Tx queue locking was very simple until now.
Multi-channel support will require a more flexible
and fine grained control.
This introduces a per-hw and per-vif (each with a
bitmask of reasons) tx queue locking.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The chanctx API will allow ath10k to support
multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Number of channels is stored in a separate macro
in a header file and channel list is constructed
independently. The macro is used to define survey
array.
This fixes a recent regression introduced after
adding support for 144 channel. The regression
would lead to a warning and incomplete survey data
on channel 165:
chan info: invalid frequency 5825 (idx 38 out of bounds)
Also make sure to enforce the sizes and avoid this
kind of problem in the future.
Fixes: 4a7898fed5 ("ath10k: enable channel 144 on 5GHz band")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added, respectively 'ret'
renamed, and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While debugging something else I noticed AID was
set to 0. This could lead to powersave issues in
station mode. Maybe this isn't really necessary
but set it properly just to be sure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Don't use literal values for offsets. While at it
rename a function so it is more clear what it
checks for.
This finally takes care of the last magic
5GHz/OFDM offset.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's possible to derive rate index from bitrate
without any additional mapping structures/logic.
This should have little to none impact on
performance since this is only done for management
frames and the previous approach wasn't
particularly optimized.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using a hacky table and magic values
use supported band information advertised to
mac80211.
This may impact performance a little when dealing
with legacy rx rates depending on system
architecture. It's probably negligible.
This also fixes a highly theoretical corner case
when HT/VHT rates weren't reported correctly if
channel frequency wasn't known.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the existing ieee80211_rate array instead of
definining separate one. This gets rid of the ugly
4-index offset when dealing with 5GHz band.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using raw values is discouraged. Having
defines/enums is preferred.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was superfluous and confusing. It's better to
define the structure explicitly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to store rate values in hw_value.
This frees up the hw_value for better future use.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Prepare the code for future changes so that new
code can refer to rate-related stuff without
forward declarations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch introduces tdls without tdls peer uapsd and tdls channel switching.
Transmitting tdls data frames works only for ethernet type frames, that's why
data addressed to tdls sta is in ethernet format.
This patch depends on commit c23e31cf7b ("mac80211: initialize rate control
earlier for tdls station").
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently station counting functions
(inc_num_stations/dec_num_stations) does not handle
tdls type of stations. Tdls station should be counted
because it consumes peer in firmware. Only not tdls
stations are excluded from this counting.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Peer type was hardcoded to default value.
For future implementation it is required
to make is configurable.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are a few different tx paths depending on
firmware and frame itself.
Creating a uniform decision will make it possible
to switch between different txmode easier, both
for testing and for future features as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If htt.freq isn't cleared and contains garbage fw
may discard tx packets. Prevent this from
happening by clearing htt.freq properly.
Possible manifestation of the problem could be not
being able to send auth request/response frames on
firmware with HTT >= 3.4 (when freq param was
introduced), e.g. on qca6174.
Fixes: 8d6d362436 ("ath10k: fix offchan reliability")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Patch "ath10k: introduce basic tdls functionality" depends on this mac80211
patch:
c23e31cf7b mac80211: initialize rate control earlier for tdls station
Add support for WOW disconnect and magic-packet.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that ANI is enabled by default, allow user to disable or enable ANI feature
from debugfs
echo 0|1 > /sys/kernel/debug/ieee80211/phyX/ath10k/ani_enable
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ANI helps to improve connectvity and performance in a noisy environment.
Enabling this feature would help the user experience a better and stable
wireless connection in a noisy environmnet. This feature is currently not
enabled for ath10k. Enable this feature by default.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable channel 144 on 5GHz band since 802.11ac introduced it.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Thermal throttling is not handled in software restart and device
bootup. Also it needs to be configured whenever quiet period got
updated. Fix that.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default rts protection is enabled in firmware for the second
rateset. Currently ath10k selects RTS profile (only for software
retries), when legacy stations are associated or asked by mac80211.
On congested environment, when AP is running in HT/VHT mode and
there are no legacy clients associated, this will impact the
robustness. Also enabling RTS protection only for second rateset will
not impact performance on clear environment. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setup maximum number of associated stations supported in
AP/P2P_GO mode.
This allow hostapd/wpa_supplicant to play with that limit
and set more information (eg. P2P group limit bit for P2P_GO).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
NativeWifi tx mode expects QoS Data frames to be
delivered as Data frames with QoS part (e.g. tid)
being delievered out-of-band in fw tx command.
