During IPsec performance testing, we see bad ICMP checksum. The error packet
has duplicated ESP trailer due to double validate_xmit_xfrm calls. The first call
is from ip_output, but the packet cannot be sent because
netif_xmit_frozen_or_stopped is true and the packet gets dev_requeue_skb. The second
call is from NET_TX softirq. However after the first call, the packet already
has the ESP trailer.
Fix by marking the skb with XFRM_XMIT bit after the packet is handled by
validate_xmit_xfrm to avoid duplicate ESP trailer insertion.
Fixes: f6e27114a6 ("net: Add a xfrm validate function to validate_xmit_skb")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXtYhfgAKCRCRxhvAZXjc
oghSAP9uVX3vxYtEtNvu9WtEn1uYZcSKZoF1YrcgY7UfSmna0gEAruzyZcai4CJL
WKv+4aRq2oYk+hsqZDycAxIsEgWvNg8=
=ZWj3
-----END PGP SIGNATURE-----
Merge tag 'threads-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull thread updates from Christian Brauner:
"We have been discussing using pidfds to attach to namespaces for quite
a while and the patches have in one form or another already existed
for about a year. But I wanted to wait to see how the general api
would be received and adopted.
This contains the changes to make it possible to use pidfds to attach
to the namespaces of a process, i.e. they can be passed as the first
argument to the setns() syscall.
When only a single namespace type is specified the semantics are
equivalent to passing an nsfd. That means setns(nsfd, CLONE_NEWNET)
equals setns(pidfd, CLONE_NEWNET).
However, when a pidfd is passed, multiple namespace flags can be
specified in the second setns() argument and setns() will attach the
caller to all the specified namespaces all at once or to none of them.
Specifying 0 is not valid together with a pidfd. Here are just two
obvious examples:
setns(pidfd, CLONE_NEWPID | CLONE_NEWNS | CLONE_NEWNET);
setns(pidfd, CLONE_NEWUSER);
Allowing to also attach subsets of namespaces supports various
use-cases where callers setns to a subset of namespaces to retain
privilege, perform an action and then re-attach another subset of
namespaces.
Apart from significantly reducing the number of syscalls needed to
attach to all currently supported namespaces (eight "open+setns"
sequences vs just a single "setns()"), this also allows atomic setns
to a set of namespaces, i.e. either attaching to all namespaces
succeeds or we fail without having changed anything.
This is centered around a new internal struct nsset which holds all
information necessary for a task to switch to a new set of namespaces
atomically. Fwiw, with this change a pidfd becomes the only token
needed to interact with a container. I'm expecting this to be
picked-up by util-linux for nsenter rather soon.
Associated with this change is a shiny new test-suite dedicated to
setns() (for pidfds and nsfds alike)"
* tag 'threads-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
selftests/pidfd: add pidfd setns tests
nsproxy: attach to namespaces via pidfds
nsproxy: add struct nsset
-----BEGIN PGP SIGNATURE-----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=iLfC
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20200601' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"Summary of the significant patches:
- Record information about binds/unbinds to the audit multicast
socket. This helps identify which processes have/had access to the
information in the audit stream.
- Cleanup and add some additional information to the netfilter
configuration events collected by audit.
- Fix some of the audit error handling code so we don't leak network
namespace references"
* tag 'audit-pr-20200601' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: add subj creds to NETFILTER_CFG record to
audit: Replace zero-length array with flexible-array
audit: make symbol 'audit_nfcfgs' static
netfilter: add audit table unregister actions
audit: tidy and extend netfilter_cfg x_tables
audit: log audit netlink multicast bind and unbind
audit: fix a net reference leak in audit_list_rules_send()
audit: fix a net reference leak in audit_send_reply()
This reverts commit 441870ee42.
Like the previous patch in this series, we revert the above commit that
causes similar issues with the 'aead' object.
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit de05842076.
There is no actual tipc_node refcnt leak as stated in the above commit.
The refcnt is hold carefully for the case of an asynchronous decryption
(i.e. -EINPROGRESS/-EBUSY and skb = NULL is returned), so that the node
object cannot be freed in the meantime. The counter will be re-balanced
when the operation's callback arrives with the decrypted buffer if any.
In other cases, e.g. a synchronous crypto the counter will be decreased
immediately when it is done.
Now with that commit, a kernel panic will occur when there is no node
found (i.e. n = NULL) in the 'tipc_rcv()' or a premature release of the
node object.
