When an i2c-hid device is resumed from system sleep the driver resets
the device to be sure it is in known state. The device is expected to
issue an interrupt when reset is complete.
This reset might take few milliseconds to complete so if the HID driver
on top (hid-rmi) starts to set up the device by sending feature reports
etc. the device might not issue the reset complete interrupt anymore.
Below is what happens to touchpad on Lenovo Yoga 900 during resume from
system sleep:
[ 24.790951] i2c_hid i2c-SYNA2B29:00: i2c_hid_hwreset
[ 24.790973] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 24.790982] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 08
[ 24.793011] i2c_hid i2c-SYNA2B29:00: resetting...
[ 24.793016] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 01
Here i2c-hid sends reset command to the touchpad.
[ 24.794012] i2c_hid i2c-SYNA2B29:00: input: 06 00 01 00 00 00
[ 24.794051] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.794059] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=22 00 3f 03 0f 23 00 04 00 0f 01
Now hid-rmi puts the touchpad to correct mode by sending it a feature
report. This makes the touchpad not to issue reset complete interrupt.
[ 24.796092] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: waiting...
i2c-hid starts to wait for the reset interrupt to trigger which never
happens.
[ 24.798304] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.798313] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=25 00 17 00 09 01 42 00 2e 00 19 19 00 10 cc 06 74 04 0f
19 00 00 00 00 00
Yet another output report from hid-rmi driver.
[ 29.795630] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: finished.
[ 29.795637] i2c_hid i2c-SYNA2B29:00: failed to reset device.
After 5 seconds i2c-hid driver times out.
[ 29.795642] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 29.795649] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 01 08
[ 29.797576] dpm_run_callback(): i2c_hid_resume+0x0/0xb0 returns -61
[ 29.797584] PM: Device i2c-SYNA2B29:00 failed to resume: error -61
After this the touchpad does not work anymore (and also resume itself
gets slowed down because of the timeout).
Prevent sending of feature/output reports while the device is being
reset by adding a mutex which is held during that time.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Nish Aravamudan <nish.aravamudan@gmail.com>
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like 29fae1c85 ("HID: logitech: Add support for G29") was a little
bit aggressive and broke other devices.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=108121
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without quirk keyboard repeats '6' until volume control is used since it
indicates the key is pressed without ever releasing.
Signed-off-by: Jimmy Berry <jimmy@boombatower.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Given that INTUOSHT < BAMBOO_PT
features->type >= INTUOSHT || features->type <= BAMBOO_PT
condition is always true, and therefore device_type is under certain
circumstances wrongly set with WACOM_DEVICETYPE_PAD bit set.
Fix the condition so that it actually represents the range as intended.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
DTU1141 has an extra 1 mm tablet active outbounding area on each
side of the display, same as those recently released DTUs.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
"Highlights:
- Intel Skylake Win8 precision touchpads support fixes/improvements
from Mika Westerberg
- Lenovo Yoga 2 quirk from Ritesh Raj Sarraf
- potential uninitialized buffer access fix in HID core from Richard
Purdie
- Wacom Intuos and Wacom Cintiq 2 support improvements from Jason
Gerecke and Ping Cheng
- initiation of sysfs deprecation process for most of the roccat
drivers, from the roccat support maintiner Stefan Achatz
- quite a few device ID / quirk additions and small fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
HID: logitech: Add support for G29
HID: logitech: Simplify wheel detection scheme
HID: wacom: Call 'wacom_query_tablet_data' only after 'hid_hw_start'
HID: wacom: Fix ABS_MISC reporting for Cintiq Companion 2
HID: wacom: Remove useless conditions from 'wacom_query_tablet_data'
HID: wacom: fix Intuos wireless report id issue
HID: fix some indenting issues
HID: wacom: Expect 'touch_max' touches if HID_DG_CONTACTCOUNT not present
HID: wacom: Tie cached HID_DG_CONTACTCOUNT indices to report ID
HID: roccat: Fixed resubmit: Deprecating most Roccat sysfs attributes
HID: wacom: Report full pressure range for Intuos, Cintiq 13HD Touch
HID: wacom: Add support for Cintiq Companion 2
HID: multitouch: Fetch feature reports on demand for Win8 devices
HID: sensor-hub: Add quirk for Lenovo Yoga 2 with ITE Chips
HID: usbhid: Fix for the WiiU adapter from Mayflash
HID: corsair: boolify struct k90_led.removed
HID: corsair: Add Corsair Vengeance K90 driver
HID: hid-input: allow input_configured callback return errors
HID: multitouch: Add suffix for HID_DG_TOUCHPAD
HID: i2c-hid: Fill in physical device providing HID functionality
...
