Back when I added -Werror in commit ba55bd7436 ("powerpc: Add
configurable -Werror for arch/powerpc") I did it by adding it to most
of the arch Makefiles.
At the time we excluded math-emu, because apparently it didn't build
cleanly. But that seems to have been fixed somewhere in the interim.
So move the -Werror addition to the top-level of the arch, this saves
us from repeating it in every Makefile and means we won't forget to
add it to any new sub-dirs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is the framework for using XIVE in a PowerVM guest. The support
is very similar to the native one in a much simpler form.
Each source is associated with an Event State Buffer (ESB). This is a
two bit state machine which is used to trigger events. The bits are
named "P" (pending) and "Q" (queued) and can be controlled by MMIO.
The Guest OS registers event (or notifications) queues on which the HW
will post event data for a target to notify.
Instead of OPAL calls, a set of Hypervisors call are used to configure
the interrupt sources and the event/notification queues of the guest:
- H_INT_GET_SOURCE_INFO
used to obtain the address of the MMIO page of the Event State
Buffer (PQ bits) entry associated with the source.
- H_INT_SET_SOURCE_CONFIG
assigns a source to a "target".
- H_INT_GET_SOURCE_CONFIG
determines to which "target" and "priority" is assigned to a source
- H_INT_GET_QUEUE_INFO
returns the address of the notification management page associated
with the specified "target" and "priority".
- H_INT_SET_QUEUE_CONFIG
sets or resets the event queue for a given "target" and "priority".
It is also used to set the notification config associated with the
queue, only unconditional notification for the moment. Reset is
performed with a queue size of 0 and queueing is disabled in that
case.
- H_INT_GET_QUEUE_CONFIG
returns the queue settings for a given "target" and "priority".
- H_INT_RESET
resets all of the partition's interrupt exploitation structures to
their initial state, losing all configuration set via the hcalls
H_INT_SET_SOURCE_CONFIG and H_INT_SET_QUEUE_CONFIG.
- H_INT_SYNC
issue a synchronisation on a source to make sure sure all
notifications have reached their queue.
As for XICS, the XIVE interface for the guest is described in the
device tree under the "interrupt-controller" node. A couple of new
properties are specific to XIVE :
- "reg"
contains the base address and size of the thread interrupt
managnement areas (TIMA), also called rings, for the User level and
for the Guest OS level. Only the Guest OS level is taken into
account today.
- "ibm,xive-eq-sizes"
the size of the event queues. One cell per size supported, contains
log2 of size, in ascending order.
- "ibm,xive-lisn-ranges"
the interrupt numbers ranges assigned to the guest. These are
allocated using a simple bitmap.
and also :
- "/ibm,plat-res-int-priorities"
contains a list of priorities that the hypervisor has reserved for
its own use.
Tested with a QEMU XIVE model for pseries and with the Power hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The XIVE interrupt controller is the new interrupt controller
found in POWER9. It supports advanced virtualization capabilities
among other things.
Currently we use a set of firmware calls that simulate the old
"XICS" interrupt controller but this is fairly inefficient.
This adds the framework for using XIVE along with a native
backend which OPAL for configuration. Later, a backend allowing
the use in a KVM or PowerVM guest will also be provided.
This disables some fast path for interrupts in KVM when XIVE is
enabled as these rely on the firmware emulation code which is no
longer available when the XIVE is used natively by Linux.
A latter patch will make KVM also directly exploit the XIVE, thus
recovering the lost performance (and more).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fixup pr_xxx("XIVE:"...), don't split pr_xxx() strings,
tweak Kconfig so XIVE_NATIVE selects XIVE and depends on POWERNV,
fix build errors when SMP=n, fold in fixes from Ben:
Don't call cpu_online() on an invalid CPU number
Fix irq target selection returning out of bounds cpu#
Extra sanity checks on cpu numbers
]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
