When network interface is made active we were not handling the error
scenarios properly to clean up rx & tx resources which might result in
a driver panic.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves an issue with map single being used to map a buffer and
then unmap page being used to unmap it. In addition it handles any error
conditions that may be detected using skb_dma_map.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI-X allocation broke after the 82599 merge on systems with more than 8
CPU cores. 82598 drops back into MSI mode, which isn't sufficient to run
full, efficient 10G line rate.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the past flow control wasn't enabled by default under the
incorrect assumption that this opened up us to a denial of
service attack. However since any switch that forwarded flow
control would be extremely msiconfigured and/or buggy, this
concern no longer out weighs the preformance gains from
having FC enabled.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priority flow control settings from the netlink layer aren't taking
effect in the base driver. The boolean pfc_mode_enable in the dcb_config
struct isn't being set, so the hardware configuration code is never
reached.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool tries to get advertised speed from phy.autoneg_advertised.
However for copper media this wasn't happening until later do to
an other fix which moved mac.ops.setup_link_speed placement in
ixgbe_link_config(). This patch will display the default advertised
speeds if it can't yet get this information from phy.autoneg_advertised.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ixgbe driver had issues when DEBUG was defined because the hw_dbg macro
was incomplete. This patch completes the code based off of the code that
already existed in the igb module.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Fix
Yinghai Lu found one system with 82575EB where, in the kernel that is
kexeced, probe igb failed with -2, the reason being that the adapter
could not be brought back from D3 by the kexec kernel, most probably
due to quirky hardware (it looks like the same behavior happened on
forcedeth).
Prevent igb from putting the adapter into D3 during shutdown except
when we going to power off the system. For this purpose, seperate
igb_shutdown() from igb_suspend() and use the appropriate PCI PM
callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code path for setting up phy loopback testing was out of date and was
setting bits it didn't need to. This change cleans up the code path and
removes some code that has no effect on teh driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the delay for copper phy init from 15ms to 100ms. This is to
address issues seen in which ethtool -t was failing in some cases on 82576
based adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue was seen on suspend in which the system reported a page fault. This
was due to the new reg_idx code being called after the queues were freed.
This update prevents any for loops from going through the queues by setting
the number of queues to 0 when they are freed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is on PCIe link trained as x2 the driver is currently reporting
link width as "unknown". The original patch provided by Myron adds the x2
link support and my changes are cosmetic to clean up the readability of the
conditional operators.
Based on work by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC Ethernet device isn't always attached to a phy. Be careful
not to dereference phy_device if it is NULL. Also eliminates an
unnecessary extra function from the ioctl path.
Reported-by: Henk Stegeman <henk.stegeman@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since not using net_device_ops gets you shunned out the cool crowd,
this patch modifies the fec_mpc52xx Ethernet driver to provide the
management hooks via a struct net_device_ops.
Reported-by: Henk Stegeman <henk.stegeman@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver triggers a BUG_ON() when allocating DMA buffers because the
arch/powerpc dma_ops aren't in the net_device's struct device. This
patch fixes the problem by using the parent of_device which does have
the correct dma_ops set.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 784544739a
(netfilter: iptables: lock free counters) forgot to disable BH
in arpt_do_table(), ipt_do_table() and ip6t_do_table()
Use rcu_read_lock_bh() instead of rcu_read_lock() cures the problem.
Reported-and-bisected-by: Roman Mindalev <r000n@r000n.net>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a 64bit value that needs to be set atomically.
This is easy and quick on all 64bit archs, and can also be done
on x86/32 with set_64bit() (uses cmpxchg8b). However other
32b archs don't have this.
I actually changed this to the current state in preparation for
mainline because the old way (using a spinlock on 32b) resulted in
unsightly #ifdefs in the code. But obviously, being correct takes
precedence.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug where a connection was unexpectedly
not on *any* list while being destroyed. It also
cleans up some code duplication and regularizes some
function names.
