When ODP is enabled with IB_ACCESS_HUGETLB then the required pages
should be calculated based on the extent of the MR, which is rounded
to the nearest huge page alignment.
Fixes: d2183c6f19 ("RDMA/umem: Move page_shift from ib_umem to ib_odp_umem")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190815083834.9245-5-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
We need to check if we have CQEs pending before starting a poll loop,
as those could be the events we will be spinning for (and hence we'll
find none). This can happen if a CQE triggers an error, or if it is
found by eg an IRQ before we get a chance to find it through polling.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
One of the components in LiteON CL1 device has limitations that
can be encountered based upon boundary race conditions using the
nvme bus specific suspend to idle flow.
When this situation occurs the drive doesn't resume properly from
suspend-to-idle.
LiteON has confirmed this problem and fixed in the next firmware
version. As this firmware is already in the field, avoid running
nvme specific suspend to idle flow.
Fixes: d916b1be94 ("nvme-pci: use host managed power state for suspend")
Link: http://lists.infradead.org/pipermail/linux-nvme/2019-July/thread.html
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Charles Hyde <charles.hyde@dellteam.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 1b1031ca63 ("nvme: validate cntlid during controller initialisation")
introduced a validation for controllers with duplicate cntlid that runs
on nvme_init_subsystem(). The problem is that the validation relies on
ctrl->cntlid, and this value is assigned (from id_ctrl value) after the
call for nvme_init_subsystem() in nvme_init_identify() for non-fabrics
scenario. That leads to ctrl->cntlid always being 0 in case we have a
physical set of controllers in the same subsystem.
This patch fixes that by loading the discovered cntlid id_ctrl value into
ctrl->cntlid before the subsystem initialization, only for the non-fabrics
case. The patch was tested with emulated nvme devices (qemu) having two
controllers in a single subsystem. Without the patch, we couldn't make
it work failing in the duplicate check; when running with the patch, we
could see the subsystem holding both controllers.
For the fabrics case we see ctrl->cntlid has a more intricate relation
with the admin connect, so we didn't change that.
Fixes: 1b1031ca63 ("nvme: validate cntlid during controller initialisation")
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvme_state_set_live() making a path available triggers requeue_work
in order to resubmit requests that ended up on requeue_list when no
paths were available.
This requeue_work may race with concurrent nvme_ns_head_make_request()
that do not observe the live path yet.
Such concurrent requests may by made by either:
- New IO submission.
- Requeue_work triggered by nvme_failover_req() or another ana_work.
A race may cause requeue_work capture the state of requeue_list before
more requests get onto the list. These requests will stay on the list
forever unless requeue_work is triggered again.
In order to prevent such race, nvme_state_set_live() should
synchronize_srcu(&head->srcu) before triggering the requeue_work and
prevent nvme_ns_head_make_request referencing an old snapshot of the
path list.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If a request issue ends up being punted to async context to avoid
blocking, we can get into a situation where the original application
enters the poll loop for that very request before it has been issued.
This should not be an issue, except that the polling will hold the
io_uring uring_ctx mutex for the duration of the poll. When the async
worker has actually issued the request, it needs to acquire this mutex
to add the request to the poll issued list. Since the application
polling is already holding this mutex, the workqueue sleeps on the
mutex forever, and the application thus never gets a chance to poll for
the very request it was interested in.
Fix this by ensuring that the polling drops the uring_ctx occasionally
if it's not making any progress.
Reported-by: Jeffrey M. Birnbaum <jmbnyc@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the case of X86_PAE, unsigned long is u32, but the physical address type
should be u64. Due to the bug here, the netvsc driver can not load
successfully, and sometimes the VM can panic due to memory corruption (the
hypervisor writes data to the wrong location).
