Add the mbigen msi interrupt controller bindings document.
This patch based on Mark Rutland's patch
https://lkml.org/lkml/2015/7/23/558
Signed-off-by: Ma Jun <majun258@huawei.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds a binding for the Wolfson WM8974 mono audio codec.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for the following device-tree and ACPI 5.1 DSD
properties in the goodix touchscreen driver:
- touchscreen-inverted-x: X axis is inverted (boolean)
- touchscreen-inverted-y: Y axis is inverted (boolean)
- touchscreen-swapped-x-y: X and Y axis are swapped (boolean)
These are necessary on tablets which have a display in portrait
format while the touchscreen is in landscape format, such as e.g.
the MSI Primo 81.
Signed-off-by: Karsten Merker <merker@debian.org>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Irina Tirdea <irina.tirdea@intel.com> (with ACPI DSD properties)
Tested-by: Aleksei Mamlin <mamlinav@gmail.com> (with device-tree properties)
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI/device tree). For devices
that do not have the gpio pins properly declared, the functionality
depending on these pins will not be available, but the device can still
be used with basic functionality.
For both device tree and ACPI, the interrupt gpio pin configuration is
read from the "irq-gpios" property and the reset pin configuration is
read from the "reset-gpios" property. For ACPI 5.1, named properties
can be specified using the _DSD section. This functionality will not be
available for devices that use indexed gpio pins declared in the _CRS
section (we need to provide backward compatibility with devices
that do not support using the interrupt gpio pin as output).
For ACPI, the pins can be specified using ACPI 5.1:
Device (STAC)
{
Name (_HID, "GDIX1001")
...
Method (_CRS, 0, Serialized)
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\I2C0",
0x00, ResourceConsumer, ,
)
GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
"\\I2C0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0
}
GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\I2C0", 0x00,
ResourceConsumer, ,
)
{
1
}
})
Return (RBUF)
}
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package (2) {"irq-gpios", Package() {^STAC, 0, 0, 0 }},
Package (2) {"reset-gpios", Package() {^STAC, 1, 0, 0 }},
...
}
}
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of being at the MAC level the reset gpio preperty is moved at the
PHY child node level. It is still managed by the MAC, but from the point
of view of the binding it make more sense to be part of the PHY node.
This commit also fixes a build errors if GPIOLIB is not selected.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amend the DT bindings to include the optional clock sources for the Baud
Rate Generator for External Clock (BRG), as found on some SCIF variants
and on HSCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend the DT bindings to include the optional external clock on
(H)SCI(F) and some SCIFA, where this pin can serve as a clock input,
depending on board wiring.
Clarify the use of the divided functional clock as a source for the
sampling clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add fallback compatibility strings for R-Car Gen1, Gen2, and Gen3.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As no platform defines an interface clock the SCI driver always falls
back to a clock named "peripheral_clk".
- On SH platforms that clock is the base clock for the SCI functional
clock and has the same frequency,
- On ARM platforms that clock doesn't exist, and clk_get() will return
the default clock for the device.
We can thus make the functional clock mandatory and drop the interface
clock.
EPROBE_DEFER is handled for clocks that may be referenced from DT (i.e.
"fck", and the deprecated "sci_ick").
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
[geert: Handle EPROBE_DEFER, reformat description, break long comment line]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This set of changes brings in a few more helpers for DSI support as well
as a couple of new drivers and support for some more simple panels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vV7Q
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.5-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v4.5-rc1
This set of changes brings in a few more helpers for DSI support as well
as a couple of new drivers and support for some more simple panels.
* tag 'drm/panel/for-4.5-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/panel: simple: Add QiaoDian qd43003c0-40
of: Add vendor prefix for QiaoDian Xianshi
drm/panel: add kernel doc for size attributes in panel_desc
drm/panel: simple: Add support for Kyocera TCG121XGLP panel
devicetree: add vendor prefix for Kyocera Corporation
drm/bridge: Remove gratuitous blank line
drm/bridge: dw-hdmi: Use dashes in filenames
drm/panel: Add Sharp LS043T1LE01 MIPI DSI panel
dt-bindings: Add Sharp LS043T1LE01 panel binding
drm/dsi: Add Turn On/Shutdown Peripheral command helpers
drm/panel: Add Panasonic VVX10F034N00 MIPI DSI panel
dt-bindings: Add Panasonic VVX10F034N00 panel binding
drm/panel: simple: Add support for Innolux G121X1-L03
drm/panel: simple: Add support for BOE TV080WUM-NL0
dt-bindings: Add BOE TV080WUM-NL0 panel binding
of: Add vendor prefix for BOE Technology Group
drm/dsi: Add a helper to get bits per pixel of MIPI DSI pixel format
On this board, the touchscreen, an ads7843, is not handled directly by
Linux but by a companion FPGA. This FPGA is memory-mapped and the IP
design is very similar to the mk712.
This commit adds the support for this IP.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use "qiaodian" as the vendor prefix for QiaoDian Xianshi Corporation in
device tree compatible strings.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Simply document new compatibility string.
