Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the necessary capabilities in nl80211 to allow drivers to
assign a cookie to control port TX frames (returned via extack in
the netlink ACK message of the command) and then later report the
frame's status.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200508144202.7678-2-markus.theil@tu-ilmenau.de
[use extack cookie instead of explicit message, recombine patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may wish to report the RX frequency in units of
KHz. Provide cfg80211_rx_mgmt_khz() and wrap it with
cfg80211_rx_mgmt() so exisiting drivers which can't report
KHz anyway don't need to change. Add a similar wrapper for
cfg80211_report_obss_beacon() so the frequency units stay
somewhat consistent.
This doesn't actually change the nl80211 API yet.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-2-thomas@adapt-ip.com
[fix mac80211 calling the non-khz version of obss beacon report,
drop trace point name changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some bands (S1G) define channels centered on a non-integer
MHz. Give ieee80211_channel and cfg80211_chan_def a
freq_offset component where the final frequency can be
expressed as:
MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
Also provide some helper functions to do the frequency
conversion and test for equality.
Retain the existing interface to frequency and channel
conversion helpers, and expose new ones which handle
frequencies in units of KHz.
Some internal functions (net/wireless/chan.c) pass around
a frequency value. Convert these to units of KHz.
mesh, ibss, wext, etc. are currently ignored.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make some changes to the TID-config API:
* use u16 in nl80211 (only, and restrict to using 8 bits for now),
to avoid issues in the future if we ever want to use higher TIDs.
* reject empty TIDs mask (via netlink policy)
* change feature advertising to not use extended feature flags but
have own mechanism for this, which simplifies the code
* fix all variable names from 'tid' to 'tids' since it's a mask
* change to cfg80211_ name prefixes, not ieee80211_
* fix some minor docs/spelling things.
Change-Id: Ia234d464b3f914cdeab82f540e018855be580dce
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the new NL80211_CMD_SET_TID_CONFIG command to support
data TID specific configuration. Per TID configuration is
passed in the nested NL80211_ATTR_TID_CONFIG attribute.
This patch adds support to configure per TID noack policy
through the NL80211_TID_CONFIG_ATTR_NOACK attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-2-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE P802.11-REVmd/D3.0 adds support for protecting Beacon frames using
a new set of keys (BIGTK; key index 6..7) similarly to the way
group-addressed Robust Management frames are protected (IGTK; key index
4..5). Extend cfg80211 and nl80211 to allow the new BIGTK to be
configured. Add an extended feature flag to indicate driver support for
the new key index values to avoid array overflows in driver
implementations and also to indicate to user space when this
functionality is available.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-2-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 8c3ed7aa2b.
As Jouni points out, there's really no need for this, since the
RSN pre-authentication frames are normal data frames, not port
control frames (locally).
We can still revert this now since it hasn't actually gone beyond
-next.
Fixes: 8c3ed7aa2b ("nl80211: add src and dst addr attributes for control port tx/rx")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200224101910.b746e263287a.I9eb15d6895515179d50964dec3550c9dc784bb93@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using control port over nl80211 in AP mode with
pre-authentication, APs need to forward frames to other
APs defined by their MAC address. Before this patch,
pre-auth frames reaching user space over nl80211 control
port have no longer any information about the dest attached,
which can be used for forwarding to a controller or injecting
the frame back to a ethernet interface over a AF_PACKET
socket.
Analog problems exist, when forwarding pre-auth frames from
AP -> STA.
This patch therefore adds the NL80211_ATTR_DST_MAC and
NL80211_ATTR_SRC_MAC attributes to provide more context
information when forwarding.
The respective arguments are optional on tx and included on rx.
Therefore unaware existing software is not affected.
Software which wants to detect this feature, can do so
by checking against:
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_MAC_ADDRS
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200115125522.3755-1-markus.theil@tu-ilmenau.de
[split into separate cfg80211/mac80211 patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.
If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.
If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.
To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rework event_create_dir() to use an array of static data instead of
function pointers where possible.
The problem is that it would call the function pointer on module load
before parse_args(), possibly even before jump_labels were initialized.
