As reported by smatch:
drivers/media/pci/cx25821/cx25821-alsa.c:146 cx25821_alsa_dma_init() warn: should 'nr_pages << 12' be a 64 bit type?
the number of patches should be unsigned long.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media/v4l2-core/videobuf-dma-sg.c:245 videobuf_dma_init_kernel() warn: should 'nr_pages << 12' be a 64 bit type?
The printk should not be using %d for the number of pages.
After looking better, the real problem here is that the
number of pages should be long int.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As warned by smatch:
drivers/media/rc/serial_ir.c:550 serial_ir_probe() warn: should '8 << ioshift' be a 64 bit type?
the "8" constant should be unsigned long.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The usage of castings and float point when checking for
the setup based at the symbol_rate cause those warnings
with smatch:
drivers/media/dvb-frontends/tda10021.c:153 tda10021_set_symbolrate() warn: unsigned 'symbolrate' is never less than zero.
drivers/media/dvb-frontends/tda10021.c:155 tda10021_set_symbolrate() warn: unsigned 'symbolrate' is never less than zero.
drivers/media/dvb-frontends/tda10021.c:157 tda10021_set_symbolrate() warn: unsigned 'symbolrate' is never less than zero.
drivers/media/dvb-frontends/tda10021.c:159 tda10021_set_symbolrate() warn: unsigned 'symbolrate' is never less than zero.
While the code should work with gcc, as it will evaluate the
values into a constant before compiling, other compilers
could do otherwise. So, get rid of float pointing math on it,
avoiding the need of doing typecasts.
While here, cleanup some coding style issues at the related
code.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sparse warns about this symbol:
drivers/media/platform/qcom/venus/hfi_venus.c:133:5: warning: symbol 'venus_fw_debug' was not declared. Should it be static?
Because hfi_venus.c doesn't include a header file with the
extern. So, move it to core.h, with is included by both
hfi_venus.c and dbgfs.c.
This way, if something changes with it, warnings or errors
will be produced.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As reported by smatch:
drivers/media/radio/wl128x/fmdrv_common.c:736 fm_irq_handle_rdsdata_getcmd_resp() warn: potential spectre issue 'rds_fmt.data.groupdatabuff.buff>
Address it by using array_index_nospec().
While here, reorder the linux/ includes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While smatch reports an issue there:
drivers/media/pci/ttpci/av7110_v4l.c:163 ves1820_set_tv_freq() warn: unsigned 'freq' is never less than zero.
drivers/media/pci/ttpci/av7110_v4l.c:165 ves1820_set_tv_freq() warn: unsigned 'freq' is never less than zero.
The logic is actually fine. Yet, removing the typecast
shuts up smatch and makes the code more readable.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As pointed by smatch:
drivers/media/tuners/qt1010.c:239 qt1010_init_meas1() error: uninitialized symbol 'val2'.
drivers/media/tuners/qt1010.c:273 qt1010_init_meas2() error: uninitialized symbol 'val'.
The logic is ok, but it is hard for static analyzers
to parse it, as it depends on a value read in the middle
of a loop.
Also, it takes a while for humans to verify.
Re-write the first function to use a more direct way.
At the second one, I opted to just initialize the read var,
in order to shut up the report.
While here, address a few coding style issues at the
function code.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The original logic had an integer to unsigned integer
conversion, plus a float-point math. While gcc should be
able to do the match at compile time, other compilers might
not do the same. Also, those produce the following warnings
with static code analyzers:
drivers/media/dvb-frontends/tda10086.c:300 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:303 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:306 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:309 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:312 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:315 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:318 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:321 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:324 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
drivers/media/dvb-frontends/tda10086.c:327 tda10086_set_symbol_rate() warn: unsigned 'symbol_rate' is never less than zero.
Change the logic to declare the reference constant as unsigned
and to not use float point math.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Here we introduce debug prefixes for dev_dbg groups by level of
importance - Venus{Low,Med,High,FW} Enabling the particular level
will be done by dynamic debug.
For example to enable debug messages with low level:
echo 'format "VenusLow" +p' > debugfs/dynamic_debug/control
If you want to enable all levels:
echo 'format "Venus" +p' > debugfs/dynamic_debug/control
All the features which dynamic debugging provide are preserved.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This will be useful when debugging specific issues related to
firmware HFI interface.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the standard menu control for frame skip mode in the MFC
driver. The legacy private menu control is kept for backward
compatibility.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This adds support for frame-skip-mode standard v4l2 control in
encoder driver. The control is implemented based on the
combination of client selected bitrate-mode and frame-skip-mode.
Once The client selected bitrate-mode (constant or variable) and
the frame-skip-mode is not disabled we set variable framerate for
rate controller.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adds encoders standard v4l2 control for frame-skip. The control
is a copy of a custom encoder control so that other v4l2 encoder
drivers can use it.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adds implementation of V4L2_CID_MPEG_VIDEO_CONSTANT_QUALITY v4l
control when the bitrate mode is CQ.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When V4L2_CID_MPEG_VIDEO_BITRATE_MODE value is
V4L2_MPEG_VIDEO_BITRATE_MODE_CQ, encoder will produce
constant quality output indicated by
V4L2_CID_MPEG_VIDEO_CONSTANT_QUALITY control value.