As a previous patch adds a generic R-Car Gen2 compatibility string
there appears to be no need for a driver updates.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add fallback compatibility strings for R-Car Gen2 and Gen3.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This extends the documentation of compatibility strings a little to
include the SoC names.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The GIC bindings for the ARM11MPCore need to differentiate between
the GIC on the Test Chip and the one on the evaluation baseboard.
Split the binding in two and define new compatible-strings.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Kyocera TCG121XGLP panel is an XGA LCD TFT panel connected through
LVDS, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
KYO is the stock ticker symbol of Kyocera Corporation.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds support and documentation for the PMA8084 regulators
found on APQ8084 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support and documentation for the PM8916 regulators
found on MSM8916 platforms.
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves the qcom,smd-rpm.txt to the correct location and splits
out the smd and rpm documentation. In addition, a smd-rpm-regulator
document is added.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provides an options to use the ptp clock routed from the Altera FPGA
fabric. Instead of the defalt eosc1 clock connected to the ARM HPS core.
This setting affects all emacs in the core as the ptp clock is common.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_get_clk looks in clock-name property for matching clock.
the ptp_ref_clk property is ignored.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA driver needs to be passed a reference to an mdio bus. Typically
the mac is configured to use a fixed link but the mdio bus still needs
to be registered so that it con configure the switch.
This patch follows the same process as the altera tse ethernet driver for
creation of the mdio bus.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has fixes spread thru driver, notably among them
- edma fixes for recent edma DT changes which went into 4.4
- odd fixes for at_hdmac
- minor fixes on bc dma and mic dma
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r53B
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.4-rc6' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"This has fixes spread thru driver, notably among them:
- edma fixes for recent edma DT changes which went into 4.4
- odd fixes for at_hdmac
- minor fixes on bc dma and mic dma"
* tag 'dmaengine-fix-4.4-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: at_xdmac: fix at_xdmac_prep_dma_memcpy()
dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
dmaengine: mic_x100: add missing spin_unlock
dmaengine: bcm2835-dma: Convert to use DMA pool
dmaengine: at_xdmac: fix bad behavior in interleaved mode
dmaengine: at_xdmac: fix false condition for memset_sg transfers
dmaengine: at_xdmac: fix macro typo
Support hisilicon,hi6220-usb for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Etnaviv follows the same priciple as imx-drm to have a virtual
master device node to bind all the individual GPU cores together
into one DRM device.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
The physical display tied to the framebuffer may have regulators
providing power to it, such as power for LCDs or interface conversion
chips.
The number of regulators in use may vary, but the regulator supply
binding can not be a list. Instead just support any named regulator
supply properties under the device node. These should be properly
named to match the device schematics / design. The driver should
take care to go through them all.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allow to power down the PHY when
the network interface is no more used.
This reset can't be done at the PHY driver level. The PHY must be able to
answer the to the mii bus scan to let the kernel creating a PHY device.
The patch introduces a new optional property "phy-reset-gpios" inspired
from the one use for the FEC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an example for all elements of the Arizona extcon device tree
binding.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Update the device tree binding documentation to include documentation for
the wlf,micd-configs property that is used to specify the configurations
for headset polarity detection (CTIA / OTMP).
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
- Support runtime pm
. In case of most ARM SoC, each IP has each power domain which should be
controlled by each IP driver using runtime pm interface. So this patch
series makes each IP driver to control its own power domain when
drm dpms is requested.
- Support of_graph based dt binding for DP panel.
. This patch series adds of_graph based dt binding for DP panel.
And also it keeps backward compatibility. This includes dt binding
patch so I got Acked-by from Krzysztof Kozlowski who is a Exynos
SoC maintainer and from Rob Herring who is a device tree maintainer.
- Cleanup for Exynos DRM IPP enhancement.
. This patch series is a first step for enhancing existing IPP framework
which will integrate existing IPP functions with DRM KMS part so that
these can be transparent to userspace. For other portion of the patch
series, we will have more times for the review.]
* 'exynos-drm-next' of git://git.kernel.org:/pub/scm/linux/kernel/git/daeinki/drm-exynos: (29 commits)
drm/exynos: gem: remove old unused prototypes
drm/exynos: fimd: fix dma burst size setting for small plane size
drm/exynos: fix clipping when scaling is enabled
drm/exynos: mixer: use ratio precalculated in exynos_state
drm/exynos: add generic check for plane state
drm/exynos: introduce exynos_drm_plane_config structure
drm/exynos: mixer: enable video overlay plane only when VP is available
drm/exynos: mixer: use crtc->state->adjusted_mode instead of crtc->mode
drm/exynos: introduce exynos_drm_plane_state structure
drm/exynos: move dma_addr attribute from exynos plane to exynos fb
drm/exynos: exynos7-decon: remove excessive check
drm/exynos: rotator: convert to common clock framework
drm/exynos: gsc: add device tree support and remove usage of static mappings
drm/exynos: gsc: fix wrong pm_runtime state
drm/exynos: gsc: prepare and unprepare gsc clock
ARM: dts: Use OF graph for DP to panel connection in exynos5800-peach-pi
dt-bindings: exynos-dp: update ports node binding for panel
drm/exynos: dp: add of_graph dt binding support for panel
drm/exynos: decon: remove unused variables
drm/exynos: dsi: modify a error type when getting a node failed
...