Fixes: 6ba34171bc ("Drivers: hv: vmbus: Remove use of slow_virt_to_phys()")
Cc: stable@vger.kernel.org
Cc: Michael Kelley <mikelley@microsoft.com>
Reported-and-tested-by: Juliana Rodrigueiro <juliana.rodrigueiro@intra2net.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
When building hv_kvp_daemon GCC-8.3 complains:
hv_kvp_daemon.c: In function ‘kvp_get_ip_info.constprop’:
hv_kvp_daemon.c:812:30: warning: ‘ip_buffer’ may be used uninitialized in this function [-Wmaybe-uninitialized]
struct hv_kvp_ipaddr_value *ip_buffer;
this seems to be a false positive: we only use ip_buffer when
op == KVP_OP_GET_IP_INFO and it is only unset when op == KVP_OP_ENUMERATE.
Silence the warning by initializing ip_buffer to NULL.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Simplify the ring buffer handling with the in-place API.
Also avoid the dynamic allocation and the memory leak in the channel
callback function.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This field is no longer used after the commit
63ed4e0c67 ("Drivers: hv: vmbus: Consolidate all Hyper-V specific clocksource code")
, because it's replaced by the global variable
"struct ms_hyperv_tsc_page *tsc_pg;" (now, the variable is in
drivers/clocksource/hyperv_timer.c).
Fixes: 63ed4e0c67 ("Drivers: hv: vmbus: Consolidate all Hyper-V specific clocksource code")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The static structures ht16k33_fb_fix and ht16k33_fb_var, of types
fb_fix_screeninfo and fb_var_screeninfo respectively, are not used
except to be copied into other variables. Hence make both of them
constant to prevent unintended modification.
Issue found with
Coccinelle.
Acked-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
The EKR ring claims a range of 0 to 71 but actually reports
values 1 to 72. The ring is used in relative mode so this
change should not affect users.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Fixes: 72b236d602 ("HID: wacom: Add support for Express Key Remote.")
Cc: <stable@vger.kernel.org> # v4.3+
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need to provide the arch hooks for non-coherent dma-direct
and swiotlb for all swiotlb builds, not just when LPAS is enabled.
Without that the Xen build that selects SWIOTLB indirectly through
SWIOTLB_XEN fails to build.
Fixes: ad3c7b18c5 ("arm: use swiotlb for bounce buffering on LPAE configs")
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Stefan Wahren <wahrenst@gmx.net>
When SCSI-MQ is enabled, the SCSI-MQ layers will do pre-allocation of MQ
resources based on shost values set by the driver. In newer cases of the
driver, which attempts to set nr_hw_queues to the cpu count, the
multipliers become excessive, with a single shost having SCSI-MQ
pre-allocation reaching into the multiple GBytes range. NPIV, which
creates additional shosts, only multiply this overhead. On lower-memory
systems, this can exhaust system memory very quickly, resulting in a system
crash or failures in the driver or elsewhere due to low memory conditions.
After testing several scenarios, the situation can be mitigated by limiting
the value set in shost->nr_hw_queues to 4. Although the shost values were
changed, the driver still had per-cpu hardware queues of its own that
allowed parallelization per-cpu. Testing revealed that even with the
smallish number for nr_hw_queues for SCSI-MQ, performance levels remained
near maximum with the within-driver affiinitization.
A module parameter was created to allow the value set for the nr_hw_queues
to be tunable.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The parens used in the while loop would result in error being assigned
the value 1 rather than the intended errno value.
