It is a low-level I/O access function, so io.c is the natural place for
it.
While we're moving the code, reduce the scope of some variables, use
compound assignment operators, and add/adjust some comments.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093717.3198716-4-oswald.buddenhagen@gmx.de>
There is only one call site, and there we already know that we actually
have a firmware.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093717.3198716-3-oswald.buddenhagen@gmx.de>
Firstly, it is pointless to explicitly disable the power to the dock
prior to resetting the FPGA, as the latter will do the former anyway.
Secondly, it doesn't make much sense to check whether the FPGA is
already programmed. It's much simpler to just presume it is, and issue
the self-reset command. If it isn't, the effect isn't worse than the
checks themselves. As a side effect, we lose the info if the reset
fails, but there is no plausible way how that could happen unless the
card burns out while operating, and in that case we'll detect a firmware
upload failure a bit later anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093717.3198716-2-oswald.buddenhagen@gmx.de>
We did not delay after the second strobe signal, so another immediately
following access could potentially corrupt the written value.
This is a purely speculative fix with no supporting evidence, but after
taking out the spinlocks around the writes, it seems plausible that a
modern processor could be actually too fast. Also, it's just cleaner to
be consistent.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-7-oswald.buddenhagen@gmx.de>
A side effect of making the dock monitoring interrupt-driven was that
we'd be very quick to program a freshly connected dock. However, for
unclear reasons, the dock does not work when we do that - despite the
FPGA netlist upload going just fine. We work around this by adding a
delay before programming the dock; for safety, the value is several
times as much as was determined empirically.
Note that a badly timed dock hot-plug would have triggered the problem
even before the referenced commit - but now it would happen 100% instead
of about 3% of the time, thus making it impossible to work around by
re-plugging.
Fixes: fbb64eedf5 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-6-oswald.buddenhagen@gmx.de>
The FPGA access through the GPIO port does not interfere with other
sound processor register access, so there is no need to subject it to
emu_lock. And after moving all FPGA access out of the interrupt handler,
it does not need to be IRQ-safe, either.
What's more, attaching the dock causes a firmware upload, which takes
several seconds. We really don't want to disable IRQs for this long, and
even less also have someone else spin with IRQs disabled waiting for us.
Therefore, use a mutex for FPGA access locking.
This makes the code somewhat more noisy, as we need to wrap bigger
sections into the mutex, as it needs to enclose the spinlocks.
The latter has the "side effect" of fixing dock FPGA programming in a
corner case: a really badly timed mixer access right between entering
FPGA programming mode and uploading the netlist would mess up the
protocol.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-5-oswald.buddenhagen@gmx.de>
The actual event processing was already done by workqueue items. We can
move the event dispatching there as well, rather than doing it already
in the interrupt handler callback.
This change has a rather profound "side effect" on the reliability of
the FPGA programming: once we enter programming mode, we must not issue
any snd_emu1010_fpga_{read,write}() calls until we're done, as these
would badly mess up the programming protocol. But exactly that would
happen when trying to program the dock, as that triggers GPIO interrupts
as a side effect. This is mitigated by deferring the actual interrupt
handling, as workqueue items are not re-entrant.
To avoid scheduling the dispatcher on non-events, we now explicitly
ignore GPIO IRQs triggered by "uninteresting" pins, which happens a lot
as a side effect of calling snd_emu1010_fpga_{read,write}().
Fixes: fbb64eedf5 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-4-oswald.buddenhagen@gmx.de>
Pulled out of the next patch to improve its legibility.
As the function is now available, call it directly from
snd_emu10k1_emu1010_init(), thus making the MicroDock firmware loading
synchronous - there isn't really a reason not to. Note that this does
not affect the AudioDocks of rev1 cards, as these have no independent
power supplies, and thus come up only a while after the main card is
initialized.
As a drive-by, adjust the priorities of two messages to better reflect
their impact.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-3-oswald.buddenhagen@gmx.de>
While there are two separate IRQ status bits for dock attach and detach,
the hardware appears to mix them up more or less randomly, making them
useless for tracking what actually happened. It is much safer to check
the dock status separately and proceed based on that, as the old polling
code did.
Note that the code assumes that only the dock can be hot-plugged - if
other option card bits changed, the logic would break.
Fixes: fbb64eedf5 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-2-oswald.buddenhagen@gmx.de>
Add laptop using CS35L41 HDA.
This laptop does not have _DSD, so require entries in property
configuration table for cs35l41_hda driver.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Message-ID: <20240423162303.638211-3-sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This laptop does not have the correct _DSD settings, so needs to
obtain its configuration from the configuration table.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Message-ID: <20240423162303.638211-2-sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Haier Boyue G42 with ALC269VC cannot detect the MIC of headset,
the line out and internal speaker until
ALC269VC_FIXUP_ACER_VCOPPERBOX_PINS quirk applied.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Cc: <stable@vger.kernel.org>
Message-ID: <20240419082159.476879-1-aichao@kylinos.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headset mic requires a fixup to be properly detected/used.
As a reference, this specific model from 2021 reports
the following devices:
https://alsa-project.org/db/?f=1a5ddeb0b151db8fe051407f5bb1c075b7dd3e4a
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <stable@vger.kernel.org>
Message-ID: <b92a9e49fb504eec8416bcc6882a52de89450102.1713370457.git.mchehab@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the correct pin table for Asus GU605M and GA403U, enabling all
speakers to be controlled with the master.
Updated quirks for GU605M and GA403U by including the pin table patch
in the chain.
Co-developed-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Vitalii Torshyn <vitaly.torshyn@gmail.com>
Message-ID: <20240411125803.18539-1-vitaly.torshyn@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These laptops do not have _DSD and must be added by configuration
table, however, the initial entries for them are incorrect:
Neither laptop contains a Speaker ID GPIO.
This issue would not affect audio playback, but may affect which files
are loaded when loading firmware.
Fixes: b67a7dc418 ("ALSA: hda/realtek: Add sound quirks for Lenovo Legion slim 7 16ARHA7 models")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240411110813.330483-8-sbinding@opensource.cirrus.com>
In every case the 'dir' argument to cs35l41_request_firmware_file() is passed
the string "cirrus/", so this is a redundant argument and can be removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240411110813.330483-7-sbinding@opensource.cirrus.com>
The original mechanism for applying calibration assumed that the
calibration data would be ordered the same as the amp instances.
However, for some 4 amp laptops, this is not the case.
To ensure that the correct calibration is applied to the correct amp,
the calibration data contains a unique id, which matches a unique id
inside the CS35L41. This can be used to match to the correct data
entry. This mechanism is available inside the shared module cs-amp-lib.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240411110813.330483-6-sbinding@opensource.cirrus.com>
Currently, all PC systems are set to use VBSTMON for DSP1RX5_SRC,
however, this is required only for external boost systems.
Internal boost systems require VPMON instead of VBSTMON to be the
input to DSP1RX5_SRC.
All systems require DSP1RX6_SRC to be set to VBSTMON.
Also fix incorrect comment for DACPCM1_SRC to use DSP1TX1.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240411110813.330483-5-sbinding@opensource.cirrus.com>
Add 4 laptops using CS35L41 HDA.
None of these laptops have _DSD, so require entries in property
configuration table for cs35l41_hda driver.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240411110813.330483-4-sbinding@opensource.cirrus.com>
Add support for 2 new HP Omen models without _DSD into configuration
table.
These laptops use the PCM Gain setting for the tuning setting file.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240411110813.330483-3-sbinding@opensource.cirrus.com>
Some systems requires different max PCM Gains settings than the default.
The current default value, when running firmware is 17.5 dB, which is
used for all systems. Some systems require lower values.
Value when running without firmware is 4.5 dB and remains unchanged.
Since the gain value is dependent on Tuning and Firmware, it can
change, so it cannot be saved in _DSD. Instead we can store it inside
a configuration binary file alongside the Firmware and Tuning files.
The gain value increments in steps of 1 dB, with value 0 representing
0.5 dB. The max value is 20, which corresponds to 20.5 dB.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240411110813.330483-2-sbinding@opensource.cirrus.com>
Add new vendor_id and subsystem_id to support new Lenovo laptop
ThinkPad ICE-1
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240411091823.1644-1-shenghao-ding@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is recommended that on Lunar Lake the PIO (immediate command response)
is used instead of CORB/RIRB for commands/verbs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240409083812.14001-5-peter.ujfalusi@linux.intel.com>
Set the use_pio_for_commands flag in case AZX_DCAPS_PIO_COMMANDS quirk is
enabled.
When the PIO command mode is used we can re-use the existing
azx_single_send_cmd() / azx_single_get_response() functions safely as the
CORB DMA is not going to be enabled in snd_hdac_bus_init_cmd_io().
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240409083812.14001-4-peter.ujfalusi@linux.intel.com>
Add AZX_DCAPS_PIO_COMMANDS quirk (bit 31) and use_pio_for_commands flag to
be able to select PIO mode as alternative for CORB based command sending
while retaining the RIRB functionality to receive unsolicited responses.
This mode differs from the azx single_cmd mode when RIRB is disabled.
The mixed mode is needed on Lunar Lake family because it is recommended to
use Immediate Command Response (PIO mode) instead of CORB for HDA commands.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240409083812.14001-2-peter.ujfalusi@linux.intel.com>
Adds calls to disable regmap cache-only after a successful return from
cs35l56_wait_for_firmware_boot().
This is to prepare for a change in the shared ASoC module that will
leave regmap in cache-only mode after cs35l56_system_reset(). This is
to prevent register accesses going to the hardware while it is
rebooting.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://msgid.link/r/20240408101803.43183-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need for it to be 32 samples - 3 will do just fine (which is
the interpolator's epsilon). The old size was presumably meant to
compensate for the cache's presence, but we're now handling that
properly.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240406064830.1029573-17-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Compensate for the cache lag of 64 frames, and actually populate the
cache. Without these, the playback would start with garbage (which
would be (mostly?) masqueraded by the note's attack phase).
Note that we set the starting address only 61 frames ahead, to
compensate for the interpolator's epsilon. Unlike for PCM playback, we
don't even need to manually silence-fill the first frames in the cache,
because we insert some silence in front of each sample anyway.
A challenge are extremely short samples with a loop end below the cache
size, because a) we'd have to wrap the current address to be within the
loop and b) automatic pre-filling of the cache with the right data does
not work in this case.
We could pre-fill the cache manually, but that's slow, requires
additional code for each sample width, and is made even more complex by
the driver's virtual address space having no contiguous mapping for the
CPU.
We could have the engine fill the cache piece-wise (which is really what
happens when playback is running), but that would also be complex, and
we'd need to wait for the engine to handle each piece, so it wouldn't be
that much faster than the manual fill.
For the case of requiring only one loop iteration prior to reaching the
cache size, we could leverage the engine's looping mechanism around
CCR_CACHELOOPFLAG, but this special case doesn't seem worth the
complexity.
So we just unroll the loop as far as necessary to be able to play back
the sample without any fiddling.
Pedantically, this would be incorrect for loop-until-release samples
with a low loop end which are released very quickly, but that would be
relatively harmless, is not a plausible use case in the first place, and
SoundFont sample mode 3 isn't actually implemented anyway (it's
conflated with mode 1, infinite looping).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240406064830.1029573-16-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The offsets are counted in samples, not in bytes.
While the code block is being rewritten, also move it up a bit, to avoid
churn in a subsequent patch.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240406064830.1029573-13-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This de-duplicates the code slightly. But the real reason is that it
moves the code up, which the next patch will depend on.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240406064830.1029573-12-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Samples are byte-sized in this mode, and thus the offset calculation
needs no shifting.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240406064830.1029573-11-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hardware supports S16LE and U8 samples, while U16LE and S8 (which
the driver implicitly claims to support) require sign flipping.
