Currently, the device tree of ata port and scsi host looks as below,
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
This patch makes ata port as parent device of scsi host, then it becomes
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
With this change, the ata port runtime PM is easier.
For example, the ata port runtime suspend will happen as,
disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is another attempt at fixing the same problem that 270dac35c2
(libata: ahci_start_engine compliant to AHCI spec) tried to solve.
Unfortunately, 270dac35c2 created regressions for a lot more common
controllers and got reverted.
This specific AHCI IP block becomes a brick if the DMA engine is
started while DRQ is set. It is not possible to avoid the condition
completely but the most common occurrence is caused by spurious use of
ahci_start_engine() from ahci_start_port() during init sequence.
DMA engine is started after both soft and hard resets and
ahci_start_port() is always followed by resets, so there is no reason
to start DMA engine from ahci_start_port().
This patch removes ahci_start_engine() invocation from
ahci_start_port(). This change makes failure path of
ahci_port_suspend() leave engine stopped without following resets.
This is resolved by replacing ahci_start_port() call with
ata_port_freeze() which forces resets afterwards, which is the better
behavior anyway.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Jian Peng <jipeng2005@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fix CAN MAINTAINERS SCM tree type
mwifiex: fix crash during simultaneous scan and connect
b43: fix regression in PIO case
ath9k: Fix kernel panic in AR2427 in AP mode
CAN MAINTAINERS update
net: fsl: fec: fix build for mx23-only kernel
sch_qfq: fix overflow in qfq_update_start()
Revert "Bluetooth: Increase HCI reset timeout in hci_dev_do_close"
This reverts commit 93b2ec0128.
The call to "schedule_work()" in rtc_initialize_alarm() happens too
early, and can cause oopses at bootup
Neil Brown explains why we do it:
"If you set an alarm in the future, then shutdown and boot again after
that time, then you will end up with a timer_queue node which is in
the past.
When this happens the queue gets stuck. That entry-in-the-past won't
get removed until and interrupt happens and an interrupt won't happen
because the RTC only triggers an interrupt when the alarm is "now".
So you'll find that e.g. "hwclock" will always tell you that
'select' timed out.
So we force the interrupt work to happen at the start just in case."
and has a patch that convert it to do things in-process rather than with
the worker thread, but right now it's too late to play around with this,
so we just revert the patch that caused problems for now.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Requested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Requested-by: John Stultz <john.stultz@linaro.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit c0afabd3d5.
It causes failures on Toshiba laptops - instead of disabling the alarm,
it actually seems to enable it on the affected laptops, resulting in
(for example) the laptop powering on automatically five minutes after
shutdown.
There's a patch for it that appears to work for at least some people,
but it's too late to play around with this, so revert for now and try
again in the next merge window.
See for example
http://bugs.debian.org/652869
Reported-and-bisected-by: Andreas Friedrich <afrie@gmx.net> (Toshiba Tecra)
Reported-by: Antonio-M. Corbi Bellot <antonio.corbi@ua.es> (Toshiba Portege R500)
Reported-by: Marco Santos <marco.santos@waynext.com> (Toshiba Portege Z830)
Reported-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr> (Toshiba Portege R830)
Cc: Jonathan Nieder <jrnieder@gmail.com>
Requested-by: John Stultz <john.stultz@linaro.org>
Cc: stable@kernel.org # for the versions that applied this
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If 'iw connect' command is fired when driver is already busy in
serving 'iw scan' command, ssid specific scan operation for connect
is skipped. In this case cmd wait queue handler gets called with no
command in queue (i.e. adapter->cmd_queued = NULL).
This patch adds a NULL check in mwifiex_wait_queue_complete()
routine to fix crash observed during simultaneous scan and assoc
operations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the regression, introduced by
commit 17030f48e3
From: Rafał Miłecki <zajec5@gmail.com>
Date: Thu, 11 Aug 2011 17:16:27 +0200
Subject: [PATCH] b43: support new RX header, noticed to be used in 598.314+ fw
in PIO case.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If one only selects mx23-based boards, compile fails:
drivers/net/ethernet/freescale/fec.c:410:2: error: 'FEC_HASH_TABLE_HIGH' undeclared (first use in this function)
drivers/net/ethernet/freescale/fec.c:411:2: error: 'FEC_HASH_TABLE_LOW' undeclared (first use in this function)
This is because fec.h uses CONFIG_SOC_IMX28 to determine the register
layout of the core which makes sense since the MX23 does not have a fec.
However, Kconfig uses the broader ARCH_MXS symbol and this way even
makes the fec-driver default for MX23. Adapt Kconfig to use the more
precise SOC_IMX28 as well.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: ctnetlink: fix timeout calculation
ipvs: try also real server with port 0 in backup server
skge: restore rx multicast filter on resume and after config changes
mlx4_en: nullify cq->vector field when closing completion queue
The current gspca core code has a regression where it no longer properly
falls back to lower alt settings when there is not enough bandwidth.
This causes many iso based usb-1 cameras to not work when plugged into a
usb2 hub or a sandybridge chipset motherboard!