This commit solves the issues by reverting the said commit, but keeping
one valid case that the 'skb_linearize()' is failed.
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Tested-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bpf_csum_level() helper which BPF programs can use in combination
with bpf_skb_adjust_room() when they pass in BPF_F_ADJ_ROOM_NO_CSUM_RESET
flag to the latter to avoid falling back to CHECKSUM_NONE.
The bpf_csum_level() allows to adjust CHECKSUM_UNNECESSARY skb->csum_levels
via BPF_CSUM_LEVEL_{INC,DEC} which calls __skb_{incr,decr}_checksum_unnecessary()
on the skb. The helper also allows a BPF_CSUM_LEVEL_RESET which sets the skb's
csum to CHECKSUM_NONE as well as a BPF_CSUM_LEVEL_QUERY to just return the
current level. Without this helper, there is no way to otherwise adjust the
skb->csum_level. I did not add an extra dummy flags as there is plenty of free
bitspace in level argument itself iff ever needed in future.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Alan Maguire <alan.maguire@oracle.com>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/279ae3717cb3d03c0ffeb511493c93c450a01e1a.1591108731.git.daniel@iogearbox.net
Lorenz recently reported:
In our TC classifier cls_redirect [0], we use the following sequence of
helper calls to decapsulate a GUE (basically IP + UDP + custom header)
encapsulated packet:
bpf_skb_adjust_room(skb, -encap_len, BPF_ADJ_ROOM_MAC, BPF_F_ADJ_ROOM_FIXED_GSO)
bpf_redirect(skb->ifindex, BPF_F_INGRESS)
It seems like some checksums of the inner headers are not validated in
this case. For example, a TCP SYN packet with invalid TCP checksum is
still accepted by the network stack and elicits a SYN ACK. [...]
That is, we receive the following packet from the driver:
| ETH | IP | UDP | GUE | IP | TCP |
skb->ip_summed == CHECKSUM_UNNECESSARY
ip_summed is CHECKSUM_UNNECESSARY because our NICs do rx checksum offloading.
On this packet we run skb_adjust_room_mac(-encap_len), and get the following:
| ETH | IP | TCP |
skb->ip_summed == CHECKSUM_UNNECESSARY
Note that ip_summed is still CHECKSUM_UNNECESSARY. After bpf_redirect()'ing
into the ingress, we end up in tcp_v4_rcv(). There, skb_checksum_init() is
turned into a no-op due to CHECKSUM_UNNECESSARY.
The bpf_skb_adjust_room() helper is not aware of protocol specifics. Internally,
it handles the CHECKSUM_COMPLETE case via skb_postpull_rcsum(), but that does
not cover CHECKSUM_UNNECESSARY. In this case skb->csum_level of the original
skb prior to bpf_skb_adjust_room() call was 0, that is, covering UDP. Right now
there is no way to adjust the skb->csum_level. NICs that have checksum offload
disabled (CHECKSUM_NONE) or that support CHECKSUM_COMPLETE are not affected.
Use a safe default for CHECKSUM_UNNECESSARY by resetting to CHECKSUM_NONE and
add a flag to the helper called BPF_F_ADJ_ROOM_NO_CSUM_RESET that allows users
from opting out. Opting out is useful for the case where we don't remove/add
full protocol headers, or for the case where a user wants to adjust the csum
level manually e.g. through bpf_csum_level() helper that is added in subsequent
patch.
The bpf_skb_proto_{4_to_6,6_to_4}() for NAT64/46 translation from the BPF
bpf_skb_change_proto() helper uses bpf_skb_net_hdr_{push,pop}() pair internally
as well but doesn't change layers, only transitions between v4 to v6 and vice
versa, therefore no adoption is required there.
[0] https://lore.kernel.org/bpf/20200424185556.7358-1-lmb@cloudflare.com/
Fixes: 2be7e212d5 ("bpf: add bpf_skb_adjust_room helper")
Reported-by: Lorenz Bauer <lmb@cloudflare.com>
Reported-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Alan Maguire <alan.maguire@oracle.com>
Link: https://lore.kernel.org/bpf/CACAyw9-uU_52esMd1JjuA80fRPHJv5vsSg8GnfW3t_qDU4aVKQ@mail.gmail.com/
Link: https://lore.kernel.org/bpf/11a90472e7cce83e76ddbfce81fdfce7bfc68808.1591108731.git.daniel@iogearbox.net
Switch all callers to map_kernel_range, which symmetric to the unmap side
(as well as the _noflush versions).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Gao Xiang <xiang@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-17-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-06-01
The following pull-request contains BPF updates for your *net-next* tree.
