* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
The keypad matrix variable declaration is not matching
with structure variable keymap declared in keypad_matrix.h.
Due to this, following sparse warnings are generated with omap3_defconfig.
arch/arm/mach-omap2/board-devkit8000.c:223:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-devkit8000.c:223:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-devkit8000.c:223:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-ldp.c:107:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-ldp.c:107:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-ldp.c:107:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3evm.c:472:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3evm.c:472:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3evm.c:472:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-3430sdp.c:114:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-3430sdp.c:114:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-3430sdp.c:114:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-cm-t35.c:568:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-cm-t35.c:568:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-cm-t35.c:568:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3stalker.c:415:13: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3stalker.c:415:13: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3stalker.c:415:13: got int static [toplevel] *<noident>
This patch modifies the variable keymap declaration as per declaration in matrix_keymap structure.
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-input@vger.kernel.org
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch "omap: zoom: add mmc3/wl1271 device support" in the
wireless tree still uses .wires in struct omap2_hsmmc_info.
.wires has now been replaced with .caps in patch "omap: mmc:
extended to pass host capabilities from board file" in the
OMAP tree.
This causes linux-next as of 20101001 build to break as
below. Fix this.
CC arch/arm/mach-omap2/board-zoom-peripherals.o
arch/arm/mach-omap2/board-zoom-peripherals.c:217: error: unknown field 'wires' specified in initializer
make[1]: *** [arch/arm/mach-omap2/board-zoom-peripherals.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Initialize all omap-uarts for zoom boards. Now zoom_peripheral_init
will initialise all uarts for 3630. 3630sdp_board_init call
zoom_peripheral_init so we can now remove serial_init from 3630sdp
board init as zoom_peripheral_init now will do that the same.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ASoC Multi-Component Support moves some code from sound/soc/omap/zoom2.c into
arch/arm/mach-omap2/board-zoom2.c. However, that code should go to
board-zoom-peripherals.c instead as there is common code and registration
for zoom boards.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Lopez Cruz, Misael <x0052729@ti.com>
Cc: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add MMC3 support on ZOOM, which has the wl1271 device hardwired to.
The wl1271 is a 4-wire, 1.8V, embedded SDIO WLAN device with an
external IRQ line, and power-controlled by a GPIO-based fixed regulator.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a fixed regulator vmmc device to enable power control
of the wl1271 wlan device.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is useless, since in Zoom2/3 boards, the ports aren't even
physically accessible.
They must be explicitly initted in the board-zoom2.c, board-zoom3.c
and board-3630sdp.c files instead.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Remove the +x bit from a couple of source files
Signed-off-by: Andrew Clayton <andrew@digital-domain.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.
Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Changes for setting the padconf value for sys_nirq line which is
connected to T2 INTR1. This will fix the T2 keypad wakeup.
Signed-off-by: Lesly A M <x0080970@ti.com>
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Keys: 'right arrow', 'up arrow' and 'select' were mapped
wrongly. This patch corrects them.
This patch also adds one missing key present in the board,
currently I added it as 'unknown' key, as I am not able to
find proper description for this key.
One key entry (r: 7, c: 5) is present in the keymap, which
is really not present in the board, removing it.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.
This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the hsmmc zoom peripheral configuration to support:
Power saving mode
mmc2 8-bit support
Configure mmc2 as non removable
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3: zoom2/3: make MMC slot work again
Commit 12f8dfb56 accidentally broke MMC on zoom2/3.
The .vmmc1 field of zoom_twldata was deleted. Restoring it
allows the MMC slot to work again
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C-1 bus frequency on zoom2/zoom3/sdp3630 should be 2.4 MHz.
The speed is limited by TWL5030/GAIA; a higher speed could lead to errors
on the interface.
The maximum I2C speed depends on the system clock for GAIA:
2.2 MHz (sys-clk = 19.2 MHz)
2.4 MHz (sys-clk = 26 MHz)
2.9 MHz (sys-clk = 38.4 MHz)
For Zoom2/Zoom3/SDP3630 the system clock is 26Mhz
and hence choose 2.4Mhz for I2C1 bus speed
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace zoom2 with zoom name in board-zoom-peripherals.c file
and board-zoom-debugboard.c. Create mach/board-zoom.h.
This file has functions reused for boards: Zoom2/Zoom3/sdp3630.
Hence have all functions commonly named as zoom
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Split zoom2 board file into a base board file and a board-zoom-peripherals.c
file. That way the same peripherals file can be reused for zoom3 and sdp3630
in addition to zoom2.
Also remove unused struct omap_board_config_kernel entry.
NOTE: Keep the twl4030_madc_platform_data and twl4030_platform_data
entries in board-zoom2.c to avoid merge conflicts with the pending
patches in MFD tree. These entries will be removed later as a fix.
Following list shows the commonality across the three platforms and hence the
case for software reuse:
Peripheral zoom2 zoom3 sdp3630
---------------------------------------
Ethernet smsc smsc smc
NOR n/a n/a B
Onenand n/a n/a B
HDMI A A B (present on different i2c)
NAND A A A (same nand)
SDRAM A A A (same sdram)
Keypad A A A (same twl)
Camera A A A (same sensor can be mounted)
LCD Display A A A (same wvga display)
OPPs A A A (same chip feature)
Audio A A A (same audio via twl5030)
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