This is required to return -ETXTBSY from follow on break_layout()
changes.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
handful of samsung clk driver fixes for audio and display clks, and a
small fix for the Stratix10 SoC driver that was checking the wrong
register for validity.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAl1bI8sRHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSWJYRAAsaZUCBcuLpHXRBZDnO2/wWRQMxcl5yFi
PDyaSfhqJ8M7IQJZ2pLY9eImVfKwzfJ0Xes2fMw5xAqVJsiXoRPgwEP1SuigTvEt
qB9Ao3lXZkl37B5Hc/gKS/2xeDAdZfaAGE9ZwxYvVs38kikbBpxdOl8pTQbC8unt
Cr6Ay+Gxh20FTDR68ug3jkWOtg3NfLMoM/Ynu+0WwAzsESGfcBZhOJRp50jaqe51
d+jO3YkUU5tA/YcJrJM5PWyZDb5EK2ONUcr7Em+/MvJlz80rPgdkwLGYz+5fgJBz
QtDp664Gxaq+Uqq8GW/Uz+zvkoEnFKWbyAxXMwRHwDLVzaPO0Nm0LKFPLRcRNOuL
qYe6hB+MekDelmeBoVYQ7JQEiPdZx5i9JcldZase+5hUzr5co1SVfl84LTz3il6d
JJdm/PBv0AXQJXg39H3zcbbjEtVzfOI7FZqTLiruxm9wkT7kRyEcj5BB9zpIMEY1
4MatzJL5uiZnAuPA3BA/FB/5lK6bJu6arIdRK4pXRYZvvw5gEvGBJCCvA6pY+z6n
iqPazWPcyRIiBon2o3UqRkZxBeiKhfsXyeNNq15jQh7pq7W+D6r+G/NSbV5hv2Ji
OeqXV/zhdIfYayfJXzpSxiLYaNDq+qPn0AWLPcm35Sj5wfOZKM3jg6ZFkPgaq6n8
kr7r417ixuc=
=1qKh
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A couple fixes to the core framework logic that finds clk parents, a
handful of samsung clk driver fixes for audio and display clks, and a
small fix for the Stratix10 SoC driver that was checking the wrong
register for validity"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Fix potential NULL dereference in clk_fetch_parent_index()
clk: Fix falling back to legacy parent string matching
clk: socfpga: stratix10: fix rate caclulationg for cnt_clks
clk: samsung: exynos542x: Move MSCL subsystem clocks to its sub-CMU
clk: samsung: exynos5800: Move MAU subsystem clocks to MAU sub-CMU
clk: samsung: Change signature of exynos5_subcmus_init() function
Pull kernel thread signal handling fix from Eric Biederman:
"I overlooked the fact that kernel threads are created with all signals
set to SIG_IGN, and accidentally caused a regression in cifs and drbd
when replacing force_sig with send_sig.
This is my fix for that regression. I add a new function
allow_kernel_signal which allows kernel threads to receive signals
sent from the kernel, but continues to ignore all signals sent from
userspace. This ensures the user space interface for cifs and drbd
remain the same.
These kernel threads depend on blocking networking calls which block
until something is received or a signal is pending. Making receiving
of signals somewhat necessary for these kernel threads.
Perhaps someday we can cleanup those interfaces and remove
allow_kernel_signal. If not allow_kernel_signal is pretty trivial and
clearly documents what is going on so I don't think we will mind
carrying it"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Allow cifs and drbd to receive their terminating signals
If alloc_descs() fails before irq_sysfs_init() has run, free_desc() in the
cleanup path will call kobject_del() even though the kobject has not been
added with kobject_add().
Fix this by making the call to kobject_del() conditional on whether
irq_sysfs_init() has run.
This problem surfaced because commit aa30f47cf6 ("kobject: Add support
for default attribute groups to kobj_type") makes kobject_del() stricter
about pairing with kobject_add(). If the pairing is incorrrect, a WARNING
and backtrace occur in sysfs_remove_group() because there is no parent.
[ tglx: Add a comment to the code and make it work with CONFIG_SYSFS=n ]
Fixes: ecb3f394c5 ("genirq: Expose interrupt information through sysfs")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1564703564-4116-1-git-send-email-mikelley@microsoft.com
There have been reports of RDRAND issues after resuming from suspend on
some AMD family 15h and family 16h systems. This issue stems from a BIOS
not performing the proper steps during resume to ensure RDRAND continues
to function properly.
RDRAND support is indicated by CPUID Fn00000001_ECX[30]. This bit can be
reset by clearing MSR C001_1004[62]. Any software that checks for RDRAND
support using CPUID, including the kernel, will believe that RDRAND is
not supported.