We've added 55 non-merge commits during the last 1 day(s) which contain
a total of 91 files changed, 4986 insertions(+), 463 deletions(-).
The main changes are:
1) Add rx_queue_mapping to bpf_sock from Amritha.
2) Add BPF ring buffer, from Andrii.
3) Attach and run programs through devmap, from David.
4) Allow SO_BINDTODEVICE opt in bpf_setsockopt, from Ferenc.
5) link based flow_dissector, from Jakub.
6) Use tracing helpers for lsm programs, from Jiri.
7) Several sk_msg fixes and extensions, from John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends support to IPv6 for Inline TLS server.
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
v1->v2:
- cc'd tcp folks.
v2->v3:
- changed EXPORT_SYMBOL() to EXPORT_SYMBOL_GPL()
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket option IPV6_ADDRFORM supports UDP/UDPLITE and TCP at present.
Previously the checking logic looks like:
if (sk->sk_protocol == IPPROTO_UDP || sk->sk_protocol == IPPROTO_UDPLITE)
do_some_check;
else if (sk->sk_protocol != IPPROTO_TCP)
break;
After commit b6f6118901 ("ipv6: restrict IPV6_ADDRFORM operation"), TCP
was blocked as the logic changed to:
if (sk->sk_protocol == IPPROTO_UDP || sk->sk_protocol == IPPROTO_UDPLITE)
do_some_check;
else if (sk->sk_protocol == IPPROTO_TCP)
do_some_check;
break;
else
break;
Then after commit 82c9ae4408 ("ipv6: fix restrict IPV6_ADDRFORM operation")
UDP/UDPLITE were blocked as the logic changed to:
if (sk->sk_protocol == IPPROTO_UDP || sk->sk_protocol == IPPROTO_UDPLITE)
do_some_check;
if (sk->sk_protocol == IPPROTO_TCP)
do_some_check;
if (sk->sk_protocol != IPPROTO_TCP)
break;
Fix it by using Eric's code and simply remove the break in TCP check, which
looks like:
if (sk->sk_protocol == IPPROTO_UDP || sk->sk_protocol == IPPROTO_UDPLITE)
do_some_check;
else if (sk->sk_protocol == IPPROTO_TCP)
do_some_check;
else
break;
Fixes: 82c9ae4408 ("ipv6: fix restrict IPV6_ADDRFORM operation")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_sendstream() may send zero length packet, then tipc_msg_append()
do not alloc skb, skb_peek_tail() will get NULL, msg_set_ack_required
will trigger NULL pointer dereference.
Reported-by: syzbot+8eac6d030e7807c21d32@syzkaller.appspotmail.com
Fixes: 0a3e060f34 ("tipc: add test for Nagle algorithm effectiveness")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move functions to manage BPF programs attached to netns that are not
specific to flow dissector to a dedicated module named
bpf/net_namespace.c.
The set of functions will grow with the addition of bpf_link support for
netns attached programs. This patch prepares ground by creating a place
for it.
This is a code move with no functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-4-jakub@cloudflare.com
In order to:
(1) attach more than one BPF program type to netns, or
(2) support attaching BPF programs to netns with bpf_link, or
(3) support multi-prog attach points for netns
we will need to keep more state per netns than a single pointer like we
have now for BPF flow dissector program.
Prepare for the above by extracting netns_bpf that is part of struct net,
for storing all state related to BPF programs attached to netns.
Turn flow dissector callbacks for querying/attaching/detaching a program
into generic ones that operate on netns_bpf. Next patch will move the
generic callbacks into their own module.
This is similar to how it is organized for cgroup with cgroup_bpf.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-3-jakub@cloudflare.com
Split out the part of attach callback that happens with attach/detach lock
acquired. This structures the prog attach callback in a way that opens up
doors for moving the locking out of flow_dissector and into generic
callbacks for attaching/detaching progs to netns in subsequent patches.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-2-jakub@cloudflare.com
The sock_bindtoindex intended for kernel wide usage however
it will lock the socket regardless of the context. This modification
relax this behavior optionally: locking the socket will be optional
by calling the sock_bindtoindex with lock_sk = true.