At present the G29 is mis-identified as a DFGT, this patch ensures
that the wheel is correctly detected and allows setting the LEDs and
turning range via the '/sys' interface.
This wheel can also emulate other types of Logitech wheels.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplfy how hid-logitech driver detects the native mode of the wheel,
done by looking at the USB-ID revision and comparing bit mask.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The input_configured callback was recently changed to return
an 'int', but the newly added driver uses the old API:
drivers/hid/hid-gfrm.c:151:22: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
This changes the driver like the other ones.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 34fc1322e7 ("HID: hid-gfrm: Google Fiber TV Box remote controls")
Fixes: b2c68a2f1b ("HID: hid-input: allow input_configured callback return errors")
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When configuring input device via input_configured callback we may
encounter errors (for example input_mt_init_slots() may fail). Instead
of continuing with half-initialized input device let's allow driver
indicate failures.
Signed-off-by: Jaikumar Ganesh <jaikumarg@android.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com>
Acked-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When connecting the Cintiq Companion 2 as an external tablet (i.e., using
it in "hybrid" mode) it has been seen to cause the kernel of the machine
it is connected to to Oops. The cause has been traced to us attempting to
switch the tablet's mode prior to actually starting HID device (resulting
in the eventual dereference of the uninitialized control URB).
Commit 3b164a0 moved the mode switch from occuring post-start to occurring
pre-start. The change was not seen to cause issues largely due to the fact
that most devices mode switch with 'hid_hw_raw_request' (which is safe to
call prior to start) rather than 'hid_hw_request'.
Moving the call back to its original location resolves the issue, but
causes some touch-only Bamboo tablets (e.g. 056a:00d0) to stop working.
The affected tablets require us to perform a mode switch on their
vestigial pen interface prior ignoring with -ENODEV, meaning that the
code which is responsible for doing the ignoring has to move as well.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The pad handling code introduced for the Cintiq Companion 2 (f7acb55)
looks at the wrong bytes in the report when deciding whether ABS_MISC
should be sent. This does not cause any issues with the X driver now
that the pen and pad have been split to separate devices, but is
incorrect and has caused issues when backporting to distros with pre-
3.17 kernels.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When support for the Cintiq Companion Hybrid and Cintiq Companion 2 was
added (36d3c51 and f7acb55), the 'wacom_query_tablet_data' function was
updated to include references to CINTIQ_HYBRID and CINTIQ_COMPANION_2
with the thought that they were necessary to switch the touch interface
into the proper mode. This is unnecessary, however, since those types
are only ever associated with the pen interface -- the touch interfaces
are either CINTIQ_24HDT or HID_GENERIC. To avoid confusion in the future,
we remove the unnecessary CINTIQ_HYBRID and CINTIQ_COMPANION_2 conditions.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Intuos Pen in wireless mode does not have the same report id (2) as
when it is in USB mode (17).
This patch also moves WIRELESS next to REMOTE in type enum so we
can group devices with similar features easily.
Reported-by: Dale Brewe <dlbrewe@hotmail.com>
Tested-by: Dale Brewe <dlbrewe@hotmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some drivers indent some lines in a very weird manner. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When introduced in commit 1b5d514, the check 'if (hid_data->cc_index >= 0)'
in 'wacom_wac_finger_pre_report' was intended to switch where the driver
got the expected number of contacts from: HID_DG_CONTACTCOUNT if the usage
was present, or 'touch_max' otherwise. Unfortunately, an oversight worthy
of a brown paper bag (specifically, that 'cc_index' could never be negative)
meant that the latter 'else' clause would never be entered.
The patch prior to this one introduced a way for 'cc_index' to be negative,
but only if HID_DG_CONTACTCOUNT is present in some report _other_ than the
one being processed. To ensure the 'else' clause is also entered for devices
which don't have HID_DG_CONTACTCOUNT on _any_ report, we add the additional
constraint that 'cc_report' be non-zero (which is true only if the usage is
present in some report).
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The cached indicies 'cc_index' and 'cc_value_index' introduced in 1b5d514
are only valid for a single report ID. If a touchscreen has multiple
reports with a HID_DG_CONTACTCOUNT usage, its possible that the values
will not be correct for the report we're handling, resulting in an
incorrect value for 'num_expected'. This has been observed with the Cintiq
Companion 2.
To address this, we store the ID of the report those indicies are valid
for in a new 'cc_report' variable. Before using them to get the expected
contact count, we first check if the ID of the report we're processing
matches 'cc_report'. If it doesn't, we update the indicies to point to
the HID_DG_CONTACTCOUNT usage of the current report (if it has one).
