Pull input fixes from Dmitry Torokhov:
"A few small updates to drivers.
Of note we are now deferring probes of i8042 on some Asus devices as
the controller is not ready to respond to queries first time around
when the driver is compiled into the kernel"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
Input: atmel_mxt_ts - fix double free in mxt_read_info_block
Input: goodix - fix memory leak in goodix_firmware_upload
Input: goodix - add id->model mapping for the "9111" model
Input: goodix - try not to touch the reset-pin on x86/ACPI devices
Input: i8042 - enable deferred probe quirk for ASUS UM325UA
Input: elantech - fix stack out of bound access in elantech_change_report_id()
Input: iqs626a - prohibit inlining of channel parsing functions
Input: i8042 - add deferred probe support
The eKTH3900/eKTH5312 series do not support the firmware update rules of
Remark ID. Exclude these two series from checking it when updating the
firmware in touch controllers.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Link: https://lore.kernel.org/r/1639619603-20616-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The "id_buf" buffer is stored in "data->raw_info_block" and freed by
"mxt_free_object_table" in case of error.
Return instead of jumping to avoid a double free.
Addresses-Coverity-ID: 1474582 ("Double free")
Fixes: 068bdb67ef ("Input: atmel_mxt_ts - fix the firmware update")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20211212194257.68879-1-jose.exposito89@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeeca9 ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ASUS UM325UA suffers from the same issue as the ASUS UX425UA, which
is a very similar laptop. The i8042 device is not usable immediately
after boot and fails to initialize, requiring a deferred retry.
Enable the deferred probe quirk for the UM325UA.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211204015615.232948-1-samuel@cavoj.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some automated builds report a stack frame size in excess of 2 kB for
iqs626_probe(); the culprit appears to be the call to iqs626_parse_prop().
To solve this problem, specify noinline_for_stack for all of the
iqs626_parse_*() helper functions which are called inside a for loop
within iqs626_parse_prop().
As a result, a build with '-Wframe-larger-than' as low as 512 is free of
any such warnings.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20211129004104.453930-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA. It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready. Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module. However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.
This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above. When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.
The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry. As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.
The deferred probe part is based on Fabio's initial work.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When booting the xenbus driver will wait for PV devices to have
connected to their backends before continuing. The timeout is different
between essential and non-essential devices.
Non-essential devices are identified by their nodenames directly in the
xenbus driver, which requires to update this list in case a new device
type being non-essential is added (this was missed for several types
in the past).
In order to avoid this problem, add a "not_essential" flag to struct
xenbus_driver which can be set to "true" by the respective frontend.
Set this flag for the frontends currently regarded to be not essential
(vkbs and vfb) and use it for testing in the xenbus driver.
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211022064800.14978-2-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Pull input updates from Dmitry Torokhov:
"Just one new driver (Cypress StreetFighter touchkey), and no input
core changes this time.
Plus various fixes and enhancements to existing drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: iforce - fix control-message timeout
Input: wacom_i2c - use macros for the bit masks
Input: ili210x - reduce sample period to 15ms
Input: ili210x - improve polled sample spacing
Input: ili210x - special case ili251x sample read out
Input: elantench - fix misreporting trackpoint coordinates
Input: synaptics-rmi4 - Fix device hierarchy
Input: i8042 - Add quirk for Fujitsu Lifebook T725
Input: cap11xx - add support for cap1206
Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
Input: ili210x - add ili251x firmware update support
Input: ili210x - export ili251x version details via sysfs
Input: ili210x - use resolution from ili251x firmware
Input: pm8941-pwrkey - respect reboot_mode for warm reset
reboot: export symbol 'reboot_mode'
Input: max77693-haptic - drop unneeded MODULE_ALIAS
Input: cpcap-pwrbutton - do not set input parent explicitly
Input: max8925_onkey - don't mark comment as kernel-doc
Input: ads7846 - do not attempt IRQ workaround when deferring probe
Input: ads7846 - use input_set_capability()
...
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 4873586278 ("Input: iforce - use DMA-safe buffer when getting IDs from USB")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 5.3
Link: https://lore.kernel.org/r/20211025115501.5190-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.