The modification applied to all users of the sock_bindtoindex.
Signed-off-by: Ferenc Fejes <fejes@inf.elte.hu>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/bee6355da40d9e991b2f2d12b67d55ebb5f5b207.1590871065.git.fejes@inf.elte.hu
KTLS uses a stream parser to collect TLS messages and send them to
the upper layer tls receive handler. This ensures the tls receiver
has a full TLS header to parse when it is run. However, when a
socket has BPF_SK_SKB_STREAM_VERDICT program attached before KTLS
is enabled we end up with two stream parsers running on the same
socket.
The result is both try to run on the same socket. First the KTLS
stream parser runs and calls read_sock() which will tcp_read_sock
which in turn calls tcp_rcv_skb(). This dequeues the skb from the
sk_receive_queue. When this is done KTLS code then data_ready()
callback which because we stacked KTLS on top of the bpf stream
verdict program has been replaced with sk_psock_start_strp(). This
will in turn kick the stream parser again and eventually do the
same thing KTLS did above calling into tcp_rcv_skb() and dequeuing
a skb from the sk_receive_queue.
At this point the data stream is broke. Part of the stream was
handled by the KTLS side some other bytes may have been handled
by the BPF side. Generally this results in either missing data
or more likely a "Bad Message" complaint from the kTLS receive
handler as the BPF program steals some bytes meant to be in a
TLS header and/or the TLS header length is no longer correct.
We've already broke the idealized model where we can stack ULPs
in any order with generic callbacks on the TX side to handle this.
So in this patch we do the same thing but for RX side. We add
a sk_psock_strp_enabled() helper so TLS can learn a BPF verdict
program is running and add a tls_sw_has_ctx_rx() helper so BPF
side can learn there is a TLS ULP on the socket.
Then on BPF side we omit calling our stream parser to avoid
breaking the data stream for the KTLS receiver. Then on the
KTLS side we call BPF_SK_SKB_STREAM_VERDICT once the KTLS
receiver is done with the packet but before it posts the
msg to userspace. This gives us symmetry between the TX and
RX halfs and IMO makes it usable again. On the TX side we
process packets in this order BPF -> TLS -> TCP and on
the receive side in the reverse order TCP -> TLS -> BPF.
Discovered while testing OpenSSL 3.0 Alpha2.0 release.
Fixes: d829e9c411 ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/159079361946.5745.605854335665044485.stgit@john-Precision-5820-Tower
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We will need this block of code called from tls context shortly
lets refactor the redirect logic so its easy to use. This also
cleans up the switch stmt so we have fewer fallthrough cases.
No logic changes are intended.
Fixes: d829e9c411 ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/159079360110.5745.7024009076049029819.stgit@john-Precision-5820-Tower
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add xdp_txq_info as the Tx counterpart to xdp_rxq_info. At the
moment only the device is added. Other fields (queue_index)
can be added as use cases arise.
>From a UAPI perspective, add egress_ifindex to xdp context for
bpf programs to see the Tx device.
Update the verifier to only allow accesses to egress_ifindex by
XDP programs with BPF_XDP_DEVMAP expected attach type.
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200529220716.75383-4-dsahern@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add BPF_XDP_DEVMAP attach type for use with programs associated with a
DEVMAP entry.
Allow DEVMAPs to associate a program with a device entry by adding
a bpf_prog.fd to 'struct bpf_devmap_val'. Values read show the program
id, so the fd and id are a union. bpf programs can get access to the
struct via vmlinux.h.
The program associated with the fd must have type XDP with expected
attach type BPF_XDP_DEVMAP. When a program is associated with a device
index, the program is run on an XDP_REDIRECT and before the buffer is
added to the per-cpu queue. At this point rxq data is still valid; the
next patch adds tx device information allowing the prorgam to see both
ingress and egress device indices.
XDP generic is skb based and XDP programs do not work with skb's. Block
the use case by walking maps used by a program that is to be attached
via xdpgeneric and fail if any of them are DEVMAP / DEVMAP_HASH with
Block attach of BPF_XDP_DEVMAP programs to devices.
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200529220716.75383-3-dsahern@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add "rx_queue_mapping" to bpf_sock. This gives read access for the
existing field (sk_rx_queue_mapping) of struct sock from bpf_sock.