* Grab appropriate lock in conn_free() and explain in comment
* Ensure via locking that a conn is never not on either
a dev's list or the nodev list
* Add rds_xx_remove_conn() to match rds_xx_add_conn()
* Make rds_xx_add_conn() return void
* Rename remove_{,nodev_}conns() to
destroy_{,nodev_}conns() and unify their implementation
in a helper function
* Document lock ordering as nodev conn_lock before
dev_conn_lock
Reported-by: Yosef Etigin <yosefe@voltaire.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rs_send_drop_to() is called during socket close. If it takes
m_rs_lock without disabling interrupts, then
rds_send_remove_from_sock() can run from the rx completion
handler and thus deadlock.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Kconfig and Makefile related changes for vxge driver.
- No changes in current submission.
- Changes from previous submission -
- Incorporated the following review comments as per Bill Flink:
- Add dependancy on INET along with PCI
- Remove dependancy on INET_LRO and add GRO support.
- Made this patch as last patch as per Ben Hutchings comments.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements all ethtool related entry point functions for the driver.
- Changes in this submission -
- Removed redundant #include statements
- Changes in previous submissions -
- Removed unused statistics.
- General clean up - removed unused variables and macros.
- Incorporated following comments from Ben Hutchings
- No need to restart the interface in vxge_ethtool_sset
- Do not use #ifdef ADVERTISED_XX
- Remove unnecessart intermediate copy in vxge_ethtool_gdrvinfo
- Use strlcpy() to ensure null-termination.
- Use ethtool_op_get_tso, ethtool_op_set_tx_hw_csum instead
of redefining the same code.
- Implement get_strings_count instead of deprecated get_stats_count.
- Don't report reporting the EEPROM length as we don't supprt
get/set eeprom.
- Don't set self_test_count as we don't support any self tests.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements all the driver entry point functions.
- Definition of all module loadable paramters.
- Implementation of all driver entry point functions.
- Changes in this submission -
- Fixed compilation error when enabling debug statements
- Fixed few warnings when CONFIG_PCI_MSI is not defined
- Removed unnecessary volatile variables
- Removed compare_ether_addr as it causes unaligned memory access on
the sparc64 platform.
- Changes in previous submissions -
- As per Stephen Hemminger's comments removed the following loadable
parameters - gro, rx_& tx max_indicate_pkts, exec_mode, rx & tx
pause_enable, tx_steering_type and intr_type.
- Added Device ID definition in vxge-main.h instead of
include/linux/pci_ids.h file - Reported by David Miller
- Incorporated following review comments from Ben Hutchings
- NAPI is always enabled (no option to turn it OFF).
- Loadable parameters
rx_steering_type: This loadable option is removed.
ring_blocks: This loadable option is removed.
The driver default settings work well in most if not all cases.
Another patch to configure these parameters with ethtool will be
released in the future.
- LRO has been deprecated in favour of GRO - Bill Fink & Dave Miller's comment
- Fixed sparse warnings - Reported by Andi Kleen
- Removed unused variables
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of trafic handling related APIS.
- Interrupt Enable and disable
- Mask / Unmask Interrupt
- Traffic Interrupt handling.
- Alarm Interrupt handling.
- Changes in this submission -
- General clean up - removed redundant includes, defines and macros.
- Changes in previous submissions -
- General cleanup - removed unused functions and variables.
- Use asserts where necessary - Reported by Andi Kleen
- Fixed sparse warnings - Reported by Andi Kleen
- Use a prefix, "__vxge" in front of hw functions to make them globally
unique - Ben Hutchings
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of Initialization and configuration steps of
Neterion Inc's X3100 Series 10GbE PCIe I/O Virtualized Server Adapter.
- Device Initialization.
- Verification and setting of device config parameters.
- Allocation of Tx FIFO and Rx Ring descriptors (DTR).
- APIs to get various type of hw stats
- APIs to configure RTS (Receive Traffic Steering)
- Changes in this submission -
- Include vmalloc header without which a compilation error occured
on sparc64, ppc64 and IA64 plaforms.
- Fixed compilation warning in register_poll, write32_upper,
write32_lower and the special write64 functions on ppc64.
- General cleanup - removed redundant includes and defines.
- Changes in previous submissions -
- Add readq/writeq implementation for the driver for 32 bit systems -
reported by Dave Miller.
- Incorporated following comments from Ben Hutchings
- Start a comment with "/**" to make it a kernel-doc comment.
- Use prefix, "__vxge" in front of hw functions to make them globally
unique.
- Fixed unnecessary clearing members of *channel just before freeing
- Use backslashes only for macro definitions and not in multi-line
statements.
