Modules: YMFPCI driver
We better pretend that the ymfpci timer runs at 48 kHz because the
interrupt frequency cannot be higher, and clients that would try to
use 96 kHz would run at half their desired speed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA sequencer
When no default timer frequency has been set, initialize_timer() just
uses the maximum frequency supported by the timer, which is ridiculously
high on 96 kHz timers.
This patch introduces a default frequency of 1000 Hz for this case, and
makes sure that a frequency set by the user isn't too high.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Maestro3 driver
This patch fixes the maestro3 driver to call the snd_m3_assp_init
function to write the DSP firmware into the ASSP chip before sending the
RUN_ASSP command, thereby solving the hang after a cold boot.
Signed-off-by: Charles R. Anderson <cra@alum.wpi.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
- Set buggy_irq parameter before registration of irq handler.
- Clean up module parameter handling.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: VIA82xx driver
The change only affects the via823x kind of chips.
Here the via8233_pcm_pointer_hw() function
(named snd_via8233_pcm_pointer() before)
needed to loop until a non zero position is red from the chip.
Measurements have shown that more than 200 loops are typically needed on
an Athlon64.
As io-reads cost many cycles, those loops sum up huge.
via8233_pcm_pointer_hw() runs either in interrupt or with interrupts
disabled. So it introduces significant interrupt latency.
The patch introduces a calculated position value hwptr_done,
that is updated by the interrupt routine when a period is completed.
It is only used, if the 823x chip returns a zero position, which can't
be interpreted reliably.
Further optimisation is applied on the 8233 chip's interrupt routine:
Only the SGD_SHADOW is read, as it contains all infos needed.
We ommit ~5 more register reads that way.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
Remove the usb_reset_configuration() call from the probe callback
because it isn't needed and it may interfere with other drivers
already loaded for the device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: VIA82xx driver
The patch enable separate DXS controls of sound function of VIA VT82xx
controller in case DXS volume is not needed for PCM Playback volume
control emulation.
Signed-off-by: Honza Maly <hkmaly@matfyz.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,MIPS AU1x00 driver,PPC Beep,SPARC DBRI driver
Removed the use of chip_t, which was obsoleted.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Timer Midlevel
Split or rewrite lines that are longer than 80 characters, and remove
whitespaces at the end of lines.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Timer Midlevel
The return value of list_entry() already has the type from the second
argument, so we don't need to typecase it again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: RTC timer driver,Timer Midlevel
Add a module pointer to the timer structure and use it for refcounting
instead of the card's module pointer to prevent the global timer
modules (rtctimer and hpetimer) from being removed while in use.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ES1938 driver
- Clean up the last PM fix
- Add TRIGGER_SUSPEND/RESUME to disable/enable DMA properly during PM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES1938 driver
This patch fixes the suspend/resume issue I'm having with ESS-Solo1
soundcard. Without this patch I might get after resume message
that kernel is disabling the IRQ5 (soundcard). If there was something
playing it wont continue after resume without this patch.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove vmalloc wrapper
- Add release_and_free_resource() to remove kfree_nocheck() from each driver
and simplify the code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA Core,ALSA<-OSS emulation
Remove a global function snd_task_name(), and move it local
to snd-pcm-oss module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,PCM Midlevel,Timer Midlevel,ALSA Core
Use the standard getnstimeofday() function instead of ALSA's own one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove snd_runtime_check() macro.
This macro worsens the readability of codes. They should be either
normal if() or removable asserts.
Also, the assert displays stack-dump, instead of only the last caller
pointer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
On my Acer Aspire 3003LCi laptop, the speaker volume is not controlled
by the master control, but by the headphone control. Enabling the
'hp_only' quirk corrects this. The patch below adds this device to the
list of known quirks.
Signed-off-by: Dick Streefland <dick@streefland.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ICE1724 driver
Remove the restcition of sample rates on Revolution 7.1 board.
This enables the low 8-44kHz sample rates.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the code for supporting eight cards from the integrated
controller drivers because There Can Be Only One controller of
each type per mainboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Sound Core,PCI drivers
AC97 Kconfig entries broke the ALSA device drivers menu,
so move them to a location where that won't happen,
enabling all device sub-menus to be presented together.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch cleans last ac97 audio/modem codec interception in
initialization procedures (ac97_mixer_new()) and removes obsolete
SHARED_TYPE 'locking' which prevents from AMC codecs to function
correctly.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
This patch adds a new mixer control called 'IEC958 Loop' which makes
it possible to loop digital signals from S/PDIF-in to S/PDIF-out.