Update the CPU initialization to clear the RDRAND CPUID bit for any family
15h and 16h processor that supports RDRAND. If it is known that the family
15h or family 16h system does not have an RDRAND resume issue or that the
system will not be placed in suspend, the "rdrand=force" kernel parameter
can be used to stop the clearing of the RDRAND CPUID bit.
Additionally, update the suspend and resume path to save and restore the
MSR C001_1004 value to ensure that the RDRAND CPUID setting remains in
place after resuming from suspend.
Note, that clearing the RDRAND CPUID bit does not prevent a processor
that normally supports the RDRAND instruction from executing it. So any
code that determined the support based on family and model won't #UD.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chen Yu <yu.c.chen@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: "linux-doc@vger.kernel.org" <linux-doc@vger.kernel.org>
Cc: "linux-pm@vger.kernel.org" <linux-pm@vger.kernel.org>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: <stable@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "x86@kernel.org" <x86@kernel.org>
Link: https://lkml.kernel.org/r/7543af91666f491547bd86cebb1e17c66824ab9f.1566229943.git.thomas.lendacky@amd.com
Pull networking fixes from David Miller:
1) Fix jmp to 1st instruction in x64 JIT, from Alexei Starovoitov.
2) Severl kTLS fixes in mlx5 driver, from Tariq Toukan.
3) Fix severe performance regression due to lack of SKB coalescing of
fragments during local delivery, from Guillaume Nault.
4) Error path memory leak in sch_taprio, from Ivan Khoronzhuk.
5) Fix batched events in skbedit packet action, from Roman Mashak.
6) Propagate VLAN TX offload to hw_enc_features in bond and team
drivers, from Yue Haibing.
7) RXRPC local endpoint refcounting fix and read after free in
rxrpc_queue_local(), from David Howells.
8) Fix endian bug in ibmveth multicast list handling, from Thomas
Falcon.
9) Oops, make nlmsg_parse() wrap around the correct function,
__nlmsg_parse not __nla_parse(). Fix from David Ahern.
10) Memleak in sctp_scend_reset_streams(), fro Zheng Bin.
11) Fix memory leak in cxgb4, from Wenwen Wang.
12) Yet another race in AF_PACKET, from Eric Dumazet.
13) Fix false detection of retransmit failures in tipc, from Tuong
Lien.
14) Use after free in ravb_tstamp_skb, from Tho Vu.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
ravb: Fix use-after-free ravb_tstamp_skb
netfilter: nf_tables: map basechain priority to hardware priority
net: sched: use major priority number as hardware priority
wimax/i2400m: fix a memory leak bug
net: cavium: fix driver name
ibmvnic: Unmap DMA address of TX descriptor buffers after use
bnxt_en: Fix to include flow direction in L2 key
bnxt_en: Use correct src_fid to determine direction of the flow
bnxt_en: Suppress HWRM errors for HWRM_NVM_GET_VARIABLE command
bnxt_en: Fix handling FRAG_ERR when NVM_INSTALL_UPDATE cmd fails
bnxt_en: Improve RX doorbell sequence.
bnxt_en: Fix VNIC clearing logic for 57500 chips.
net: kalmia: fix memory leaks
cx82310_eth: fix a memory leak bug
bnx2x: Fix VF's VLAN reconfiguration in reload.
Bluetooth: Add debug setting for changing minimum encryption key size
tipc: fix false detection of retransmit failures
lan78xx: Fix memory leaks
MAINTAINERS: r8169: Update path to the driver
MAINTAINERS: PHY LIBRARY: Update files in the record
...
The maximum key description size is 4095. Commit f771fde820 ("keys:
Simplify key description management") inadvertantly reduced that to 255
and made sizes between 256 and 4095 work weirdly, and any size whereby
size & 255 == 0 would cause an assertion in __key_link_begin() at the
following line:
BUG_ON(index_key->desc_len == 0);
This can be fixed by simply increasing the size of desc_len in struct
keyring_index_key to a u16.
