iomem_resource is by default initialized to -1, which means 64 bits of
physical address space if 64-bit resources are enabled. However, x86
CPUs cannot address 64 bits of physical address space. Thus, we want
to cap the physical address space to what the union of all CPU can
actually address.
Without this patch, we may end up assigning inaccessible values to
uninitialized 64-bit PCI memory resources.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Martin Mares <mj@ucw.cz>
Cc: stable@kernel.org
Now that enable_iommus() will call iommu_disable() for each iommu,
the call to disable_iommus() during resume is redundant. Also, the order
for an invalidation is to invalidate device table entries first, then
domain translations.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
These registers may contain values from previous kernels. So reset them
to known values before enable the event buffer again.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The IOMMU spec states that IOMMU behavior may be undefined when the
IOMMU registers are rewritten while command or event buffer is enabled.
Disable them in IOMMU disable path.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When kexec'ing to a new kernel (for example, when crashing and launching
a kdump session), the AMD IOMMU may have cached translations. The kexec'd
kernel, during initialization, will invalidate the IOMMU device table
entries, but not the domain translations. These stale entries can cause
a device's DMA to fail, makes it rough to write a dump to disk when the
disk controller can't DMA ;-)
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
If the IOMMUs are still enabled when the kexec kernel boots access to
the disk is not possible. This is bad for tools like kdump or anything
else which wants to use PCI devices.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When the IOMMU stays enabled the BIOS may not be able to finish the
machine shutdown properly. So disable the hardware on shutdown.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
timer interrupts are excluded from being disabled during suspend. The
clock events code manages the disabling of clock events on its own
because the timer interrupt needs to be functional before the resume
code reenables the device interrupts.
The hpet per cpu timers request their interrupt without setting the
IRQF_TIMER flag so suspend_device_irqs() disables them as well which
results in a fatal resume failure on the boot CPU.
Adding IRQF_TIMER to the interupt flags when requesting the hpet per
cpu timer interrupts solves the problem.
Reported-by: Benjamin S. <sbenni@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Benjamin S. <sbenni@gmx.de>
Cc: stable@kernel.org
_sdata is a common symbol defined by many architectures and made
available to the kernel via asm-generic/sections.h. Kmemleak uses this
symbol when scanning the data sections.
[ Impact: add new global symbol ]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
LKML-Reference: <20090511122105.26556.96593.stgit@pc1117.cambridge.arm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On a system where system memory (according e820) is not covered by
mtrr, mtrr_trim_memory converts a portion of memory to reserved, but
bootloader has already put the initrd in that range.
Thus, we need to have 64bit to use relocate_initrd too.
[ Impact: fix using initrd when mtrr_trim_memory happen ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
* 'perfcounters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (574 commits)
perf_counter: Turn off by default
perf_counter: Add counter->id to the throttle event
perf_counter: Better align code
perf_counter: Rename L2 to LL cache
perf_counter: Standardize event names
perf_counter: Rename enums
perf_counter tools: Clean up u64 usage
perf_counter: Rename perf_counter_limit sysctl
perf_counter: More paranoia settings
perf_counter: powerpc: Implement generalized cache events for POWER processors
perf_counters: powerpc: Add support for POWER7 processors
perf_counter: Accurate period data
perf_counter: Introduce struct for sample data
perf_counter tools: Normalize data using per sample period data
perf_counter: Annotate exit ctx recursion
perf_counter tools: Propagate signals properly
perf_counter tools: Small frequency related fixes
perf_counter: More aggressive frequency adjustment
perf_counter/x86: Fix the model number of Intel Core2 processors
perf_counter, x86: Correct some event and umask values for Intel processors
...