Signed-off-by: Glen Masgai <mimosius@gmx.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA sequencer
Remove the last parameter of snd_seq_timer_set_tick_resolution()
because it is always one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: RTC timer driver
The check whether rtctimer_freq is a power of two can be done easier
with a simple bit operation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: RTC timer driver
The rtc_inc variable is never used outside the interrupt handler, and
is always one where it matters, so we can just remove it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Move the usb_complete_callback() compatibility wrapper out of the
kernel tree.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Move the usb_pipe_needs_resubmit() compatibility wrapper out of the
kernel tree.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Add more comments about other device modes and unsupported devices to
the Roland part of the quirks table.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Add a quirk entry for the Hercules DJ Console to ignore timeouts on
some mixer control transfers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Simplify the handling of MIDI quirks by treating an interface without
quirks as a QUIRK_MIDI_STANDARD_INTERFACE.
This also fixes the bug where a MIDI_STANDARD quirk would not be
recognized.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: CMIPCI driver
If possible, use ports in the card's PCI port address range instead of
the legacy ports.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: HDA Intel driver
This patch is to make the Intel HDA code work for NVIDIA azalia controller.
Modified by Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod G. <vinodg@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: EMU10K1/EMU10K2 driver
Adds left and right front channel outputs using fxbus 8 and 9 and 'Front'
playback and capture volume controls.
Signed-off-by: Mikael Magnusson <mikma@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds the magic IO wakeup code for the CardBus version of the
Creative Labs Audigy 2 to the snd-emu10k1 driver.
Without the magic IO enable sequence, reading from the IO region of the
card will fail spectacularly, and the machine will hang.
My next task will be getting the driver to actually play sound without
distortion.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
[ This is a work-in-progress, but since it avoids a total lockup
if the emu10k module is loaded on a machine with the cardbus
card inserted, we're better off with it than without it, even
if sound quality is bad right now ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Typo fix: dots appearing after a newline in printk strings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed some more references to check_region().
I checked these changes into the 'checkreg' branch of
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6.git
The only valid references remaining are in:
drivers/scsi/advansys.c
drivers/scsi/BusLogic.c
drivers/cdrom/sbpcd.c
sound/oss/pss.c
Remove last vestiges of ide_check_region()
drivers/char/specialix: trim trailing whitespace
drivers/char/specialix: eliminate use of check_region()
Remove outdated and unused references to check_region()
[sound oss] remove check_region() usage from cs4232, wavfront
[netdrvr eepro] trim trailing whitespace
[netdrvr eepro] remove check_region() usage
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove PageReserved() calls from core code by tightening VM_RESERVED
handling in mm/ to cover PageReserved functionality.
PageReserved special casing is removed from get_page and put_page.
All setting and clearing of PageReserved is retained, and it is now flagged
in the page_alloc checks to help ensure we don't introduce any refcount
based freeing of Reserved pages.
MAP_PRIVATE, PROT_WRITE of VM_RESERVED regions is tentatively being
deprecated. We never completely handled it correctly anyway, and is be
reintroduced in future if required (Hugh has a proof of concept).
Once PageReserved() calls are removed from kernel/power/swsusp.c, and all
arch/ and driver code, the Set and Clear calls, and the PG_reserved bit can
be trivially removed.
Last real user of PageReserved is swsusp, which uses PageReserved to
determine whether a struct page points to valid memory or not. This still
needs to be addressed (a generic page_is_ram() should work).
A last caveat: the ZERO_PAGE is now refcounted and managed with rmap (and
thus mapcounted and count towards shared rss). These writes to the struct
page could cause excessive cacheline bouncing on big systems. There are a
number of ways this could be addressed if it is an issue.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Refcount bug fix for filemap_xip.c
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous patch adding the ability to nest struct class_device
changed the paramaters to the call class_device_create(). This patch
fixes up all in-kernel users of the function.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch fixes Oops from sound drivers using generic platform device
but have no suspend/resume callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Added a control for the input source (which can be either
"line" or "mic")
o Mute the speaker/line-out/headphone outputs by default.
o Increased the buffer size from 10 pages to 16.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
ALSA Harmony was resetting the capture position when
preparing the capture substream, which it shouldn't do.
This should fix the problem.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
ALSA Harmony should no longer play junk (left in the buffers
from a previous stream) at the start of a new stream.
Implement the monitor mixer channel for ALSA Harmony.
Also prevent snd_harmony_volume_get from returning negative values.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
Use the graveyard/silence buffers in ALSA Harmony.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
USB generic driver
Add a quirk entry for the external MIDI ports of the
Windows Edition of the Hercules DJ Console.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add a mixer quirk entry for the Hercules DJ Console (Windows Edition)
that uses a different USB product ID.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
EMU10K1/EMU10K2 driver
Fixed the handling of ac97_chip=2 capability type.