The QoS bit wasn't stripped before submitting to
firmware.
Stripping fixes two known problems:
* qca6174 IOT with some APs, e.g.
Cisco AIR-AP 1252 (which would crash after
ath10k association). Some ath9k APs would
crash as well.
* sniffing own tx frames via radiotap because,
e.g. wireshark was seeing QoS bit set but
since QoS Control was stripped in ath10k it
would parse beginning of LLC/SNAP
>From debugability point of view this removes the
ability to distinguish QoS from non-QoS frames
when sniffing own tx via radiotap. On the other
hand frames can be now parsed correctly without
special software modification.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While testing with older supplicant, .drv_set_key() was failing due to
higher than ath10k firmware could handle key_index (WMI_MAX_KEY_INDEX == 3).
--
wpa_driver_nl80211_set_key: ifindex=15 alg=4 addr=0x7f02b129fbe3 key_idx=4 set_tx=0 seq_len=6 key_len=16
broadcast key
nl80211: set_key failed; err=-22 Invalid argument)
wlan0: WPA: Failed to configure IGTK to the driver
wlan0: RSN: Failed to configure IGTK
--
In order to fix this case (PMF: AES-CMAC/IGTK) force the AES_CMAC cipher to
be handled by software.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions (e.g. qca6174 with fw73)
don't deliver beacons to host reliably. This
causes random disconnects even in perfect
conditions. This is most visible with
multi-channel operation.
All available firmware revisions seem to support
beacon miss offloading so there shouldn't be any
problems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 370e567363 ("ath10k: fix broken traffic for 802.1x in client mode")
introduced a regression on WPA crypto. All keys were treated as if they were
WEP which resulted in WPA being incorrectly installed to fw/hw and subsequently
no traffic.
Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 548462133d ("ath10k: fix interrupt storm") introduced a
regression. The condition responsible for bringing up monitor vdev was broken
and it was never started for CAC so effectivelly CAC would not detect radar
pulses.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mistakenly v1 of `ath10k: fix AP/IBSS CSA with
template based fw`
(81a9a17db5) was
applied.
This patch applies the missing bits from v2:
* remove unnecessary locking
* add some (sanity) checks
There are no practical functionality differences
between v1 and v2.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Promiscuous mode is enabled when wlan interface is added to
bridge. ath10k creates a monitor mode when promiscuous mode
is enabled. When monitor vdev is running along with other
vdev(s) there is a huge number of interrupts generated
especially in noisy condition. Fix this by not enabling
promiscuous(monitor) mode when already a vdev is running.
As disabling promiscuous mode may have issues with 4-address
bridging in STA mode, the change is done specific to non-sta/ibss
mode types. This does not change the support of virtual interface of
type monitor along with other vdevs of any type.
This could fix management frame drop in fw due to unavailable
buffers because in monitor mode device receives everything seen
on the air. In noisy condition, disabling monitor mode helps assoc
go through without any issue.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patches does not modify any functionality. Just a code move
so that ath10k_vdev_stop() can be used in ath10k_vdev_start_restart()
for any failure cases which involves vdev_stop().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This improves coexistance with 11b legacy devices
on wmi-tlv and qca6174.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't report a complete and
ready-to-use vht cap. Instead the driver is
supposed to fill in the missing bits related to
number of chains.
This effectively increases Compressed Steering
Number and Number of Sounding Dimensions in
AssocReq frames for devices with more than one RF
chain and should improve TxBF performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When WEP keys are uploaded it's possible that
there are stations associated already (e.g. when
merging) without any keys. Static WEP needs an
explicit per-peer key upload.
Make sure to re-upload wep keys if necessary.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When running 802.1x WEP keys must be installed
without pairwise-groupwise swap (which is
necessary for static WEP).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 with wmi-tlv firmware uses offloaded
beaconing scheme (i.e. templates). This requires a
little different approach when implementing CSA.
Add missing code to update CS count and report CSA
completion to mac80211. Without it channel switch
was never finished.
To avoid races during interface teardown data_lock
has been used to protect is_up and is_started so
they can be compared against before scheduling
count down work.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not all firmware revisions have a proper
multi-interface client powersaving implementation,
e.g. qca6174 WLAN.RM.2.0-00073.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6184 WLAN.RM.2.0-00073 has a bug in sta
powersave state machine and requires peer param to
be poked to enable the powersave.
Calling this unconditionally should be safe for
other chips/firmwares.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
802.11ad adds new a network type (PBSS) and changes the capability
field interpretation for the DMG (60G) band.
