Some devices are using the MMC1 pins 4..8 as GPIO pins, and in
this case they need to be configured for 1.8V IO voltage if not
done by the bootloader as otherwise some devices like smsc911x
won't work properly.
Let's also make sure this register is saved and restored for
idle.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4, OMAP5 and DRA7 now parse DT entries for control module address spaces,
and set up syscon mappings appropriately. Low level IO init is updated to
remove the legacy control module mappings for these devices also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
omap4_ctrl_pad_readl/writel are no longer used by anybody, so remove
these. Syscon / pinctrl should be used to access the padconf area
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates an l4_wkup interconnect for AM43xx, and moves some of
the generic peripherals under it. System control module nodes are moved
under this new interconnect also, and the SCM clock layout is changed
to use the renamed SCM nodea as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates an l4_wkup interconnect for AM33xx, and moves some of
the generic peripherals under it. System control module nodes are moved
under this new interconnect also, and the SCM clock layout is changed
to use the renamed SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates an l4_core interconnect for OMAP3, and moves some
of the generic peripherals under it. System control module nodes are
moved under this new interconnect also, and the SCM clock layout
is changed to use the renamed SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
This patch creates an l4 / l4-wkup interconnects for omap2420 / omap2430
SoCs, and moves some of the generic peripherals under it. System control
module nodes are moved under this new interconnect also, and the SCM
clock layout is changed to use the new SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Control module driver needs to support syscon for register accesses, as
the DT hierarchy for control module driver is going to be changed. All
the control module related features will be moved under control module
node, including clocks, pinctrl, and generic configuration register
access. Temporary iomap is still provided very early in the boot for
access while syscon is not yet ready.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Some of the TI clock providers will be converted to use syscon, thus
low-level regmap support is needed for the clock drivers also. This
patch adds this support, which can be enabled for individual drivers
in later patches.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is no need to provide the control module base address through a
low-level API from the low-level IO init, as this information is
available through DT. This patch adds a new API to initialize the
control module though, but mostly makes the old API obsolete. The
old API can be completely removed once OMAP3 is made DT only.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Splits the clock related provider module inits under their own driver files.
Previously this was done for all modules under the common PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Fix coding style problems in arch/arm/mach-omap2/control.c.
Signed-off-by: Jeremy Vial <jvial@adeneo-embedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the comment “restore_es3: applies to 34xx >= ES3.0" in
"arch/arm/mach-omap2/sleep34xx.S”, omap3_restore_es3 should be used
if the revision of an OMAP34xx is ES3.1.2.
Signed-off-by: Jeremy Vial <jvial@adeneo-embedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Control module related PM initializations are now moved within control
module driver. Done in preparation to isolate the code to its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3 PM core requires IVA2 bootmode to be set to idle during init. Currently,
a direct register write is used for this. Add a new ctrl API for this purpose
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP3 PM code for off-mode currently saves the scratchpad contents for CM
registers within OMAP control module driver. However, as we are separating
CM code into its own driver, this must be moved also. This patch adds a
new API for saving the CM scratchpad contents and uses this from the high
level scratchpad save function.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Support for OMAP5 is added to the omap_dsp_ctrl_write_boot_addr()
to enable the DSP boot.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c. In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Prepares for the future move of the PRM/CM code to drivers/. Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.
Basic test logs for this branch on top of v3.7-rc2 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/
But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base. With reverts, fixes,
and workarounds applied as documented in:
http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt
the following test logs were obtained:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=asxx
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-a-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-prcm
The first set of OMAP PRM/CM-related cleanup patches for 3.8.
Prepares for the future move of the PRM/CM code to drivers/. Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.
Basic test logs for this branch on top of v3.7-rc2 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/
But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base. With reverts, fixes,
and workarounds applied as documented in:
http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt
the following test logs were obtained:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/Makefile
arch/arm/mach-omap2/clockdomain2xxx_3xxx.c
arch/arm/mach-omap2/pm24xx.c
Move OMAP3xxx-specific CM functions & macros into cm3xxx.[ch] and
OMAP2xxx-specific macros into cm2xxx.[ch]. Move basic CM register
access functions into static inline functions in cm2xxx_3xxx.h,
leaving only OMAP2/3 hardreset functions in cm2xxx_3xxx.c.
As part of this, split the CM and hwmod code that waits for devices to
become ready into SoC-specific functions.
This is in preparation for the upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move OMAP3xxx-specific PRM functions & macros into prm3xxx.[ch] and
OMAP2xxx-specific macros into prm2xxx.h. (prm2xxx.c will be created
by a subsequent patch when it's needed.) Move basic PRM register
access functions into static inline functions in prm2xxx_3xxx.h, leaving
only OMAP2/3 hardreset functions in prm2xxx_3xxx.c.
Also clarify the initcall function naming to reinforce that this code
is specifically for the PRM IP block.
