num_paths when manually assigning path records
IB/cm: Fix device_create() return value check
The intent here is to check the "mfrpl->mapped_page_list" allocation.
We checked "mfrpl->ibfrpl.page_list" earlier.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cap.max_inline_data is incorrectly set in init_attr instead of attr.
Set it in attr so subsequent init_attr.cap assignment will get the
correct value.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When manually assigning the path records to use for a connection, save
the number of paths that were set. Otherwise, checks against num_path
will show 0, even though path record data is available.
This was discovered by manually setting the path records from user
space, then querying the kernel to see if the correct path records
were assigned, only to discover that the kernel returned 0 path
records to the query.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: numa: fix BUILD_BUG_ON for node_read_distance
driver-core: document ERR_PTR() return values
kobject: documentation: Update to refer to kset-example.c.
sysdev: the cpu probe/release attributes should be sysdev_class_attributes
kobject: documentation: Fix erroneous example in kobject doc.
driver-core: fix missing kernel-doc in firmware_class
Driver core: Early platform kernel-doc update
sysfs: fix sysfs lockdep warning in mlx4 code
sysfs: fix sysfs lockdep warning in infiniband code
sysfs: fix sysfs lockdep warning in ipmi code
sysfs: Initialised pci bus legacy_mem field before use
sysfs: use sysfs_bin_attr_init in firmware class driver
This fixes a sysfs lockdep warning in the infiniband code.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (69 commits)
[SCSI] scsi_transport_fc: Fix synchronization issue while deleting vport
[SCSI] bfa: Update the driver version to 2.1.2.1.
[SCSI] bfa: Remove unused header files and did some cleanup.
[SCSI] bfa: Handle SCSI IO underrun case.
[SCSI] bfa: FCS and include file changes.
[SCSI] bfa: Modified the portstats get/clear logic
[SCSI] bfa: Replace bfa_get_attr() with specific APIs
[SCSI] bfa: New portlog entries for events (FIP/FLOGI/FDISC/LOGO).
[SCSI] bfa: Rename pport to fcport in BFA FCS.
[SCSI] bfa: IOC fixes, check for IOC down condition.
[SCSI] bfa: In MSIX mode, ignore spurious RME interrupts when FCoE ports are in FW mismatch state.
[SCSI] bfa: Fix Command Queue (CPE) full condition check and ack CPE interrupt.
[SCSI] bfa: IOC recovery fix in fcmode.
[SCSI] bfa: AEN and byte alignment fixes.
[SCSI] bfa: Introduce a link notification state machine.
[SCSI] bfa: Added firmware save clear feature for BFA driver.
[SCSI] bfa: FCS authentication related changes.
[SCSI] bfa: PCI VPD, FIP and include file changes.
[SCSI] bfa: Fix to copy fpma MAC when requested by user space application.
[SCSI] bfa: RPORT state machine: direct attach mode fix.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix CX4 link problem in back-to-back configuration
RDMA/nes: Clear stall bit before destroying NIC QP
RDMA/nes: Set assume_aligned_header bit
RDMA/cxgb3: Wait at least one schedule cycle during device removal
IB/mad: Ignore iWARP devices on device removal
IPoIB: Include return code in trace message for ib_post_send() failures
IPoIB: Fix TX queue lockup with mixed UD/CM traffic
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
Commit 09124e19 ("RDMA/nes: Add support for KR device id 0x0110") took
out too much code and broke CX4 link detection in back-to-back
configuration. Put back the code that does the link check.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clear the stall bit to drop any incoming packets while destroying NIC
QP. This will prevent a chip resource leak.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set assume_aligned_header bit in QP context as requested by hardware group.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a hot-plug LLD removal event or an EEH error event, iw_cxgb3
must ensure that any/all threads that might be in a cxgb3 exported
function must return from the function before iw_cxgb3 returns from
its event processing. Do this by calling synchronize_net().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When an iWARP device is unloaded, the ib_mad module logs errors. It
should be ignoring iWARP devices on device removal just like it does
on device add.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Print the return code of ib_post_send() if it fails to make these
debugging messages more useful.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPoIB UD QP reports send completions to priv->send_cq, which is
usually left unarmed; it only gets armed when the number of
outstanding send requests reaches the size of the TX queue. This
arming is done only in the send path for the UD QP. However, when
sending CM packets, the net queue may be stopped for the same reasons
but no measures are taken to recover the UD path from a lockup.
Consider this scenario: a host sends high rate of both CM and UD
packets, with a TX queue length of N. If at some time the number of
outstanding UD packets is more than N/2 and the overall outstanding
packets is N-1, and CM sends a packet (making the number of
outstanding sends equal N), the TX queue will be stopped. When all
the CM packets complete, the number of outstanding packets will still
be higher than N/2 so the TX queue will not be restarted.