Note that this matters only for the GUS patch loader, as the implemented
SoundFont v2.01 spec is limited to S16LE.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240406064830.1029573-10-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert some checks in snd_emu10k1_sample_new() back into assertions (as
they were prior to da3cec35dd (ALSA: Kill snd_assert() in sound/pci/*,
2008-08-08)), and move them into the low-level memory access functions
they protect.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240406064830.1029573-9-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This does several closely related things:
- Move the code from the drivers into the SoundFont loader, which
de-duplicates it.
- Sort of explain the weird "recalculate address offset" feature. Note
that I don't think it actually makes any sense - the calling user
space code should do that. The background is certainly that the source
data (the SoundFont format) uses pointers into a single wave block
(and the API allows doing the same for on-board ROM), but the API
expects the wave data from user space to be pre-chopped into
individual patches anyway.
- Make sure that the specified offsets actually lie within the supplied
wave data. Note that we don't validate ROM offsets, so one can play
back anything within the sound card's address space.
- In load_guspatch(), don't call the sample_new callback anymore when
the patch size is zero, as was already the case in load_data(). The
callbacks would instantly return in that case anyway; these checks are
now removed.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240406064830.1029573-7-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is required only to implement WAVE_BIDIR_LOOP and WAVE_LOOP_BACK in
the GUS patch loader. It has not worked on emu10k1 since before ALSA hit
mainline, yet nobody appears to have complained. And as it isn't super
easy to implement, just admit defeat and clean up the code.
If somebody wanted to resurrect the feature, the emu8k driver could
serve as a template, but the code would be quite different. But
arguably, this should be done in user space in the first place, as this
doesn't represent a hardware feature (somewhat ironically, the actual
GUS driver has no synth support, and therefore no GUS patch loader).
Note that instead of properly rejecting affected samples, we continue to
just pretend that the feature wasn't requested. This is extremely
questionable behavior, but avoids that possibly unused instruments
suddenly prevent loading the entire file, which would break backwards
compatibility. But at least we log a warning now.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240406064830.1029573-6-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Calibrated data was written into an incorrect register, which cause
speaker protection sometimes malfuctions
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240406132010.341-1-shenghao-ding@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for HP SnowWhite laptops with CS35L51 amplifiers on I2C
bus connected to Realtek codec.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Message-ID: <20240405210635.22193-1-vitalyr@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
Set of changes targeting the avs-driver only. No new features, patchset
either fixes or fortifies existing code.
Patchset starts off with a fix for debugbility on ICL+ platforms which I
have forgotten to fixup when providing support for these initially.
The next two address copier module initialization, most importantly,
silence the gcc 'field-spanning write' false-positive.
The following four:
6/13 ASoC: Intel: avs: Replace risky functions with safer variants
7/13 ASoC: Intel: avs: Fix potential integer overflow
8/13 ASoC: Intel: avs: Test result of avs_get_module_entry()
9/13 ASoC: Intel: avs: Remove dead code
address problems found out by Coverity static analysis tool.
The last two worth mentioning are: recommendation from the firmware team
to wake subsystem from D0ix when starting any pipeline -and- shielding
against invalid period/buffer sizes. Audio format shall be taken into
consideration when calculating either of these.
Amadeusz Sławiński (2):
ASoC: Intel: avs: Restore stream decoupling on prepare
ASoC: Intel: avs: Add assert_static to guarantee ABI sizes
Cezary Rojewski (11):
ASoC: Intel: avs: Fix debug-slot offset calculation
ASoC: Intel: avs: Silence false-positive memcpy() warnings
ASoC: Intel: avs: Fix config_length for config-less copiers
ASoC: Intel: avs: Fix ASRC module initialization
ASoC: Intel: avs: Replace risky functions with safer variants
ASoC: Intel: avs: Fix potential integer overflow
ASoC: Intel: avs: Test result of avs_get_module_entry()
ASoC: Intel: avs: Remove dead code
ASoC: Intel: avs: Wake from D0ix when starting streaming
ASoC: Intel: avs: Init debugfs before booting firmware
ASoC: Intel: avs: Rule invalid buffer and period sizes out
sound/soc/intel/avs/avs.h | 1 +
sound/soc/intel/avs/cldma.c | 2 +-
sound/soc/intel/avs/core.c | 4 +--
sound/soc/intel/avs/icl.c | 12 ++++++---
sound/soc/intel/avs/loader.c | 6 +++--
sound/soc/intel/avs/messages.h | 47 ++++++++++++++++++++++++++++++++--
sound/soc/intel/avs/path.c | 13 ++++------
sound/soc/intel/avs/pcm.c | 34 +++++++++++++++++++++++-
sound/soc/intel/avs/probes.c | 14 ++++++----
9 files changed, 109 insertions(+), 24 deletions(-)
--
2.25.1
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
This set of patches factors out some repeated code to clean up
firmware control read/write functions, and removes some redundant
control notification code.
base-commit: f193957b0f
Any control that the driver is updating should be marked as SYSTEM and
therefore will not have an ALSA control to notify.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://msgid.link/r/20240325113127.112783-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the cs_dsp_coeff_lock_and_[read|write]_ctrl() wrappers tidies
the calling functions as it does not need to manage the DSP pwr_lock.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://msgid.link/r/20240325113127.112783-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the realtek quirk to initialise the Cirrus amp correctly and adds
related quirk for missing DSD properties. This model laptop has slightly
updated internals compared to the previous version with Realtek Codec
ID of 0x1caf.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Message-ID: <20240402015126.21115-1-luke@ljones.dev>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch addresses an issue with the Panasonic CF-SZ6's existing quirk,
specifically its headset microphone functionality. Previously, the quirk
used ALC269_FIXUP_HEADSET_MODE, which does not support the CF-SZ6's design
of a single 3.5mm jack for both mic and audio output effectively. The
device uses pin 0x19 for the headset mic without jack detection.
Following verification on the CF-SZ6 and discussions with the original
patch author, i determined that the update to
ALC269_FIXUP_ASPIRE_HEADSET_MIC is the appropriate solution. This change
is custom-designed for the CF-SZ6's unique hardware setup, which includes
a single 3.5mm jack for both mic and audio output, connecting the headset
microphone to pin 0x19 without the use of jack detection.
Fixes: 0fca97a29b ("ALSA: hda/realtek - Add Panasonic CF-SZ6 headset jack quirk")
Signed-off-by: I Gede Agastya Darma Laksana <gedeagas22@gmail.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240401174602.14133-1-gedeagas22@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes the sound not working from internal speakers on
Lenovo Legion Slim 7 16ARHA7 models. The correct subsystem ID
have been added to cs35l41_hda_property.c and patch_realtek.c.
Signed-off-by: Christian Bendiksen <christian@bendiksen.me>
Cc: <stable@vger.kernel.org>
Message-ID: <20240401122603.6634-1-christian@bendiksen.me>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As already anticipated in the original commit, playback was broken for
very short samples. I just didn't expect it to be an actual problem,
because we're talking about less than 1.5 milliseconds here. But clearly
such wavetable samples do actually exist.
The problem was that for such short samples we'd set the current
position beyond the end of the loop, so we'd run off the end of the
sample and play garbage.
This is a bigger (more audible) problem than the original one, which was
that we'd start playback with garbage (whatever was still in the cache),
which would be mostly masked by the note's attack phase.
So revert to the old behavior for now. We'll subsequently fix it
properly with a bigger patch series.
Note that this isn't a full revert - the dead code is not re-introduced,
because that would be silly.
Fixes: df335e9a8b ("ALSA: emu10k1: fix synthesizer sample playback position and caching")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218625
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240401145805.528794-1-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These ASUS laptops use the Realtek HDA codec combined with a number of
CS35L56 amplifiers.
The SSID of the GA403U matches a previous ASUS laptop - we can tell them
apart because they use different codecs.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Message-ID: <20240329112803.23897-1-simont@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding the ACPI HIDs to the match table triggers the cs35l56-hda modules
to be loaded on boot so that Serial Multi Instantiate can add the
devices to the bus and begin the driver init sequence.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Message-ID: <20240328121355.18972-1-simont@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the existing fixup to certain TF platforms implementing
the ALC274 codec with a headset jack. It fixes/activates the inactive
microphone of the headset.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240328102757.50310-1-wse@tuxedocomputers.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The debug message "Playback action not supported: action" is not useful,
because the action was previously printed, and the list of supported
actions are intentional.
Remove the debug statement from the default switch case.
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Message-ID: <8b9546db6c92dea4476a7247a88d56248c2ba8c2.1711469583.git.soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes it is useful to examine the timing of kcontrol events.
Add debug statements to each kcontrol.
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Message-ID: <18ff4b0caab90a2dacf907e62346fd5079a9eb1a.1711469583.git.soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "Speaker Digital Gain" kcontrol controls the TAS2781_DVC_LVL (0x1A)
register. Unfortunately the tas2563 does not have DVC_LVL, but has
INT_MASK0 in 0x1A, which has been misused so far.
Since commit c1947ce61f ("ALSA: hda/realtek: tas2781: enable subwoofer
volume control") the volume of the tas2781 amplifiers can be controlled
by the master volume, so this digital gain kcontrol is not needed.
Remove it.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Message-ID: <741fc21db994efd58f83e7aef38931204961e5b2.1711469583.git.soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialization is completed before adding the component as that can
start the process of the device binding and trigger actions that check
init_done.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Message-ID: <20240325145510.328378-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The system and amplifier names influence which firmware and tuning files
are downloaded to the device; log these values to aid end-user system
support.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-ID: <20240325142937.257869-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cirrus amps support for this laptop was added in patch:
33e5e648e6 ("ALSA: hda: cs35l41: Support additional HP Envy Models")
This patch adds fixes for wrong pincfgs, wrong DAC selection and
mute/micmute LEDs.
Signed-off-by: Anthony I Gilea <i@cpp.in>
Message-ID: <e2a7aaed-e9d7-4d36-8abf-b71dfd32a0ff@cpp.in>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we tested the headphone playback on 2 LG machines, if we set
the volume to the max value or near to the max value, the sound is too
loud, it could even bring harm to listeners.
A workaround is to decrease the max volume to a reasonable value for
the headphone's amplifier, then the users couldn't set the volume
bigger than that value from the userspace.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Message-ID: <20240318011128.156023-1-hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keyboard has an LED that is ON/OFF when mic is muted/active
- LED is controlled by GPIO pin
- Patch enables led to appear in /sys/class/leds/ as hda::micmute
- Enables LED when mic is MUTED
- Disables LED when mic is active
[ fixed white spaces by tiwai ]
Signed-off-by: Ian Murphy <iano200@gmail.com>
Message-ID: <20240316094157.13890-1-iano200@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The speakers on the Lenovo Yoga 9 14IMH9 are similar to previous generations
such as the 14IAP7, and the bass speakers can be fixed using similar methods
with one caveat: 14IMH9 uses CS35L41 amplifiers which need to be activated
separately.
Signed-off-by: Jichi Zhang <i@jichi.ca>
Message-ID: <20240315081954.45470-3-i@jichi.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The runtime_pm handling seems to have been loosely inspired by the
cs32l41 driver, but in this case the get_noresume/put sequence is not
required.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-ID: <20240312161217.79510-1-pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some HP laptops have received revisions that altered their board IDs
and therefore the current patches/quirks do not apply to them.
Specifically, for my Probook 440 G8, I have a board ID of 8a74.
It is necessary to add a line for that specific model.
Signed-off-by: Valentine Altair <faetalize@proton.me>
Cc: <stable@vger.kernel.org>
Message-ID: <kOqXRBcxkKt6m5kciSDCkGqMORZi_HB3ZVPTX5sD3W1pKxt83Pf-WiQ1V1pgKKI8pYr4oGvsujt3vk2zsCE-DDtnUADFG6NGBlS5N3U4xgA=@proton.me>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This has been quite a small release, there's a lot of driver specific
cleanups and minor enhancements but hardly anything on the core and only
one new driver. Highlights include:
- SoundWire support for AMD ACP 6.3 systems.
- Support for reporting version information for AVS firmware.
- Support DSPless mode for Intel Soundwire systems.
- Support for configuring CS35L56 amplifiers using EFI calibration
data.
