The intent is for SYSCLK to be tied to all input and output widgets such
that it turns on whenever the chip is in use. It is not tied to the DRC
signal activity detect virtual outputs, whilst in practice this is
unlikely to cause an issue (as an input will likely also be powered up)
best to correct.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform_driver does not need to set an owner as it will be
populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Inform the notifier chain if the DSP recognises a voice trigger.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a notifier chain that can be used from the machine driver to catch
events generated by the CODEC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new
drivers. Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uNKQ
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new drivers.
Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support"
* tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
ALSA: hda - Fix headset mic detection problem for one Dell machine
spi: spi-ep93xx: Fix the PTR_ERR() argument
ALSA: hda/realtek - Add support for ALC295/ALC3254
ASoC: kirkwood: fix build failure
ALSA: hda - Fix headphone noise on Dell XPS 13 9360
ASoC: ak4642: Enable cache usage to fix crashes on resume
ASoC: twl6040: Disconnect AUX output pads on digital mute
ASoC: tlv320aic32x4: Properly implement the positive and negative pins into the mixers
rcar: src: skip disabled-SRC nodes
ASoC: max98371 Remove duplicate entry in max98371_reg
ASoC: twl6040: Select LPPLL during standby
ASoC: rsnd: don't use prohibited number to PDMACHCRn.SRS
ASoC: simple-card: Add pm callbacks to platform driver
ASoC: pxa: Fix module autoload for platform drivers
ASoC: topology: Fix memory leak in widget creation
ASoC: Add max98371 codec driver
ASoC: rsnd: count .probe/.remove for rsnd_mod_call()
ASoC: topology: Check size mismatch of ABI objects before parsing
ASoC: topology: Check failure to create a widget
ASoC: add support for TAS5720 digital amplifier
...
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SSICKR (Gen2) / BRGCKR (Gen3) 31bit mask should be opened,
because BRGB (= for 48kHz) might select it.
Special thanks Yokoyama-san
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While building m32r allmodconfig the build failed with:
ERROR: "bad_dma_ops" [sound/soc/kirkwood/snd-soc-kirkwood.ko] undefined!
To satisfy the dependency CONFIG_SND_KIRKWOOD_SOC should depend on
HAS_DMA.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any
core code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QsAc
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any core
code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver"
* tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (177 commits)
ALSA: firewire-lib: change a member of event structure to suppress sparse wanings to bool type
sound: oss: Use setup_timer and mod_timer.
ASoC: hdac_hdmi: Remove the unused 'timeout' variable
ASoC: fsl_ssi: Fix channel slipping on capture (or playback) restart in full duplex.
ASoC: fsl_ssi: Fix channel slipping in Playback at startup
ASoC: fsl_ssi: Fix samples being dropped at Playback startup
ASoC: fsl_ssi: Save a dev reference for dev_err() purpose.
ASoC: fsl_ssi: The IPG/5 limitation concerns the bitclk, not the sysclk.
ASoC: fsl_ssi: Real hardware channels max number is 32
ASoC: pcm5102a: Add support for PCM5102A codec
ASoC: hdac_hdmi: add link management
ASoC: Intel: Skylake: add link management
ALSA: hdac: add link pm and ref counting
ALSA: au88x0: Fix zero clear of stream->resources
ASoC: rt298: Add DMI match for Broxton-P reference platform
ASoC: rt298: fix null deref on acpi driver data
ASoC: dapm: deprecate MICBIAS widget type
ALSA: firewire-lib: drop skip argument from helper functions to queue a packet
ALSA: firewire-lib: add context information to tracepoints
ALSA: firewire-lib: permit to flush queued packets only in process context for better PCM period granularity
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
The ak4642 driver is using a regmap cache sync to restore the
configuration of the chip on resume but (as Peter observed) does not
actually define a register cache which means that the resume is never
going to work and we trigger asserts in regmap. Fix this by enabling
caching.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Disconnect also the path to AUXL from the HF path during digital_mute to
avoid pop noise leakage to Line-out pads.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
* acpi-pci:
ACPI,PCI,IRQ: remove SCI penalize function
ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()
ACPI,PCI,IRQ: reduce static IRQ array size to 16
ACPI,PCI,IRQ: reduce resource requirements
* acpi-misc:
ACPI / sysfs: fix error code in get_status()
ACPI / device_sysfs: Clean up checkpatch errors
ACPI / device_sysfs: Change _SUN and _STA show functions error return to EIO
ACPI / device_sysfs: Add sysfs support for _HRV hardware revision
arm64: defconfig: Enable ACPI
ACPI / ARM64: Remove EXPERT dependency for ACPI on ARM64
ACPI / ARM64: Don't enable ACPI by default on ARM64
acer-wmi: Use acpi_dev_found()
eeepc-wmi: Use acpi_dev_found()
ACPI / utils: Rename acpi_dev_present()
* acpi-tools:
tools/power/acpi: close file only if it is open
Happened when the Playback (or Capture) is running continuously
and Capture (or Playback) is restarted (xrun, manual stop/start...)