Encoder will choose appropriate quantization parameter
and bitrate to produce requested frame quality level.
Signed-off-by: Maheshwar Ajja <majja@codeaurora.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the recovery mechanism is using two hfi functions
to destroy and create interface queues. For the purpose of
recovery we don't need to free and allocate the memory used
for interface message queues, that's why we introduce new
function which just reinit the queues. Also this will give
to the recovery procedure one less reason to fail (if for
some reason we couldn't allocate memory).
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After power domains and clock restructuring the recovery for
sdm845 and v4 did not work properly. Fix that by reworking the
recovery function and the sequence.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the hfi_parser has been called only once during driver
probe. To prepare the parser function to be called multiple times
from recovery we need to initialize few variables which are used
during parsing time.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On dragonboard-410c (apq8016) with HFI_VERSION_1XX, the reported
framerate is in unit of 1/65535 fps (for fine grained control).
So the current reported supported frame intervals is wrong (max
is 1/65535 fps), leading to encoding issues or format negotiation
failures with gstreamer.
Fix that by setting the framerate denominator to coherent value
based on the the framerate factor.
The factor is not always the same, e.g. with db820c (apq8096) HFI
reports framerate in fps unit. So only apply that for HFI_VERSION_1XX.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are few list handling issues while adding and deleting
node in the registered buf list in the driver.
1. list addition - buffer added into the list during buf_init
while not deleted during cleanup.
2. list deletion - In capture streamoff, the list was reinitialized.
As a result, if any node was present in the list, it would
lead to issue while cleaning up that node during buf_cleanup.
Corresponding call traces below:
[ 165.751014] Call trace:
[ 165.753541] __list_add_valid+0x58/0x88
[ 165.757532] venus_helper_vb2_buf_init+0x74/0xa8 [venus_core]
[ 165.763450] vdec_buf_init+0x34/0xb4 [venus_dec]
[ 165.768271] __buf_prepare+0x598/0x8a0 [videobuf2_common]
[ 165.773820] vb2_core_qbuf+0xb4/0x334 [videobuf2_common]
[ 165.779298] vb2_qbuf+0x78/0xb8 [videobuf2_v4l2]
[ 165.784053] v4l2_m2m_qbuf+0x80/0xf8 [v4l2_mem2mem]
[ 165.789067] v4l2_m2m_ioctl_qbuf+0x2c/0x38 [v4l2_mem2mem]
[ 165.794624] v4l_qbuf+0x48/0x58
[ 1797.556001] Call trace:
[ 1797.558516] __list_del_entry_valid+0x88/0x9c
[ 1797.562989] vdec_buf_cleanup+0x54/0x228 [venus_dec]
[ 1797.568088] __buf_prepare+0x270/0x8a0 [videobuf2_common]
[ 1797.573625] vb2_core_qbuf+0xb4/0x338 [videobuf2_common]
[ 1797.579082] vb2_qbuf+0x78/0xb8 [videobuf2_v4l2]
[ 1797.583830] v4l2_m2m_qbuf+0x80/0xf8 [v4l2_mem2mem]
[ 1797.588843] v4l2_m2m_ioctl_qbuf+0x2c/0x38 [v4l2_mem2mem]
[ 1797.594389] v4l_qbuf+0x48/0x58
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The H.264 specification requires in section 7.4.3 "Slice header semantics",
that the following values shall be the same in all slice headers:
pic_parameter_set_id
frame_num
field_pic_flag
bottom_field_flag
idr_pic_id
pic_order_cnt_lsb
delta_pic_order_cnt_bottom
delta_pic_order_cnt[ 0 ]
delta_pic_order_cnt[ 1 ]
sp_for_switch_flag
slice_group_change_cycle
These bitstream fields are part of the slice header, and therefore
passed redundantly on each slice. The purpose of the redundancy
is to make the codec fault-tolerant in network scenarios.
This is of course not needed to be reflected in the V4L2 controls,
given the bitstream has already been parsed by applications.
Therefore, move the redundant fields to the per-frame decode
parameters control (DECODE_PARAMS).
Field 'pic_parameter_set_id' is simply removed in this case,
because the PPS control must currently contain the active PPS.
Syntax elements dec_ref_pic_marking() and those related
to pic order count, remain invariant as well, and therefore,
the fields dec_ref_pic_marking_bit_size and pic_order_cnt_bit_size
are also common to all slices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
DPB entry PicNum maximum value is 2*MaxFrameNum for interlaced
content (field_pic_flag=1).
As specified, MaxFrameNum is 2^(log2_max_frame_num_minus4 + 4)
and log2_max_frame_num_minus4 is in the range of 0 to 12,
which means pic_num should be a 32-bit field.