The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.
Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.
According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.
Signed-off-by: Phoenix Huang <phoenix@emc.com.tw>
Tested-by: Yufei Du <yufeidu@cs.unc.edu>
Link: https://lore.kernel.org/r/20210729010940.5752-1-phoenix@emc.com.tw
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The created rmi device is orphan, which breaks the real device
hierarchy, and can cause some trouble, especially during suspend
and resume sequences. E.g. in case of I2C, rmi dev should be child
of the I2C client device.
Fix this, assigning the transport device as parent of the rmi device.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1635514971-18415-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fujitsu Lifebook T725 laptop requires, like a few other similar
models, the nomux and notimeout options to probe the touchpad
properly. This patch adds the corresponding quirk entries.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1191980
Tested-by: Neal Gompa <ngompa13@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211103070019.13374-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull HID updates from Jiri Kosina:
- support for Nintendo Switch Pro Controllers and Joy-Cons (Daniel J.
Ogorchock)
- support for new revision of the NitroKey U2F device firmware (Andrej
Shadura)
- LED handling improvements for Sony Playstation5 controllers (Roderick
Colenbrander)
- support for Apple 2021 Magic Keyboard (Alex Henrie)
- other assorted code cleanups and new device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (41 commits)
HID: nintendo: fix -Werror build
HID: playstation: require multicolor LED functionality
HID: u2fzero: properly handle timeouts in usb_submit_urb
HID: u2fzero: clarify error check and length calculations
HID: u2fzero: Support NitroKey U2F revision of the device
HID: wacom: Make use of the helper function devm_add_action_or_reset()
HID: wacom: Shrink critical section in `wacom_add_shared_data`
HID: nintendo: prevent needless queueing of the rumble worker
HID: nintendo: ratelimit subcommands and rumble
HID: nintendo: improve rumble performance and stability
HID: nintendo: add IMU support
HID: nintendo: add support for reading user calibration
HID: nintendo: add support for charging grip
HID: nintendo: set controller uniq to MAC
HID: nintendo: reduce device removal subcommand errors
HID: nintendo: patch hw version for userspace HID mappings
HID: nintendo: send subcommands after receiving input report
HID: nintendo: improve subcommand reliability
HID: nintendo: add rumble support
HID: nintendo: add home led support
...
Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPczQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykWbwCfaIScbUoCUx+h/uP93nKKD8B3KgYAoMvFuhhD
D/fTLggs12x5NsvLBgtZ
=rq0R
-----END PGP SIGNATURE-----
Merge tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (86 commits)
tty: Fix extra "not" in TTY_DRIVER_REAL_RAW description
serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE
tty: rpmsg: Define tty name via constant string literal
tty: rpmsg: Add pr_fmt() to prefix messages
tty: rpmsg: Use dev_err_probe() in ->probe()
tty: rpmsg: Unify variable used to keep an error code
tty: rpmsg: Assign returned id to a local variable
serial: stm32: push DMA RX data before suspending
serial: stm32: terminate / restart DMA transfer at suspend / resume
serial: stm32: rework RX dma initialization and release
serial: 8250_pci: Remove empty stub pci_quatech_exit()
serial: 8250_pci: Replace custom pci_match_id() implementation
serial: xilinx_uartps: Fix race condition causing stuck TX
serial: sunzilog: Mark sunzilog_putchar() __maybe_unused
Revert "tty: hvc: pass DMA capable memory to put_chars()"
Revert "virtio-console: remove unnecessary kmemdup()"
serial: 8250_pci: Replace dev_*() by pci_*() macros
serial: 8250_pci: Get rid of redundant 'else' keyword
serial: 8250_pci: Refactor the loop in pci_ite887x_init()
tty: add rpmsg driver
...