- Log which component is being operated on as part of power management
trace events.
- Support for Microchip SAM9x7, NXP i.MX95 and Qualcomm WCD939x
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmXvE1AACgkQJNaLcl1U
h9B15Qf8CrS5zHsD54bvTcumkDgbJ8Dl9f5qz4UN/AX0mcZ1UJU6sQ0HxIGEtlPc
26pneHV9ZA0wSPw432NBpwcfe7AsWASmKUf6S2hsj4LMvnoj75iiZum8TE71ior7
QI9ARnNipB1tHk7Kmgs/pe+CqX3hhCVqYUI9w5fMIj05T5qwYbqCERws6JA2Uw97
6fb5CgI2uRYTShVVmYsE/FlxXmZqNN4NnNxlVvUSM5TE3Tayf+BCEqhpwuh59Pt/
G+mZfj3eof0HdjGPQbLRPOWQOa3bT8gmT89OlbmmMf17+975pgShBbARzkv41vk1
ifr6muHweaDLD7gloS/HUr4JRo9Daw==
=ZYC5
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v6.9
This has been quite a small release, there's a lot of driver specific
cleanups and minor enhancements but hardly anything on the core and only
one new driver. Highlights include:
- SoundWire support for AMD ACP 6.3 systems.
- Support for reporting version information for AVS firmware.
- Support DSPless mode for Intel Soundwire systems.
- Support for configuring CS35L56 amplifiers using EFI calibration
data.
- Log which component is being operated on as part of power management
trace events.
- Support for Microchip SAM9x7, NXP i.MX95 and Qualcomm WCD939x
After system_resume the amplifers will remain off, even if they were on
before system_suspend.
Use playback_started bool to save the playback state, and restore power
state based on it.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <1742b61901781826f6e6212ffe1d21af542d134a.1709918447.git.soyer@irl.hu>
The runtime_resume function calls prmg_load and apply_calibration
functions, but system_resume also calls them, so calling
pm_runtime_force_resume before reset is unnecessary.
For consistency, do not call the pm_runtime_force_suspend in
system_suspend, as runtime_suspend does the same.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <d0b4cc1248b9d375d59c009563da42d60d69eac3.1709918447.git.soyer@irl.hu>
The amplifier doesn't loose register state in software shutdown mode, so
there is no need to reset the cur_* values.
Without these resets, the amplifier can be turned on after
runtime_suspend without waiting for the program and
profile to be restored.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <aa27ae084150988bf6a0ead7e3403bc485d790f8.1709918447.git.soyer@irl.hu>
The system_resume function uses dev_info for tracing, but the other pm
functions use dev_dbg.
Use dev_dbg as the other pm functions.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <140f3c689c9eb5874e6eb48a570fcd8207f06a41.1709918447.git.soyer@irl.hu>
Realtek codec on HP Envy laptop series are heavily modified by vendor.
Therefore, need intervention to make it work properly. The patch fixes:
- B&O soundbar speakers (between lid and keyboard) activation
- Enable LED on mute button
- Add missing process coefficient which affects the output amplifier
- Volume control synchronization between B&O soundbar and side speakers
- Unmute headset output on several HP Envy models
- Auto-enable headset mic when plugged
This patch was tested on HP Envy x360 13-AR0107AU with Realtek ALC285
The only unsolved problem is output amplifier of all built-in speakers
is too weak, which causes volume of built-in speakers cannot be loud
as vendor's proprietary driver due to missing _DSD parameter in the
firmware. The solution is currently on research. Expected to has another
patch in the future.
Potential fix to related issues, need test before close those issues:
- https://bugzilla.kernel.org/show_bug.cgi?id=189331
- https://bugzilla.kernel.org/show_bug.cgi?id=216632
- https://bugzilla.kernel.org/show_bug.cgi?id=216311
- https://bugzilla.kernel.org/show_bug.cgi?id=213507
Signed-off-by: Athaariq Ardhiansyah <foss@athaariq.my.id>
Message-ID: <20240310140249.3695-1-foss@athaariq.my.id>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the HID for the CS35L54 and CS35L57 Boosted Smart Amplifiers. These
have the same control interface as the CS35L56 so are handled by the
cs35l56-hda driver.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240308135900.603192-3-rf@opensource.cirrus.com>
hda_component.h uses hda_codec_dev from sound/hda_codec.h.
Include sound/hda_codec.h instead of assuming that it has already
been included by the parent .c file.
This isn't causing any problems with current code, so no need to
backport to older kernels.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-ID: <20240307111216.45053-2-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the conventional include guards around the content of the
hda_component.h header file. This prevents double-declaration of
struct hda_component if the header gets included multiple times.
This isn't causing any problems with current code, so no need to
backport to older kernels.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-ID: <20240307111216.45053-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP EliteBook using ALC236 codec which using 0x02 to
control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240304134033.773348-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There was one overlooked place to be replaced with
snd_ctl_find_id_mixer() for code simplification.
No functional change, only code refactoring.
Link: https://lore.kernel.org/r/20240304082158.8583-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Whilst this laptop contains _DSD inside the BIOS, there is an error in
this configuration. Override the _DSD in the BIOS with the correct
configuration for this laptop.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240301160154.158398-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In azx_probe_codecs function, when bus->codec_mask is becomes to 0(no codecs),
execute azx_init_chip, bus->codec_mask will be initialized to a value again,
this causes snd_hda_codec_new function to run, the process is as follows:
-->snd_hda_codec_new
-->snd_hda_codec_device_init
-->snd_hdac_device_init---snd_hdac_read_parm(...AC_PAR_VENDOR_ID) 2s
---snd_hdac_read_parm(...AC_PAR_VENDOR_ID) 2s
---snd_hdac_read_parm(...AC_PAR_SUBSYSTEM_ID) 2s
---snd_hdac_read_parm(...AC_PAR_REV_ID) 2s
---snd_hdac_read_parm(...AC_PAR_NODE_COUNT) 2s
when no codecs, read communication is error, each command will be polled for
2 second, a total of 10s, it is easy to some problem.
like this:
2 [ 14.833404][ 6] [ T164] hda 0006:00: Codec #0 probe error; disabling it...
3 [ 14.844178][ 6] [ T164] hda 0006:00: codec_mask = 0x1
4 [ 14.880532][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0000
5 [ 15.891988][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0000
6 [ 16.978090][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0001
7 [ 18.140895][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0002
8 [ 19.135516][ 6] [ T164] hda 0006:00: too slow response, last cmd=0x0f0004
10 [ 19.900086][ 6] [ T164] hda 0006:00: no codecs initialized
11 [ 45.573398][ 2] [ C2] watchdog: BUG: soft lockup - CPU#2 stuck for 22s! [kworker/2:0:25]
Here, when bus->codec_mask is 0, use a direct break to avoid execute snd_hda_codec_new function.
Signed-off-by: songxiebing <songxiebing@kylinos.cn>
Link: https://lore.kernel.org/r/20240301011841.7247-1-soxiebing@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Headset Mic will no show at resume back.
This patch will fix this issue.
Fixes: d7f32791a9 ("ALSA: hda/realtek - Add headset Mic support for Lenovo ALC897 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/4713d48a372e47f98bba0c6120fd8254@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It had pop noise from Headphone port when system reboot state.
If NID 58h Index 0x0 to fill default value, it will reduce pop noise.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/7493e207919a4fb3a0599324fd010e3e@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
Factory calibration of the speakers stores the calibration information
into an EFI variable.
This set of patches adds support for applying speaker calibration
data from that EFI variable.
The HDA patch (#5) depends on the ASoC patches #2 and #3
If there are factory calibration settings in EFI, extract the
settings and write them to the firmware calibration controls.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240223153910.2063698-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable clock is being assigned a value that is never read,
it is being re-assigned a new value in every case in the following
switch statement. The assignment is redundant and can be removed.
Cleans up clang scan build warning:
sound/pci/echoaudio/echoaudio_3g.c:277:2: warning: Value stored
to 'clock' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240221113809.3410109-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP mt440 Thin Client uses an ALC236 codec and needs the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make the mute and
micmute LEDs work.
There are two variants of the USB-C PD chip on this device. Each uses
a different BIOS and board ID, hence the two entries.
Signed-off-by: Eniac Zhang <eniac-xw.zhang@hp.com>
Signed-off-by: Alexandru Gagniuc <alexandru.gagniuc@hp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240220175812.782687-1-alexandru.gagniuc@hp.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far the setup of BDL table is performed at the prepare stage, where
all PCM parameters have been already set up. When something wrong
happens at it, we return -EINVAL; it's supposed to be a rare case
since the involved memory allocation is a small chunk of kmalloc for
the table.
However, when we receive too many small non-contiguous pages in highly
fragmented memories, it may overflow the max table size, resulting in
the same -EINVAL error from the prepare, too. A bad scenario is that
user-space cannot know what went wrong (as it's an error from the
prepare stage) and -EINVAL, hence it may retry with the same
parameters, failing again repeatedly.
In this patch, we try to set up the BDL table at hw_params right after
the buffer allocation, and return -ENOMEM if it overflows.
This allows user-space knowing that it should reduce the buffer size
request accordingly and may retry with more fitting parameters.
Link: https://lore.kernel.org/r/20240221100607.6565-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
The avs-driver continues to be utilized on more recent Intel machines.
As TGL-based (cAVS 2.5) e.g.: RPL, inherit most of the functionality
from previous platforms:
SKL <- APL <- CNL <- ICL <- TGL
rather than putting everything into a single file, the platform-specific
bits are split into cnl/icl/tgl.c files instead. Makes the division clear
and code easier to maintain.
Layout of the patchset:
First are two changes combined together address the sound-clipping
problem, present when only one stream is running - specifically one
CAPTURE stream.
Follow up is naming-scheme adjustment for some of the existing functions
what improves code incohesiveness. As existing IPC/IRQ code operates
solely on cAVS 1.5 architecture, it needs no abstraction. The situation
changes when newer platforms come into the picture. Thus the next two
patches abstract the existing IPC/IRQ handlers so that majority of the
common code can be re-used.
The ICCMAX change stands out a bit - the AudioDSP firmware loading
procedure differs on ICL-based platforms (and onwards) and having a
separate commit makes the situation clear to the developers who are
going to support the solution from LTS perspective. For that reason
I decided not to merge it into the commit introducing the icl.c file.
On my EliteBook 840 G8 Notebook PC (ProdId 5S7R6EC#ABD; built 2022 for
german market) the Mute LED is always on. The mute button itself works
as expected. alsa-info.sh shows a different subsystem-id 0x8ab9 for
Realtek ALC285 Codec, thus the existing quirks for HP 840 G8 don't work.
Therefore, add a new quirk for this type of EliteBook.
Signed-off-by: Hans Peter <flurry123@gmx.ch>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240219164518.4099-1-flurry123@gmx.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Dell Inspiron 16 Plus 7630, similar to its predecessors (7620 models),
experiences an issue with unconnected top speakers. Since the controller
remains unchanged, this commit addresses the problem by correctly
connecting the speakers on NID 0X17 to the DAC on NIC 0x03.
Signed-off-by: Jay Ajit Mate <jay.mate15@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240219100404.9573-1-jay.mate15@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull the latest 6.8 stuff into devel branch for further development.
Fixed the trivial merge conflict for HD-audio Realtek stuff.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP mt645 G7 Thin Client uses an ALC236 codec and needs the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make the mute and
micmute LEDs work.
There are two variants of the USB-C PD chip on this device. Each uses
a different BIOS and board ID, hence the two entries.