The v4l2_h264_dpb_entry struct needs to be padded to avoid a hole,
which might be also useful to allow future uAPI extensions.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As discussed recently, the current interface for the
Decoded Picture Buffer is not enough to properly
support field coding.
This commit introduces enough semantics to support
frame and field coding, and to signal how DPB entries
are "used for reference".
Reserved fields will be added by a follow-up commit.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The prediction weight parameters are only required under
certain conditions, which depend on slice header parameters.
As specified in section 7.3.3 Slice header syntax, the prediction
weight table is present if:
((weighted_pred_flag && (slice_type == P || slice_type == SP)) || \
(weighted_bipred_idc == 1 && slice_type == B))
Given its size, it makes sense to move this table to its control,
so applications can avoid passing it if the slice doesn't specify it.
Before this change struct v4l2_ctrl_h264_slice_params was 960 bytes.
With this change, it's 188 bytes and struct v4l2_ctrl_h264_pred_weight
is 772 bytes.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The unit of exposure value is different from other OmniVision sensors,
driver will divide by 2 before set register, the exposure range exposed
by v4l2 ctrl to user should be same as others, so the calculation for
the maximum exposure value in current driver need be fixed.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make use of SCCB APIs for regmap operations.
Remove i2c_check_functionality as devm_regmap_init_sccb
does it for us.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
1) the numerator and/or denominator might be 0, in that case
fall back to the default frame interval. This is per the spec
and this caused a v4l2-compliance failure.
2) the updated frame interval wasn't returned in the s_frame_interval
subdev op.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
clang static analysis reports this error
m5mols_core.c:767:4: warning: Called function pointer
is null (null dereference) [core.CallAndMessage]
info->set_power(&client->dev, 0);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In other places, the set_power ptr is checked.
So add a check.
Fixes: bc125106f8 ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the error return from the call to max9286_read is masked
with 0xf0 so the following check for a negative error return is
never true. Fix this by checking for an error first, then masking
the return value for subsequent conflink_mask checking.
Addresses-Coverity: ("Logically dead code")
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Although the code is correct and doing the right thing, the clock diagram
showed the wrong register for the bit divider, which had me doubting the
understanding of the tree. Fix this to avoid doubts in the future.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Fixes: aa2882481c ("media: ov5640: Adjust the clock based on the expected rate")
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OTP data was not ready after registered as nvmem device, it is
risky as the nvmem read may happen once the device exists, this patch
get the OTP data ready before registering the nvmem device. OTP data
missing should not break the normal camera sensor probe, so use a
warning instead of an error message.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Suggested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
vidioc_streamoff can be called multiple times from userspace, but we
should only call media_pipeline_stop when we're actually setup.
This became more noticeable after commit 2a2599c663 ("[media] media:
entity: Catch unbalanced media_pipeline_stop calls") was merged as it
added a WARN for unbalanced calls to media_pipeline_stop.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is no longer used since the conversion to DT
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a no-op as it is never set and is a remnant from non-DT days
that can be safely removed.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some devices, there may be multiple camera sensors attached
to the same port. Make sure we probe all of them, not just the
first one.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of keeping a local copy of how many sensors we've probed
(which may not even properly represent the number of sensors
probed if we have a port without a sensor), use the global
num_sensors counter that has the actual number used.
This will also make it easier to add support for multiple sensors
being connected to the same port.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit ee7160e57c ("[media] s5p-fimc: Add support for JPEG capture")
added support for JPEG capture, but missed setting a register when the
parallel port was used rather than the CSIS device.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit bae4500399 ("[media] exynos4-is: Add missing entity function
initialization") tried to suppress the warnings such as
s5p-fimc-md camera: Entity type for entity FIMC.0 was not initialized!
However, this missed setting for the subdev. Set it now to avoid the
ugly warnings on boot.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Not all devices use the CSIS device, some may use the FIMC directly in
which case the CSIS device isn't registered. This leads to a nullptr
exception when starting the stream as the CSIS device is always
referenced. Instead, if getting the CSIS device fails, try getting the
FIMC directly to check if we are using the subdev API
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On FIMC variants which don't have writeback channel, there is no need to
access system registers. This patch makes the driver request sysreg
regmap conditionally depending on whether writeback is supported.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The S5PV210 platform only supports device tree based booting
where the FIMC variant data is parsed directly from
the device tree, hence the now unused static data can be removed.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
list_for_each_entry is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry is defined in terms of list_first_entry,
which indicates that it should not be used on an empty list. But in
list_for_each_entry, the element obtained by list_first_entry is not
really accessed, only the address of its list_head field is compared
to the address of the list head, so the list_first_entry is safe.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
iterator name list_for_each_entry;
statement S;
identifier i;
@@
-if (!(list_empty(x))) {
list_for_each_entry(i,x,...) S
- }
... when != i
? i = e
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