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The new Intuos tablets added in eda01da and the Cintiq 13HD Touch added
in b4bf212 are capable of reporting 2048 levels of pressure. Although the
kernel reports the correct range to userspace, an oversight has resulted
in the driver ingoring the 11th pressure bit and only sending pressures
of 0 through 1023.
We could fix this issue by expanding the type check to include these
devices, but it makes much more sense to just have the driver look at
the device's maximum pressure when determining if it should read the
11th bit.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for the EMR (pen+pad) and touchscreen devices used by the
Wacom Cintiq Companion 2. This applies both to using the device as a
standalone system, as well as when operating in "Cintiq mode" (where
the EMR/touchscreen are simply exposed as USB devices to the system
its connected to).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Clifford Jolly <expiredpopsicle@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some newer Intel Skylake based Dell laptops with Win8 precision touchpad
fail when initial feature reports are fetched from it. Below is an example
output with some additional debug included:
i2c_hid i2c-DLL0704:01: Fetching the HID descriptor
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=20 00
i2c_hid i2c-DLL0704:01: HID Descriptor: 1e 00 00 01 99 02 21 00 24 ...
...
i2c_hid i2c-DLL0704:01: i2c_hid_get_report
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=22 00 38 02 23 00
i2c_hid i2c-DLL0704:01: report (len=4): 04 00 08 05
i2c_hid i2c-DLL0704:01: report id 13
i2c_hid i2c-DLL0704:01: i2c_hid_get_report
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=22 00 3d 02 23 00
i2c_hid i2c-DLL0704:01: failed to retrieve report from device.
i2c_hid i2c-DLL0704:01: report id 7
i2c_hid i2c-DLL0704:01: i2c_hid_get_report
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=22 00 37 02 23 00
i2c_hid i2c-DLL0704:01: report (len=259): 03 01 07 fc 28 fe 84 40 ...
i2c_hid i2c-DLL0704:01: report id 4
i2c_hid i2c-DLL0704:01: i2c_hid_get_report
i2c_hid i2c-DLL0704:01: __i2c_hid_command: cmd=22 00 34 02 23 00
We manage to fetch few reports but then the touchpad dies:
i2c_designware i2c_designware.1: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0704:01: failed to retrieve report from device.
it eventually pulls the whole I2C bus low:
i2c_designware i2c_designware.1: controller timed out
i2c_hid i2c-DLL0704:01: failed to set a report to device.
Fix this by preventing initial feature report retrieval for Win8 devices.
Instead we fetch reports as needed in mt_feature_mapping(). This prevents
fetching reports which might cause problems with the device in question.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch is a follow-up to 47eeca8a48 (" HID: sensor-hub: Add in quirk
for Lenovo Yogas with ITE")
The Lenovo Yoga 2 13 seems to be sold in multiple variants with minor
difference3s. IN my case, the USB ID for ITE chip is different than the
Yoga 2 11 and Yoga 3 14.
Without the quirk, no data is received from the accelerometer. I have
verified the patch, testing this on 4.3-rc4 (and 4.2 stable). With this
patch, proper orientation data is received.
rrs@learner:~/Community/UpstreamSources/linux-upstream_GIT (stable-42)$
monitor-sensor
** Message: Accelerometer orientation changed: bottom-up
** Message: Light changed: 0.000000 (lux)
±** Message: Accelerometer orientation changed: left-up
** Message: Accelerometer orientation changed: bottom-up
** Message: Accelerometer orientation changed: left-up
** Message: Accelerometer orientation changed: normal
** Message: Light changed: 29.999999 (lux)
monitor-sensor can be found in the iio-sensor-proxy tool.
Signed-off-by: Ritesh Raj Sarraf <rrs@debian.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The WiiU adapter from Mayflash (see
http://www.mayflash.com/Products/NINTENDOWiiU/W009.html) is not
working correctly.
The "XInput" mode works fine, the controller is recognized as a xbox
controller. But it is only possible to connect one controller with this method.
In "DInput" mode the device is recognized as some kind of mouse input but no
joystick is created. This commit will change this behavior with
HID_QUIRK_MULTI_INPUT to split the device into 4 input devices so that it will
also create joysticks in /dev/input/js*.
Signed-off-by: Oliver Schmitt <voltumna@gmx.net>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch implements a HID driver for the Corsair Vengeance K90 keyboard.