Signed-off-by: Eniac Zhang <eniac-xw.zhang@hp.com>
Signed-off-by: Alexandru Gagniuc <alexandru.gagniuc@hp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240215154922.778394-1-alexandru.gagniuc@hp.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A relatively large set of fixes and quirk additions here but they're all
driver specific, people seem to be back into the swing of things after
the holidays. This is all driver specific and much of it fairly minor.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmXOEbkACgkQJNaLcl1U
h9BzgAf/abgoQLJCpvLzEppfOvS3+uXjxZzOeRXcZJXa8a9RIzYx/GQoipsgL8n1
1MpdbKKR63xeGiohASp0nUN6gVgviGZvutgI/+yISxlUktUn/g7P/vz2Zlq+7KMw
T2/Vn3bYFFO2MXUZKaNdfizUVq67zXSNCT/+AAr6AYG//yGy5EfX2BO82vbwZm3e
Yh/fQ3pMrhSI+el9gtSaeXrVs/KOyRDhJamVlE6q78Xm90z6wJ8wov4QTGEn5QjN
8C3axogE4ZsXUsiq7o3G8Tn+YVHIZ10wGHlnSg3bIatn8CEA3kTi/QxboAVDZLeH
0kyy98WPxtzJRYjNsz4YoT8t+He08A==
=0kWz
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.8-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.8
A relatively large set of fixes and quirk additions here but they're all
driver specific, people seem to be back into the swing of things after
the holidays. This is all driver specific and much of it fairly minor.
The patch 51d9760799 ("ALSA: hda/realtek:
Add quirks for ASUS Zenbook 2022 Models") modified the entry 1043:1e2e
from "ASUS UM3402" to "ASUS UM6702RA/RC" and added another entry for
"ASUS UM3402" with 104e:1ee2.
The first entry was correct, while the new one corresponds to model
"ASUS UM6702RA/RC"
Fix the model names for both devices.
Fixes: 51d9760799 ("ALSA: hda/realtek: Add quirks for ASUS Zenbook 2022 Models")
Signed-off-by: Jean-Loïc Charroud <lagiraudiere+linux@free.fr>
Link: https://lore.kernel.org/r/1656546983.650349575.1707867732866.JavaMail.zimbra@free.fr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
clang-16 started warning about incompatible function pointers here:
sound/pci/aw2/aw2-alsa.c:363:11: error: cast from 'void (*)(struct snd_pcm_substream *)' to 'snd_aw2_saa7146_it_cb' (aka 'void (*)(void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
363 | (snd_aw2_saa7146_it_cb)
| ^~~~~~~~~~~~~~~~~~~~~~~
364 | snd_pcm_period_elapsed,
| ~~~~~~~~~~~~~~~~~~~~~~
sound/pci/aw2/aw2-alsa.c:392:10: error: cast from 'void (*)(struct snd_pcm_substream *)' to 'snd_aw2_saa7146_it_cb' (aka 'void (*)(void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
392 | (snd_aw2_saa7146_it_cb)
| ^~~~~~~~~~~~~~~~~~~~~~~
393 | snd_pcm_period_elapsed,
| ~~~~~~~~~~~~~~~~~~~~~~
Add a forward declaration for struct snd_pcm_substrea to allow it to just
use the correct prototype.
Fixes: 98f2a97f20 ("[ALSA] Emagic Audiowerk 2 ALSA driver.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240213101327.460191-1-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver creates an abstraction for different components by casting function
pointers to slightly incompatible types for each one to get the correct
argument even when the caller does not know those types. This is a
bit unreliable and not allowed in combination with control flow integrity
(KCFI):
sound/pci/ctxfi/ctatc.c:115:25: error: cast from 'int (*)(struct hw *, struct src_mgr **)' to 'create_t' (aka 'int (*)(struct hw *, void **)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
115 | [SRC] = { .create = (create_t)src_mgr_create,
| ^~~~~~~~~~~~~~~~~~~~~~~~
sound/pci/ctxfi/ctatc.c:116:20: error: cast from 'int (*)(struct src_mgr *)' to 'destroy_t' (aka 'int (*)(void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
116 | .destroy = (destroy_t)src_mgr_destroy },
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
sound/pci/ctxfi/ctatc.c:117:27: error: cast from 'int (*)(struct hw *, struct srcimp_mgr **)' to 'create_t' (aka 'int (*)(struct hw *, void **)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
117 | [SRCIMP] = { .create = (create_t)srcimp_mgr_create,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/pci/ctxfi/ctatc.c:118:20: error: cast from 'int (*)(struct srcimp_mgr *)' to 'destroy_t' (aka 'int (*)(void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
118 | .destroy = (destroy_t)srcimp_mgr_destroy },
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Change these to always pass void pointers and move the abstraction one level
down.
Fixes: 8cc7236148 ("ALSA: SB X-Fi driver merge")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240213101303.460008-1-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of a few additional bytes for the
state dumps even if it's not really used, but the code simplification
should justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-29-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of all 4 pages no matter with
CONFIG_PM, but the code simplification should justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-28-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
The temporary buffers for PCM stream backups are conditionally
allocated since the sizes aren't too small.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-27-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with an additional allocation of a flag without
CONFIG_PM, but the code simplification should justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-26-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
The area for register dump is conditionally allocated instead of
ifdef now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-25-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of a few additional bytes for the
register dumps even if it's not really used, but the code
simplification should justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-24-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of a few additional bytes for the
register dumps even if it's not really used, but the code
simplification should justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-23-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of a few additional bytes for the
register dumps even if it's not really used, but the code
simplification should justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-22-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of firmware caches if it's not really
used without CONFIG_PM, but the code simplification should justify the
cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-21-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of a few additional bytes for the
register dumps even if it's not really used, but the code
simplification should justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-20-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of a few additional bytes for the
register dumps even if it's not really used, but the code
simplification should justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-19-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of a few additional bytes for the
register dumps even if it's not really used, but the code
simplification should justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-18-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
This ends up with the allocation of a few additional bytes for the
image even if it's not really used, but the code-simplification should
justify the cost.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-17-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of allocating the memory with an additional devm_kmalloc(),
just put the image into the existing struct snd_ali. The allocation
size isn't too big, hence it works better with less allocation calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-16-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
Just a cleanup, no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
Just a cleanup, no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
For building properly, add the dummy functions for
snd_ak4531_suspend/resume() functions, too.
Just a cleanup, no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
Just a cleanup, no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
For building properly, add the dummy functions for
snd_sbmixer_suspend/resume() functions, too.
Just a cleanup, no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new DEFINE_SIMPLE_DEV_PM_OPS() instead of SIMPLE_DEV_PM_OPS()
for code-simplification. We need no longer CONFIG_PM_SLEEP ifdefs.
Just a cleanup, no functional changes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240207155140.18238-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic
CS35L56 amplifier") adds configs SND_HDA_SCODEC_CS35L56_{I2C,SPI},
which selects the non-existing config CS_DSP. Note the renaming in
commit d7cfdf17cb ("firmware: cs_dsp: Rename KConfig symbol CS_DSP ->
FW_CS_DSP"), though.
Select the intended config FW_CS_DSP.
This broken select command probably was not noticed as the configs also
select SND_HDA_CS_DSP_CONTROLS and this then selects FW_CS_DSP. So, the
select FW_CS_DSP could actually be dropped, but we will keep this
redundancy in place as the author originally also intended to have this
redundancy of selects in place.
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Simon Trimmer <simont@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240209082044.3981-1-lukas.bulwahn@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The tascodec_init() of the snd-soc-tas2781-comlib module is called from
snd-soc-tas2781-i2c and snd-hda-scodec-tas2781-i2c modules. It calls
request_firmware_nowait() with parameter THIS_MODULE and a cont/callback
from the latter modules.
The latter modules can be removed while their callbacks are running,
resulting in a general protection failure.
Add module parameter to tascodec_init() so request_firmware_nowait() can
be called with the module of the callback.
Fixes: ef3bcde75d ("ASoC: tas2781: Add tas2781 driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/118dad922cef50525e5aab09badef2fa0eb796e5.1707076603.git.soyer@irl.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
The SWS JS201D need a different pinconfig from windows driver.
Add a quirk to use a specific pinconfig to SWS JS201D.
Signed-off-by: bo liu <bo.liu@senarytech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240205013802.51907-1-bo.liu@senarytech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SKUs, and associated SSIDs, are no longer going to include the
CS35L41. They may come back, but will need a different quirk.
Fixes: aa8e3ef4fe ("ALSA: hda/realtek: Add quirks for various HP ENVY models")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240202170842.321818-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This pull request adds Richard Fitzgerald's series with extensive fixes
for the CS35L56, he said:
These patches fix various things that were undocumented, unknown or
uncertain when the original driver code was written. And also a few
things that were just bugs.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmW75GkACgkQJNaLcl1U
h9CBhAf/an09YRBuVTbep/g7a6D+NTuMRY/iDJBlBcukk4NED45r0zrS/JgCQU8S
iWk6uAMbl3ato7P8zn99eQCcTAS6/fhkQIeiHwOg+AAvKBQ62tlAt5NsTXs/QLWh
AI04UwAf+CPIvO8kngu4bhEOH5X0Ss7lr5NzpmO/vVJODX6i5BbpiWiAxIn5yt7V
17SrpKzsp9yv/OyDrqmrhoT2cECNir1sBdTgMj+7L1+2URRd7gx4xFipmS3Cu6KE
FP+wBtoDa4HQ7RK2O/uPhmjpbBAF12maIc0XEdDg/VTIRhxHTUK+9e7kfxkkpn0z
6B9vx7xr3GkvcFcXJo23hC0jUn/1ZA==
=z/HP
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.8-rc2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.8
This pull request adds Richard Fitzgerald's series with extensive fixes
for the CS35L56, he said:
These patches fix various things that were undocumented, unknown or
uncertain when the original driver code was written. And also a few
things that were just bugs.
Vaio VJFE-ADL is equipped with ALC269VC, and it needs
ALC298_FIXUP_SPK_VOLUME quirk to make its headset mic work.
Signed-off-by: Edson Juliano Drosdeck <edson.drosdeck@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240201122114.30080-1-edson.drosdeck@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove an unused stub function that calls a non-existant function.
This function was accidentally added as part of commit
2144833e7b ("ALSA: hda: cirrus_scodec: Add KUnit test"). It was
a relic of an earlier version of the test that should have been
removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2144833e7b ("ALSA: hda: cirrus_scodec: Add KUnit test")
Link: https://msgid.link/r/20240129162737.497-19-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check whether the firmware is already patched. If so, include the
firmware version in the firmware file name.
If the firmware has already been patched by the BIOS the driver
can only replace it if it has control of hard RESET.
If the driver cannot replace the firmware, it can still load a wmfw
(for ALSA control definitions) and/or a bin (for additional tunings).
But these must match the version of firmware that is running on the
CS35L56.
The firmware is pre-patched if either:
- FIRMWARE_MISSING == 0, or
- it is a secured CS35L56 (which implies that is was already patched),
cs35l56_hw_init() will set preloaded_fw_ver to the (non-zero)
firmware version if either of these conditions is true.
Normal (unpatched or replaceable firmware):
cs35l56-rev-dsp1-misc[-system_name].[wmfw|bin]
Preloaded firmware:
cs35l56-rev[-s]-VVVVVV-dsp1-misc[-system_name].[wmfw|bin]
Where:
[-s] is an optional -s added into the name for a secured CS35L56
VVVVVV is the 24-bit firmware version in hexadecimal.
Backport note:
This won't apply to kernel versions older than v6.6.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://msgid.link/r/20240129162737.497-18-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the filename field layout to:
cs35l56-rev[-s]-dsp1-misc[-sub].[wmfw|bin]
This is to keep the same firmware file naming scheme as the
CS35L56 ASoC driver.
This is not a compatibility break because no firmware files have
been published.
The original field layout matched the ASoC driver, but the way the
ASoC driver used the wm_adsp driver config to form this filename
was bugged. Fixing the ASoC driver to use the correct wm_adsp config
strings means that the 's' flag (to indicate a secured part) has to
move to somewhere after the first '-'.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://msgid.link/r/20240129162737.497-17-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for the cases of system-specific bin file without a
wmfw before falling back to looking for a generic wmfw.