This is in preparation for the upcoming powerdomain series and the
upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Remove arch/arm/plat-omap/include/plat/sdrc.h by folding its contents
into arch/arm/mach-omap2/sdrc.h. The objective is to assist Tony in
cleaning out arch/arm/plat-omap/, as his upstreams request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[tony@atomide.com: updated to remove rotate macros]
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SCM contains boot addr and boot mode registers to control
other processors on different OMAP versions. It controls the
boot address and mode for DSP based subsystems like: IVA 2.1
(OMAP2430), IVA 2.2 (OMAP3) and DSP (OMAP4).
If contained within SCM registers, when a processor is
booting it uses BOOTADDR to start running the code at that
location. BOOTMOD register specifies a different set of
modes for the processor to execute when booting (from direct,
idle, self-loop, user and default).
Since there was no offset associated with OMAP4, this patch
defines it.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 9890ce44 (ARM: get rid of asm/irq.h in asm/prom.h)
removed include of asm/irq.h in asm/prom.h. This commit
together with recent omap cleanup to remove io.h causes
build breakage:
arrch/arm/mach-omap2/control.c: In function 'omap3_ctrl_write_boot_mode':
arch/arm/mach-omap2/control.c:238: error:
'OMAP343X_CTRL_BASE' undeclared (first use in this function)
...
Fix this by including hardware.h directly where needed
instead of relying on asm/irq.h in asm/prom.h.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to have these defines in plat/io.h.
Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.
While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise we can't do generic map_io as we currently rely on
static mappings that work only because of arch_ioremap.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upon return from off-mode, the ROM code jumps to a restore function
saved in the scratchpad. Based on SoC revision or errata, this
restore entry point is different. Current code uses some helper
functions in sleep34xx.S (get_*_restore_pointer) to get the restore
function entry point.
When returning from off-mode, this code is executed from SDRAM, so
there's no reason to use these helper functions when using the SDRAM
entry points directly would work just fine.
This patch uses ENTRY/ENDPROC to create "real" entry points for these
functions, and uses those values directly when writing the scratchpad.
Tested all three entry points
- restore_es3: 3430/n900
- restore_3630: 3630/Zoom3
- restore: 3530/Overo
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per OMAP3 erratum (i671), ROM code adds extra latencies while
restoring CM_AUTOIDLE_PLL register, if AUTO_PERIPH_DPLL is equal to 1.
This patch stores 0's in scratchpad content area corresponding to
AUTO_PERIPH_DPLL, to prevent ROM code to try to lock per DPLL, since
it won't respect proper programing scheme.
This register is then stored in prcm context. The saving and restore
is now done by kernel side.
Here follow the erratum description
DESCRIPTION
After OFF mode transition, among many restorations, the ROM Code restores the
CM_AUTOIDLE_PLL register, and after that, it tries to relock the PER DPLL.
In case the restoration data stored in scratchpad memory contains a field
CM_AUTOIDLE_PLL.AUTO_PERIPH_DPLL = 1, then the way the ROM Code restores and
locks the PER DPLL does not respect the PER DPLL programming scheme.
In that case, the DPLL might not lock. Meanwhile, when trying to lock the PER
DPLL, the ROM Code does not hang. Only extra latencies are introduced at
wake-up.
WORKAROUND
When saving the context-restore structure in scratchpad memory, in order to
respect the PER DPLL programming scheme, it is advised to store 0 in the
CM_AUTOIDLE_PLL.AUTO_PERIPH_DPLL field of the saved structure.
After wake-up, the application should store in CM_AUTOIDLE_PLL register the
right desired value.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The saving of CCR.CM_AUTOIDLE_PLL is done in scratchpad area.
However, in current code, the saving is done for CM_AUTOIDLE2_PLL
(offset 0x34) instead of CM_AUTOIDLE_PLL (offset 0x30).
This patch changes the code to save the correct register.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move the padconf save code from pm34xx.c to the System Control Module
code in mach-omap2/control.c. This is part of the general push to
move direct register access from middle-layer core code to low-level
core code, so the middle-layer code can be abstracted to work on
multiple platforms and cleaned up.
In the medium-to-long term, this code should be called by the mux
layer code, not the PM idle code. This is because, according to the
TRM, saving the padconf only needs to be done when the padconf
changes[1].
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
1. OMAP34xx Multimedia Device Silicon Revision 3.1.x [Rev. ZH] [SWPU222H]
Section 4.11.4 "Device Off-Mode Sequences"
Now that OMAP4-specific PRCM functions have been added, distinguish the
existing OMAP2/3-specific PRCM functions by prefixing them with "omap2_".