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-12-11
Here's another set of Bluetooth & 802.15.4 patches for the 4.5 kernel:
- 6LoWPAN debugfs support
- New 802.15.4 driver for ADF7242 MAC IEEE802154
- Initial code for 6LoWPAN Generic Header Compression (GHC) support
- Refactor Bluetooth LE scan & advertising behind dedicated workqueue
- Cleanups to Bluetooth H:5 HCI driver
- Support for Toshiba Broadcom based Bluetooth controllers
- Use continuous scanning when establishing Bluetooth LE connections
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional property info needed for DSIv2 DT.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
List the clocks in the order that's used in DT. We don't have mdp/dsi
DT nodes for any SoC in upstream yet, but we align with the order
we intend to use.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Update DT bindings for mdp. We now have a more uniform and future-proof
set of compatible strings.
MDP5 bindings were missing. Add those and update details on the
clock-names properties.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
All users of QPACE have upgraded to QPACE2 so remove the Cell QPACE code.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Also, sort the properties alphabetically and make indentation
consistent. Wording largely taken from i2c-rk3x.txt, thanks guys!
Only "i2c-scl-internal-delay-ns" is new, the rest is used by two drivers
already and was documented in their driver binding documentation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds device tree support for exynos_drm_gsc. This patch
also fixed build issue on non-Exynos platforms, thus dependency on
!ARCH_MULTIPLATFORM can be now removed. The driver cannot be used
simultaneously with V4L2 Mem2Mem GScaller driver thought.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch updates a ports node binding for panel.
With this, dp node can have a ports node which describes
a remote endpoint node that can be connected to panel or bridge
node.
Changelog v2:
- remove unnecessary properties and numbering.
- update description about eDP device.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that was
just added in 4.4, or that has been broken for many years without anyone
noticing.
at91/sama5d2
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin
- fix incorrect clock input for SDIO
exynos
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx
- Fix vf610 SAI clock configuration bug which is discovered by
the newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx
- fix prototypes for readl/writel functions
ls2080a
- use little-endian register access for GPIO and SDHCI
omap
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa
- use PWM lookup table for all ezx machines
s3c24xx
- Remove incorrect __init annotation from s3c24xx cpufreq driver structures.
versatile
- fix PCI IRQ mapping on Versatile PB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fgEd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
Add support for PA gpio pin for controlling an external amplifier as used
on some Allwinner boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding document for Pistachio Internal DAC
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding document for Texas Instruments pcm3168a codec
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the devicetree binding for the cru on the rk3228 which quite similar
structured as previous clock controllers.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The patch adds the binding file for Freescale imx7d ADC driver.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for AMS iAQ-core continuous and pulsed VOC sensors.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MAX30100 is an heart rate and pulse oximeter sensor that works using
two LEDS of different wavelengths, and detecting the light reflected
back.
This patchset adds support for both IR and RED LED channels which can
be processed in userspace to determine heart rate and blood oxygen
levels.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Phy properties are expected to be found in the PHY OF node. However
this Micrel driver also allows them to be placed into the MAC OF node.
This is deprecated. Document it as such, and remove the example using
the deprecated method to prevent people copying it into new device
tree files.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO block on different QorIQ chips could have registers in different
endianess. Define the property to specify which endian is used by the
hardware.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The pinctrl of rk3228 is much the same as rk3288's, but
without pmu.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver has been sitting in the linux-zigbee[2] repository for a long
time. We updated it from time to time and made it available via our
github kernel repository. The Linux MAC802.15.4 support has improved a lot
since then. Thanks to all! So it’s finally time to upstream this driver.
The ADF7242 requires an add-on firmware for the automatic IEEE 802.15.4
operating modes. The firmware file is currently made available on the
ADF7242 wiki page here [1]
[1] http://wiki.analog.com/resources/tools-software/linux-drivers/networking-mac802154/adf7242
[2] http://sourceforge.net/p/linux-zigbee/kernel/ci/devel/tree/drivers/ieee802154/adf7242.c
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The H3 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compatibility strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas USB DMA Controller driver to follow this convention.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add device tree binding for NAND on the BCM6368.
The BCM6368 has a NAND interrupt register with combined status and enable
registers. It also requires a clock, so add an optional clock to the
common brcmnand binding.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The dynamic power consumption of a device is proportional to the
square of voltage (V) and the clock frequency (f). It can be expressed as
Pdyn = dynamic-power-coefficient * V^2 * f.
The coefficient represents the running time dynamic power consumption in
units of mw/MHz/uVolt^2 and can be used in the above formula to
calculate the dynamic power in mW.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All the users of the tda998x driver are component based and bind the
driver via the device graph method described in
Documentation/devicetree/bindings/graph.txt. Add the fact that the
'port' node is required to the bindings.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Merge two bindings for the same driver to together.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Fix a few typos and reword the description of the
'#qca,ddr-wb-channel-cells' property.
Signed-off-by: Alban Bedel <albeu@free.fr>
CC: trivial@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The existing device tree bindings assume that we are only trying to
describe a single address space with a device tree (for ARM, either
the Normal or the Secure world). Some uses for device tree need to
describe both Normal and Secure worlds in a single device tree. Add
documentation of how to do this, by adding extra properties which
describe when a device appears differently in the two worlds or when
it only appears in one of them.