All system-specific options should be tried before falling
back to loading a generic wmfw/bin. With the original code,
the presence of a fallback generic wmfw on the filesystem
would prevent using a system-specific tuning with a ROM
firmware.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://msgid.link/r/20240129162737.497-16-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ASP1_FRAME_CONTROL1, ASP1_FRAME_CONTROL5 and the ASP1_TX?_INPUT
registers to the sequence used to initialize the ASP configuration.
Write this sequence to the cache and directly to the registers to
ensure that they match.
A system-specific firmware can patch these registers to values that are
not the silicon default, so that the CS35L56 boots already in the
configuration used by Windows or by "driverless" Windows setups such
as factory tuning.
These may not match how Linux is configuring the HDA codec. And anyway
on Linux the ALSA controls are used to configure routing options.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://msgid.link/r/20240129162737.497-10-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There currently exists two thinkpad headset jack fixups:
ALC285_FIXUP_THINKPAD_NO_BASS_SPK_HEADSET_JACK
ALC285_FIXUP_THINKPAD_HEADSET_JACK
The latter is applied to alc285 and alc287 thinkpads which contain
bass speakers.
However, the former was only being applied to alc285 thinkpads,
leaving non-bass alc287 thinkpads with no headset button controls.
This patch fixes that by adding ALC285_FIXUP_THINKPAD_NO_BASS_SPK_HEADSET_JACK
to the alc287 chains, allowing the detection of headset buttons.
Signed-off-by: José Relvas <josemonsantorelvas@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240131113407.34698-3-josemonsantorelvas@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This HP Laptop uses ALC236 codec with COEF 0x07 controlling the
mute LED. Enable existing quirk for this device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240128155704.2333812-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If you connect an external headset/microphone to the 3.5mm jack on the
Acer Swift 1 SF114-32 it does not recognize the microphone. This fixes
that and gives the user the ability to choose between internal and
headset mic.
Signed-off-by: David Senoner <seda18@rolmail.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240126155626.2304465-1-seda18@rolmail.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Laptops 103C8C66, 103C8C67, 103C8C68, 103C8C6A use a dual speaker id
system where each speaker has its own speaker id.
The generic configuration table doesn't support this, so it needs its
own function.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240126164005.367021-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current method to set Channel Index when the system is missing _DSD
assumes that the channels alternate, which is not guaranteed.
Instead use the same methodology as the main driver does when _DSD
exists.
Fixes: 8c4c216db8 ("ALSA: hda: cs35l41: Add config table to support many laptops without _DSD")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240126164005.367021-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add quirks for two HP G11 laptops that use a Realtek HDA codec combined
with four CS35L56 amplifiers using SPI.
The CS35L56 driver uses the component binding interface, so uses the same
setup code as the CS35L41 quirks.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240125123301.41692-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the generic parts of the hda_component implementation into a new
hda_component module. This will allow other HDA codecs to add support
for the component binding API without duplicating all the code.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Tested-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/20240124112607.77614-3-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Slightly re-work the code around cs35l41_generic_fixup() and the component
binding search so that it can be re-used for other amps that use the
component binding mechanism.
The match string is stored in struct scodec_dev_name instead of hardcoding
it in the match function.
The tas2781 does not use the amp index as part of the driver name match.
But its match format string does not include a field for the index, so
snprintf() would safely ignore the p->index argument. Because of this there
is no need for a special match function for this case, the CS35L41 code
can be re-used.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Tested-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/20240124112607.77614-2-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SSID 0x0c0d platform. It can't mute speaker when HP plugged.
This patch add quirk to fill speaker pin verbtable.
And disable speaker passthrough.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/38b82976a875451d833d514cee34ff6a@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Customer has reported an issue with specific desktop platform
where two CS42L42 codecs are connected to CS8409 HDA bridge.
If "Master Volume Control" is created then on Ubuntu OS UCM
left/right balance slider in UI audio settings has no effect.
This patch will fix this issue for a target paltform.
Fixes: 20e5077241 ("ALSA: hda/cs8409: Add support for dolphin")
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240122184710.5802-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apollo Lake seems to also suffer from IRQ timing issues. After being up for ~4
minutes, a Pentium N4200 system ends up falling back to workqueue-based IRQ
handling:
[ 208.019906] snd_hda_intel 0000:00:0e.0: IRQ timing workaround is activated
for card #0. Suggest a bigger bdl_pos_adj.
Unfortunately, the Baytrail and Braswell workaround value of 32 samples isn't
enough to fix the issue here. Default to 64 samples.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240122114512.55808-3-rsalvaterra@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have self-explanatory constants for Intel HDA devices, let's use them instead
of magic numbers and code comments.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240122114512.55808-2-rsalvaterra@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP ZBook Power using ALC236 codec which using 0x02 to
control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240122074826.1020964-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of small fixes:
- Lots of ASoC SOF fixes and related reworks
- ASoC TAS codec fixes including DT updates
- A few HD-audio quirks and regression fixes
- Minor fixes for aloop, oxygen and scarlett2 mixer
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmWqn98OHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE/wIBAArdsfEKeNgeH2Ta939koBiWknCXT12nMd+rgi
ZywjXrK7gJZKuuRYV0CKSlXl7yJD1jhbt7kG5/RyQaTZuuqEny/nwokqQrgZnf+Z
mz1D0naIKORXLdKVD9YcN9F85z2D0WToEhbg8HyBgO3BIJKpEP+7ggBQO7zz19Gx
BsrJsR0X1OUDVz90ltMmvohgj3WeIQ0lIs3cCdORylXq2MPAonqbHv6fYPoGupfi
Vyx4mSkowBQRl9zVAuT5yKRZcqUbrZXfumHTiPDNDu3veIzZ0JtXaGMWic9a/g3T
q+4lvNI7+oT1ObIi1zXeBfll9k0khjKvj/d1MEH4mJYrNKnrZBkDHNTu87x5lwyU
WXcbGl8QgOS+x7t52CKKymBZbIQ7OJPkwSWK3G6zrblRbYZ805W5Kn3zMlNvVY4F
XAzxxwkhU2uraya+CSuiDnGPJ3OHxbjnsQplDjUXXm2JipC9+9TrorGuxZ/3LVkj
736ShKmfuUh/qAXuITd4QHGa/M3N7xq9jINQrWOjHJoEznC2rLfuVzLlsOU26Z29
NfrHuq0JACu1ed2xl4Kk6GVuBGSXnu1fQYGd/6U7U14CZnoG2hOwqVaq4Qx+ce1Z
G37tcM9sISoCm6lPxotd+Aeu38s2dC+Ju5b3lKIKqxVLygJjSjUjiggJLatB8Bip
zZ4ZH1g=
=h9S1
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes:
- Lots of ASoC SOF fixes and related reworks
- ASoC TAS codec fixes including DT updates
- A few HD-audio quirks and regression fixes
- Minor fixes for aloop, oxygen and scarlett2 mixer"
* tag 'sound-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: hda/realtek: Enable headset mic on Lenovo M70 Gen5
ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on HP ZBook
ALSA: hda/relatek: Enable Mute LED on HP Laptop 15s-fq2xxx
ASoC: SOF: ipc4-loader: remove the CPC check warnings
ASoC: SOF: ipc4-pcm: remove log message for LLP
ALSA: hda: generic: Remove obsolete call to ledtrig_audio_get
ALSA: scarlett2: Fix yet more -Wformat-truncation warnings
ALSA: hda: Properly setup HDMI stream
ASoC: audio-graph-card2: fix index check on graph_parse_node_multi_nm()
ASoC: SOF: icp3-dtrace: Revert "Fix wrong kfree() usage"
ALSA: oxygen: Fix right channel of capture volume mixer
ALSA: aloop: Introduce a function to get if access is interleaved mode
ASoC: mediatek: sof-common: Add NULL check for normal_link string
ASoC: mediatek: mt8195: Remove afe-dai component and rework codec link
ASoC: mediatek: mt8192: Check existence of dai_name before dereferencing
ASoC: Intel: bxt_rt298: Fix kernel ops due to COMP_DUMMY change
ASoC: Intel: bxt_da7219_max98357a: Fix kernel ops due to COMP_DUMMY change
ASoC: codecs: rtq9128: Fix TDM enable and DAI format control flow
ASoC: codecs: rtq9128: Fix PM_RUNTIME usage
ASoC: tas2781: Add tas2563 into driver
...
Lenovo M70 Gen5 is equipped with ALC623, and it needs
ALC283_FIXUP_HEADSET_MIC quirk to make its headset mic work.
Signed-off-by: Bin Li <bin.li@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240117154123.21578-1-bin.li@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some HP ZBooks, the audio LEDs can be enabled by
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF. So use it accordingly.
Signed-off-by: Yo-Jung Lin <leo.lin@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240116020722.27236-1-leo.lin@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This HP Laptop uses ALC236 codec with COEF 0x07 idx 1 controlling
the mute LED. This patch enables the already existing quirk for
this device.
Signed-off-by: Çağhan Demir <caghandemir@marun.edu.tr>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240115172303.4718-1-caghandemir@marun.edu.tr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since 64f67b5240 ("leds: trigger: audio: Add an activate callback to
ensure the initial brightness is set") the audio triggers have an
activate callback which sets the LED brightness as soon as the
(default) trigger is bound to the LED device. So we can remove the
call to ledtrig_audio_get.
Positive side effect: We have no code dependency to ledtrig-audio any
longer, therefore, if built as module, it's no longer loaded if not
needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/3dc9167d-fb33-43a6-baa6-dbef8b5da7b9@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It was a clam development cycle. There were an ALSA core extension
for subformat PCM bits and a few ASoC core changes to support N:M
mappings, while the most of remaining changes are driver-specific.
Core:
- API extensions for properly limiting PCM format bits via subformat
- Enhanced support for N:M CPU:CODEC mappings in the core and in
audio-graph-card2
ASoC:
- Lots of SOF updates: fallback support to older IPC versions,
notification on control changes with IPC4.
Also supports for ACPI parse for the ES83xx driver that reduces
quirks.
- Device tree support for describing parts of the card which can be
active over suspend (for very low power playback or wake word use
cases)
- Support for more AMD and Intel systems, NXP i.MX8m MICFIL, Qualcomm
SM8250, SM8550, SM8650 and X1E80100
- Drop of Freescale MPC8610 code that is no longer supported
HD-audio:
- More CS35L41 codec extensions for Dell, HP and Lenovo models
- TAS2781 codec extensions for Lenovo and co
- New PCM subformat supports
Others:
- More enhancement for Scarlett2 USB mixer support
- Various kselftest fixes
-----BEGIN PGP SIGNATURE-----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=yVxc
-----END PGP SIGNATURE-----
Merge tag 'sound-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It was a calm development cycle. There were an ALSA core extension for
subformat PCM bits and a few ASoC core changes to support N:M
mappings, while the most of remaining changes are driver-specific.
Core:
- API extensions for properly limiting PCM format bits via subformat
- Enhanced support for N:M CPU:CODEC mappings in the core and in
audio-graph-card2
ASoC:
- Lots of SOF updates: fallback support to older IPC versions,
notification on control changes with IPC4. Also supports for ACPI
parse for the ES83xx driver that reduces quirks.