Fix this by calling ib_req_notify_cq() when the queue is stopped in
the CM path.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert some drivers who export a single string as class attribute
to the new class_attr_string functions. This removes redundant
code all over.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
This makes the class attributes the same as sysdev_class attributes
and plain attributes.
This will allow further cleanups in drivers.
Full tree sweep converting all users.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
init: Open /dev/console from rootfs
mqueue: fix typo "failues" -> "failures"
mqueue: only set error codes if they are really necessary
mqueue: simplify do_open() error handling
mqueue: apply mathematics distributivity on mq_bytes calculation
mqueue: remove unneeded info->messages initialization
mqueue: fix mq_open() file descriptor leak on user-space processes
fix race in d_splice_alias()
set S_DEAD on unlink() and non-directory rename() victims
vfs: add NOFOLLOW flag to umount(2)
get rid of ->mnt_parent in tomoyo/realpath
hppfs can use existing proc_mnt, no need for do_kern_mount() in there
Mirror MS_KERNMOUNT in ->mnt_flags
get rid of useless vfsmount_lock use in put_mnt_ns()
Take vfsmount_lock to fs/internal.h
get rid of insanity with namespace roots in tomoyo
take check for new events in namespace (guts of mounts_poll()) to namespace.c
Don't mess with generic_permission() under ->d_lock in hpfs
sanitize const/signedness for udf
nilfs: sanitize const/signedness in dealing with ->d_name.name
...
Fix up fairly trivial (famous last words...) conflicts in
drivers/infiniband/core/uverbs_main.c and security/tomoyo/realpath.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
IB/srp: Clean up error path in srp_create_target_ib()
IB/srp: Split send and recieve CQs to reduce number of interrupts
RDMA/nes: Add support for KR device id 0x0110
IB/uverbs: Use anon_inodes instead of private infinibandeventfs
IB/core: Fix and clean up ib_ud_header_init()
RDMA/cxgb3: Mark RDMA device with CXIO_ERROR_FATAL when removing
RDMA/cxgb3: Don't allocate the SW queue for user mode CQs
RDMA/cxgb3: Increase the max CQ depth
RDMA/cxgb3: Doorbell overflow avoidance and recovery
IB/core: Pack struct ib_device a little tighter
IB/ucm: Clean whitespace errors
IB/ucm: Increase maximum devices supported
IB/ucm: Use stack variable 'base' in ib_ucm_add_one
IB/ucm: Use stack variable 'devnum' in ib_ucm_add_one
IB/umad: Clean whitespace
IB/umad: Increase maximum devices supported
IB/umad: Use stack variable 'base' in ib_umad_init_port
IB/umad: Use stack variable 'devnum' in ib_umad_init_port
IB/umad: Remove port_table[]
IB/umad: Convert *cdev to cdev in struct ib_umad_port
...
The iscsi_eh_target_reset has been modified to attempt
target reset only. If it fails, then iscsi_eh_session_reset
will be called.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Instead of repeating the error unwinding steps in each place an error
can be detected, use the common idiom of gotos into an error flow.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We can reduce the number of IB interrupts from two interrupts per
srp_queuecommand() call to one by using separate CQs for send and
receive completions and processing send completions by polling every
time a TX IU is allocated.
Receive completion events still trigger an interrupt.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Apparently bogus mc address can break IPOIB multicast processing. Therefore
returning the check for addrlen back until this is resolved in bonding (I don't
see any other point from where mc address with non-dev->addr_len length can came
from).
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the loop complexicity in nes_nic.c, I'm using char* to copy mc addresses
to it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for KR device id 0x0110. While at it, cleanup
nes_init_phy() by splitting it into nes_init_1g_phy() and
nes_init_2025_phy().
Remove support for NES_PHY_TYPE_IRIS, which was used on an XFP board
that was only manufactured in small quantities and given out for evals
in even smaller quantities.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The anon_inodes interface has been split to allow creating a bare
(non-installed) file pointer and also extended to allow specifying
O_RDONLY in the flags. This makes it a suitable replacement for the
private "infinibandeventfs" pseudo-filesystem used by uverbs, and this
replacement saves a small chunk of boilerplate code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_ud_header_init() first clears header and then fills up the various
fields. Later on, it tests header->immediate_present, which it has
already cleared, so the condition is always false. Fix this by adding
an immediate_present parameter and setting header->immediate_present
as is done with grh_present. Also remove unused calculation of
header_len.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If cxgb3 calls the iw_cxgb3 t3cclient remove function due to a device
removal event, then the iwch device must be marked with CXIO_ERROR_FATAL
since the device below us is going away. Otherwise, we can get stuck in
a deadlock as RDMA ULPs try and deallocate objects (like MRs, QPs, etc).
So always mark the device with CXIO_ERROR_FATAL when removing.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only kernel mode CQs need the SW queue memory allocated. The SW queue
for user mode CQs is allocated in userspace by libcxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>