* 'topic/slab/earlyboot' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
vgacon: use slab allocator instead of the bootmem allocator
irq: use kcalloc() instead of the bootmem allocator
sched: use slab in cpupri_init()
sched: use alloc_cpumask_var() instead of alloc_bootmem_cpumask_var()
memcg: don't use bootmem allocator in setup code
irq/cpumask: make memoryless node zero happy
x86: remove some alloc_bootmem_cpumask_var calling
vt: use kzalloc() instead of the bootmem allocator
sched: use kzalloc() instead of the bootmem allocator
init: introduce mm_init()
vmalloc: use kzalloc() instead of alloc_bootmem()
slab: setup allocators earlier in the boot sequence
bootmem: fix slab fallback on numa
bootmem: use slab if bootmem is no longer available
* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (138 commits)
KVM: Prevent overflow in largepages calculation
KVM: Disable large pages on misaligned memory slots
KVM: Add VT-x machine check support
KVM: VMX: Rename rmode.active to rmode.vm86_active
KVM: Move "exit due to NMI" handling into vmx_complete_interrupts()
KVM: Disable CR8 intercept if tpr patching is active
KVM: Do not migrate pending software interrupts.
KVM: inject NMI after IRET from a previous NMI, not before.
KVM: Always request IRQ/NMI window if an interrupt is pending
KVM: Do not re-execute INTn instruction.
KVM: skip_emulated_instruction() decode instruction if size is not known
KVM: Remove irq_pending bitmap
KVM: Do not allow interrupt injection from userspace if there is a pending event.
KVM: Unprotect a page if #PF happens during NMI injection.
KVM: s390: Verify memory in kvm run
KVM: s390: Sanity check on validity intercept
KVM: s390: Unlink vcpu on destroy - v2
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock
KVM: s390: use hrtimer for clock wakeup from idle - v2
KVM: s390: Fix memory slot versus run - v3
...
Don't hardcode to node zero for early boot IRQ setup memory allocations.
[ penberg@cs.helsinki.fi: minor cleanups ]
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Now that we set up the slab allocator earlier, we can get rid of some
alloc_bootmem_cpumask_var() calls in boot code.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
The top (fastest) and last level (biggest) caches are the most
interesting ones, performance wise.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
[ Fixed the Nehalem LL table to LLC Reference/Miss events ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pure renames only, to PERF_COUNT_HW_* and PERF_COUNT_SW_*.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
We currently log hw.sample_period for PERF_SAMPLE_PERIOD, however this is
incorrect. When we adjust the period, it will only take effect the next
cycle but report it for the current cycle. So when we adjust the period
for every cycle, we're always wrong.
Solve this by keeping track of the last_period.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For easy extension of the sample data, put it in a structure.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (61 commits)
amd-iommu: remove unnecessary "AMD IOMMU: " prefix
amd-iommu: detach device explicitly before attaching it to a new domain
amd-iommu: remove BUS_NOTIFY_BOUND_DRIVER handling
dma-debug: simplify logic in driver_filter()
dma-debug: disable/enable irqs only once in device_dma_allocations
dma-debug: use pr_* instead of printk(KERN_* ...)
dma-debug: code style fixes
dma-debug: comment style fixes
dma-debug: change hash_bucket_find from first-fit to best-fit
x86: enable GART-IOMMU only after setting up protection methods
amd_iommu: fix lock imbalance
dma-debug: add documentation for the driver filter
dma-debug: add dma_debug_driver kernel command line
dma-debug: add debugfs file for driver filter
dma-debug: add variables and checks for driver filter
dma-debug: fix debug_dma_sync_sg_for_cpu and debug_dma_sync_sg_for_device
dma-debug: use sg_dma_len accessor
dma-debug: use sg_dma_address accessor instead of using dma_address directly
amd-iommu: don't free dma adresses below 512MB with CONFIG_IOMMU_STRESS
amd-iommu: don't preallocate page tables with CONFIG_IOMMU_STRESS
...