Semantics for the bpf_sock rx_queue_mapping access are similar to
sk_rx_queue_get(), i.e the value NO_QUEUE_MAPPING is not allowed
and -1 is returned in that case. This is useful for transmit queue
selection based on the received queue index which is cached in the
socket in the receive path.
v3: Addressed review comments to add usecase in patch description,
and fixed default value for rx_queue_mapping.
v2: fixed build error for CONFIG_XPS wrapping, reported by
kbuild test robot <lkp@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add these generic helpers that may be useful to use from sk_msg programs.
The helpers do not depend on ctx so we can simply add them here,
BPF_FUNC_perf_event_output
BPF_FUNC_get_current_uid_gid
BPF_FUNC_get_current_pid_tgid
BPF_FUNC_get_current_cgroup_id
BPF_FUNC_get_current_ancestor_cgroup_id
BPF_FUNC_get_cgroup_classid
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/159033903373.12355.15489763099696629346.stgit@john-Precision-5820-Tower
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Compiling with W=1 gives the following warning:
net/sched/cls_flower.c:731:1: warning: ‘mpls_opts_policy’ defined but not used [-Wunused-const-variable=]
The TCA_FLOWER_KEY_MPLS_OPTS contains a list of
TCA_FLOWER_KEY_MPLS_OPTS_LSE. Therefore, the attributes all have the
same type and we can't parse the list with nla_parse*() and have the
attributes validated automatically using an nla_policy.
fl_set_key_mpls_opts() properly verifies that all attributes in the
list are TCA_FLOWER_KEY_MPLS_OPTS_LSE. Then fl_set_key_mpls_lse()
uses nla_parse_nested() on all these attributes, thus verifying that
they have the NLA_F_NESTED flag. So we can safely drop the
mpls_opts_policy.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto updates from Herbert Xu:
"API:
- Introduce crypto_shash_tfm_digest() and use it wherever possible.
- Fix use-after-free and race in crypto_spawn_alg.
- Add support for parallel and batch requests to crypto_engine.
Algorithms:
- Update jitter RNG for SP800-90B compliance.
- Always use jitter RNG as seed in drbg.
Drivers:
- Add Arm CryptoCell driver cctrng.
- Add support for SEV-ES to the PSP driver in ccp"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (114 commits)
crypto: hisilicon - fix driver compatibility issue with different versions of devices
crypto: engine - do not requeue in case of fatal error
crypto: cavium/nitrox - Fix a typo in a comment
crypto: hisilicon/qm - change debugfs file name from qm_regs to regs
crypto: hisilicon/qm - add DebugFS for xQC and xQE dump
crypto: hisilicon/zip - add debugfs for Hisilicon ZIP
crypto: hisilicon/hpre - add debugfs for Hisilicon HPRE
crypto: hisilicon/sec2 - add debugfs for Hisilicon SEC
crypto: hisilicon/qm - add debugfs to the QM state machine
crypto: hisilicon/qm - add debugfs for QM
crypto: stm32/crc32 - protect from concurrent accesses
crypto: stm32/crc32 - don't sleep in runtime pm
crypto: stm32/crc32 - fix multi-instance
crypto: stm32/crc32 - fix run-time self test issue.
crypto: stm32/crc32 - fix ext4 chksum BUG_ON()
crypto: hisilicon/zip - Use temporary sqe when doing work
crypto: hisilicon - add device error report through abnormal irq
crypto: hisilicon - remove codes of directly report device errors through MSI
crypto: hisilicon - QM memory management optimization
crypto: hisilicon - unify initial value assignment into QM
...
A node that has the MRA role, it can behave as MRM or MRC.
Initially it starts as MRM and sends MRP_Test frames on both ring ports.
If it detects that there are MRP_Test send by another MRM, then it
checks if these frames have a lower priority than itself. In this case
it would send MRP_Nack frames to notify the other node that it needs to
stop sending MRP_Test frames.
If it receives a MRP_Nack frame then it stops sending MRP_Test frames
and starts to behave as a MRC but it would continue to monitor the
MRP_Test frames send by MRM. If at a point the MRM stops to send
MRP_Test frames it would get the MRM role and start to send MRP_Test
frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each MRP instance has a priority, a lower value means a higher priority.