This patch fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restore skge hardware registers for multicast filtering to their
appropriate values after system resume and after hardware restarts
that are done when changing certain settings.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caused loss of connectivity when changing ring size.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO_wdt.c - problems with newer hardware due to SMI clearing (part 2)
watchdog: hpwdt: Changes to handle NX secure bit in 32bit path
watchdog: sp805: Fix section mismatch in ID table.
watchdog: move coh901327 state holders
The new iso bandwidth calculation code accidentally has broken support
for bulk mode cameras. This has broken the following drivers:
finepix, jeilinj, ovfx2, ov534, ov534_9, se401, sq905, sq905c, sq930x,
stv0680, vicam.
Thix patch fixes this. Fix tested with: se401, sq905, sq905c, stv0680 & vicam
cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixing wrong register offset which is used to retrieve the number of buttons
attached to the hardware.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Redhat Bugzilla: Bug 727875 - TCO_EN bit is disabled by TCO driver
The previous patch breaks reset watchdog behaviour on the older hardware.
It is therefor better to make sure that the behaviour for older hardware (<=ICH5 or
6300ESB) is preserved and that the behaviour for newer hardware is changed.
We therefor use the iTCO_version to see if we need the clearing of the SMI_TCO_EN
bit in the SMI_EN register.
So the new behaviour becomes:
turn_SMI_watchdog_clear_off=0 -> Do not turn off SMI clearing watchdog.
turn_SMI_watchdog_clear_off=1 -> Turn off SMI clearing watchdog when iTCO_version=1
(ICHO till ICH5 + 6300ESB only)
turn_SMI_watchdog_clear_off=2 -> Turn off SMI clearing watchdog.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
RC6 fails again.
> I found my system freeze mostly during starting up X and KDE. Sometimes it
> works for some minutes, sometimes it freezes immediatly. When the freeze
> happens, everything is dead (even the reset button does not work, I need to
> power cycle).
> I disabled RC6, and my system runs wonderfully.
> The system is a Z68 Pro board with Sandybridge i5-2500K processor, 8
> GB of RAM and UEFI firmware.
Reported-by: Kai Krakow <hurikhan77@gmail.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Semaphores still cause problems on some machines:
> From Udo Steinberg:
>
> With Linux-3.2-rc6 I'm frequently seeing GPU hangs when large amounts of
> text scroll in an xterm, such as when extracting a tar archive. Such as this
> one (note the timestamps):
>
> I can reproduce it fairly easily with something
> as simple as:
>
> while true; do dmesg; done
This patch turns them off on SNB while leaving them on for IVB.
Reported-by: Udo Steinberg <udo@hypervisor.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Eugeni Dodonov <eugeni@dodonov.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes use of the set_memory_x() kernel API in order
to make necessary BIOS calls to source NMIs.
This is needed for SLES11 SP2 and the latest upstream kernel as it appears
the NX Execute Disable has grown in its control.
Signed-off by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable@kernel.org
The AMBA ID table is marked as __initdata, yet it is referenced by the
driver struct which is not. This causes a (somewhat unhelpful) section
mismatch warning:
WARNING: drivers/watchdog/sp805_wdt.o(.data+0x4c): Section mismatch in
reference from the variable sp805_wdt_driver to the (unknown
reference) .init.data:(unknown)
Fix this by removing the annotation.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The state holders used in the PM path of the drivers report as
unused variables when compiling without CONFIG_PM so let's
move them inside CONFIG_PM.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
vmwgfx: fix incorrect VRAM size check in vmw_kms_fb_create()
drm/radeon/kms: bail on BTC parts if MC ucode is missing
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
Make sure that mutex is released upon register writing failure.
This fixes boot freezing observed on ARM based OLPC
(http://dev.laptop.org/ticket/11357).
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://neil.brown.name/md:
md/bitmap: It is OK to clear bits during recovery.
md: don't give up looking for spares on first failure-to-add
md/raid5: ensure correct assessment of drives during degraded reshape.
md/linear: fix hot-add of devices to linear arrays.
commit d0a4bb4927 introduced a
regression which is annoying but fairly harmless.
When writing to an array that is undergoing recovery (a spare
in being integrated into the array), writing to the array will
set bits in the bitmap, but they will not be cleared when the
write completes.
For bits covering areas that have not been recovered yet this is not a
problem as the recovery will clear the bits. However bits set in
already-recovered region will stay set and never be cleared.
This doesn't risk data integrity. The only negatives are:
- next time there is a crash, more resyncing than necessary will
be done.
- the bitmap doesn't look clean, which is confusing.
While an array is recovering we don't want to update the
'events_cleared' setting in the bitmap but we do still want to clear
bits that have very recently been set - providing they were written to
the recovering device.
So split those two needs - which previously both depended on 'success'
and always clear the bit of the write went to all devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Before performing a recovery we try to remove any spares that
might not be working, then add any that might have become relevant.
Currently we abort on the first spare that cannot be added.
This is a false optimisation.
It is conceivable that - depending on rules in the personality - a
subsequent spare might be accepted.