Luckily the generated functions don't use jump_labels but it still seems
fragile. It also gets in the way of changing when we make the module map
executable.
The generated function are basically calling trace_define_field() with a
bunch of static arguments. So instead of a function, capture these
arguments in a static array, avoiding the function call.
Now there are a number of cases where the fields are dynamic (syscall
arguments, kprobes and uprobes), in which case a static array does not
work, for these we preserve the function call. Luckily all these cases
are not related to modules and so we can retain the function call for
them.
Also fix up all broken tracepoint definitions that now generate a
compile error.
Tested-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191111132458.342979914@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In nl80211.c there is a policy for all bands in NUM_NL80211_BANDS and
in trace.h there is a callback trace for multicast rates which is per
band in NUM_NL80211_BANDS. Both need to be extended for the new
NL80211_BAND_6GHZ.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-6-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_remain_on_channel_expired is used to notify userspace when
the remain on channel duration expired by sending an event. There is
no such equivalent to CMD_FRAME, where if offchannel and a duration
is provided, the card will go offchannel for that duration. Currently
there is no way for userspace to tell when that duration expired
apart from setting an independent timeout. This timeout is quite
erroneous as the kernel may not immediately send out the frame
because of scheduling or work queue delays. In testing, it was found
this timeout had to be quite large to accomidate any potential delays.
A better solution is to have the kernel send an event when this
duration has expired. There is already NL80211_CMD_FRAME_WAIT_CANCEL
which can be used to cancel a NL80211_CMD_FRAME offchannel. Using this
command matches perfectly to how NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL
works, where its both used to cancel and notify if the duration has
expired.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding support to allow mesh HWMP to measure link metrics on unexercised
direct mesh path by sending some data frames to other mesh points which
are not currently selected as a primary traffic path but only 1 hop away.
The absence of the primary path to the chosen node makes it necessary to
apply some form of marking on a chosen packet stream so that the packets
can be properly steered to the selected node for testing, and not by the
regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for IEEE 802.11-2016 "Extended Key ID for Individually
Addressed Frames".
Extend cfg80211 and nl80211 to allow pairwise keys to be installed for
Rx only, enable Tx separately and allow Key ID 1 for pairwise keys.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[use NLA_POLICY_RANGE() for NL80211_KEY_MODE]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This interface allows the host driver to offload OWE processing
to user space. This intends to support OWE (Opportunistic Wireless
Encryption) AKM by the drivers that implement SME but rely on the
user space for the cryptographic/OWE processing in AP mode. Such
drivers are not capable of processing/deriving the DH IE.
A new NL80211 command - NL80211_CMD_UPDATE_OWE_INFO is introduced
to send the request/event between the host driver and user space.
Driver shall provide the OWE info (MAC address and DH IE) of
the peer to user space for cryptographic processing of the DH IE
through the event. Accordingly, the user space shall update the
OWE info/DH IE to the driver.
Following is the sequence in AP mode for OWE authentication.
Driver passes the OWE info obtained from the peer in the
Association Request to the user space through the event
cfg80211_update_owe_info_event. User space shall process the
OWE info received and generate new OWE info. This OWE info is
passed to the driver through NL80211_CMD_UPDATE_OWE_INFO
request. Driver eventually uses this OWE info to send the
Association Response to the peer.
This OWE info in the command interface carries the IEs that include
PMKID of the peer if the PMKSA is still valid or an updated DH IE
for generating a new PMKSA with the peer.
Signed-off-by: Liangwei Dong <liangwei@codeaurora.org>
Signed-off-by: Sunil Dutt <usdutt@codeaurora.org>
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[remove policy initialization - no longer exists]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new "peer measurement" API, that can be used to measure
certain things related to a peer. Right now, only implement
FTM (flight time measurement) over it, but the idea is that
it'll be extensible to also support measuring the necessary
things to calculate e.g. angle-of-arrival for WiGig.
The API is structured to have a generic list of peers and
channels to measure with/on, and then for each of those a
set of measurements (again, only FTM right now) to perform.
Results are sent to the requesting socket, including a final
complete message.