This patch should not result in any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
In preparation for adding OMAP4-specific PRCM accessor/mutator
functions, split the existing OMAP2/3 PRCM code into OMAP2/3-specific
files. Most of what was in mach-omap2/{cm,prm}.{c,h} has now been
moved into mach-omap2/{cm,prm}2xxx_3xxx.{c,h}, since it was
OMAP2xxx/3xxx-specific.
This process also requires the #includes in each of these files to be
changed to reference the new file name. As part of doing so, add some
comments into plat-omap/sram.c and plat-omap/mcbsp.c, which use
"sideways includes", to indicate that these users of the PRM/CM includes
should not be doing so.
Thanks to Felipe Contreras <felipe.contreras@gmail.com> for comments on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For some reason, the PRCM context save/restore code also saves and
restores a single System Control Module register,
CONTROL_PADCONF_SYS_NIRQ. This is probably just an error -- the
register should be handled by SCM code -- so this patch moves it
there.
If this register really does need to be saved and restored before the
rest of the PRCM registers, the code to do so should live in the SCM
code, and the PM code should call this separate function. This
register pertains to devices with a stacked modem, so this patch is
unlikely to affect most OMAP devices out there.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Get rid of the open-coded scratchpad write in mach-omap2/prcm.c and
replace it with an actual API, omap3_ctrl_write_boot_mode(). While
there, get rid of the gratuitous omap_writel().
There's not much documentation available for what should wind up in
the scratchpad here, so more documentation would be appreciated.
Also, at some point, we should formalize our treatment of the scratchpad;
right now, accesses to the scratchpad are not well-documented.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
- Reworked and simplified the execution paths for better
readability and to avoid duplication of code,
- Added comments on the entry and exit points and the interaction
with the ROM code for OFF mode restore,
- Reworked the existing comments for better readability.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Erratum id: i608
RTA (Retention Till Access) feature is not supported and leads to device
stability issues when enabled. This impacts modules with embedded memories
on OMAP3630
Workaround is to disable RTA on boot and coming out of core off.
For disabling RTA coming out of off mode, we do this by overriding the
restore pointer for 3630 as the first point of entry before caches are
touched and is common for GP and HS devices. To disable earlier than
this could be possible by modifying the PPA for HS devices, but not for
GP devices.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[ambresh@ti.com: co-developer]
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
This patch fixes sparse warnings due to non declaration of
static structures and variables.
Sparse warning logs fixed:
arch/arm/mach-omap2/control.c:88:6: warning: symbol 'omap3_secure_ram_storage' was not declared. Should it be static?
n
arch/arm/mach-omap2/timer-gp.c:50:22: warning: symbol 'gptimer_wakeup' was not declared. Should it be static?
arch/arm/mach-omap2/timer-gp.c:240:18: warning: symbol 'omap_timer' was not declared. Should it be static?
arch/arm/mach-omap2/prcm.c:121:24: warning: symbol 'prcm_context' was not declared. Should it be static?
arch/arm/mach-omap2/mux2420.c:510:29: warning: symbol 'omap2420_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux2430.c:589:29: warning: symbol 'omap2430_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:934:28: warning: symbol 'omap3_cus_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1080:29: warning: symbol 'omap3_cus_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1272:28: warning: symbol 'omap3_cbb_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1393:29: warning: symbol 'omap3_cbb_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1603:28: warning: symbol 'omap36xx_cbp_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1821:29: warning: symbol 'omap36xx_cbp_ball' was not declared. Should it be static?
arch/arm/mach-omap2/pm-debug.c:165:15: warning: symbol 'pm_dbg_dir' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:587:30: warning: symbol 'ads7846_config' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:606:23: warning: symbol 'omap3evm_spi_board_info' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:46:25: warning: symbol 'rx51_sdrc_params' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:211:25: warning: symbol 'rx51_get_sdram_timings' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3touchbook.c:64:15: warning: symbol 'touchbook_revision' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:350:24: warning: symbol 'am3517_evm_dss_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3stalker.c:567:23: warning: symbol 'omap3stalker_spi_board_info' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.
This APIs will work only for OMAP4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On omap4 control module is divided in four IP blocks.
- CTRL_MODULE_CORE 0x4a002000
- CTRL_MODULE_PAD_CORE 0x4a100000
- CTRL_MODULE_WKUP 0x4a30c000
- CTRL_MODULE_PAD_WKUP 0x4a31e000
Addressing all the modules with single base address is not possible
considering 16 bit offsets. The mux code manages the pad core and pad
wakeup related base address inside the mux framework. For other usage
only control core and control pad bases are necessary. So this patch
maps only needed pad control base address which is used by device drivers
and infrastructure code
The main control core base is still kept same in this patch to
keep git-bisect working. This will be fixed in the relevant patch
in this series.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
This is a clean-up patch towards dynamic allocation of IO space
instead of using harcoded macros to calculate virtual addresses.
Also update the sdrc, prcm and control module to allocate
iospace dynamically
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
