It is possible that we will see another interrupt triggering at the same
time as the touchscreen interrupts so it's still worth checking other
possible sources. Almost all of the win from the fast path comes from only
needing to read the primary register and saving the I/O costs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to ease system integration provide a simulation of active high
IRQs on the GPIOs by polling the GPIO status when an IRQ is generated.
This isn't ideal on several fronts and will miss initially active IRQs in
the current implementation but it should work well for most cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
More annoying than usual as they're in the middle of a function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensure that we never have a window where we've handled an interrupt (and
therefore need to be notified of new events) but haven't yet told the
interrupt controller that this is the case (so any new events will be
discarded).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The GPIO IRQs aren't the first IRQs defined, we need to subtract the base
for the GPIOs as well to use them for array indexes.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use irq_allocate_desc() to get the IRQ range, which turns into a noop on
non-sparse systems. Since all existing users are non-sparse there should
be no compatibility issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x IRQ set_type() operation is doing a direct register write when
called but since set_type() is called with the bus lock held this isn't
legal and could cause deadlocks in the IRQ core.
Fix this by posting the updates into an array and syncing in the
bus_sync_unlock() callback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The fact that we can't actually raise any interrupts doesn't stop us
setting up the IRQs we're exporting. While this isn't actually going
to do anything it allows us to proceed further through device setup
during board bringup and avoids issues with the MFD core not letting
us suppress the configuration of IRQ resources.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x interrupt masking support is a much better match for the genirq
enable and disable operations than for the mask and unmask operations. The
latter are intended to used during interrupt handling for temporary changes
which isn't really practical on a slow bus. Convert the operations over to
match this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x interrupt controller provides reporting of the touchscreen
related interrupts in the primary interrupt status register as a
performance optimisation - use this to avoid reading the secondary
status registers for those interrupts.
For code simplicity and to avoid iterating over all interrupts we open
code for the two affected interrupt sources.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provide platform data allowing the system to set the /IRQ pin into
CMOS mode rather than the default open drain. The default value of
this platform data reflects the default hardware configuration so
there should be no change to existing users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x touchscreen interrupts need acknowledgement even when using
direct signals to the CPU (which don't go through the core) so leave
the acknowledgement up to the touchscreen driver for simplicity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x can generate wake events, some unconditionally, so flag
the primary IRQ as a wake source in order to help the CPU treat the
/IRQ signal appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Actually makes the code larger rathe rthan smaller but does provide some
isolation against core API changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver was originally tested with an additional patch which
made this unneeded but that patch had issuges and got lost on the
way to mainline, causing problems when the errors are reported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: stable@kernel.org
Ensure that the hardware has interrupts masked if we are not using
the interrupt controller on the WM831x by initialising the masks
before we check for the setup data required for the IRQ line. This
avoids signalling an unused IRQ line and improves the robustness
of checks that the IRQ is in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This was used by the old, pre-genirq IRQ implementation but is no
longer required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace the wm831x-local IRQ infrastructure with genirq, allowing access
to the diagnostic infrastructure of genirq and allowing us to implement
interrupt support for the GPIOs. The switchover is done within the
wm831x specific IRQ API, further patches will convert the individual
drivers to use genirq directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This avoids crashes when running without interrupt support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x includes an interrupt controller managing interrupts for
the various functions on the chip. This patch adds support for the
core interrupt block on the device.
Ideally this would be supported by genirq, particularly for the
GPIOs, but currently genirq is unable to cope with controllers on
interrupt driven buses so we cut'n'paste the generic interface.
Once genirq is able to cope chips like this it should be a case
of filing the prefixes off the code and redoing wm831x-irq.c to
move over.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