- Device tree support for describing parts of the card which can be
active over suspend (for very low power playback or wake word use
cases)
- Support for more AMD and Intel systems, NXP i.MX8m MICFIL, Qualcomm
SM8250, SM8550, SM8650 and X1E80100
- Drop of Freescale MPC8610 code that is no longer supported
HD-audio:
- More CS35L41 codec extensions for Dell, HP and Lenovo models
- TAS2781 codec extensions for Lenovo and co
- New PCM subformat supports
Others:
- More enhancement for Scarlett2 USB mixer support
- Various kselftest fixes"
* tag 'sound-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (337 commits)
kselftest/alsa - conf: Stringify the printed errno in sysfs_get()
kselftest/alsa - mixer-test: Fix the print format specifier warning
kselftest/alsa - mixer-test: Fix the print format specifier warning
kselftest/alsa - mixer-test: fix the number of parameters to ksft_exit_fail_msg()
ALSA: hda/tas2781: annotate calibration data endianness
ALSA: hda/realtek: Fix mute and mic-mute LEDs for HP Envy X360 13-ay0xxx
ALSA: hda/conexant: Fix headset auto detect fail in cx8070 and SN6140
ALSA: ac97: fix build regression
ALSA: hda: cs35l41: Support more HP models without _DSD
ALSA: hda/tas2781: add fixup for Lenovo 14ARB7
ALSA: hda/tas2781: add TAS2563 support for 14ARB7
ALSA: hda/tas2781: add configurable global i2c address
ALSA: hda/tas2781: add ptrs to calibration functions
ALSA: hda: Add driver properties for cs35l41 for Lenovo Legion Slim 7 Gen 8 serie
ALSA: hda/realtek: enable SND_PCI_QUIRK for Lenovo Legion Slim 7 Gen 8 (2023) serie
ALSA: hda/tas2781: configure the amp after firmware load
ALSA: mark all struct bus_type as const
ASoC: pxa: sspa: Don't select SND_ARM
ASoC: rt5663: cancel the work when system suspends
ALSA: scarlett2: Add PCM Input Switch for Solo Gen 4
...
Since commit 4005d1ba0a ("ASoC: soc-dai: don't call PCM audio ops if
the stream is not supported") HDMI playback is broken with avs driver.
This happens because for HDMI stream (unlike generic HDA one)
channels_min for stream is not set when creating PCMs. Fix this by
setting the value based on first available converter.
Fixes: 4005d1ba0a ("ASoC: soc-dai: don't call PCM audio ops if the stream is not supported")
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240112113349.2905328-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A moderately busy release for SPI, the main core update was the merging
of support for multiple chip selects, used in some flash configurations.
There were also big overhauls for the AXI SPI Engine and PL022 drivers,
plus some new device support for ST.
There's a few patches for other trees, API updates to allow the
multiple chip select support and one of the naming modernisations
touched a controller embedded in the USB code.
- Support for multiple chip selects.
- A big overhaul for the AXI SPI engine driver, modernising it and
adding a bunch of new features.
- Modernisation of the PL022 driver, fixing some issues with submitting
messages while in atomic context in the process.
- Many drivers were converted to use new APIs which avoid outdated
terminology for devices and controllers.
- Support for ST Microelectronics STM32F7 and STM32MP25, and Renesas
RZ/Five.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmWbHmMACgkQJNaLcl1U
h9CpSwf+O981469g1twyEpq5PJlNgdXmrKUpezcC18X4DLXmlf5hoCsHUFIU2DuX
oBZuUQVp1KaEzJ4LX1giAOTuhfwPAItGR+/JMs6VxT/V0MMCHaNYcU5zLHXacDFL
URU7hyyhxUp9PzGNI/IEQH2DPv3QVX8Z1CVQQNQpnTsvbpBEF/osxB3SdWg65Y4J
B9nEW5hnyDsjxQVzjwCMFsy1vJeaBkP++zdPhPGE4RaNcweX+hksVRWVJ3DqUuJC
u4IyO5Hmduqmyjyc7MEV6lekecnyHc72WIzFXJpy0FOW0CstOQD59D5Fnbdvbb9i
mm3IJ1Vh/oepZBNPAmHCPqMEAqr5ZQ==
=49Kh
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A moderately busy release for SPI, the main core update was the
merging of support for multiple chip selects, used in some flash
configurations. There were also big overhauls for the AXI SPI Engine
and PL022 drivers, plus some new device support for ST.
There's a few patches for other trees, API updates to allow the
multiple chip select support and one of the naming modernisations
touched a controller embedded in the USB code.
- Support for multiple chip selects.
- A big overhaul for the AXI SPI engine driver, modernising it and
adding a bunch of new features.
- Modernisation of the PL022 driver, fixing some issues with
submitting messages while in atomic context in the process.
- Many drivers were converted to use new APIs which avoid outdated
terminology for devices and controllers.
- Support for ST Microelectronics STM32F7 and STM32MP25, and Renesas
RZ/Five"
* tag 'spi-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (83 commits)
spi: stm32: add st,stm32mp25-spi compatible supporting STM32MP25 soc
dt-bindings: spi: stm32: add st,stm32mp25-spi compatible
spi: stm32: use dma_get_slave_caps prior to configuring dma channel
spi: axi-spi-engine: fix struct member doc warnings
spi: pl022: update description of internal_cs_control()
spi: pl022: delete description of cur_msg
spi: dw: Remove Intel Thunder Bay SOC support
spi: dw: Remove Intel Thunder Bay SOC support
spi: sh-msiof: Enforce fixed DTDL for R-Car H3
spi: ljca: switch to use devm_spi_alloc_host()
spi: cs42l43: switch to use devm_spi_alloc_host()
spi: zynqmp-gqspi: switch to use modern name
spi: zynq-qspi: switch to use modern name
spi: xtensa-xtfpga: switch to use modern name
spi: xlp: switch to use modern name
spi: xilinx: switch to use modern name
spi: xcomm: switch to use modern name
spi: uniphier: switch to use modern name
spi: topcliff-pch: switch to use modern name
spi: wpcm-fiu: switch to use devm_spi_alloc_host()
...
When OMTP headset plugin the headset jack of CX8070 and SN6160 sound cards,
the headset type detection circuit will recognize the headset type as CTIA.
At this point, plugout and plugin the headset will get the correct headset
type as OMTP.
The reason for the failure of headset type recognition is that the sound
card creation will enable the VREF voltage of the headset mic, which
interferes with the headset type automatic detection circuit. Plugout and
plugin the headset will restart the headset detection and get the correct
headset type.
The patch is disable the VREF voltage when the headset is not present, and
will enable the VREF voltage when the headset is present.
Signed-off-by: bo liu <bo.liu@senarytech.com>
Link: https://lore.kernel.org/r/20240108110235.3867-1-bo.liu@senarytech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_SPI is disabled, the driver produces unused-variable warning:
sound/pci/hda/cs35l41_hda_property.c: In function 'generic_dsd_config':
sound/pci/hda/cs35l41_hda_property.c:181:28: error: unused variable 'spi' [-Werror=unused-variable]
181 | struct spi_device *spi;
| ^~~
sound/pci/hda/cs35l41_hda_property.c:180:27: error: unused variable 'cs_gpiod' [-Werror=unused-variable]
180 | struct gpio_desc *cs_gpiod;
| ^~~~~~~~
Avoid these by turning the preprocessor contionals into equivalent C code,
which also helps readability.
Fixes: 916d051730 ("ALSA: hda: cs35l41: Only add SPI CS GPIO if SPI is enabled in kernel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240103102606.3742476-1-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds overrides for a series of notebooks using a common config
taken from HP's proprietary Windows driver.
This has been tested on a HP 15-ey0xxxx device (subsystem 103C8A31)
together with another Realtek quirk and the calibration files from the
proprietary driver.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Cc: <stable@vger.kernel.org> # v6.7
Link: https://lore.kernel.org/r/20240102214821.3394810-1-lorenz@brun.one
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a HP ZBook which using ALC236 codec and need the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make mute LED
and micmute LED work.
[ confirmed that the new entries are for new models that have no
proper name, so the strings are left as "HP" which will be updated
eventually later -- tiwai ]
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240102024916.19093-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add driver properties on 4 models of this laptop serie since they don't
have _DSD in the ACPI table
Signed-off-by: Dorian Cruveiller <doriancruveiller@gmail.com>
Cc: <stable@vger.kernel.org> # v6.7
Link: https://lore.kernel.org/r/20231230114312.22118-1-doriancruveiller@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Pavilion 14 ec1xxx series uses the HP mainboard 8A0F with the
ALC287 codec.
The mute led can be enabled using the already existing
ALC287_FIXUP_HP_GPIO_LED quirk.
Tested on an HP Pavilion ec1003AU
Signed-off-by: Aabish Malik <aabishmalik3337@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231229170352.742261-3-aabishmalik3337@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2 or 4 CS35L41 amps with HDA using SPI and I2C.
Models use internal and external boost.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v6.7+
Link: https://lore.kernel.org/r/20231221132518.3213-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops without _DSD have the SPI speed set very low in the BIOS.
Since the SPI controller uses this speed as its max speed, the SPI
transactions are very slow. Firmware download writes to many registers,
and if the SPI speed is too slow, it can take a long time to download.
For this reason, disable firmware loading if the maximum SPI speed is
too low. Without Firmware, audio playback will work, but the volume
will be low to ensure safe operation of the CS35L41.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v6.7+
Link: https://lore.kernel.org/r/20231221132518.3213-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two problems with using regcache in this module.
The amplifier has 3 addressing levels (BOOK, PAGE, REG). The firmware
contains blocks that must be written to BOOK 0x8C. The regcache doesn't
know anything about BOOK, so regcache_sync writes invalid values to the
actual BOOK.
The module handles 2 or more separate amplifiers. The amplifiers have
different register values, and the module uses only one regmap/regcache
for all the amplifiers. The regcache_sync only writes the last amplifier
used.
The module successfully restores all the written register values (RC
profile, program, configuration, calibration) without regcache.
Remove regcache functions and set regmap cache_type to REGCACHE_NONE.
Link: https://lore.kernel.org/r/21a183b5a08cb23b193af78d4b1114cc59419272.1701906455.git.soyer@irl.hu/
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Acked-by: Mark Brown <broonie@kernel.org>
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/491aeed0e2eecc3b704ec856f815db21bad3ba0e.1703202126.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialise the variables to NULL so that they cannot be uninitialised
when devm_kfree is called.
Found by static analysis.
Fixes: 8c4c216db8 ("ALSA: hda: cs35l41: Add config table to support many laptops without _DSD")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231219162232.790358-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2xCS35L41amps with HDA using SPI and I2C.
Models use internal and external boost.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2xCS35L41amps with HDA using SPI and I2C.
Models use internal and external boost.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2xCS35L41amps with HDA using SPI and I2C.
All models use Internal Boost.
Some models also use Realtek Speakers in conjunction with
CS35L41.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This make use of the CS35L41 HDA Property framework, which supports
laptops which do not have the _DSD properties in their ACPI.
Add configuration table to be able to use a generic function which allows
laptops to be supported just by adding an entry into the table.
Use configuration table function for existing system 103C89C6.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, cur_prog/cur_conf remains at the default value (-1), while
program 0 has been loaded into the amplifiers.
In the playback hook, tasdevice_tuning_switch tries to restore the
cur_prog/cur_conf. In the runtime_resume/system_resume,
tasdevice_prmg_load tries to load the cur_prog as well.
Set cur_prog and cur_conf to 0 if available in the firmware.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/038add0bdca1f979cc7abcce8f24cbcd3544084b.1702596646.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Calling component_add starts loading the firmware, the callback function
writes the program to the amplifiers. If the module resets the
amplifiers after component_add, it happens that one of the amplifiers
does not work because the reset and program writing are interleaving.
Call tas2781_reset before component_add to ensure reliable
initialization.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/4d23bf58558e23ee8097de01f70f1eb8d9de2d15.1702511246.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the module can load the RCA but not the firmware binary, it will call
the cleanup functions. Then unloading the module causes general
protection fault due to double free.
Do not call the cleanup functions in tasdev_fw_ready.
general protection fault, probably for non-canonical address
0x6f2b8a2bff4c8fec: 0000 [#1] PREEMPT SMP NOPTI
Call Trace:
<TASK>
? die_addr+0x36/0x90
? exc_general_protection+0x1c5/0x430
? asm_exc_general_protection+0x26/0x30
? tasdevice_config_info_remove+0x6d/0xd0 [snd_soc_tas2781_fmwlib]
tas2781_hda_unbind+0xaa/0x100 [snd_hda_scodec_tas2781_i2c]
component_unbind+0x2e/0x50
component_unbind_all+0x92/0xa0
component_del+0xa8/0x140
tas2781_hda_remove.isra.0+0x32/0x60 [snd_hda_scodec_tas2781_i2c]
i2c_device_remove+0x26/0xb0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/1a0885c424bb21172702d254655882b59ef6477a.1702510018.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code does not properly check whether the calibration variable is
available in the EFI. If it is not available, it causes a NULL pointer
dereference.