Closing the controlling netlink socket will abort a running
measurement.
v3:
- add a bit to report "final" for partial results
- remove list keeping etc. and just unicast out the results
to the requester (big code reduction ...)
- also send complete message unicast, and as a result
remove the multicast group
- separate out struct cfg80211_pmsr_ftm_request_peer
from struct cfg80211_pmsr_request_peer
- document timeout == 0 if no timeout
- disallow setting timeout nl80211 attribute to 0,
must not include attribute for no timeout
- make MAC address randomization optional
- change num bursts exponent default to 0 (1 burst, rather
rather than the old default of 15==don't care)
v4:
- clarify NL80211_ATTR_TIMEOUT documentation
v5:
- remove unnecessary nl80211 multicast/family changes
- remove partial results bit/flag, final is sufficient
- add max_bursts_exponent, max_ftms_per_burst to capability
- rename "frames per burst" -> "FTMs per burst"
v6:
- rename cfg80211_pmsr_free_wdev() to cfg80211_pmsr_wdev_down()
and call it in leave, so the device can't go down with any
pending measurements
v7:
- wording fixes (Lior)
- fix ftm.max_bursts_exponent to allow having the limit of 0 (Lior)
v8:
- copyright statements
- minor coding style fixes
- fix error path leak
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This variable shadows something that gets generated inside
the tracing macros, which causes sparse to warn. Avoid it
so sparse output is more readable, even if it doesn't seem
to cause any trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There were supposed to be two blocks - one for each direction
cfg80211 <-> driver, clean up the code to restore that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow userspace to enable fine timing measurement responder
functionality with configurable lci/civic parameters in AP mode.
This can be done at AP start or changing beacon parameters.
A new EXT_FEATURE flag is introduced for drivers to advertise
the capability.
Also nl80211 API support for retrieving statistics is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
[remove unused cfg80211_ftm_responder_params, clarify docs,
move validation into policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current support in the 60GHz band is for channels 1-4.
Add support for channels 5 and 6.
This requires enlarging ieee80211_channel.center_freq from u16 to u32.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current implementation of cfg80211_rx_control_port assumed that the
caller could provide a contiguous region of memory for the control port
frame to be sent up to userspace. Unfortunately, many drivers produce
non-linear skbs, especially for data frames. This resulted in userspace
getting notified of control port frames with correct metadata (from
address, port, etc) yet garbage / nonsense contents, resulting in bad
handshakes, disconnections, etc.
mac80211 linearizes skbs containing management frames. But it didn't
seem worthwhile to do this for control port frames. Thus the signature
of cfg80211_rx_control_port was changed to take the skb directly.
nl80211 then takes care of obtaining control port frame data directly
from the (linear | non-linear) skb.
The caller is still responsible for freeing the skb,
cfg80211_rx_control_port does not take ownership of it.
Fixes: 6a671a50f8 ("nl80211: Add CMD_CONTROL_PORT_FRAME API")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[fix some kernel-doc formatting, add fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for exporting the mac80211 TXQ stats via nl80211 by
way of a nested TXQ stats attribute, as well as for configuring the
quantum and limits that were previously only changeable through debugfs.
This commit adds just the nl80211 API, a subsequent commit adds support to
mac80211 itself.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-03-31
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add raw BPF tracepoint API in order to have a BPF program type that
can access kernel internal arguments of the tracepoints in their
raw form similar to kprobes based BPF programs. This infrastructure
also adds a new BPF_RAW_TRACEPOINT_OPEN command to BPF syscall which
returns an anon-inode backed fd for the tracepoint object that allows
for automatic detach of the BPF program resp. unregistering of the
tracepoint probe on fd release, from Alexei.
2) Add new BPF cgroup hooks at bind() and connect() entry in order to
allow BPF programs to reject, inspect or modify user space passed
struct sockaddr, and as well a hook at post bind time once the port
has been allocated. They are used in FB's container management engine
for implementing policy, replacing fragile LD_PRELOAD wrapper
intercepting bind() and connect() calls that only works in limited
scenarios like glibc based apps but not for other runtimes in
containerized applications, from Andrey.