- Used pci_find_capability instead of redefining it.
- Used device and revision ids that are already in pdev - no need to
read them again.
- Used pci_save_state() and pci_restore_state() around resets.
- Used udelay and mdelay directly instead of wrapper.
- In __vxge_hw_device_register_poll() reset i to 0 after the
microsecond delay loop to commence the millisecond delay loop.
- Corrected spelling "sapper" - should be "swapper"
- Remove too much vertical whitespace.
- Replaced magic numbers with appropriate macros
- Incorporated following comments from Andi Kleen [andi@firstfloor.org]
- Reduced the arguments in functions or refactored them into smaller
functions.
- Allocate page sized memories used in slow path with vmalloc.
- Use asserts where necessary.
- Use macros instead of magic numbers.
- Use the pci layer code instead of defining own functions
- Remove driver wrappers such as xge_hw_device_private_set().
- Fixed sparse warnings.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Complete Register map details of Neterion Inc's X3100 Series 10GbE PCIe I/O
Virtualized Server Adapter.
- No change from previous submission.
- Changes in previous submissions -
- Incorporated following comments from Ben Hutchings
- Use original macros for endian checks
- Remove VXGE_OS_PLATFORM_* macros as they are unused.
- Converted multiple bVALX macros into single with additional
width parameter and renamed it to vxge_bVALn.
- Using __packed instead of pragma pack(1)
- Added a comment of the use of a hw swapper so driver code is
portable (does not have to change the byte order for register
access as well as dma operations) on different ENDIAN platforms.
- Using the <linux/pci_regs.h> definitions instead of redefing them.
- Using the PCI capabilities registers in <linux/pci_regs.h>
instead of redefing them.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- update to Maintainer list of S2IO 10GbE drivers (xframe/vxge).
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- vxge driver help text file.
- No change from previous submission.
- Changes in previous submissions -
Removed the performance tuning section with instructions to disable
time stamps and change sysctl settings - Reported by Dave Miller
General clean up.
- Removed tx/rx_pause, exec_mode, tx_steering_type, rx_steering_type, gro,
intr_type, rx & tx max_indicate_pkts and exec_mode loadable parameters. The
driver default settings work well in most if not all cases. Another patch
to configure these parameters with ethtool will be released in the future -
Reported by Stephen Hemminger.
- Incorporated following fixes based on comments from Ben Hutchings
Removed references to earlier kernel versions.
Removed sections that are similar for all drivers -
Load/Unload
Identifying the adapter/interface
Boot time configuration
Removed loadable parameter -
NAPI - Napi is always enabled.
rx_steering_type & ring_blocks - The driver default settings
work well in most if not all cases. Another patch to configure
these parameters with ethtool will be released in the future.
Removed ethtool support section - No need to duplicate ethtool
docs here.
Removed Known Issue on SUSE 9 - Doesn't apply when using a
current kernel.
Removed Common Problems section - These don't apply to in-tree modules.
Removed Available Downloads section - Not sure this belongs in-tree.
Removed Copyright information - This notice doesn't belong in
the kernel.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: clean up
those code pcpu_need_numa(), should be removed.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: David Miller <davem@davemloft.net>
LKML-Reference: <49D31770.9090502@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
setup_percpu_remap() is for NUMA machines yet it bailed out with
-EINVAL if pcpu_need_numa(). Fix the inverted condition.
This problem was reported by David Miller and verified by Yinhai Lu.
Reported-by: David Miller <davem@davemloft.net>
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <49D30469.8020006@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a baby-step in the direction of having finer-grained
locking than the struct_mutex. Specifically, this will enable
new debugging code to read the active list for printing out
GPU state when the GPU is wedged, (while the struct_mutex is
held, of course).