Highlights:
- AMD-PMC S0ix support fixes and improvements
- HP-WMI support for Omen laptops
- New nvidia-wmi-ec-backlight driver
- New Intel ISH ECLITE driver
- WMI core cleanups
- Support for various new Melanox platforms
- System76 Laptop support improvements
- Surface Laptop Studio support and initial Surface Pro 8 support
- Various other small fixes and hardware-id additions
The following is an automated git shortlog grouped by driver:
ABI:
- sysfs-platform-intel-pmc: add blank lines to make it valid for ReST
- sysfs-platform-dell-privacy-wmi: correct ABI entries
ASoC:
- Intel: Move soc_intel_is_foo() helpers to a generic header
Add Intel ishtp eclite driver:
- Add Intel ishtp eclite driver
Add driver for ACPI WMAA EC-based backlight control:
- Add driver for ACPI WMAA EC-based backlight control
Documentation/ABI:
- Add new line card attributes for mlxreg-io sysfs interfaces
- Add new attributes for mlxreg-io sysfs interfaces
HID:
- surface-hid: Allow driver matching for target ID 1 devices
- surface-hid: Use correct event registry for managing HID events
Input:
- axp20x-pek - Use new soc_intel_is_cht() helper
Remove "WMAA" from identifier names in wmaa-backlight-wmi.c:
- Remove "WMAA" from identifier names in wmaa-backlight-wmi.c
Rename wmaa-backlight-wmi to nvidia-wmi-ec-backlight:
- Rename wmaa-backlight-wmi to nvidia-wmi-ec-backlight
Support for EC-connected GPIOs for identify LED/button on Barco P50 board:
- Support for EC-connected GPIOs for identify LED/button on Barco P50 board
acer-wmi:
- use __packed instead of __attribute__((packed))
amd-pmc:
- Drop check for valid alarm time
- Downgrade dev_info message to dev_dbg
- fix compilation without CONFIG_RTC_SYSTOHC_DEVICE
- Add special handling for timer based S0i3 wakeup
- adjust arguments for `amd_pmc_send_cmd`
- Add alternative acpi id for PMC controller
- Add a message to print resume time info
- Send command to dump data after clearing OS_HINT
- Fix compilation when CONFIG_DEBUGFS is disabled
- Export Idlemask values based on the APU
- Check s0i3 cycle status
- Increase the response register timeout
asus-wmi:
- rename platform_profile_* function symbols
barco-p50-gpio:
- use KEY_VENDOR for button instead of KEY_RESTART
dell:
- Make DELL_WMI_PRIVACY depend on DELL_WMI
- fix DELL_WMI_PRIVACY dependencies & build error
dell-wmi:
- Recognise or support new switches
docs:
- ABI: fix documentation warning in sysfs-driver-mlxreg-io
gigabyte-wmi:
- add support for B550 AORUS ELITE AX V2
- add support for B550I Aorus Pro AX
hp-wmi:
- rename platform_profile_* function symbols
- add support for omen laptops
ideapad-laptop:
- Add platform support for Ideapad 5 Pro 16ACH6-82L5
int1092:
- Fix non sequential device mode handling
intel_int0002_vgpio:
- Use the new soc_intel_is_byt()/_cht() helpers
intel_scu_ipc:
- Update timeout value in comment
- Increase virtual timeout to 10s
- Fix busy loop expiry time
intel_skl_int3472:
- Correct null check
lg-laptop:
- replace snprintf in show functions with sysfs_emit
- Correctly handle dmi_get_system_info() returning NULL
mlx-platform:
- Add support for new system SGN2410
- Add BIOS attributes for CoffeeLake COMEx based systems
- Extend FAN and LED configuration to support new MQM97xx systems
- Add support for multiply cooling devices
- Configure notifier callbacks for modular system
- Add initial support for new modular system
panasonic-laptop:
- Replace snprintf in show functions with sysfs_emit
platform:
- x86: ideapad-laptop: Use ACPI_COMPANION() directly
- lg-laptop: drop unneeded MODULE_ALIAS
platform/mellanox:
- mlxreg-lc: Add initial support for Nvidia line card devices
- mlxreg-io: Extend number of hwmon attributes
- mlxreg-hotplug: Extend logic for hotplug devices operations
- mlxreg-io: Fix read access of n-bytes size attributes
- mlxreg-io: Fix argument base in kstrtou32() call
platform/surface:
- aggregator_registry: Add initial support for Surface Pro 8
- aggregator_registry: Add support for Surface Laptop Studio
- gpe: Add support for Surface Laptop Studio
platform/x86/intel:
- hid: Add DMI switches allow list
- punit_ipc: Drop wrong use of ACPI_PTR()
platform_data/mlxreg:
- Add new field for secured access