3) BPF_F_INGRESS flag support has been added to sockmap programs for
their redirect helper call bringing it in line with cls_bpf based
programs. Support is added for both variants of sockmap programs,
meaning for tx ULP hooks as well as recv skb hooks, from John.
4) Various improvements on BPF side for the nfp driver, besides others
this work adds BPF map update and delete helper call support from
the datapath, JITing of 32 and 64 bit XADD instructions as well as
offload support of bpf_get_prandom_u32() call. Initial implementation
of nfp packet cache has been tackled that optimizes memory access
(see merge commit for further details), from Jakub and Jiong.
5) Removal of struct bpf_verifier_env argument from the print_bpf_insn()
API has been done in order to prepare to use print_bpf_insn() soon
out of perf tool directly. This makes the print_bpf_insn() API more
generic and pushes the env into private data. bpftool is adjusted
as well with the print_bpf_insn() argument removal, from Jiri.
6) Couple of cleanups and prep work for the upcoming BTF (BPF Type
Format). The latter will reuse the current BPF verifier log as
well, thus bpf_verifier_log() is further generalized, from Martin.
7) For bpf_getsockopt() and bpf_setsockopt() helpers, IPv4 IP_TOS read
and write support has been added in similar fashion to existing
IPv6 IPV6_TCLASS socket option we already have, from Nikita.
8) Fixes in recent sockmap scatterlist API usage, which did not use
sg_init_table() for initialization thus triggering a BUG_ON() in
scatterlist API when CONFIG_DEBUG_SG was enabled. This adds and
uses a small helper sg_init_marker() to properly handle the affected
cases, from Prashant.
9) Let the BPF core follow IDR code convention and therefore use the
idr_preload() and idr_preload_end() helpers, which would also help
idr_alloc_cyclic() under GFP_ATOMIC to better succeed under memory
pressure, from Shaohua.
10) Last but not least, a spelling fix in an error message for the
BPF cookie UID helper under BPF sample code, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements the TX side of NL80211_CMD_CONTROL_PORT_FRAME.
Userspace provides the raw EAPoL frame using NL80211_ATTR_FRAME.
Userspace should also provide the destination address and the protocol
type to use when sending the frame. This is used to implement TX of
Pre-authentication frames. If CONTROL_PORT_ETHERTYPE_NO_ENCRYPT is
specified, then the driver will be asked not to encrypt the outgoing
frame.
A new EXT_FEATURE flag is introduced so that nl80211 code can check
whether a given wiphy has capability to pass EAPoL frames over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit also adds cfg80211_rx_control_port function. This is used
to generate a CMD_CONTROL_PORT_FRAME event out to userspace. The
conn_owner_nlportid is used as the unicast destination. This means that
userspace must specify NL80211_ATTR_SOCKET_OWNER flag if control port
over nl80211 routing is requested in NL80211_CMD_CONNECT,
NL80211_CMD_ASSOCIATE, NL80211_CMD_START_AP or IBSS/mesh join.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix return value of cfg80211_rx_control_port()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- fix trace_hfi1_ctxt_info() to pass large struct by reference instead of by value
- convert 'type array[]' tracepoint arguments into 'type *array',
since compiler will warn that sizeof('type array[]') == sizeof('type *array')
and later should be used instead
The CAST_TO_U64 macro in the later patch will enforce that tracepoint
arguments can only be integers, pointers, or less than 8 byte structures.
Larger structures should be passed by reference.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This interface allows the host driver to offload the authentication to
user space. This is exclusively defined for host drivers that do not
define separate commands for authentication and association, but rely on
userspace SME (e.g., in wpa_supplicant for the ~WPA_DRIVER_FLAGS_SME
case) for the authentication to happen. This can be used to implement
SAE without full implementation in the kernel/firmware while still being
able to use NL80211_CMD_CONNECT with driver-based BSS selection.
Host driver sends NL80211_CMD_EXTERNAL_AUTH event to start/abort
authentication to the port on which connect is triggered and status
of authentication is further indicated by user space to host
driver through the same command response interface.