* 'x86-xen-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (42 commits)
xen: cache cr0 value to avoid trap'n'emulate for read_cr0
xen/x86-64: clean up warnings about IST-using traps
xen/x86-64: fix breakpoints and hardware watchpoints
xen: reserve Xen start_info rather than e820 reserving
xen: add FIX_TEXT_POKE to fixmap
lguest: update lazy mmu changes to match lguest's use of kvm hypercalls
xen: honour VCPU availability on boot
xen: add "capabilities" file
xen: drop kexec bits from /sys/hypervisor since kexec isn't implemented yet
xen/sys/hypervisor: change writable_pt to features
xen: add /sys/hypervisor support
xen/xenbus: export xenbus_dev_changed
xen: use device model for suspending xenbus devices
xen: remove suspend_cancel hook
xen/dev-evtchn: clean up locking in evtchn
xen: export ioctl headers to userspace
xen: add /dev/xen/evtchn driver
xen: add irq_from_evtchn
xen: clean up gate trap/interrupt constants
xen: set _PAGE_NX in __supported_pte_mask before pagetable construction
...
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clear TS in irq_ts_save() when in an atomic section
x86: Detect use of extended APIC ID for AMD CPUs
x86: memtest: remove 64-bit division
x86, UV: Fix macros for multiple coherency domains
x86: Fix non-lazy GS handling in sys_vm86()
x86: Add quirk for reboot stalls on a Dell Optiplex 360
x86: Fix UV BAU activation descriptor init
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (22 commits)
x86: fix system without memory on node0
x86, mm: Fix node_possible_map logic
mm, x86: remove MEMORY_HOTPLUG_RESERVE related code
x86: make sparse mem work in non-NUMA mode
x86: process.c, remove useless headers
x86: merge process.c a bit
x86: use sparse_memory_present_with_active_regions() on UMA
x86: unify 64-bit UMA and NUMA paging_init()
x86: Allow 1MB of slack between the e820 map and SRAT, not 4GB
x86: Sanity check the e820 against the SRAT table using e820 map only
x86: clean up and and print out initial max_pfn_mapped
x86/pci: remove rounding quirk from e820_setup_gap()
x86, e820, pci: reserve extra free space near end of RAM
x86: fix typo in address space documentation
x86: 46 bit physical address support on 64 bits
x86, mm: fault.c, use printk_once() in is_errata93()
x86: move per-cpu mmu_gathers to mm/init.c
x86: move max_pfn_mapped and max_low_pfn_mapped to setup.c
x86: unify noexec handling
x86: remove (null) in /sys kernel_page_tables
...
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, microcode: Simplify vfree() use
x86: microcode: use smp_call_function_single instead of set_cpus_allowed, cleanup of synchronization logic
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_debug: Remove model information to reduce encoding-decoding
x86: fixup numa_node information for AMD CPU northbridge functions
x86: k8 convert node_to_k8_nb_misc() from a macro to an inline function
x86: cacheinfo: complete L2/L3 Cache and TLB associativity field definitions
x86/docs: add description for cache_disable sysfs interface
x86: cacheinfo: disable L3 ECC scrubbing when L3 cache index is disabled
x86: cacheinfo: replace sysfs interface for cache_disable feature
x86: cacheinfo: use cached K8 NB_MISC devices instead of scanning for it
x86: cacheinfo: correct return value when cache_disable feature is not active
x86: cacheinfo: use L3 cache index disable feature only for CPUs that support it
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, nmi: Use predefined numbers instead of hardcoded one
x86: asm/processor.h: remove double declaration
x86, mtrr: replace MTRRdefType_MSR with msr-index's MSR_MTRRdefType