Note the argument length test in keyutils only checked empty
descriptions and descriptions with a size around the limit (ie. 4095)
and not for all the values in between, so it missed this. This has been
addressed and
https://git.kernel.org/pub/scm/linux/kernel/git/dhowells/keyutils.git/commit/?id=066bf56807c26cd3045a25f355b34c1d8a20a5aa
now exhaustively tests all possible lengths of type, description and
payload and then some.
The assertion failure looks something like:
kernel BUG at security/keys/keyring.c:1245!
...
RIP: 0010:__key_link_begin+0x88/0xa0
...
Call Trace:
key_create_or_update+0x211/0x4b0
__x64_sys_add_key+0x101/0x200
do_syscall_64+0x5b/0x1e0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
It can be triggered by:
keyctl add user "aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa" a @s
Fixes: f771fde820 ("keys: Simplify key description management")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BIOS on Samsung 500C Chromebook reports very rudimentary E820 table that
consists of 2 entries:
BIOS-e820: [mem 0x0000000000000000-0x0000000000000fff] usable
BIOS-e820: [mem 0x00000000fffff000-0x00000000ffffffff] reserved
It breaks logic in find_trampoline_placement(): bios_start lands on the
end of the first 4k page and trampoline start gets placed below 0.
Detect underflow and don't touch bios_start for such cases. It makes
kernel ignore E820 table on machines that doesn't have two usable pages
below BIOS_START_MAX.
Fixes: 1b3a626436 ("x86/boot/compressed/64: Validate trampoline placement against E820")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203463
Link: https://lkml.kernel.org/r/20190813131654.24378-1-kirill.shutemov@linux.intel.com
When calling request_threaded_irq() with a CP2112, the function
cp2112_gpio_irq_startup() is called in a IRQ context.
Therefore we can not sleep, and we can not call
cp2112_gpio_direction_input() there.
Move the call to cp2112_gpio_direction_input() earlier to have a working
driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
EHL is a new platform using ishtp solution, add its device id
to support list.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Distance values reported by 2nd-gen Intuos tablets are on an inverted
scale (0 == far, 63 == near). We need to change them over to a normal
scale before reporting to userspace or else userspace drivers and
applications can get confused.
Ref: https://github.com/linuxwacom/input-wacom/issues/98
Fixes: eda01dab53 ("HID: wacom: Add four new Intuos devices")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My recent to change to only use force_sig for a synchronous events
wound up breaking signal reception cifs and drbd. I had overlooked
the fact that by default kthreads start out with all signals set to
SIG_IGN. So a change I thought was safe turned out to have made it
impossible for those kernel thread to catch their signals.
Reverting the work on force_sig is a bad idea because what the code
was doing was very much a misuse of force_sig. As the way force_sig
ultimately allowed the signal to happen was to change the signal
handler to SIG_DFL. Which after the first signal will allow userspace
to send signals to these kernel threads. At least for
wake_ack_receiver in drbd that does not appear actively wrong.
So correct this problem by adding allow_kernel_signal that will allow
signals whose siginfo reports they were sent by the kernel through,
but will not allow userspace generated signals, and update cifs and
drbd to call allow_kernel_signal in an appropriate place so that their
thread can receive this signal.
Fixing things this way ensures that userspace won't be able to send
signals and cause problems, that it is clear which signals the
threads are expecting to receive, and it guarantees that nothing
else in the system will be affected.
This change was partly inspired by similar cifs and drbd patches that
added allow_signal.