The binding describes the general principles for adding new
properties describing the secure world, but for now we only need a
single new property, "secure-status", which can be used to annotate
devices to indicate that they are only visible in one of the two
worlds.
The primary expected use of this binding is for a virtual machine
like QEMU to describe the VM layout to a TrustZone aware firmware
(which would then use the secure-only devices itself, and pass the DT
on to a kernel running in the non-secure world, which ignores the
secure-only devices and uses the rest).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This company already provided some products, so add them to the
vendor prefix list.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Document device-tree bindings for the USB controller on older
OCTEON SOCs (OCTEON, OCTEON+).
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Rob Herring <robh@kernel.org>
SRAM bindings for various SoCs, using the mmio-sram genalloc
API, are spread over different places - per SoC vendor. Since all of
these are quite similar (they depend on mmio-sram) move them to a common
place.
Suggested-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Kukjin Kim <kgene@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Fix the incorrect interrupt documentation file path in binding docs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add onsemi,pca9654 which is also compatible with the nxp,pca9524 as it
is an 8bit expander with an interrupt output.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As noted here [1], there are potentially future conflicts if we try to
use MTD's "partitions" subnode to describe anything besides just the
fixed-in-the-device-tree partitions currently described in this
document. Particularly, there was a proposal to use this node for the
AFS parser too.
It can pose a (small) problem to try to differentiate the following
nodes:
// using binding as currently specified
partitions {
#address-cells = <x>;
#size-cells = <y>;
partition@0 {
...;
};
};
and
// proposed future binding
partitions {
compatible = "arm,arm-flash-structure";
};
It's especially difficult if other uses of this node start having
subnodes.
So, since the "partitions" node is new in v4.4, let's fixup the binding
before release so that it requires a compatible property, so it's much
clearer to distinguish. e.g.:
// proposed
partitions {
compatible = "fixed-partitions";
#address-cells = <x>;
#size-cells = <y>;
partition@0 {
...;
};
};
[1] Subject: "mtd: create a partition type device tree binding"
http://lkml.kernel.org/g/20151113220039.GA74382@google.comhttp://lists.infradead.org/pipermail/linux-mtd/2015-November/063355.htmlhttp://lists.infradead.org/pipermail/linux-mtd/2015-November/063364.html
Cc: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
This is the driver for the Powerventure PV88090 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 3566c5b277 ("PM / OPP: Create a directory for opp bindings")
renamed the file:
Documentation/devicetree/bindings/power/opp.txt
to
Documentation/devicetree/bindings/opp/opp.txt
leaving a dead link in cpufreq/arm_big_little_dt.txt.
The link points now to the good file.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
commit 3566c5b277 ("PM / OPP: Create a directory for opp bindings")
renamed the file:
Documentation/devicetree/bindings/power/opp.txt
to
Documentation/devicetree/bindings/opp/opp.txt
leaving a dead link in cpufreq/arm_big_little_dt.txt.
The link points now to the good file.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Renesas DIV6 clocks provide a single clock output. Hence make the
"clock-output-names" DT property optional instead of mandatory. In case
the DT property is omitted the DT node name will be used.
Rename the variable "name" to "clk_name" to make the code more similar
with fixed-factor-clock.c, and to avoid a conflict with a nested local
variable while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The video engine has its own special module clock, consisting of a clock
gate, configurable dividers, and a reset control.
On later (sun[68]i) families, the reset control is moved out of this
piece of hardware and grouped with reset controls of other peripherals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The H3 clock control unit is similar to the those of other sun8i family
members like the A23.
It adds a new bus gates clock similar to the simple gates, but with a
different parent clock for each single gate.
Some of the gates use the new AHB2 clock as parent, whose clock source
is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
is mostly based on Allwinner kernel source code.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Trivial patch to add Vivante Corporation to the list of
devicetree vendor prefixes.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
The A10/A20 share the same set of DRAM clock gates, which controls
direct memory access for some peripherals.
On the A10, bit 15 controls the system's DRAM clock output (possibly
to the DRAM chips), which we need to keep on.
On the A20 this has been moved to the DRAM controller, becoming a no-op.
However it is still listed in the user manual, so add it anyway.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On some devices the wake and enable pins of the pixcir touchscreen
controller are connected to gpios and these must be controlled by the
driver for the device to operate properly.
Signed-off-by: Sander Vermin <sander@vermin.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This updates the Arizona MFD device tree bindings to add the
Cirrus Logic CS47L24 and WM1831 codecs. Note that unlike all the
other codecs the DCVDD-supply and MICVDD-supply are mandatory.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A lot of Thanksgiving turkey leftovers accumulated, here goes:
1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg.
2) IDs for some new iwlwifi chips, from Oren Givon.
3) Fix rtlwifi lockups on boot, from Larry Finger.
4) Fix memory leak in fm10k, from Stephen Hemminger.
5) We have a route leak in the ipv6 tunnel infrastructure, fix from
Paolo Abeni.
6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim.
7) Wrong lockdep annotations in tcp md5 support, fix from Eric
Dumazet.