The priority of MRP instance is stored in MRP_Test frame in this way
all the MRP nodes in the ring can see other nodes priority.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fl_flow_key structure is around 500 bytes, so having two of them
on the stack in one function now exceeds the warning limit after an
otherwise correct change:
net/sched/cls_flower.c:298:12: error: stack frame size of 1056 bytes in function 'fl_classify' [-Werror,-Wframe-larger-than=]
I suspect the fl_classify function could be reworked to only have one
of them on the stack and modify it in place, but I could not work out
how to do that.
As a somewhat hacky workaround, move one of them into an out-of-line
function to reduce its scope. This does not necessarily reduce the stack
usage of the outer function, but at least the second copy is removed
from the stack during most of it and does not add up to whatever is
called from there.
I now see 552 bytes of stack usage for fl_classify(), plus 528 bytes
for fl_mask_lookup().
Fixes: 58cff782cc ("flow_dissector: Parse multiple MPLS Label Stack Entries")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps for packets that are sampled / trapped by ACLs, so that
capable drivers could register them with devlink. Add documentation for
every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add layer 3 control packet traps such as ARP and DHCP, so that capable
device drivers could register them with devlink. Add documentation for
every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add layer 2 control packet traps such as STP and IGMP query, so that
capable device drivers could register them with devlink. Add
documentation for every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This type is used for traps that trap control packets such as ARP
request and IGMP query to the CPU.
Do not report such packets to the kernel's drop monitor as they were not
dropped by the device no encountered an exception during forwarding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The action is used by control traps such as IGMP query. The packet is
flooded by the device, but also trapped to the CPU in order for the
software bridge to mark the receiving port as a multicast router port.
Such packets are marked with 'skb->offload_fwd_mark = 1' in order to
prevent the software bridge from flooding them again.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that hit exceptions during layer 3 forwarding must be trapped to
the CPU for the control plane to function properly. Create a dedicated
group for them, so that user space could choose to assign a different
policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next
to extend ctnetlink and the flowtable infrastructure:
1) Extend ctnetlink kernel side netlink dump filtering capabilities,
from Romain Bellan.
2) Generalise the flowtable hook parser to take a hook list.
3) Pass a hook list to the flowtable hook registration/unregistration.
4) Add a helper function to release the flowtable hook list.
5) Update the flowtable event notifier to pass a flowtable hook list.
6) Allow users to add new devices to an existing flowtables.
7) Allow users to remove devices to an existing flowtables.
8) Allow for registering a flowtable with no initial devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not register to netdev events to set up indirect blocks
anymore. Remove __flow_indr_block_cb_register() and
__flow_indr_block_cb_unregister().
The frontends set up the callbacks through flow_indr_dev_setup_block()
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update existing frontends to use flow_indr_dev_setup_offload().
This new function must be called if ->ndo_setup_tc is unset to deal
with tunnel devices.
If there is no driver that is subscribed to new tunnel device
flow_block bindings, then this function bails out with EOPNOTSUPP.
If the driver module is removed, the ->cleanup() callback removes the
entries that belong to this tunnel device. This cleanup procedures is
triggered when the device unregisters the tunnel device offload handler.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to initialize the flow_block_offload structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel devices provide no dev->netdev_ops->ndo_setup_tc(...) interface.
The tunnel device and route control plane does not provide an obvious
way to relate tunnel and physical devices.
This patch allows drivers to register a tunnel device offload handler
for the tc and netfilter frontends through flow_indr_dev_register() and
flow_indr_dev_unregister().
The frontend calls flow_indr_dev_setup_offload() that iterates over the
list of drivers that are offering tunnel device hardware offload
support and it sets up the flow block for this tunnel device.
If the driver module is removed, the indirect flow_block ends up with a
stale callback reference. The module removal path triggers the
dev_shutdown() path to remove the qdisc and the flow_blocks for the
physical devices. However, this is not useful for tunnel devices, where
relation between the physical and the tunnel device is not explicit.
This patch introduces a cleanup callback that is invoked when the driver
module is removed to clean up the tunnel device flow_block. This patch
defines struct flow_block_indr and it uses it from flow_block_cb to
store the information that front-end requires to perform the
flow_block_cb cleanup on module removal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function schedules the flow teardown state and it forces a gc run.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
trying to configure TC 'act_gate' rules with invalid control actions, the
following splat can be observed:
general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 1 PID: 2143 Comm: tc Not tainted 5.7.0-rc6+ #168
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
RIP: 0010:hrtimer_active+0x56/0x290
[...]