The same 2 bits that were interpreted as "ESS" and "IBSS" before are
re-used as a 2-bit field with 3 valid values (and 1 reserved). Valid
values are: "IBSS", "PBSS" (new) and "AP".
In order to get the BSS struct for the new PBSS networks, change the
cfg80211_get_bss() function to take a new enum ieee80211_bss_type
argument with the valid network types, as "capa_mask" and "capa_val"
no longer work correctly (the search must be band-aware now.)
The remaining bits in "capa_mask" and "capa_val" are used only for
privacy matching so replace those two with a privacy enum as well.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
[rewrite commit log, tiny fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If firmware advertises support for TxBF then the
driver has to instruct the firmware accordingly
during runtime. Without this patch connecting to
an AP with beamformer support would yield abysmal
Rx performance.
This has been tested with wmi-tlv and qca6174
while acting as a STA beamformee only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't notify host about
self-bss-peer removal until after associated vdev
is deleted. This has been observed with qca6174
WLAN.RM.2.0-00073 firmware.
This patch fixes AP teardown slowdowns and
prevents delays and warnings:
ath10k_pci 0000:00:05.0: failed to remove peer for AP vdev 0: -110
ath10k_pci 0000:00:05.0: removing stale peer xx:xx:xx:xx:xx:xx from vdev_id 0
ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 24
ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 8
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A bit of general cleanup to make debug messages more useful.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case firmware fails to start the scan, then complete
the start condition and clean up so that driver does not
block on timeout.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
iwlwifi:
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
* add support for beamforming
* enable stuck queue detection for iwlmvm
* a few fixes for EBS scan
* fixes for various failure paths
* improvements for TDLS Offchannel
wil6210:
* performance tuning
* some AP features
brcm80211:
* rework some code in SDIO part of the brcmfmac driver related to
suspend/resume that were found doing stress testing
* in PCIe part scheduling of worker thread needed to be relaxed
* minor fixes and exposing firmware revision information to
user-space, ie. ethtool.
mwifiex:
* enhancements for change virtual interface handling
* remove coupling between netdev and FW supported interface
combination, now conversion from any type of supported interface
types to any other type is possible
* DFS support in AP mode
ath9k:
* fix calibration issues on some boards
* Wake-on-WLAN improvements
ath10k:
* add support for qca6174 hardware
* enable RX batching to reduce CPU load
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU1fUoAAoJEG4XJFUm622bnjMH/25f2kyLAJSLJmiIhpEcYlNJ
CJMAYsSTcqhKaMEbx742StUUDH3pa1oV4mQ5csVa2QJIsS90WzPpB1eRnNtQ69Nj
89Zfwa6bbX0TXDgw1Aa28NewPY/3xWpCjI03HBQaMIncToWv3/dzNUr0bEmIuBds
wsr5Y+fy80VKnkoXG7XzGFOqmxxFwNS+UF3M1WNtQ+xcr9rK3/LLxyWFy84S9UIe
4lVOb+df91YFIJeLs28/hfTiRhvV0fWIbupGv8UhuBMho+F0dpLvra+3xksEqALu
4+AzI0j9GjqFfMzbmRBcPcT4Rl37nLmvQ+7XokrFgAYS5zp7OGylOMU3nHyvkuY=
=iL8v
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Major changes:
iwlwifi:
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
* add support for beamforming
* enable stuck queue detection for iwlmvm
* a few fixes for EBS scan
* fixes for various failure paths
* improvements for TDLS Offchannel
wil6210:
* performance tuning
* some AP features
brcm80211:
* rework some code in SDIO part of the brcmfmac driver related to
suspend/resume that were found doing stress testing
* in PCIe part scheduling of worker thread needed to be relaxed
* minor fixes and exposing firmware revision information to
user-space, ie. ethtool.
mwifiex:
* enhancements for change virtual interface handling
* remove coupling between netdev and FW supported interface
combination, now conversion from any type of supported interface
types to any other type is possible
* DFS support in AP mode
ath9k:
* fix calibration issues on some boards
* Wake-on-WLAN improvements
ath10k:
* add support for qca6174 hardware
* enable RX batching to reduce CPU load
Conflicts:
drivers/net/wireless/rtlwifi/pci.c
Conflict resolution is to get rid of the 'end' label and keep
the rest.
Signed-off-by: David S. Miller <davem@davemloft.net>
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
-----BEGIN PGP SIGNATURE-----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=wOaR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-02-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