8) Work around some middle boxes which prevent proper handling of TCP
Fast Open, from Yuchung Cheng.
9) TCP repair can do huge kmalloc() requests, build paged SKBs
instead. From Eric Dumazet.
10) Fix msg_controllen overflow in scm_detach_fds, from Daniel
Borkmann.
11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from
Nikolay Aleksandrov.
12) Fix use after free in epoll with AF_UNIX sockets, from Rainer
Weikusat.
13) Fix double free in VRF code, from Nikolay Aleksandrov.
14) Fix skb leaks on socket receive queue in tipc, from Ying Xue.
15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian.
16) Fix clearing of persistent array maps in bpf, from Daniel
Borkmann.
17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq
early enough. From Eric Dumazet.
18) Fix out of bounds accesses in bpf array implementation when
updating elements, from Daniel Borkmann.
19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric
Dumazet.
20) When dumping proxy neigh entries, we have to accomodate NULL
device pointers properly, from Konstantin Khlebnikov.
21) SCTP doesn't release all ipv6 socket resources properly, fix from
Eric Dumazet.
22) Prevent underflows of sch->q.qlen for multiqueue packet
schedulers, also from Eric Dumazet.
23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey
Huang and Michael Chan.
24) Don't actively scan radar channels, from Antonio Quartulli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits)
net: phy: reset only targeted phy
bnxt_en: Setup uc_list mac filters after resetting the chip.
bnxt_en: enforce proper storing of MAC address
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
net: lpc_eth: remove irq > NR_IRQS check from probe()
net_sched: fix qdisc_tree_decrease_qlen() races
openvswitch: fix hangup on vxlan/gre/geneve device deletion
ipv4: igmp: Allow removing groups from a removed interface
ipv6: sctp: implement sctp_v6_destroy_sock()
arm64: bpf: add 'store immediate' instruction
ipv6: kill sk_dst_lock
ipv6: sctp: add rcu protection around np->opt
net/neighbour: fix crash at dumping device-agnostic proxy entries
sctp: use GFP_USER for user-controlled kmalloc
sctp: convert sack_needed and sack_generation to bits
ipv6: add complete rcu protection around np->opt
bpf: fix allocation warnings in bpf maps and integer overflow
mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
net: mvneta: enable setting custom TX IP checksum limit
net: mvneta: fix error path for building skb
...
The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Simply document new compatibility strings.
As a previous patch adds a generic R-Car Gen2 compatibility string
there appears to be no need for a driver updates.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fallback compatibility strings for R-Car Gen 2 & 3 SoC Families.
This is in keeping with the fallback scheme being adopted wherever appropriate
for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sun9i A80 introduces a new variant of the NMI controller. The registers
are reordered, but the functionality remains the same.
Add a new compatible string for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lkml.kernel.org/r/1449130813-22400-3-git-send-email-wens@csie.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The NMI controller is found in all Allwinner multi-core SoCs. It is not
limited to sun[67]i, nor is it always found in the "system controller"
block. On sun[68]i, it is in the RTC block, while on sun9i, it is in the
PRCM block.
Drop these 2 specific bits from the binding doc filename.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lkml.kernel.org/r/1449130813-22400-2-git-send-email-wens@csie.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.
This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a property to allow changing the default power-saving mode.
By default, at read raw the chip will activate and provide
one measurent, then it will shut itself down. However, the
chip can also work in "continuous" mode which may be more reliable
but is also more power consuming.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mcp3421 is the single channel variant of the mcp342x family and
can be supported by the mcp342x driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The R-Car H3 has two xHCI controllers. This SoC is compatible with
R-Car Gen2 SoCs, however this SoC doesn't need some specific registers
setting, and need a new firmware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car M2-N (r8a7793) xHCI controller.
This SoC is compatible with R-Car H2 (r8a7790) and R-Car M2-W (r8a7791).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CfCl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.5 cycle
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
The "cpus" clock is the clock for the embedded processor in the A80.
It is also part of the PRCM clock tree. This clock includes a pre-
divider on one of its inputs. For now we are using a custom clock
driver for it. In the future we may want to develop a generalized
driver for these types of clocks, which also includes the AHB clock
driver on sun[5678]i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds support for the PRCM apbs clock gates found on the
Allwinner A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Update the driver and binding for pm8994-mpp devices.
Cc: <devicetree@vger.kernel.org>
Cc: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the binding and driver for pm8994-gpio devices.
Cc: <devicetree@vger.kernel.org>
Cc: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration with
pinctrl framework for msm8996.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
[sboyd@codeaurora.org: Remove duplicate entries and enums]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Björn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver for the multimedia clock controller found on MSM8996
based devices. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the global clock controller found on MSM8996
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MSIOF in SH-Mobile AG5 (sh73a0) is handled fine by the existing driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simply document new compat strings.
There appears to be no need for a driver updates.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the new dedicated "lantiq,<chip>-pinctrl" compatible strings
to the devicetree bindings Documentation, where <chip> is one of "ase",
"danube", "xrx100", "xrx200" or "xrx300" and marks the "lantiq,pinctrl-xway",
"lantiq,pinctrl-ase" and "lantiq,pinctrl-xr9" compatible strings as DEPRECATED.