Call Trace:
hrtimer_try_to_cancel+0x6d/0x330
hrtimer_cancel+0x11/0x20
tcf_gate_cleanup+0x15/0x30 [act_gate]
tcf_action_cleanup+0x58/0x170
__tcf_action_put+0xb0/0xe0
__tcf_idr_release+0x68/0x90
tcf_gate_init+0x7c7/0x19a0 [act_gate]
tcf_action_init_1+0x60f/0x960
tcf_action_init+0x157/0x2a0
tcf_action_add+0xd9/0x2f0
tc_ctl_action+0x2a3/0x39d
rtnetlink_rcv_msg+0x5f3/0x920
netlink_rcv_skb+0x121/0x350
netlink_unicast+0x439/0x630
netlink_sendmsg+0x714/0xbf0
sock_sendmsg+0xe2/0x110
____sys_sendmsg+0x5b4/0x890
___sys_sendmsg+0xe9/0x160
__sys_sendmsg+0xd3/0x170
do_syscall_64+0x9a/0x370
entry_SYSCALL_64_after_hwframe+0x44/0xa9
this is caused by hrtimer_cancel(), running before hrtimer_init(). Fix it
ensuring to call hrtimer_cancel() only if clockid is valid, and the timer
has been initialized. After fixing this splat, the same error path causes
another problem:
general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 PID: 980 Comm: tc Not tainted 5.7.0-rc6+ #168
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
RIP: 0010:release_entry_list+0x4a/0x240 [act_gate]
[...]
Call Trace:
tcf_action_cleanup+0x58/0x170
__tcf_action_put+0xb0/0xe0
__tcf_idr_release+0x68/0x90
tcf_gate_init+0x7ab/0x19a0 [act_gate]
tcf_action_init_1+0x60f/0x960
tcf_action_init+0x157/0x2a0
tcf_action_add+0xd9/0x2f0
tc_ctl_action+0x2a3/0x39d
rtnetlink_rcv_msg+0x5f3/0x920
netlink_rcv_skb+0x121/0x350
netlink_unicast+0x439/0x630
netlink_sendmsg+0x714/0xbf0
sock_sendmsg+0xe2/0x110
____sys_sendmsg+0x5b4/0x890
___sys_sendmsg+0xe9/0x160
__sys_sendmsg+0xd3/0x170
do_syscall_64+0x9a/0x370
entry_SYSCALL_64_after_hwframe+0x44/0xa9
the problem is similar: tcf_action_cleanup() was trying to release a list
without initializing it first. Ensure that INIT_LIST_HEAD() is called for
every newly created 'act_gate' action, same as what was done to 'act_ife'
with commit 44c23d7159 ("net/sched: act_ife: initalize ife->metalist
earlier").
Fixes: a51c328df3 ("net: qos: introduce a gate control flow action")
CC: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When neighbor suppression is enabled the bridge device might reply to
Neighbor Solicitation (NS) messages on behalf of remote hosts.
In case the NS message includes the "Source link-layer address" option
[1], the bridge device will use the specified address as the link-layer
destination address in its reply.
To avoid an infinite loop, break out of the options parsing loop when
encountering an option with length zero and disregard the NS message.
This is consistent with the IPv6 ndisc code and RFC 4886 which states
that "Nodes MUST silently discard an ND packet that contains an option
with length zero" [2].
[1] https://tools.ietf.org/html/rfc4861#section-4.3
[2] https://tools.ietf.org/html/rfc4861#section-4.6
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alla Segal <allas@mellanox.com>
Tested-by: Alla Segal <allas@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After allocating the spare nexthop group it should be tested for kzalloc()
returning NULL, instead the already used nexthop group (which cannot be
NULL at this point) had been tested so far.
Additionally, if kzalloc() fails, return ERR_PTR(-ENOMEM) instead of NULL.
Coverity-id: 1463885
Reported-by: Coverity <scan-admin@coverity.com>
Signed-off-by: Patrick Eigensatz <patrickeigensatz@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-06-01
Here's one last bluetooth-next pull request for 5.8, which I hope can
still be accepted.
- Enabled Wide-Band Speech (WBS) support for Qualcomm wcn3991
- Multiple fixes/imprvovements to Qualcomm-based devices
- Fix GAP/SEC/SEM/BI-10-C qualfication test case
- Added support for Broadcom BCM4350C5 device
- Several other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