The error occurs in snd_ac97_mixer(), not in snd_ac97_bus().
Also, release the unnecessary ac97_bus object in the error path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
Fixed the error at loading SBLive Game board (and possible other models).
The PCI SSIDs of this board conflicts with SB Live 5.1 Platinum, which has
no AC97 chip.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Mark the ALC882 'LFE Playback Switch' as an input, like the other
playback switch settings.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Fix a typo (cut & paste) in the alc880_test_mixer structure.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
The ALC260 'Mono Playback Switch' is marked as an output in
patch_realtek.c. It actually does not work unless it is marked as an
input. Go figure... This was tested and confirmed on an HP xw4300.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
Increase the maximum PCM buffer size to 1 MB. The USB driver doesn't
have any inherent buffer size limit, and big multichannel interfaces
may benefit from this.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
There is another revision of the PHASE26 with a different product ID;
add a quirk entry for that, too.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add a quirk entry for the Roland RD-700SX.
This should work for the RD-300SX, too.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
AC97 Codec
A single call to the driver suspend/resume method for each device is
enough. The level and SUSPEND_*/RESUME_* arguments are deprecated and
said to be removed eventually anyway (no other subsystem are using them
anymore except platform devices).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
Don't use dev.platform_data to store a reference to the containing
ac97_t structure. Such assignment is redundent since we can deduce the
ac97_t structure location from the contained device structure. This
sets platform_data free for other purposes.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
The bus_id is initialized with a generic identifier string which is not
really useful for proper driver matching. Let the driver decide what it
needs via its probe method instead.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
Add a quirk entry for the Hercules DJ Console to ignore timeouts on
some mixer control transfers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
HDA Intel driver
Disable the auto-correction of DMA position temporarily.
It doesn't work as expected yet...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
No index is templated for si3036 modem controls.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
From: Christopher Zimmermann <madroach@zakweb.de>
This patch enables SBus support for the cs4231 sound driver.
It is tested on an Ultra2. Capture and playback both work.
I experienced lags and crashes using certain threaded
players like ogg123 and mp3blaster, while the former is
lagging far more. This behavior may be specific to SMP
systems. It is reproducable using the dummy sound card
driver. Sox works flawlessly.
Setting up the calculation of ptr in snd_cs4231_playback_pointer
was a bit strange. I got it to work by not incrementing the
[pc]_periods_sent counter when starting DMA the first time
in cs4231_dma_trigger. Therefore this dummy thing.
[ I did some minor cleanups -DaveM ]
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up some pm_message_t types
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While doing an allyesconfig build, I noticed that the commit
commit 8cdfd2519c
Author: Takashi Iwai <tiwai@suse.de>
Date: Wed Sep 7 14:08:11 2005 +0200
[ALSA] Remove superfluous PCI ID definitions
broke the RME32 and RME96 drivers, since the PCI IDs they use seem to have
changed names. Here's a patch to fix this -- compile tested only, since I
have no idea what the hardware even is.
Fix the build of the RME32 and RME96 drivers by having them use the
PCI_DEVICE_ID_RME_xxx names defined in <linux/pci_ids.h> instead of the
PCI_DEVICE_ID_xxx names that they used to define themselves.
Also fix the typo in the id PCI_DEVICE_IDRME__DIGI96_8_PAD_OR_PST so the
name is PCI_DEVICE_ID_RME_DIGI96_8_PAD_OR_PST.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SPARC DBRI driver
This patch contains the following fixes to the Alsa DBRI driver:
- Remove 2.6.13 build warning on the prom_getproperty() call.
- Rework command synchronization: send a sequence number with D_WAIT,
and check it in the completion interrupt.
Move synchronization delays from _cmdsend() to _cmdlock() allowing the
CPU to do other usefull things while the DBRI is processing the
commands.
- Fix first argument of printk() calls.
- Enable burst transfers for DBRI. Original 2.4 patch from Krzysztof
Helt
- Make dbri_debug module parameter writable from sysfs. Remove obsolete
write access to the /proc debug file.
- Replace udelay() with msleep_interruptible() where possible.
- Update documentation comments.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,Intel8x0 driver
Added buggy_semaphore module option to snd-intel8x0 driver
for a workaround for hardwards with buggy codec semaphores.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver,HDA Intel driver,HDA generic driver
Assign audio PCMs first before modem PCMs.