- Add new type to support modular systems
sony-laptop:
- replace snprintf in show functions with sysfs_emit
surface:
- surface3_power: Drop redundant acpi_bus_get_device() call
- surface3-wmi: Use ACPI_COMPANION() directly
system76_acpi:
- Fix input device error handling
- fix Kconfig dependencies
- Add attribute group for kb_led_color
- Add battery charging thresholds
- Replace Fn+F2 function for OLED models
- Report temperature and fan speed
thinkpad_acpi:
- Fix bitwise vs. logical warning
- Fix coccinelle warnings
- Switch to common use of attributes
touchscreen_dmi:
- Add info for the Viglen Connect 10 tablet
- Update info for the Chuwi Hi10 Plus (CWI527) tablet
- Add info for the Chuwi HiBook (CWI514) tablet
update email addresses. Change all email addresses for Mark Gross to use markgross@kernel.org.:
- update email addresses. Change all email addresses for Mark Gross to use markgross@kernel.org.
wmi:
- change notification handler type
- more detailed error reporting in find_guid()
- introduce helper to retrieve event data
- introduce helper to determine type
- introduce helper to generate method names
- introduce helper to convert driver to WMI driver
- simplify error handling logic
- do not fail if disabling fails
- improve debug messages
- align arguments of functions
- move variables
- remove variable
- use sizeof(*p) in allocation
- use !p to check for NULL
- use sysfs_emit()
- make GUID block packed
- use guid_t and guid_equal()
- use bool instead of int
- use BIT() macro
- remove unnecessary checks
- remove stray empty line
- remove unnecessary casts
- remove unnecessary argument
- remove unnecessary variable
- remove unnecessary initializations
- remove unnecessary initialization
- remove commas
- fix checkpatch warnings
- fix kernel doc
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmGBVW0UHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9xufQgAnheynzaOChdXasbvR//mv+lyGE49
76uRA9HF9SeP430B+MTkZuYhEIiiY7lKjHi7ZY15HPY0r6wrrbJn+zDBpXFo3Scy
6CC/KUNNkwZgy1KoDC0v1SynlkHZgS4F98S1/IKkcBDQH91N0VltLFKuYYiPw2Hp
APMmQUxGGxdmBlxyKOZnFK5BicNCzGL9klkU2evQmywICx3ZT3Q9jQ1YIoiw85O+
sH7Owt3jIpWVbhb6TcPupuKw4LP6hqa8z9yYLchGaJQFyr1RXTznmLAB7foKRCJ/
48jGgjlHF2OkrLiOvT8hFMqpU52VjVUr0fBGyRjWb7dIpt5Fp1M2HLlRXA==
=cpVa
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- AMD-PMC S0ix support fixes and improvements
- HP-WMI support for Omen laptops
- New nvidia-wmi-ec-backlight driver
- New Intel ISH ECLITE driver
- WMI core cleanups
- Support for various new Melanox platforms
- System76 Laptop support improvements
- Surface Laptop Studio support and initial Surface Pro 8 support
- Various other small fixes and hardware-id additions"
* tag 'platform-drivers-x86-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (106 commits)
platform/x86: system76_acpi: Fix input device error handling
platform/x86: touchscreen_dmi: Add info for the Viglen Connect 10 tablet
platform/surface: aggregator_registry: Add initial support for Surface Pro 8
platform/x86: mlx-platform: Add support for new system SGN2410
platform/x86: mlx-platform: Add BIOS attributes for CoffeeLake COMEx based systems
platform/x86: mlx-platform: Extend FAN and LED configuration to support new MQM97xx systems
platform/x86: asus-wmi: rename platform_profile_* function symbols
platform/x86: hp-wmi: rename platform_profile_* function symbols
platform/x86: amd-pmc: Drop check for valid alarm time
platform/x86: amd-pmc: Downgrade dev_info message to dev_dbg
platform/x86: amd-pmc: fix compilation without CONFIG_RTC_SYSTOHC_DEVICE
platform/x86: system76_acpi: fix Kconfig dependencies
platform/x86: barco-p50-gpio: use KEY_VENDOR for button instead of KEY_RESTART
platform/x86: sony-laptop: replace snprintf in show functions with sysfs_emit
platform/x86: lg-laptop: replace snprintf in show functions with sysfs_emit
docs: ABI: fix documentation warning in sysfs-driver-mlxreg-io
platform/x86: wmi: change notification handler type
HID: surface-hid: Allow driver matching for target ID 1 devices
HID: surface-hid: Use correct event registry for managing HID events
platform/surface: aggregator_registry: Add support for Surface Laptop Studio
...