User space entities advertise this capability through the
NL80211_ATTR_EXTERNAL_AUTH_SUPP flag in the NL80211_CMD_CONNECT request.
Host drivers shall look at this capability to offload the authentication.
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[add socket connection ownership check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both cfg80211_rx_mgmt and cfg80211_report_obss_beacon functions send
reports to userspace using NL80211_ATTR_RX_SIGNAL_DBM attribute w/o
any processing of their input signal values. Which means that in
order to match userspace tools expectations, input signal values
for those functions are supposed to be in dBm units.
This patch cleans up comments, variable names, and trace reports
for those functions, replacing confusing 'mBm' by 'dBm'.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add API for setting the PMK to the driver. For FT support, allow
setting also the PMK-R0 Name.
This can be used by drivers that support 4-Way handshake offload
while IEEE802.1X authentication is managed by upper layers.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[arend.vanspriel@broadcom.com: add WANT_1X_4WAY_HS attribute]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X docs a bit to
say that the device may require it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the SET CQM command's RSSI threshold attribute to accept any
number of thresholds as a sorted array. The API should be backwards
compatible so that if one s32 threshold value is passed, the old
mechanism is enabled. The netlink event generated is the same in both
cases.
cfg80211 handles an arbitrary number of RSSI thresholds but drivers have
to provide a method (set_cqm_rssi_range_config) that configures a range
set by a high and a low value. Drivers have to call back when the RSSI
goes out of that range and there's no additional event for each time the
range is reconfigured as there was with the current one-threshold API.
This method doesn't have a hysteresis parameter because there's no
benefit to the cfg80211 code from having the hysteresis be handled by
hardware/driver in terms of the number of wakeups. At the same time
it would likely be less consistent between drivers if offloaded or
done in the drivers.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nl80211_nan_dual_band_conf enumeration doesn't make much sense.
The default value is assigned to a bit, which makes it weird if the
default bit and other bits are set at the same time.
To improve this, get rid of NL80211_NAN_BAND_DEFAULT and add a wiphy
configuration to let the drivers define which bands are supported.
This is exposed to the userspace, which then can make a decision on
which band(s) to use. Additionally, rename all "dual_band" elements
to "bands", to make things clearer.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add functionality to update the connection parameters when in connected
state, so that driver/firmware uses the updated parameters for
subsequent roaming. This is for drivers that support internal BSS
selection and roaming. The new command does not change the current
association state, i.e., it can be used to update IE contents for future
(re)associations without causing an immediate disassociation or
reassociation with the current BSS.
This commit implements the required functionality for updating IEs for
(Re)Association Request frame only. Other parameters can be added in
future when required.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability to configure if an AP (and associated VLANs) will
do multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own MAC
address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[fix disabling, add better documentation & commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some NAN configuration paramaters may change during the operation of
the NAN device. For example, a user may want to update master preference
value when the device gets plugged/unplugged to the power.
Add API that allows to do so.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A NAN function can be either publish, subscribe or follow
up. Make all the necessary verifications and just pass the
request to the driver.
Allow the user space application that starts NAN to
forbid any other socket to add or remove functions.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows user space to start/stop NAN interface.
A NAN interface is like P2P device in a few aspects: it
doesn't have a netdev associated to it.
Add the new interface type and prevent operations that
can't be executed on NAN interface like scan.
Define several attributes that may be configured by user space
when starting NAN functionality (master preference and dual
band operation)
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends NL80211_CMD_CONNECT to allow the NL80211_ATTR_PREV_BSSID
attribute to be used similarly to way this was already allowed with
NL80211_CMD_ASSOCIATE. This allows user space to request reassociation
(instead of association) when already connected to an AP. This provides
an option to reassociate within an ESS without having to disconnect and
associate with the AP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement new functionality for aborting an ongoing scan.
Add NL80211_CMD_ABORT_SCAN to the nl80211 interface. After
aborting the scan, driver shall provide the scan status by
calling cfg80211_scan_done().
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[change command to take wdev instead of netdev so that it
can be used on p2p-device scans]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