Reported-by: ronnie sahlberg <ronniesahlberg@gmail.com>
Reported-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Cc: Steve French <smfrench@gmail.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Fixes: 247bc9470b ("cifs: fix rmmod regression in cifs.ko caused by force_sig changes")
Fixes: 72abe3bcf0 ("signal/cifs: Fix cifs_put_tcp_session to call send_sig instead of force_sig")
Fixes: fee109901f ("signal/drbd: Use send_sig not force_sig")
Fixes: 3cf5d076fb ("signal: Remove task parameter from force_sig")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Some newer machines do not advertise legacy timers. The kernel can handle
that situation if the TSC and the CPU frequency are enumerated by CPUID or
MSRs and the CPU supports TSC deadline timer. If the CPU does not support
TSC deadline timer the local APIC timer frequency has to be known as well.
Some Ryzens machines do not advertize legacy timers, but there is no
reliable way to determine the bus frequency which feeds the local APIC
timer when the machine allows overclocking of that frequency.
As there is no legacy timer the local APIC timer calibration crashes due to
a NULL pointer dereference when accessing the not installed global clock
event device.
Switch the calibration loop to a non interrupt based one, which polls
either TSC (if frequency is known) or jiffies. The latter requires a global
clockevent. As the machines which do not have a global clockevent installed
have a known TSC frequency this is a non issue. For older machines where
TSC frequency is not known, there is no known case where the legacy timers
do not exist as that would have been reported long ago.
Reported-by: Daniel Drake <drake@endlessm.com>
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Daniel Drake <drake@endlessm.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1908091443030.21433@nanos.tec.linutronix.de
Link: http://bugzilla.opensuse.org/show_bug.cgi?id=1142926#c12
lockdep reports the following deadlock scenario:
WARNING: possible circular locking dependency detected
kworker/1:1/48 is trying to acquire lock:
000000008d7a62b2 (text_mutex){+.+.}, at: kprobe_optimizer+0x163/0x290
but task is already holding lock:
00000000850b5e2d (module_mutex){+.+.}, at: kprobe_optimizer+0x31/0x290
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (module_mutex){+.+.}:
__mutex_lock+0xac/0x9f0
mutex_lock_nested+0x1b/0x20
set_all_modules_text_rw+0x22/0x90
ftrace_arch_code_modify_prepare+0x1c/0x20
ftrace_run_update_code+0xe/0x30
ftrace_startup_enable+0x2e/0x50
ftrace_startup+0xa7/0x100
register_ftrace_function+0x27/0x70
arm_kprobe+0xb3/0x130
enable_kprobe+0x83/0xa0
enable_trace_kprobe.part.0+0x2e/0x80
kprobe_register+0x6f/0xc0
perf_trace_event_init+0x16b/0x270
perf_kprobe_init+0xa7/0xe0
perf_kprobe_event_init+0x3e/0x70
perf_try_init_event+0x4a/0x140
perf_event_alloc+0x93a/0xde0
__do_sys_perf_event_open+0x19f/0xf30
__x64_sys_perf_event_open+0x20/0x30
do_syscall_64+0x65/0x1d0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #0 (text_mutex){+.+.}:
__lock_acquire+0xfcb/0x1b60
lock_acquire+0xca/0x1d0
__mutex_lock+0xac/0x9f0
mutex_lock_nested+0x1b/0x20
kprobe_optimizer+0x163/0x290
process_one_work+0x22b/0x560
worker_thread+0x50/0x3c0
kthread+0x112/0x150
ret_from_fork+0x3a/0x50
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(module_mutex);
lock(text_mutex);
lock(module_mutex);
lock(text_mutex);
*** DEADLOCK ***
As a reproducer I've been using bcc's funccount.py
(https://github.com/iovisor/bcc/blob/master/tools/funccount.py),
for example:
# ./funccount.py '*interrupt*'
That immediately triggers the lockdep splat.
Fix by acquiring text_mutex before module_mutex in kprobe_optimizer().
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: d5b844a2cf ("ftrace/x86: Remove possible deadlock between register_kprobe() and ftrace_run_update_code()")
Link: http://lkml.kernel.org/r/20190812184302.GA7010@xps-13
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If a task is PI-blocked (blocking on sleeping spinlock) then we don't want to
schedule a new kworker if we schedule out due to lock contention because !RT
does not do that as well. A spinning spinlock disables preemption and a worker
does not schedule out on lock contention (but spin).