The modem stream is assigned up to device #6, to be consistent over
different models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PPC PMAC driver
Here is a patch to correct detection of the soundcard on my iBook model
(bought really recently).
Without that fix, there were only andui in the headphone, and the mixer
was totaly non functional.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA Core,ALSA sequencer
Add an option to make the RTC timer the default sequencer timer. This
becomes necessary for precise MIDI timing when the system timer runs at
less than 1000 Hz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
ALSA Core
A new function snd_card_set_generic_dev() is introduced to add the
'generic device' support for devices without proper bus on sysfs.
It's a last resort, and should be removed in future when they have
a proper bus, instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
Check the validity of the current DMA position when position_fix=0 (auto)
is set. If the DMA position overcomes the threshold, the driver changes
the fix behavior automatically to use POSBUF.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ARM AACI PL041 driver,PARISC Harmony driver
Added snd_card_set_dev() calls to register the device pointer for the card.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Add the subsystem PCI devid to the list (on top of 2.6.13).
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Opti9xx drivers
When clearing some bits in a register, don't bother with the bits that
won't be changed anyway.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
ALSA Core,RawMidi Midlevel,ALSA<-OSS emulation,ALSA sequencer
RME32 driver,RME96 driver,EMU10K1/EMU10K2 driver,NM256 driver
Add sparse annotations where we do strange this with __iomem/__user
pointers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add the SNDRV_PCM_INFO_BATCH flag to the PCM hardware information to
indicate that the driver uses double buffering.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
CA0106 driver,EMU10K1/EMU10K2 driver
A thread appeared on the LKML. This patch implements the fix.
Question:
in sysfs, /sys/bus/*/drivers lists the driver names, with their exported .name (eg. '.name = 'EMU10K1_Audigy'' in the module code, from now on 'driver name'). In /sys/modules, the kernel modules are listed with their module name, eg. snd_emu10k1. However, it seems to me that in sysfs, there is no way in particular to tell, which module has which .name. That is, that snd_emu10k1 is EMU10K1_Audigy and vice versa.
I wonder whether it wouldn't be possible to add a symlink to the particular module from the driver, and/or from the module to the driver, so the list of devices handled by the module and the module name would be accessible. This way, I would know which driver name corresponds to which module name and vice versa.
Answer:
For PCI drivers, just add the line:
.owner = THIS_MODULE,
to their struct pci_driver definition and you will get the symlink
created for you.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
AC97 Codec
Fix the internal speaker problem (e.g. Targa Traveller 826)
with ALC658D codec. The info is taken from Cyberlink/realtek-modified code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RME HDSP driver
When using the kernel firmware loader, initialize the card shortname
before registering the card with ALSA to prevent it from using a
default card ID.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
PCI drivers,AD1889 driver
move the AD1889 driver to the kernel tree
Acked-by: Thibaut Varene <varenet@parisc-linux.org>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
CA0106 driver
Playback volume controls were appearing in both the playback and capture
displays of alsamixer. Now those playback controls only appear in the
playback display.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
We do no longer need a template for OSS drivers.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up timer initialization by introducing DEFINE_TIMER a'la
DEFINE_SPINLOCK. Build and boot-tested on x86. A similar patch has been
been in the -RT tree for some time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
29 July 2005, Cambridge, MA:
This afternoon Alan Stern submitted a patch to remove the URB_ASYNC_UNLINK
flag from the Linux kernel. Mr. Stern explained, "This flag is a relic
from an earlier, less-well-designed system. For over a year it hasn't
been used for anything other than printing warning messages."
An anonymous spokesman for the Linux kernel development community
commented, "This is exactly the sort of thing we see happening all the
time. As the kernel evolves, support for old techniques and old code can
be jettisoned and replaced by newer, better approaches. Proprietary
operating systems do not have the freedom or flexibility to change so
quickly."
Mr. Stern, a staff member at Harvard University's Rowland Institute who
works on Linux only as a hobby, noted that the patch (labelled as548) did
not update two files, keyspan.c and option.c, in the USB drivers' "serial"
subdirectory. "Those files need more extensive changes," he remarked.
"They examine the status field of several URBs at times when they're not
supposed to. That will need to be fixed before the URB_ASYNC_UNLINK flag
is removed."
Greg Kroah-Hartman, the kernel maintainer responsible for overseeing all
of Linux's USB drivers, did not respond to our inquiries or return our
calls. His only comment was "Applied, thanks."