x86, mtrr: replace MTRRfix4K_C0000_MSR with msr-index's MSR_MTRRfix4K_C0000
x86, mtrr: remove mtrr MSRs double declaration
x86, mtrr: replace MTRRfix16K_80000_MSR with msr-index's MSR_MTRRfix16K_80000
x86, mtrr: replace MTRRfix64K_00000_MSR with msr-index's MSR_MTRRfix64K_00000
x86, mtrr: replace MTRRcap_MSR with msr-index's MSR_MTRRcap
x86: mce: remove duplicated #include
x86: msr-index.h remove duplicate MSR C001_0015 declaration
x86: clean up arch/x86/kernel/tsc_sync.c a bit
x86: use symbolic name for VM86_SIGNAL when used as vm86 default return
x86: added 'ifndef _ASM_X86_IOMAP_H' to iomap.h
x86: avoid multiple declaration of kstack_depth_to_print
x86: vdso/vma.c declare vdso_enabled and arch_setup_additional_pages before they get used
x86: clean up declarations and variables
x86: apic/x2apic_cluster.c x86_cpu_to_logical_apicid should be static
x86 early quirks: eliminate unused function
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, 64-bit: ifdef out struct thread_struct::ip
x86, 32-bit: ifdef out struct thread_struct::fs
x86: clean up alternative.h
* 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (46 commits)
x86, boot: add new generated files to the appropriate .gitignore files
x86, boot: correct the calculation of ZO_INIT_SIZE
x86-64: align __PHYSICAL_START, remove __KERNEL_ALIGN
x86, boot: correct sanity checks in boot/compressed/misc.c
x86: add extension fields for bootloader type and version
x86, defconfig: update kernel position parameters
x86, defconfig: update to current, no material changes
x86: make CONFIG_RELOCATABLE the default
x86: default CONFIG_PHYSICAL_START and CONFIG_PHYSICAL_ALIGN to 16 MB
x86: document new bzImage fields
x86, boot: make kernel_alignment adjustable; new bzImage fields
x86, boot: remove dead code from boot/compressed/head_*.S
x86, boot: use LOAD_PHYSICAL_ADDR on 64 bits
x86, boot: make symbols from the main vmlinux available
x86, boot: determine compressed code offset at compile time
x86, boot: use appropriate rep string for move and clear
x86, boot: zero EFLAGS on 32 bits
x86, boot: set up the decompression stack as early as possible
x86, boot: straighten out ranges to copy/zero in compressed/head*.S
x86, boot: stylistic cleanups for boot/compressed/head_64.S
...
Fixed trivial conflict in arch/x86/configs/x86_64_defconfig manually
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (76 commits)
x86, apic: Fix dummy apic read operation together with broken MP handling
x86, apic: Restore irqs on fail paths
x86: Print real IOAPIC version for x86-64
x86: enable_update_mptable should be a macro
sparseirq: Allow early irq_desc allocation
x86, io-apic: Don't mark pin_programmed early
x86, irq: don't call mp_config_acpi_gsi() if update_mptable is not enabled
x86, irq: update_mptable needs pci_routeirq
x86: don't call read_apic_id if !cpu_has_apic
x86, apic: introduce io_apic_irq_attr
x86/pci: add 4 more return parameters to IO_APIC_get_PCI_irq_vector(), fix
x86: read apic ID in the !acpi_lapic case
x86: apic: Fixmap apic address even if apic disabled
x86: display extended apic registers with print_local_APIC and cpu_debug code
x86: read apic ID in the !acpi_lapic case
x86: clean up and fix setup_clear/force_cpu_cap handling
x86: apic: Check rev 3 fadt correctly for physical_apic bit
x86/pci: update pirq_enable_irq() to setup io apic routing
x86/acpi: move setup io apic routing out of CONFIG_ACPI scope
x86/pci: add 4 more return parameters to IO_APIC_get_PCI_irq_vector()
...
The e_powersaver driver for VIA's C7 CPU's needs to be marked as
DANGEROUS as it configures the CPU to power states that are out
of specification.