Signed-off-by: Carl Worth <cworth@cworth.org>
[anholt: indentation fix]
Signed-off-by: Eric Anholt <eric@anholt.net>
This brings SDVO TV support from 2D driver, including origin
fix f1ca56e17d0 and later fix 2fcf4fcccfe. Also fix wrong modeline
definitions for SDVO TV.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix compile error of intel_sdvo_debug_response(),
and explicit use KERN_DEBUG for printk.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Only set TV DAC in property change seems doesn't work, we have to
setup whole crtc pipe which assigned to TV alone.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: Note that this should also fix the oops at startup with new 2D]
Signed-off-by: Eric Anholt <eric@anholt.net>
If there's no real property change, don't need to set TV mode again.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: checkpatch.pl fix]
Signed-off-by: Eric Anholt <eric@anholt.net>
udelay() of 20 milliseconds really ought to just use mdelay(), that avoids
the various wrap scenarios and also is more readable
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add VGA port hotplug detection to the i915 driver. When KMS is enabled,
plugging in or removing a VGA cable from the VGA connector will
generate a uevent, which indicates to userspace that it should re-probe
outputs on this device (to determine modes, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: dropped extra PORT_HOTPLUG_STAT clear with ack from jbarnes]
Signed-off-by: Eric Anholt <eric@anholt.net>
"struct tty_driver *" lies in m->private not in v which is
SEQ_TOKEN_START which is 1 which is enough to trigger NULL dereference
next line:
BUG: unable to handle kernel NULL pointer dereference at 000000ad
IP: [<c040d689>] uart_proc_show+0xe/0x2b0
Noticed by Linus.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: guard against pre-ACPI 3 e820 code not updating %ecx
Commit 64ef895798 ("qeth: remove EDDP")
removed the qeth_core_offl.[hc] files, but ended up doing so by just
patching them to zero size, rather than removing them properly.
Actually remove the files.
Reported-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IGD device only has last 1 page used by GTT. This should match the AGP gart
code.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
drm_get_edid will store edid into raw_edid, so when freeing edid memory,
at the same time clean raw_edid pointer.
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Note that raw_edid is not currently used anywhere]
Signed-off-by: Eric Anholt <eric@anholt.net>
Impact: BIOS bug safety
For pre-ACPI 3 BIOSes, pre-initialize the end of the e820 buffer just
in case the BIOS returns an unchanged %ecx but without actually
touching the ACPI 3 extended flags field.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86/setup' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: ACPI 3, BIOS workaround for E820-probing code
x86, setup: preemptively save/restore edi and ebp around INT 15 E820
x86, setup: mark %esi as clobbered in E820 BIOS call
Indicates something is wrong with the mapping; and apparently triggers
in current kernels.
Signed-off-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes all the tiling problems with the 2d ddx. glxgears still doesn't work.
Changes:
- fix a copy&paste error in i8xx fence reg setup. It resulted in an at most a
512KB offset of the fence reg window, so was only visible sometimes.
- add tests for stride and object size constrains (also for i915 and 1965 class
hw). Userspace seems to have an of-by-one bug there, which changes the fence
size by at most 512KB due to an overflow.
- because i8xx hw is quite old (and therefore not as well-tested) I left 2 debug
WARN_ONs in the i8xx fence reg setup code to hopefully catch any further
overflows in the bit-fields. Lastly there's one small change to make the
alignment checks more consistent.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=20289
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (58 commits)
SUNRPC: Ensure IPV6_V6ONLY is set on the socket before binding to a port
NSM: Fix unaligned accesses in nsm_init_private()
NFS: Simplify logic to compare socket addresses in client.c
NFS: Start PF_INET6 callback listener only if IPv6 support is available
lockd: Start PF_INET6 listener only if IPv6 support is available
SUNRPC: Remove CONFIG_SUNRPC_REGISTER_V4
SUNRPC: rpcb_register() should handle errors silently
SUNRPC: Simplify kernel RPC service registration
SUNRPC: Simplify svc_unregister()
SUNRPC: Allow callers to pass rpcb_v4_register a NULL address
SUNRPC: rpcbind actually interprets r_owner string
SUNRPC: Clean up address type casts in rpcb_v4_register()
SUNRPC: Don't return EPROTONOSUPPORT in svc_register()'s helpers
SUNRPC: Use IPv4 loopback for registering AF_INET6 kernel RPC services
SUNRPC: Set IPV6ONLY flag on PF_INET6 RPC listener sockets
NFS: Revert creation of IPv6 listeners for lockd and NFSv4 callbacks
SUNRPC: Remove @family argument from svc_create() and svc_create_pooled()
SUNRPC: Change svc_create_xprt() to take a @family argument
SUNRPC: svc_setup_socket() gets protocol family from socket
SUNRPC: Pass a family argument to svc_register()
...