Signed-off-by: Martin Schiller <mschiller@tdt.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In eDMA the events are directly mapped to a DMA channel (for example DMA
event 14 can only be handled by DMA channel 14). If the memcpy is enabled
on the eDMA, there is a possibility that the crossbar driver would assign
DMA event number already allocated in eDMA for memcpy. Furthermore the
eDMA can be shared with DSP in which case the crossbar driver should also
avoid mapping xbar events to DSP used event numbers (or channels).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Renamed gpio controller's driver name from cygnus to iproc to make it
more generic so that all iProc based SoCs having the same gpio controller
could use this.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add ngpios property to the gpio controller's DT node so that controller
driver extracts total number of in-use gpio lines from DT and removes
dependency on driver.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull thermal management fixes from Zhang Rui:
"Specifics:
- several fixes and cleanups on Rockchip thermal drivers.
- add the missing support of RK3368 SoCs in Rockchip driver.
- small fixes on of-thermal, power_allocator, rcar driver, IMX, and
QCOM drivers, and also compilation fixes, on thermal.h, when thermal
is not selected"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
imx: thermal: use CPU temperature grade info for thresholds
thermal: fix thermal_zone_bind_cooling_device prototype
Revert "thermal: qcom_spmi: allow compile test"
thermal: rcar_thermal: remove redundant operation
thermal: of-thermal: Reduce log level for message when can't fine thermal zone
thermal: power_allocator: Use temperature reading from tz
thermal: rockchip: Support the RK3368 SoCs in thermal driver
thermal: rockchip: consistently use int for temperatures
thermal: rockchip: Add the sort mode for adc value increment or decrement
thermal: rockchip: improve the conversion function
thermal: rockchip: trivial: fix typo in commit
thermal: rockchip: better to compatible the driver for different SoCs
dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible
Add DT bindings documentation for the rk3288 crypto drivers.
Signed-off-by: Zain Wang <zain.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This binding describes LM3631 and LM3632 regulator properties.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add part numbers for APE6 and current set of R-Car Gen2 SoCs to the
IPMMU DT binding documentation. The example is also updated to show
how the generic compatible string may be used as fallback.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add devicetree bindings for HiSilicon SAS driver.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ASRC need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to ASRC registers
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPDIF need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to SPDIF registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ESAI need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to ESAI registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the incorrect interrupt documentation file path in binding docs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add time units of -ms (milliseconds) to wlf,micd-timeout.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Update the name for the second jack detection pin binding to be a little
less confusing.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
It would be better to name OPP nodes as opp@<opp-hz> as that will ensure
that multiple DT nodes don't contain the same frequency. Of course we
expect the writer to name the node with its opp-hz frequency and not any
other frequency.
And that will let the compile error out if multiple nodes are using the
same opp-hz frequency.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These aren't used until now by any DT files and wouldn't be used now as
we have a better scheme in place now, i.e. opp-property-<name>
properties.
Remove the (useless) binding without breaking ABI.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Depending on the version of hardware or its properties, which are only
known at runtime, various properties of the OPP can change. For example,
an OPP with frequency 1.2 GHz, may have different voltage/current
requirements based on the version of the hardware it is running on.
In order to not replicate the same OPP tables for varying values of all
such fields, this commit introduces the concept of opp-property-<name>.
The <name> can be chosen by the platform at runtime, and OPPs will be
initialized depending on that name string. Currently support is extended
for the following properties:
- opp-microvolt-<name>
- opp-microamp-<name>
If the name string isn't provided by the platform, or if it is provided
but doesn't match the properties present in the OPP node, we will fall
back to the original properties without the -<name> string, if they are
available.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We may want to enable only a subset of OPPs, from the bigger list of
OPPs, based on what version of the hardware we are running on. This
would enable us to not duplicate OPP tables for every version of the
hardware we support.
To enable that, this patch defines a new property 'opp-supported-hw'. It
can support any number of hierarchy levels of the versions the hardware
follows. And based on the selected hardware versions, we can pick only
the relevant OPPs at runtime.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add the devicetree binding for the cru on the rk3036 which quite similar
structured as previous clock controllers.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Some boards have a gpio line tied to the switch reset pin. Allow this
gpio to be retrieved from the device tree, and take the switch out of
reset before performing the probe.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the binding document of inno-rk3036
audio codec driver.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds device tree bindings for the Panasonic VVX10F034N00
WUXGA panel.