According to Centaur, all systems with C7 and Nano CPU's support
the ACPI p-state method. Thus, the acpi-cpufreq driver should
be used instead.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The VIA/Centaur C7, C7-M and Nano CPU's all support ACPI based cpu p-states
using a MSR interface. The Linux driver just never made use of it, since in
addition to the check for the EST flag it also checked if the vendor is Intel.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
[ Removed the vendor checks entirely - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also employ the overflow handler to adjust the frequency, this results
in a stable frequency in about 40~50 samples, instead of that many ticks.
This also means we can start sampling at a sample period of 1 without
running head-first into the throttle.
It relies on sched_clock() to accurately measure the time difference
between the overflow NMIs.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the model number of Intel Core2 processors according to the
documentation: Intel Processor Identification with the CPUID
Instruction: http://www.intel.com/support/processors/sb/cs-009861.htm
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Also-Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <20090610090612.GA26580@ywang-moblin2.bj.intel.com>
[ Added two more model numbers suggested by Arnd Bergmann ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
VT-x needs an explicit MC vector intercept to handle machine checks in the
hyper visor.
It also has a special option to catch machine checks that happen
during VT entry.
Do these interceptions and forward them to the Linux machine check
handler. Make it always look like user space is interrupted because
the machine check handler treats kernel/user space differently.
Thanks to Jiang Yunhong for help and testing.
Cc: stable@kernel.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM uses a function call IPI to cause the exit of a guest running on a
physical cpu. For virtual interrupt notification there is no need to
wait on IPI receival, or to execute any function.
This is exactly what the reschedule IPI does, without the overhead
of function IPI. So use it instead of smp_call_function_single in
kvm_vcpu_kick.
Also change the "guest_mode" variable to a bit in vcpu->requests, and
use that to collapse multiple IPI's that would be issued between the
first one and zeroing of guest mode.
This allows kvm_vcpu_kick to called with interrupts disabled.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Skip the test which checks if the PIT is properly routed when
using the IOAPIC, aimed at buggy hardware.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Correct some event and UMASK values according to Intel SDM,
in the Nehalem and Atom tables.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <20090609131553.GA12489@ywang-moblin2.bj.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Booting a 32-bit kernel on Magny-Cours results in the following panic:
...
Using APIC driver default
...
Overriding APIC driver with bigsmp
...
Getting VERSION: 80050010
Getting VERSION: 80050010
Getting ID: 10000000
Getting ID: ef000000
Getting LVT0: 700
Getting LVT1: 10000
Kernel panic - not syncing: Boot APIC ID in local APIC unexpected (16 vs 0)
Pid: 1, comm: swapper Not tainted 2.6.30-rcX #2
Call Trace:
[<c05194da>] ? panic+0x38/0xd3
[<c0743102>] ? native_smp_prepare_cpus+0x259/0x31f
[<c073b19d>] ? kernel_init+0x3e/0x141
[<c073b15f>] ? kernel_init+0x0/0x141
[<c020325f>] ? kernel_thread_helper+0x7/0x10
The reason is that default_get_apic_id handled extension of local APIC
ID field just in case of XAPIC.
Thus for this AMD CPU, default_get_apic_id() returns 0 and
bigsmp_get_apic_id() returns 16 which leads to the respective kernel
panic.
This patch introduces a Linux specific feature flag to indicate
support for extended APIC id (8 bits instead of 4 bits width) and sets
the flag on AMD CPUs if applicable.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: <stable@kernel.org>
LKML-Reference: <20090608135509.GA12431@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
These are defined as static cpumask_var_t so if MAXSMP is not used,
they are cleared already. Avoid surprises when MAXSMP is enabled.
Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
That prefix is already included in the DUMP_printk macro. So there is no
need to repeat it in the format string.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This fixes a bug with a device that could not be assigned to a KVM guest
because it is still assigned to a dma_ops protection domain.
[chrisw: simply remove WARN_ON(), will always fire since dev->driver
will be pci-sub]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Handling this event causes device assignment in KVM to fail because the
device gets re-attached as soon as the pci-stub registers as the driver
for the device.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