It fixes the behaviour of the keys using incorrect HID usage codes and exposes
the macro playback mode and current profile to the user space through sysfs
attributes. It also adds two LED class devices controlling the "record" LED and
the backlight.
Signed-off-by: Clément Vuchener <clement.vuchener@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When configuring input device via input_configured callback we may
encounter errors (for example input_mt_init_slots() may fail). Instead
of continuing with half-initialized input device let's allow driver
indicate failures.
Signed-off-by: Jaikumar Ganesh <jaikumarg@android.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com>
Acked-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of printing "UNKNOWN" as device suffix for HID_DG_TOUCHPAD call
the device as "Touchpad".
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently hid_connect() prints out following when I2C connected HID devices
is connected:
hid-multitouch 0018:03EB:2136.0001: ... [ATML3432:00 03EB:2136] on
After "on " should read physical device name but it is left empty by the
driver.
Make it look better and fill in the physical device name.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This series of devices supports both pen and touch. It reports
touch data in Bamboo3 format and pen data in Intuos pro format.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-By: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Not all Bamboo support both pen and touch. Make sure we deal with
pen only and touch only devices properly.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-By: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_connect adds various strings to the buffer but they're all
conditional. You can find circumstances where nothing would be written
to it but the kernel will still print the supposedly empty buffer with
printk. This leads to corruption on the console/in the logs.
Ensure buf is initialized to an empty string.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
[dvhart: Initialize string to "" rather than assign buf[0] = NULL;]
Cc: Jiri Kosina <jikos@kernel.org>
Cc: linux-input@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just to prettify the log message. Otherwise it would be <UNKNOWN>.
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for Microsoft Type Cover 3 with 0x07e2 product ID.
Signed-off-by: Donavan Lance <shvr@fedoraproject.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixed HID descriptor for DragonRise Joystick. Replaced default descriptor
which doubles Z axis and causes mixing values of X and Z axes.
Signed-off-by: Maciej Zuk <gzmlke@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Logitech K400 keyboard has an embedded touchpad which is seen as a
mouse from the OS point of view. There is a hardware shortcut to disable
tap-to-click but the setting is not remembered accross reset, annoying
some users.
We can toggle this feature from the host by using the feature 0x6010:
Touchpad FW items
Reported-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HIDPP_QUIRK_DELAYED_INIT means two things currently:
- we want to delay the initialization process
- we do not want hid to create an input device based on the report
descriptor.
This should actually be 2 different quirks so we can have special connect
events while still having HID creating the input for us.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is an error in the report descriptor of the Thinkpad Helix 2 where
logical minimum value (557376) is greater than logical maximum (491200)
for all of the magnetic flux axis data fields. This error results in a
report descriptor parsing failure that causes the sensors attached to the
hub not to be detected.
dmesg excerpt:
[ 19.866905] drivers/hid/hid-core.c: logical range invalid 0x88140 0x77ec0
[ 19.866914] hid-sensor-hub 0018:2047:0855.0007: item 0 1 0 8 parsing failed
[ 19.866926] hid-sensor-hub 0018:2047:0855.0007: parse failed
[ 19.866933] hid-sensor-hub: probe of 0018:2047:0855.0007 failed with error -22
Add a report fixup to change magnetic flux logical minimums to -557376
for the parsing to succeed and the sensors to get detected.
After applying the fix the sensors get detected, with corresponding drivers
(hid-accel-3d,hid-gyro-3d,etc) loaded, and its possible to read their values.
Signed-off-by: Fernando D S Lima <fernandodsl@gmail.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch enables the Saitek HID quirk for the mode button of the Mad Catz
R.A.T.5 gaming mouse by adding the same quirk that's been neeeded for
preivous versions.
[jikos@kernel.org: update changelog a little bit]
Signed-off-by: Harald Brinkmann <hbrinkmann@braincalibration.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device is pad (buttons) only, there is no stylus or touch. Up to
five remotes can pair with the device's associated USB dongle.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Prior to this commit, numbered button bit setting was done separately
for each device type in wacom_setup_pad_capabilities(). Here we add a
numbered_buttons property to the wacom_features struct and extract the
repeated bit setting code to a new function:
wacom_settup_numbered_buttons().
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Enable ELAN0100 touchpad driver, found on a Asus X205TA laptop, to
gai 2,3 fingers tap and 2 fingers scroll.
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Reviewed-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Looks like 0x8882 needs the same quirk than 0x8883.
Given that both devices claim they are "TPV OpticalTouchScreen" rename
the 0x8883 to add its PID in the #define.
Reported-by: Blaine Lee <blaine.j.lee@medtronic.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