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a memory-leak tracking version of kzalloc for ALSA.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Jiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
asm/segment.h varies greatly on different architectures but is clearly
deprecated. Removing all non-architecture consumers will make it easier
for us to get ride of asm/segment.h all together.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ensure that sound/arm/Makefile is sanely organised so that additions to it
don't break all other patches out there. This means I only have to adjust
the line numbers in my patch queue rather than having to re-generate by
hand those which touch this file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In sound/isa/Kconfig, select ISAPNP and depend on ISAPNP are intermixed,
resulting in funny behaviour. (Soundcarts get selectable if other
soundcards are selected).
This patch changes the "depend on ISAPNP"s to select.
Signed-Off-By: Bodo Eggert <7eggert@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
USB generic driver
When a USB error occurs that might indicate that the device has been
unplugged, don't resubmit the URB immediately to prevent flooding the
log with error messages before khubd has us disconnect()ed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add register_sound_special_device() function to allow assignment of
device pointer to a specific OSS device for HAL.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
Emagic devices pad their packets not with 0xff bytes but with a 0xff
byte followed by garbage, so we have to stop at the first such byte.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
HDA Intel driver
Fix and clean up for the support of ULI M5461
- set CORB/RIRB sizes explicitly
- add workarounds for ULI on ia32
- max number of streams depends on the chip type now
- increase the size of BDL
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
The insertion of the rate 9600 make a shift in detection of supported
rate, put this rate at the end of the list.
Signed-off-by: Nicolas Graziano <nicolas.graziano@wanadoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel8x0 driver,AC97 Codec
The HP nx6110 laptop needs to have Headphone Jack Sense enabled so
that the internal speakers will be turned off when headphones are
plugged in.
Also ac97_quirk=hp_only is needed to make a single Master volume in
the mixer instead of separate volumes for internal speakers and
headphones, which just confuses the user.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digigram VX core,CS4231 driver,ATIIXP driver,VIA82xx driver
VIA82xx-modem driver,au88x0 driver,CS46xx driver,Trident driver
This patch disables SNDRV_PCM_INFO_RESUME flag for drivers which does not
support the full resume.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
AC97 Codec
The patch fixes the bus_id conflict error when registering two codecs
of the same type (ALSA bug#1334).
Signed-off-by: Bjorge Dijkstra <bjorge@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NM256 driver
- Fixed the PCM resume - restoring the rate setting
- Fixed the handling of buggy irqs
- Dynamically acquire/release irq handler to make the driver more robust
to unknown irq storms (as OSS driver does).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
- removed SNDRV_PCM_INFO_RESUME (the driver cannot do PCM resume at the time)
- fixed chip->pcm_devs initialization
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
PCM Midlevel
Fixed the handling of boundary in PCM 32bit compat layer.
Positions in hwsync are bound in the 32bit boundary size.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
OPL3SA2 driver
- use different name (opl3sa2-pnpbios) for PnP BIOS driver
- don't print warning when manual config of resources fails (PnP BIOS)
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
AC97 Codec
Make the patch_wolfson_wm97??_specific() functions static again.
This patch was accidentally reverted in rev. 1.92.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
With the double buffering, we no longer need contiguous memory for the
PCM buffer, so we can use vmalloc() instead of the preallocation
functions, and increase the maximum size to 256 KB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Use the USB buffer allocation functions to avoid repeated DMA mappings
of our buffers, which are re-used quite a lot.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Take the substream lock when reading hwptr_done to avoid a race
condition with the updates in the URB callbacks.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Change prepare_playback_urb() not to stop preparing packets before a
frame boundary has been reached.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
We always had to use double buffering when capturing, and when playback
data for one URB crosses a buffer boundary. The latter would make hwptr
updates less precise because the double-buffered data is read from the
buffer much earlier than the other data is read by the host controller.
Double-buffering all data allows to update hwptr immediately after the
data was copied to the USB buffer(s), which has the additional benefit
of avoiding the latency imposed by the host controller's delay of up to
one frame when interrupting.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
When preparing capture URBs, we don't need to stop when we cross a
period boundary because we now never handle more than one millisecond of
data per URB anyway.
When handling captured data, use an extra flag to call
snd_pcm_period_elapsed() no more than once. This allows us to move the
period boundary checking code before the copying of the data which
avoids a second locking of the substream's lock.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
OPL3SA2 driver
The driver has been extended to support also PnP BIOS devices.
The detection path is:
1) detect PnP BIOS devices
2) detect ISA PnP devices
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
VIA82xx driver
Added the DXS entry for MSI K8MM-V.
Also fixed a typo in last patch for Acer Aspire 1524 WLMi.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
The EHCI driver doesn't interrupt more than once per millisecond, and
organizes all iso transfers with frame-sized ITDs, so we can (try to)
be more efficient by aligning all URBs on frame boundaries.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