On RT the RW-semaphore implementation uses an rtmutex so
tsk_is_pi_blocked() will return true if a task blocks on it. In this case we
will now start a new worker which may deadlock if one worker is waiting on
progress from another worker. Since a RW-semaphore starts a new worker on !RT,
we should do the same on RT.
XFS is able to trigger this deadlock.
Allow to schedule new worker if the current worker is PI-blocked.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20190816160626.12742-1-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While trawling through the dedupe file comparison code trying to fix
page deadlocking problems, Dave Chinner noticed that the reflink code
only takes shared IOLOCK/MMAPLOCKs on the source file. Because
page_mkwrite and directio writes do not take the EXCL versions of those
locks, this means that reflink can race with writer processes.
For pure remapping this can lead to undefined behavior and file
corruption; for dedupe this means that we cannot be sure that the
contents are identical when we decide to go ahead with the remapping.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Each iteration of for_each_child_of_node puts the previous
node, but in the case of a goto from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
goto in two places.
Issue found with Coccinelle.
Fixes: 119f517362 (drm/mediatek: Add DRM Driver for Mediatek SoC MT8173)
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
When a Tx timestamp is requested, a pointer to the skb is stored in the
ravb_tstamp_skb struct. This was done without an skb_get. There exists
the possibility that the skb could be freed by ravb_tx_free (when
ravb_tx_free is called from ravb_start_xmit) before the timestamp was
processed, leading to a use-after-free bug.
Use skb_get when filling a ravb_tstamp_skb struct, and add appropriate
frees/consumes when a ravb_tstamp_skb struct is freed.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Tho Vu <tho.vu.wh@rvc.renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
flow_offload hardware priority fixes
This patchset contains two updates for the flow_offload users:
1) Pass the major tc priority to drivers so they do not have to
lshift it. This is a preparation patch for the fix coming in
patch #2.
2) Set the hardware priority from the netfilter basechain priority,
some drivers break when using the existing hardware priority
number that is set to zero.
v5: fix patch 2/2 to address a clang warning and to simplify
the priority mapping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds initial support for offloading basechains using the
priority range from 1 to 65535. This is restricting the netfilter
priority range to 16-bit integer since this is what most drivers assume
so far from tc. It should be possible to extend this range of supported
priorities later on once drivers are updated to support for 32-bit
integer priorities.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc transparently maps the software priority number to hardware. Update
it to pass the major priority which is what most drivers expect. Update
drivers too so they do not need to lshift the priority field of the
flow_cls_common_offload object. The stmmac driver is an exception, since
this code assumes the tc software priority is fine, therefore, lshift it
just to be conservative.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In i2400m_barker_db_init(), 'options_orig' is allocated through kstrdup()
to hold the original command line options. Then, the options are parsed.
However, if an error occurs during the parsing process, 'options_orig' is
not deallocated, leading to a memory leak bug. To fix this issue, free
'options_orig' before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver name gets exposed in sysfs under /sys/bus/pci/drivers
so it should look like other devices. Change it to be common
format (instead of "Cavium PTP").
This is a trivial fix that was observed by accident because
Debian kernels were building this driver into kernel (bug).
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to wait until a completion is received to unmap
TX descriptor buffers that have been passed to the hypervisor.
Instead unmap it when the hypervisor call has completed. This patch
avoids the possibility that a buffer will not be unmapped because
a TX completion is lost or mishandled.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Devesh K. Singh <devesh_singh@in.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Bug fixes.
2 Bug fixes related to 57500 shutdown sequence and doorbell sequence,
2 TC Flower bug fixes related to the setting of the flow direction,
1 NVRAM update bug fix, and a minor fix to suppress an unnecessary
error message. Please queue for -stable as well. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
FW expects the driver to provide unique flow reference handles
for Tx or Rx flows. When a Tx flow and an Rx flow end up sharing
a reference handle, flow offload does not seem to work.