Signed-off-by: Werner Johansson <werner.johansson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The BOE TV080WUM-NL0 is an 8.0", 1200x1920 (WUXGA) TFT-LCD panel
connected using four DSI lanes.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
BOE Technology Group Co., Ltd. is a supplier of semiconductor display
technologies, products and services.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
[treding@nvidia.com: add commit message, fixup subject]
Signed-off-by: Thierry Reding <treding@nvidia.com>
cs-gpios isn't required with patch "spi: mediatek: single
device does not require cs_gpios", so modify the description.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates document devicetree bindings
to fix syntax error.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broadcom BCM63138 DSL SoCs have the same ARMPLL clocking infrastructure
as the Cygnus and iProc chips, add a dedicated compatible string and
document that the ARMPLL node is a valid node for this chip.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
a3af0c65("ASoC: ak4613: add single-end optional property for IN/OUT pins")
added IN/OUT pin single-end optional property, but it used "ak4613" as
vendor prefix. This patch fixup to asahi-kasei.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for the Powerventure PV88060 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The H3 has a usb-phy clk register which is similar to that of earlier
SoCs, but with support for a larger number of phys. So we can simply add
a new set of clk-data and a new compatible and be done with it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add additional bindings for both inverting the polarity of the jack
detection pins and allowing the use of a second jack detection pin. Note
that the second jack detection pin is hard wired in the chip so can only
be enabled through the binding, rather than a pin being specified.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add additional bindings to allow configuration of the system specific
microphone detection settings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Pull the supported chip names from drivers/mtd/devices/m25p80.c and stop
pointing readers to Linux code.
Also (although I see this habit repeated throughout the
Documentation/devicetree/bindings/ tree), stop using the title "driver"
in this file, when we're trying explicitly to describe hardware, not
software.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
The TPS65086 PMIC contains several regulators and a GPO controller.
Add bindings for the TPS65086 GPO controller.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch explains the occasion of "hisilcon,mdio" and
"hisilicon,hns-mdio" according to Arnd's comments.
and reformat it according to comments from Rob<robh@kernel.org>.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
reset-gpios is more clear than rst-gpio.
This change has been done as one atomic commit but it
does breaks compatability with older dtbs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide support for Sigma Designs Tango4 clock generator.
NOTE: This driver is incompatible with Tango3 clkgen.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[sboyd@codeaurora.org: Add kernel.h include for panic/sprintf]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RealView ARM11MPCore enables parity, eventmon and shared
override in the cache controller through its current boardfile,
but the code and DT bindings for the ARM L220 is currently
lacking the ability to set this up from DT. Add the required
bool parameters for parity and shared override, but keep
eventmon out of it: this should be enabled by the event
monitor code.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
rockchip,playback-channels: max playback channels, 8 channels default.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ak4613 IN/OUT pin can be selected as differential/single-end.
Default is differential, because it is register default settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet RESET is active low pin, i.e. system goes to
reset state when pin signal is low.
The previous implementeation was assuming the pin is configured as
'active high' in DTS. Changle the gpio handling code and DTS configuration
to 'active low'.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver can output Audio-clkout0/1/2/3,
but these are optional properties for each board.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The compatible value can be board-specific, not SoC-specific.
Add curly braces to indicate that the board type is optional.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a binding document for Imagination Technologies I2S input
controller
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a header file that defines the clock numbers for Tegra210. It is
meant to be included by device trees so that they can refer to the
clocks by symbolic name instead of numeric value.
Also add the device tree binding documentation which is largely the
same as for earlier generations of Tegra.
Extracted from a larger patch by Rhyland Klein <rklein@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds documentation of device tree bindings for the STM32 dma
controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add Samsung EXYNOS5410 SoC specific data to enable pinctrl
support for all platforms based on EXYNOS5410.
Signed-off-by: Hakjoo Kim <ruppi.kim@hardkernel.com>
[AF: Rebased onto Exynos5260, irq_chip consolidation, const'ification]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
[k.kozlowski: Rebased on current v4.3]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
Adding binding documentation for Texas Instruments ADS8688 ADC.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Martin Hundebøll <martin.hundeboll@prevas.dk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This commit add support for STMicroelectronics lis2dh12 accelerometer.
Datasheet for this device can be found here:
http://www.st.com/st-web-ui/static/active/en/resource/technical/
document/datasheet/DM00091513.pdf
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull more input updates from Dmitry Torokhov:
"An update to the tsc2005 driver that allows it to also support tsc2004
(basically the same controller, but uses i2c instead of spi bus), and
a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: parkbd - drop bogus __init from parkbd_allocate_serio()
Input: elantech - add Fujitsu Lifebook U745 to force crc_enabled
Input: tsc2004 - add support for tsc2004
Input: tsc200x-core - rename functions and variables
Input: tsc2005 - separate SPI and core functions
Sorry for the delay in this patch which was mostly caused by getting the
merger of the mpt2/mpt3sas driver, which was seen as an essential item of
maintenance work to do before the drivers diverge too much. Unfortunately,
this caused a compile failure (detected by linux-next), which then had to be
fixed up and incubated. In addition to the mpt2/3sas rework, there are
updates from pm80xx, lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc
and ufs plus an assortment of changes including some year 2038 issues, a fix
for a remove before detach issue in some drivers and a couple of other minor
issues.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWRnpiAAoJEDeqqVYsXL0MJd0IAIkNP1q/6ksMw/lam2UlbdxN
zFsFOIhGM3xLnBFehbCx7JW3cmybA7WC5jhMjaa1OeJmYHLpwbTzvVwrLs2l/0y1
/S+G0wwxROZfIKj/1EO3oKbSPCu9N3lStxOnmNXt5PSUEzAXrTqSNTtnMf2ZGh7j
bQxTWEJe+66GckgGw4ozTXJHWXqM/Zs/FsYjn2h/WzFhFv8utr7zRSzHMVjcqpLG
TK/Lt03hiTGqiignKrV9W6JzdGTWf2LGIsj/njgR0dxv59cNH8PrHIjZyknSBxgn
lblinsCjxDHWnP4BSfTi9MQG1lEiZiWO3Y6TKkKJTgxZ9M0Eitspc+cLOiJ1mpg=
=HvQf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...