Also the loop does other things like count the available spares and
reset the 'recovery_offset' value.
If we abort early these might not happen properly.
So remove the early abort.
In particular if you have an array what is undergoing recovery and
which has extra spares, then the recovery may not restart after as
reboot as the could of 'spares' might end up as zero.
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NeilBrown <neilb@suse.de>
While reshaping a degraded array (as when reshaping a RAID0 by first
converting it to a degraded RAID4) we currently get confused about
which devices are in_sync. In most cases we get it right, but in the
region that is being reshaped we need to treat non-failed devices as
in-sync when we have the data but haven't actually written it out yet.
Reported-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit d70ed2e4fa
broke hot-add to a linear array.
After that commit, metadata if not written to devices until they
have been fully integrated into the array as determined by
saved_raid_disk. That patch arranged to clear that field after
a recovery completed.
However for linear arrays, there is no recovery - the integration is
instantaneous. So we need to explicitly clear the saved_raid_disk
field.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Fix usb/isp1760 build on sparc
usb: gadget: epautoconf: do not change number of streams
usb: dwc3: core: fix cached revision on our structure
usb: musb: fix reset issue with full speed device
Commit e133e737 didn't correctly fix the integer overflow issue.
- unsigned int required_size;
+ u64 required_size;
...
required_size = mode_cmd->pitch * mode_cmd->height;
- if (unlikely(required_size > dev_priv->vram_size)) {
+ if (unlikely(required_size > (u64) dev_priv->vram_size)) {
Note that both pitch and height are u32. Their product is still u32 and
would overflow before being assigned to required_size. A correct way is
to convert pitch and height to u64 before the multiplication.
required_size = (u64)mode_cmd->pitch * (u64)mode_cmd->height;
This patch calls the existing vmw_kms_validate_mode_vram() for
validation.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Reviewed-and-tested-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We already do this for cayman, need to also do it for
BTC parts. The default memory and voltage setup is not
adequate for advanced operation. Continuing will
result in an unusable display.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Add a flow_cache_flush_deferred function
ipv4: reintroduce route cache garbage collector
net: have ipconfig not wait if no dev is available
sctp: Do not account for sizeof(struct sk_buff) in estimated rwnd
asix: new device id
davinci-cpdma: fix locking issue in cpdma_chan_stop
sctp: fix incorrect overflow check on autoclose
r8169: fix Config2 MSIEnable bit setting.
llc: llc_cmsg_rcv was getting called after sk_eat_skb.
net: bpf_jit: fix an off-one bug in x86_64 cond jump target
iwlwifi: update SCD BC table for all SCD queues
Revert "Bluetooth: Revert: Fix L2CAP connection establishment"
Bluetooth: Clear RFCOMM session timer when disconnecting last channel
Bluetooth: Prevent uninitialized data access in L2CAP configuration
iwlwifi: allow to switch to HT40 if not associated
iwlwifi: tx_sync only on PAN context
mwifiex: avoid double list_del in command cancel path
ath9k: fix max phy rate at rate control init
nfc: signedness bug in __nci_request()
iwlwifi: do not set the sequence control bit is not needed
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Include linux/io.h to jz4740-adc
mfd: Use request_threaded_irq for twl4030-irq instead of irq_set_chained_handler
mfd: Base interrupt for twl4030-irq must be one-shot
mfd: Handle tps65910 clear-mask correctly
mfd: add #ifdef CONFIG_DEBUG_FS guard for ab8500_debug_resources
mfd: Fix twl-core oops while calling twl_i2c_* for unbound driver
mfd: include linux/module.h for ab5500-debugfs
mfd: Update wm8994 active device checks for WM1811
mfd: Set tps6586x bits if new value is different from the old one
mfd: Set da903x bits if new value is different from the old one
mfd: Set adp5520 bits if new value is different from the old one
mfd: Add missed free_irq in da903x_remove
* 'for-greg' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: gadget: epautoconf: do not change number of streams
usb: dwc3: core: fix cached revision on our structure
usb: musb: fix reset issue with full speed device
This commit:
commit 8f5d621543
Author: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Date: Mon Oct 10 18:06:54 2011 +0200
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
To be able to use the driver on other OF-aware architectures, too.
And add necessary OF related #includes to fix compilation error.
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
enabled the build on all CONFIG_OF architectures, but it cannot do
this.
This driver depends upon CONFIG_OF_IRQ but not all CONFIG_OF platforms
support that infrastructure, in particular Sparc does not so the
build fails.
Please push a patch like the following to Linus so that this code only
gets built where it actually should.
--------------------
usb/isp1760: Add missing CONFIG_OF_IRQ dependency on OF code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/mtd-2.6:
mtd: plat_ram: call mtd_device_register only if partition data exists
mtd: pxa2xx-flash.c: It used to fall back to provided table.
mtd: gpmi: add missing include 'module.h'
mtd: ndfc: fix typo in structure dereference
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time/clocksource: Fix kernel-doc warnings
rtc: m41t80: Workaround broken alarm functionality
rtc: Expire alarms after the time is set.