Check the return value of the first get_variable call also.
BUG: kernel NULL pointer dereference, address: 0000000000000000
Call Trace:
<TASK>
? __die+0x23/0x70
? page_fault_oops+0x171/0x4e0
? srso_alias_return_thunk+0x5/0x7f
? schedule+0x5e/0xd0
? exc_page_fault+0x7f/0x180
? asm_exc_page_fault+0x26/0x30
? crc32_body+0x2c/0x120
? tas2781_save_calibration+0xe4/0x220 [snd_hda_scodec_tas2781_i2c]
tasdev_fw_ready+0x1af/0x280 [snd_hda_scodec_tas2781_i2c]
request_firmware_work_func+0x59/0xa0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/f1f6583bda918f78556f67d522ca7b3b91cebbd5.1702251102.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP laptop 15-db0403ng uses the ALC236 codec and controls the mute
LED using COEF 0x07 index 1.
Sound card subsystem: Hewlett-Packard Company Device [103c:84ae]
Use the existing quirk for this model.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e61815d0-f1c7-b164-e49d-6ca84771476a@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On ASUSTeK Z170M PLUS and Z170 PRO GAMING systems, the display codec
pins are not registered properly without the force-connect quirk. The
codec will report only one pin as having external connectivity, but i915
finds all three connectors on the system, so the two drivers are not
in sync.
Issue found with DRM igt-gpu-tools test kms_hdmi_inject@inject-audio.
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/9801
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231208132127.2438067-3-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add one more older NUC model that requires quirk to force all pins to be
connected. The display codec pins are not registered properly without
the force-connect quirk. The codec will report only one pin as having
external connectivity, but i915 finds all three connectors on the
system, so the two drivers are not in sync.
Issue found with DRM igt-gpu-tools test kms_hdmi_inject@inject-audio.
Link: https://gitlab.freedesktop.org/drm/igt-gpu-tools/-/issues/3
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231208132127.2438067-2-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
This patch series adds support to the SPI framework for using multiple
chip selects.
In preparation for adding multiple CS support for a device, set/get
functions were introduces accessing spi->chip_select in
'commit 303feb3cc0 ("spi: Add APIs in spi core to set/get
spi->chip_select and spi->cs_gpiod")'.
Replace spi->chip_select with spi_get_chipselect() API.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20231125092137.2948-3-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Framework 16" laptop has the same controller as other Framework
models. Apply the presence detection quirk.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231206193927.2996-1-mario.limonciello@amd.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Framework Laptop 13 (AMD Ryzen 7040Series) has an ALC295 with
a disconnected or faulty headset mic presence detect similar to the
previous models. It works with the same quirk chain as
309d7363ca. This model has a VID:PID
of f111:0006.
Signed-off-by: Tim Bosse <flinn@timbos.se>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231206142629.388615-1-flinn@timbos.se
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo M90 Gen5 is equipped with ALC897, and it needs
ALC897_FIXUP_HEADSET_MIC_PIN quirk to make its headset mic work.
Signed-off-by: Bin Li <bin.li@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231204100450.642783-1-bin.li@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
XPS 9530 has 2 tweeters and 2 subwoofers powered by CS35L41 amplifier, SPI
connected. For subwoofers to work, it requires both to enable amplifier
support, and to enable output to subwoofers via 0x17 quirk (similalry to
XPS 9510/9520).
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231203233006.100558-1-alex.vinarskis@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS UM3504DA uses a Realtek HDA codec and two CS35L41 amplifiers via I2C.
Apply existing quirk to model.
Signed-off-by: Pascal Noël <pascal@pascalcompiles.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231202013744.12369-1-pascal@pascalcompiles.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's been reported that the runtime PM on KONTRON SinglePC (PCI SSID
1734:1232) caused a stall of playback after a bunch of invocations.
(FWIW, this looks like an timing issue, and the stall happens rather
on the controller side.)
As a workaround, disable the default power-save on this platform.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231130151321.9813-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To provide option for selecting different bit-per-sample than just the
maximum one, use the new format calculation mechanism.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20231117120610.1755254-8-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To provide option for selecting different bit-per-sample than just the
maximum one, use the new format calculation mechanism.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20231117120610.1755254-7-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To provide option for selecting different bit-per-sample than just the
maximum one, use the new format calculation mechanism.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20231117120610.1755254-6-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update mechanism for querying supported PCMs to allow for granular
format selection when container size is 32 bits. Currently always the
highest bit depth is selected, regardless of how many actual formats
codec in question supports.
Acked-by: Mark Brown <broonie@kernel.org>
Co-developed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20231117120610.1755254-3-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SPI hibernation is now supported with the latest hibernation/wake
sequences in the shared ASoC code.
This has a functional dependency on two commits:
commit 3df761bdbc ("ASoC: cs35l56: Wake transactions need to be issued
twice")
commit a47cf4dac7 ("ASoC: cs35l56: Change hibernate sequence to use
allow auto hibernate")
To protect against this, enabling hibernation is conditional on
CS35L56_WAKE_HOLD_TIME_US being defined, which indicates that the new
hibernation sequences are available.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231121154419.19435-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some older laptops using cs35l41 use firmware which does not support
the CSPL_MBOX_CMD_SPK_OUT_ENABLE command.
Firmware versions v0.28.0 and older do not support this command.
Fixes: fa3efcc36a ("ALSA: cs35l41: Use mbox command to enable speaker output for external boost")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231117163609.823627-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This state duplicates the running state inside cs_dsp, so is not necessary.
Remove it, and use cs_dsp.running instead.
This brings the CS35L41 HDA driver more inline with its ASoC version,
allowing the same state to be used when calling library functions.
Fixes: fa3efcc36a ("ALSA: cs35l41: Use mbox command to enable speaker output for external boost")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231117163609.823627-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of small fixes: including a regression fix in RC1
wrt HD-audio / i915 component binding, while the rest are HD-audio
device-speific fixes / quirks.
-----BEGIN PGP SIGNATURE-----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=JybD
-----END PGP SIGNATURE-----
Merge tag 'sound-6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes: including a regression fix in RC1 wrt
HD-audio / i915 component binding, while the rest are HD-audio
device-speific fixes / quirks"
* tag 'sound-6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add quirks for HP Laptops
ALSA: hda/realtek: Add quirks for ASUS 2024 Zenbooks
ALSA: hda: i915: Alays handle -EPROBE_DEFER
ALSA: hda/realtek: Enable Mute LED on HP 255 G10
ALSA: hda: cs35l56: Enable low-power hibernation mode on i2c
ALSA: hda/realtek - Enable internal speaker of ASUS K6500ZC
ALSA: hda/realtek: Enable Mute LED on HP 255 G8
ALSA: hda/realtek - Add Dell ALC295 to pin fall back table
These HP laptops use Realtek HDA codec combined with 2 or 4 CS35L41
Amplifiers using SPI with Internal Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231115162116.494968-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These ASUS Zenbook laptops use Realtek HDA codec combined with
2xCS35L41 Amplifiers using SPI or I2C with External Boost or
Internal Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231115162116.494968-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP 255 G10 has a mute LED that can be made to work using quirk
ALC236_FIXUP_HP_MUTE_LED_COEFBIT2.
Enable already existing quirk - at correct line to keep order
Signed-off-by: Matus Malych <matus@malych.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231114133524.11340-1-matus@malych.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This can now be re-enabled as the sequence to reliably wake the device
has been implemented in the shared ASoC code.
This has a functional dependency on commit 3df761bdbc
("ASoC: cs35l56: Wake transactions need to be issued twice")
To protect against this, enabling hibernation is conditional on
CS35L56_WAKE_HOLD_TIME_US being defined, which indicates that the new
hibernation sequences are available.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231113164029.1156669-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of fixes for RC1. Majority of changes are various
ASoC driver-specific small fixes and usual HD-audio quirks, while
there are a couple of core changes: a fix in ALSA core procfs code
to avoid deadlocks at disconnection and an ASoC core fix for DAPM
clock widgets.
-----BEGIN PGP SIGNATURE-----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=6iW2
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fixes for rc1.
The majority of changes are various ASoC driver-specific small fixes
and usual HD-audio quirks, while there are a couple of core changes: a
fix in ALSA core procfs code to avoid deadlocks at disconnection and
an ASoC core fix for DAPM clock widgets"
* tag 'sound-fix-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
OSS: dmasound/paula: Convert to platform remove callback returning void
ALSA: hda: ASUS UM5302LA: Added quirks for cs35L41/10431A83 on i2c bus
ALSA: info: Fix potential deadlock at disconnection
ASoC: nau8540: Add self recovery to improve capture quility
ALSA: hda/realtek: Add support dual speaker for Dell
ALSA: hda: Add ASRock X670E Taichi to denylist
ALSA: hda/realtek: Add quirk for ASUS UX7602ZM
ASoC: SOF: sof-client: trivial: fix comment typo
ASoC: dapm: fix clock get name
ASoC: hdmi-codec: register hpd callback on component probe
ASoC: mediatek: mt8186_mt6366_rt1019_rt5682s: trivial: fix error messages
ASoC: da7219: Improve system suspend and resume handling
ASoC: codecs: Modify macro value error
ASoC: codecs: Modify the wrong judgment of re value
ASoC: codecs: Modify the maximum value of calib
ASoC: amd: acp: fix for i2s mode register field update
ASoC: codecs: aw88399: Fix -Wuninitialized in aw_dev_set_vcalb()
ASoC: rt712-sdca: fix speaker route missing issue
ASoC: rockchip: Fix unused rockchip_i2s_tdm_match warning for !CONFIG_OF
ASoC: ti: omap-mcbsp: Fix runtime PM underflow warnings
Add ALC295 to pin fall back table.
Remove 5 pin quirks for Dell ALC295.
ALC295 was only support MIC2 for external MIC function.
ALC295 assigned model "ALC269_FIXUP_DELL1_MIC_NO_PRESENCE" for pin
fall back table.
It was assigned wrong model. So, let's remove it.
Fixes: fbc571290d ("ALSA: hda/realtek - Fixed Headphone Mic can't record on Dell platform")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7c1998e873834df98d59bd7e0d08c72e@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Proposed patch fixes initialization of CSC3551 on the UM5302LA laptop.
Patching DSDT table is not required since ASUS did added _DSD entry.
Nothing new introduced but reused work started by Stefan B.
Currently there is no official firmware available for 10431A83 on
cirrus git unfortunately.
For testing used 104317f3 (which is also seems on i2c bus):
$ cd /lib/firmware/cirrus/ && \
for fw in $(find ./ -name '*104317f3*'); do newfw=$(echo $fw | sed 's/104317f3/10431a83/g'); echo echo "$fw -> $newfw"; ln -s $f $newfw; done
With the patch applied to 6.6.0 and obviously symlinks to 104317F3 FW,
speakers works and to my susrprise they sound quite good and loud
without distortion.
Probably confirmation from cirrus team is needed on firmware.
Signed-off-by: Vitalii Torshyn <vitaly.torshyn@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218119
Link: https://lore.kernel.org/r/CAHiQ-bCMPpCJ8eOYAaVVoqGkFixS1qTgSS4xfbZvL4oZV9LYew@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell new platform support dual speaker. But BIOS verb table only show one speaker.
It will fill verb table for second speaker. Then bind with CS AMP model.
Fixes: de90f5165b ("ALSA: hda/realtek: Add support for DELL Oasis 13/14/16 laptops")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/4dd390a77bf742b8a518ac2deee00b0f@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent AMD platforms expose an HD-audio bus but without any actual
codecs, which is internally tied with a USB-audio device, supposedly.
It results in "no codecs" error of HD-audio bus driver, and it's
nothing but a waste of resources.
snd_hda_intel 0000:59:00.6: no codecs found!