This patchset attempts to new compatible for thermal founding
on RK3368 SoCs.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
- Add empty of_translate_address needed for HiSilicon network driver.
- Fix alignment requirements for CMA regions in DT.
- Fix booting on PPC systems which can't do WARN() early.
- Rename ak4554 binding doc from .c to .txt.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q7M4
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Add empty of_translate_address needed for HiSilicon network driver.
- Fix alignment requirements for CMA regions in DT.
- Fix booting on PPC systems which can't do WARN() early.
- Rename ak4554 binding doc from .c to .txt.
* tag 'devicetree-fixes-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Provide static inline function for of_translate_address if needed
drivers: of: of_reserved_mem: fixup the alignment with CMA setup
of: Print rather than WARN'ing when overlap check fails
dt-bindings: ak4554: extension should be .txt
Add device tree binding documentation for serial flash with
Mediatek serial flash controller
Signed-off-by: Bayi Cheng <bayi.cheng@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
[Brian: fixed up language]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This round contains a couple of new drivers for the Marvell Berlin
family of SoCs, various SoCs from Renesas and Broadcom as well as the
backlight PWM present on MediaTek SoCs.
Further existing drivers are extended to support a wider range of
hardware.
The remaining patches are minor fixes and cleanups across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gwbt
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This round contains a couple of new drivers for the Marvell Berlin
family of SoCs, various SoCs from Renesas and Broadcom as well as the
backlight PWM present on MediaTek SoCs.
Further existing drivers are extended to support a wider range of
hardware.
The remaining patches are minor fixes and cleanups across the board.
Note that one of the patches included in this pull request is against
arch/unicore32. I've included it here because I couldn't get a
response from Guan Xuetao and I consider the change low-risk.
Equivalent patches have been merged and tested in Samsung and PXA
trees. The goal is to finally get rid of legacy code paths that have
repeatedly been causing headaches"
* tag 'pwm/for-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (24 commits)
pwm: sunxi: Fix whitespace issue
pwm: sysfs: Make use of the DEVICE_ATTR_[RW][WO] macro's
pwm: sysfs: Remove unnecessary temporary variable
unicore32: nb0916: Use PWM lookup table
pwm: pwm-rcar: Revise the device tree binding document about compatible
pwm: Return -ENODEV if no PWM lookup match is found
pwm: sun4i: Add support for PWM controller on sun5i SoCs
pwm: Set enable state properly on failed call to enable
pwm: lpss: Add support for runtime PM
pwm: lpss: Add more Intel Broxton IDs
pwm: lpss: Support all four PWMs on Intel Broxton
pwm: lpss: Add support for multiple PWMs
pwm-pca9685: enable ACPI device found on Galileo Gen2
pwm: Add MediaTek display PWM driver support
dt-bindings: pwm: Add MediaTek display PWM bindings
pwm: tipwmss: Enable on TI DRA7x and AM437x
pwm: atmel-hlcdc: add sama5d2 SoC support.
pwm: Add Broadcom BCM7038 PWM controller support
Documentation: dt: add Broadcom BCM7038 PWM controller binding
pwm: Add support for R-Car PWM Timer
...
Pull thermal updates from Zhang Rui:
- Implement generic devfreq cooling mechanism through frequency
reduction for devices using devfreq. From Ørjan Eide and Javi
Merino.
- Introduce OMAP3 support on TI SoC thermal driver. From Pavel Mack
and Eduardo Valentin.
- A bounch of small fixes on devfreq_cooling, Exynos, IMX, Armada, and
Rockchip thermal drivers.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (24 commits)
thermal: exynos: Directly return 0 instead of using local ret variable
thermal: exynos: Remove unneeded semicolon
thermal: exynos: Use IS_ERR() because regulator cannot be NULL
thermal: exynos: Fix first temperature read after registering sensor
thermal: exynos: Fix unbalanced regulator disable on probe failure
devfreq_cooling: return on allocation failure
thermal: rockchip: support the sleep pinctrl state to avoid glitches in s2r
dt-bindings: rockchip-thermal: Add the pinctrl states in this document
thermal: devfreq_cooling: Make power a u64
thermal: devfreq_cooling: use a thermal_cooling_device for register and unregister
thermal: underflow bug in imx_set_trip_temp()
thermal: armada: Fix possible overflow in the Armada 380 thermal sensor formula
thermal: imx: register irq handler later in probe
thermal: rockhip: fix setting thermal shutdown polarity
thermal: rockchip: fix handling of invalid readings
devfreq_cooling: add trace information
thermal: Add devfreq cooling
PM / OPP: get the voltage for all OPPs
tools/thermal: tmon: use pkg-config also for CFLAGS
linux/thermal.h: rename KELVIN_TO_CELSIUS to DECI_KELVIN_TO_CELSIUS
...