This could happen in the case of 2 flows having their L2 fields
wildcarded but in different direction.
Fix to incorporate the flow direction as part of the L2 key
v2: Move the dir field to the end of the bnxt_tc_l2_key struct to
fix the warning reported by kbuild test robot <lkp@intel.com>.
There is existing code that initializes the structure using
nested initializer and will warn with the new u8 field added to
the beginning. The structure also packs nicer when this new u8 is
added to the end of the structure [MChan].
Fixes: abd43a1352 ("bnxt_en: Support for 64-bit flow handle.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Direction of the flow is determined using src_fid. For an RX flow,
src_fid is PF's fid and for TX flow, src_fid is VF's fid. Direction
of the flow must be specified, when getting statistics for that flow.
Currently, for DECAP flow, direction is determined incorrectly, i.e.,
direction is initialized as TX for DECAP flow, instead of RX. Because
of which, stats are not reported for this DECAP flow, though it is
offloaded and there is traffic for that flow, resulting in flow age out.
This patch fixes the problem by determining the DECAP flow's direction
using correct fid. Set the flow direction in all cases for consistency
even if 64-bit flow handle is not used.
Fixes: abd43a1352 ("bnxt_en: Support for 64-bit flow handle.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For newly added NVM parameters, older firmware may not have the support.
Suppress the error message to avoid the unncessary error message which is
triggered when devlink calls the driver during initialization.
Fixes: 782a624d00 ("bnxt_en: Add bnxt_en initial params table and register it.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If FW returns FRAG_ERR in response error code, driver is resending the
command only when HWRM command returns success. Fix the code to resend
NVM_INSTALL_UPDATE command with DEFRAG install flags, if FW returns
FRAG_ERR in its response error code.
Fixes: cb4d1d6261 ("bnxt_en: Retry failed NVM_INSTALL_UPDATE with defragmentation flag enabled.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both RX buffers and RX aggregation buffers have to be
replenished at the end of NAPI, post the RX aggregation buffers first
before RX buffers. Otherwise, we may run into a situation where
there are only RX buffers without RX aggregation buffers for a split
second. This will cause the hardware to abort the RX packet and
report buffer errors, which will cause unnecessary cleanup by the
driver.
Ringing the Aggregation ring doorbell first before the RX ring doorbell
will prevent some of these buffer errors. Use the same sequence during
ring initialization as well.
Fixes: 697197e5a1 ("bnxt_en: Re-structure doorbells.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device shutdown, the VNIC clearing sequence needs to be modified
to free the VNIC first before freeing the RSS contexts. The current
code is doing the reverse and we can get mis-directed RX completions
to CP ring ID 0 when the RSS contexts are freed and zeroed. The clearing
of RSS contexts is not required with the new sequence.
Refactor the VNIC clearing logic into a new function bnxt_clear_vnic()
and do the chip specific VNIC clearing sequence.
Fixes: 7b3af4f75b ("bnxt_en: Add RSS support for 57500 chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kalmia_init_and_get_ethernet_addr(), 'usb_buf' is allocated through
kmalloc(). In the following execution, if the 'status' returned by
kalmia_send_init_packet() is not 0, 'usb_buf' is not deallocated, leading
to memory leaks. To fix this issue, add the 'out' label to free 'usb_buf'.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cx82310_bind(), 'dev->partial_data' is allocated through kmalloc().
Then, the execution waits for the firmware to become ready. If the firmware
is not ready in time, the execution is terminated. However, the allocated
'dev->partial_data' is not deallocated on this path, leading to a memory
leak bug. To fix this issue, free 'dev->partial_data' before returning the
error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
- spi-nor: Fix to correctly set the WP pin
-----BEGIN PGP SIGNATURE-----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=AzKU
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fix from Richard Weinberger:
"A single fix for MTD to correctly set the spi-nor WP pin"
* tag 'fixes-for-5.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: Fix the disabling of write protection at init