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Link: https://lore.kernel.org/r/20231105152834.5620-1-akoskovich@pm.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
there's little I can say which isn't in the individual changelogs.
The lengthier patch series are
- "kdump: use generic functions to simplify crashkernel reservation in
arch", from Baoquan He. This is mainly cleanups and consolidation of
the "crashkernel=" kernel parameter handling.
- After much discussion, David Laight's "minmax: Relax type checks in
min() and max()" is here. Hopefully reduces some typecasting and the
use of min_t() and max_t().
- A group of patches from Oleg Nesterov which clean up and slightly fix
our handling of reads from /proc/PID/task/... and which remove
task_struct.therad_group.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZUQP9wAKCRDdBJ7gKXxA
jmOAAQDh8sxagQYocoVsSm28ICqXFeaY9Co1jzBIDdNesAvYVwD/c2DHRqJHEiS4
63BNcG3+hM9nwGJHb5lyh5m79nBMRg0=
=On4u
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2023-11-02-14-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"As usual, lots of singleton and doubleton patches all over the tree
and there's little I can say which isn't in the individual changelogs.
The lengthier patch series are
- 'kdump: use generic functions to simplify crashkernel reservation
in arch', from Baoquan He. This is mainly cleanups and
consolidation of the 'crashkernel=' kernel parameter handling
- After much discussion, David Laight's 'minmax: Relax type checks in
min() and max()' is here. Hopefully reduces some typecasting and
the use of min_t() and max_t()
- A group of patches from Oleg Nesterov which clean up and slightly
fix our handling of reads from /proc/PID/task/... and which remove
task_struct.thread_group"
* tag 'mm-nonmm-stable-2023-11-02-14-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (64 commits)
scripts/gdb/vmalloc: disable on no-MMU
scripts/gdb: fix usage of MOD_TEXT not defined when CONFIG_MODULES=n
.mailmap: add address mapping for Tomeu Vizoso
mailmap: update email address for Claudiu Beznea
tools/testing/selftests/mm/run_vmtests.sh: lower the ptrace permissions
.mailmap: map Benjamin Poirier's address
scripts/gdb: add lx_current support for riscv
ocfs2: fix a spelling typo in comment
proc: test ProtectionKey in proc-empty-vm test
proc: fix proc-empty-vm test with vsyscall
fs/proc/base.c: remove unneeded semicolon
do_io_accounting: use sig->stats_lock
do_io_accounting: use __for_each_thread()
ocfs2: replace BUG_ON() at ocfs2_num_free_extents() with ocfs2_error()
ocfs2: fix a typo in a comment
scripts/show_delta: add __main__ judgement before main code
treewide: mark stuff as __ro_after_init
fs: ocfs2: check status values
proc: test /proc/${pid}/statm
compiler.h: move __is_constexpr() to compiler.h
...
Most of changes at this time are for ASoC, spread over ASoC core and
drivers due to the API prefix standardization. Other than that, there
have little change wrt API, rather lots of driver-specific updates and
fixes. Some highlight below:
ASoC:
- Standardization of API prefix
- GPIO API usage improvements
- Support for HDA patches
- Lots of work on SOF, including crash dump support
- Fixes for noise when stopping some Sounwire CODECs
- Support for AMD platforms with es83xx, AMD ACP 6.3 and 7.0, Awinc
AT87390 and AW88399, many Intel platforms, many Mediatek platforms,
Qualcomm SM6115 and SC7180 platforms, Richtek RTQ9128 and Texas
Instruments TAS575x
HD-audio and USB-audio:
- Deferred probe support of audio component binding
- More fixes and enhancements for Cirrus subcodecs
- USB Scarlett2 mixer and McIntosh DSD quirk
Others:
- More enhancement of snd-aloop driver
- Update MAINTAINERS entry for linux-sound mailing list
-----BEGIN PGP SIGNATURE-----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=2/dI
-----END PGP SIGNATURE-----
Merge tag 'sound-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Most of changes at this time are for ASoC, spread over ASoC core and
drivers due to the API prefix standardization.
Other than that, there have little change wrt API, rather lots of
driver-specific updates and fixes.
Some highlight below:
ASoC:
- Standardization of API prefix
- GPIO API usage improvements
- Support for HDA patches
- Lots of work on SOF, including crash dump support
- Fixes for noise when stopping some Sounwire CODECs
- Support for AMD platforms with es83xx, AMD ACP 6.3 and 7.0, Awinc
AT87390 and AW88399, many Intel platforms, many Mediatek platforms,
Qualcomm SM6115 and SC7180 platforms, Richtek RTQ9128 and Texas
Instruments TAS575x
HD-audio and USB-audio:
- Deferred probe support of audio component binding
- More fixes and enhancements for Cirrus subcodecs
- USB Scarlett2 mixer and McIntosh DSD quirk
Others:
- More enhancement of snd-aloop driver
- Update MAINTAINERS entry for linux-sound mailing list"
* tag 'sound-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (485 commits)
ALSA: hda: cs35l41: Fix missing error code in cs35l41_smart_amp()
ALSA: hda: cs35l41: mark cs35l41_verify_id() static
ASoC: codecs: wsa883x: make use of new mute_unmute_on_trigger flag
ASoC: soc-dai: add flag to mute and unmute stream during trigger
ASoC: ams-delta.c: use component after check
ASoC: amd: acp: select SND_SOC_AMD_ACP_LEGACY_COMMON for ACP63
ASoC: codecs: aw88399: fix typo in Kconfig select
ASoC: amd: acp: add ACPI dependency
ASoC: Intel: avs: Add rt5514 machine board
ASoC: Intel: avs: Add rt5514 machine board
ALSA: scarlett2: Add missing check with firmware version control
ALSA: virtio: use ack callback
ALSA: scarlett2: Remap Level Meter values
ALSA: scarlett2: Allow passing any output to line_out_remap()
ALSA: scarlett2: Add support for reading firmware version
ALSA: scarlett2: Rename Gen 3 config sets
ALSA: scarlett2: Rename scarlett_gen2 to scarlett2
ASoC: cs35l41: Detect CSPL errors when sending CSPL commands
ALSA: hda: cs35l41: Check CSPL state after loading firmware
ALSA: hda: cs35l41: Do not unload firmware before reset in system suspend
...
-----BEGIN PGP SIGNATURE-----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=G//C
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use acpi_evaluate_dsm_typed() instead of open-coding _DSM
evaluation to learn device characteristics (Andy Shevchenko)
- Tidy multi-function header checks using new PCI_HEADER_TYPE_MASK
definition (Ilpo Järvinen)
- Simplify config access error checking in various drivers (Ilpo
Järvinen)
- Use pcie_capability_clear_word() (not
pcie_capability_clear_and_set_word()) when only clearing (Ilpo
Järvinen)
- Add pci_get_base_class() to simplify finding devices using base
class only (ignoring subclass and programming interface) (Sui
Jingfeng)
- Add pci_is_vga(), which includes ancient PCI_CLASS_NOT_DEFINED_VGA
devices from before the Class Code was added to PCI (Sui Jingfeng)
- Use pci_is_vga() for vgaarb, sysfs "boot_vga", virtio, qxl to
include ancient VGA devices (Sui Jingfeng)
Resource management:
- Make pci_assign_unassigned_resources() non-init because sparc uses
it after init (Randy Dunlap)
Driver binding:
- Retain .remove() and .probe() callbacks (previously __init) because
sysfs may cause them to be called later (Uwe Kleine-König)
- Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device, so
it can be claimed by dwc3 instead (Vicki Pfau)
PCI device hotplug:
- Add Ampere Altra Attention Indicator extension driver for acpiphp
(D Scott Phillips)
Power management:
- Quirk VideoPropulsion Torrent QN16e with longer delay after reset
(Lukas Wunner)
- Prevent users from overriding drivers that say we shouldn't use
D3cold (Lukas Wunner)
- Avoid PME from D3hot/D3cold for AMD Rembrandt and Phoenix USB4
because wakeup interrupts from those states don't work if amd-pmc
has put the platform in a hardware sleep state (Mario Limonciello)
IOMMU:
- Disable ATS for Intel IPU E2000 devices with invalidation message
endianness erratum (Bartosz Pawlowski)
Error handling:
- Factor out interrupt enable/disable into helpers (Kai-Heng Feng)
Peer-to-peer DMA:
- Fix flexible-array usage in struct pci_p2pdma_pagemap in case we
ever use pagemaps with multiple entries (Gustavo A. R. Silva)
ASPM:
- Revert a change that broke when drivers disabled L1 and users later
enabled an L1.x substate via sysfs, and fix a similar issue when
users disabled L1 via sysfs (Heiner Kallweit)
Endpoint framework:
- Fix double free in __pci_epc_create() (Dan Carpenter)
- Use IS_ERR_OR_NULL() to simplify endpoint core (Ruan Jinjie)
Cadence PCIe controller driver:
- Drop unused "is_rc" member (Li Chen)
Freescale Layerscape PCIe controller driver:
- Enable 64-bit addressing in endpoint mode (Guanhua Gao)
Intel VMD host bridge driver:
- Fix multi-function header check (Ilpo Järvinen)
Microsoft Hyper-V host bridge driver:
- Annotate struct hv_dr_state with __counted_by (Kees Cook)
NVIDIA Tegra194 PCIe controller driver:
- Drop setting of LNKCAP_MLW (max link width) since dw_pcie_setup()
already does this via dw_pcie_link_set_max_link_width() (Yoshihiro
Shimoda)
Qualcomm PCIe controller driver:
- Use PCIE_SPEED2MBS_ENC() to simplify encoding of link speed
(Manivannan Sadhasivam)
- Add a .write_dbi2() callback so DBI2 register writes, e.g., for
setting the BAR size, work correctly (Manivannan Sadhasivam)
- Enable ASPM for platforms that use 1.9.0 ops, because the PCI core
doesn't enable ASPM states that haven't been enabled by the
firmware (Manivannan Sadhasivam)
Renesas R-Car Gen4 PCIe controller driver:
- Add DesignWare core support (set max link width, EDMA_UNROLL flag,
.pre_init(), .deinit(), etc) for use by R-Car Gen4 driver
(Yoshihiro Shimoda)
- Add driver and DT schema for DesignWare-based Renesas R-Car Gen4
controller in both host and endpoint mode (Yoshihiro Shimoda)
Xilinx NWL PCIe controller driver:
- Update ECAM size to support 256 buses (Thippeswamy Havalige)
- Stop setting bridge primary/secondary/subordinate bus numbers,
since PCI core does this (Thippeswamy Havalige)
Xilinx XDMA controller driver:
- Add driver and DT schema for Zynq UltraScale+ MPSoCs devices with
Xilinx XDMA Soft IP (Thippeswamy Havalige)
Miscellaneous:
- Use FIELD_GET()/FIELD_PREP() to simplify and reduce use of _SHIFT
macros (Ilpo Järvinen, Bjorn Helgaas)
- Remove logic_outb(), _outw(), outl() duplicate declarations (John
Sanpe)
- Replace unnecessary UTF-8 in Kconfig help text because menuconfig
doesn't render it correctly (Liu Song)"
* tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (102 commits)
PCI: qcom-ep: Add dedicated callback for writing to DBI2 registers
PCI: Simplify pcie_capability_clear_and_set_word() to ..._clear_word()
PCI: endpoint: Fix double free in __pci_epc_create()
PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx XDMA PCIe Root Port Bridge
PCI: xilinx-cpm: Move IRQ definitions to a common header
PCI: xilinx-nwl: Modify ECAM size to enable support for 256 buses
PCI: xilinx-nwl: Rename the NWL_ECAM_VALUE_DEFAULT macro
dt-bindings: PCI: xilinx-nwl: Modify ECAM size in the DT example
PCI: xilinx-nwl: Remove redundant code that sets Type 1 header fields
PCI: hotplug: Add Ampere Altra Attention Indicator extension driver
PCI/AER: Factor out interrupt toggling into helpers
PCI: acpiphp: Allow built-in drivers for Attention Indicators
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
...