According to the datasheet "The CAP1206 is pin- and register-compatible
with the CAP1106, with the exception of the GAIN[1:0] bits and ALT_POL
bit"(57). So, this patch aims to disable them as they are no longer
used.
Signed-off-by: Jesse Taube <mr.bossman075@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for the controller's IMU. The accelerometer and
gyro data are both provided to userspace using a second input device.
The devices can be associated using their uniq value (set to the
controller's MAC address).
A large part of this patch's functionality was provided by Carl Mueller.
The IMU device is blacklisted from the joydev input handler.
Signed-off-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the new soc_intel_is_cht() helper to find out if we are running
on a CHT device rather then checking the ACPI _HRV field.
This is more reliable (some CHT devices have been found where the _HRV
for the PMIC is 2 rather then 3) and leads to a nice cleanup.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211018143324.296961-4-hdegoede@redhat.com
Pull input fixes from Dmitry Torokhov:
- a new product ID for the xpad joystick driver
- fixes to resistive-adc-touch and snvs_pwrkey drivers
- a change to touchscreen helpers to make clang happier
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: touchscreen - avoid bitwise vs logical OR warning
Input: xpad - add support for another USB ID of Nacon GC-100
Input: resistive-adc-touch - fix division by zero error on z1 == 0
Input: snvs_pwrkey - add clk handling
The ili251x firmware can be updated, this is used when switching between
different modes of operation of the touch surface, e.g. glove operation.
This patch implements the firmware update mechanism triggered by a write
into an sysfs attribute.
The firmware itself is distributed as an intel hex file with non-standard
types. The first two lines are of type 0xad, which indicates the start of
DataFlash payload, that is always at address 0xf000 on the ili251x, so it
can be dropped, and 0xac which indicates the position of firmware info in
the Application payload, that is always at address 0x2020 on the ili251x
and we do not care. The rest of the firmware is data of type 0x00, and we
care about that. To convert the firmware hex file into something usable
by the kernel, remove the first two lines and then use ihex2fw:
$ tail -n +3 input.hex > temp.hex
$ ./tools/firmware/ihex2fw temp.hex firmware/ilitek/ili251x.bin
To trigger the firmware update, place firmware file ilitek/ili251x.bin
into /lib/firmware/, write into firmware_update sysfs attribute and wait
about 30-40 seconds. The firmware update is slow. Afterward, verify the
firmware_version and mode sysfs attributes to check whether the firmware
got updated and the controller switched back to application (AP) mode by
reading out 'mode' attribute in sysfs.
Note that the content of firmware_version, e.g. 0600.0005.abcd.aa04 can
be matched to the content of the firmware hex file. The first four bytes,
0x06 0x00 0x00 0x05 can be found at ^:102030 00 05000006, the next four
bytes 0xab 0xcd 0xaa 0x04 at ^:10F000 00 nnnnnnnn ABCDAA04.
Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-3-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x firmware protocol permits readout of firmware version,
protocol version, mcu version and current mode (application, boot
loader, forced update). These information are useful when updating
the firmware on the il251x, e.g. to avoid updating the same firmware
into the device multiple times. The locking is now necessary to avoid
races between interrupt handler and the sysfs readouts.
Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-2-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ili251x firmware protocol permits readout of panel resolution,
implement this, but make it possible to override this value using
DT bindings. This way, older DTs which contain touchscreen-size-x
and touchscreen-size-y properties will behave just like before and
new DTs may avoid specifying these for ILI251x.
Note that the command format is different on other controllers, so
this functionality is isolated to ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some devices, e.g. Sony Xperia M4 Aqua, warm reset is used to reboot
device into bootloader and recovery mode. Instead of always doing hard
reset, add a check on reboot_mode for possible warm reset.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20210714095850.27185-3-shawn.guo@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210916170514.137977-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using devm_input_allocate_device() that already sets parent
of the input device, there is no need to do that again.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/YWpiZqrfC9+GQsM4@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Nacon GX100XF is already mapped, but it seems there is a Nacon
GC-100 (identified as NC5136Wht PCGC-100WHITE though I believe other
colours exist) with a different USB ID when in XInput mode.
Signed-off-by: Michael Cullen <michael@michaelcullen.name>
Link: https://lore.kernel.org/r/20211015192051.5196-1-michael@michaelcullen.name
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For proper pressure calculation we need at least x and z1 to be non
zero. Even worse, in case z1 we may run in to division by zero
error.
Fixes: 60b7db914d ("Input: resistive-adc-touch - rework mapping of channels")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20211007095727.29579-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On i.MX7S and i.MX8M* (but not i.MX6*) the pwrkey device has an
associated clock. Accessing the registers requires that this clock is
enabled. Binding the driver on at least i.MX7S and i.MX8MP while not
having the clock enabled results in a complete hang of the machine.
(This usually only happens if snvs_pwrkey is built as a module and the
rtc-snvs driver isn't already bound because at bootup the required clk
is on and only gets disabled when the clk framework disables unused clks
late during boot.)
This completes the fix in commit 135be16d35 ("ARM: dts: imx7s: add
snvs clock to pwrkey").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211013062848.2667192-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change the comment to a normal (non-kernel-doc) comment to avoid
these kernel-doc warnings:
max8925_onkey.c:2: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* MAX8925 ONKEY driver
max8925_onkey.c:2: warning: missing initial short description on line:
* MAX8925 ONKEY driver
Fixes: 3734574cac ("Input: enable onkey driver of max8925")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211002045943.9406-1-rdunlap@infradead.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At the moment the touch keys have key codes assigned from the device
tree. In some cases, users might want to change the key code from
userspace. There is existing functionality for this in the input core
using the EVIOCSKEYCODE ioctl, which is integrated for example into udev.
Make it possible to use this functionality for tm2-touchkey by simply
making the input core aware of the array that holds the keycodes.
Similar code also exists in mcs_touchkey and mpr121_touchkey.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211013112305.41574-2-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Report the index of pressed touch key as MSC_SCAN code to userspace
so it is possible to identify which of the keys was pressed (not
just the function that is currently assigned to the key).
This is done similarly also in mcs_touchkey and mpr121_touchkey.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211013112305.41574-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes the following warning from sparse:
CC [M] drivers/input/misc/adxl34x.o
CHECK drivers/input/misc/adxl34x.c
drivers/input/misc/adxl34x.c:245:29: warning: cast to restricted __le16
drivers/input/misc/adxl34x.c:248:29: warning: cast to restricted __le16
drivers/input/misc/adxl34x.c:251:29: warning: cast to restricted __le16
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/YWZIjb91d6aAwgss@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By using managed resources (devm) we are able to streamline error handling
in probe and remove most of the custom remove method.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/YWZGKWgdarGtvtYA@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of manually toggling interrupt as wakeup source in suspend/resume
methods, let's declare keypad interrupt and wakeup interrupt and leave the
rest to the PM core.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20211012013735.3523140-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of guarding suspend/resume methods with #ifdef CONFIG_PM
let's mark them as __maybe_unused as this allows better compile
coverage.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20211012013735.3523140-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