Since the RX (or TX) FIFO are only reset when the whole SSI is disabled,
pending samples from previous capture (or playback) session may still
be present. They must be erased to not introduce channel slipping.
FIFO Clear register fields are documented in IMX51, IMX35 reference manual.
They are not documented in IMX50 or IMX6 RM, despite they are
working as expected on IMX6SL and IMX6solo.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, SCR.SSIEN and SCR.TE were enabled at once if no capture
stream was also running.
This may not give a chance for the DMA to write the first sample in
TX FIFO before the streaming starts on the PCM bus, inserting void
samples first.
Those void samples are then responsible for slipping the channels.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the capture is already running while playback is started, it is highly
probable (>80% in a 8 channels scenario) that samples are lost between
the DMA and TX fifo.
The reason is that SIER.TDMAE is set before STCR.TFEN0, leaving a time
window where the FIFO doesn't receive the samples written by the DMA.
This particular case happened only if capture is already enabled as
SCR.SSIEN is already set at the playback startup instant.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of functions only receive the ssi_private reference and don't have
a knowledge of 'dev' pointer, even for debug purpose.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
im6sl reference manual 47.7.4:
"
Bit clock - Used to serially clock the data bits in and out of the SSI port.
This clock is either generated internally (from SSI's sys clock) or taken
from external clock source (through the Tx/Rx clock ports).
[...]
Care should be taken to ensure that the bit clock frequency (either
internally generated by dividing the SSI's sys clock or sourced from
external device through Tx/Rx clock ports) is never greater than 1/5
of the ipg_clk (from CCM) frequency.
"
Since, in master mode, the sysclk is a multiple of bitclk, we can
easily reach a high sysclk value, whereas keeping a reasonable bitclk.
ex: 8ch x 16bit x 48kHz = 6144000, requires a 24576000 sysclk (PM=1)
yet ipg_clk/5 = 66Mhz/5 = 13.2
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max number of slots in TDM mode is 32:
- Frame Rate Divider Control is a 5bit value
- Time slot mask registers control 32 slots.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320AIC32x4 has a very flexible mixer on the inputs to the ADCs. Each
mixer has an available set of available pins that can be connected to the
ADC positive and negative pins via three different resistor values. This
allows for configuration of differential inputs as well as doing level
manipulation between sources going into the mixers.
The current code only provides positive pins and I implemented the resistors
in an earlier patch. It turns out that it appears to more accurately model
what's happening to implement each of the pins as a MUX rather than on/off
switches and a mixer. This way each pin can be set to its desired resistor
value. Since there are no switches, the mixer is no longer necessary in the
DAPM path. I set the DAPM paths such that the "off" position of any of the
MUXes turns the path off.
This should allow for any input confiuration available on the codec.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some definitions to support the PCM5102A codec
by Texas Instruments.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Changes to original patch by Florian Meier:
* rebased (Makefile and Kconfig
* fixed checkpath errors (spaces, newlines)
* added dt-binding documentation
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Manage the hda idisp link using shiny new link APIs. We need to
keep link On while we probe and also hold the reference in runtime
resume and drop in suspend
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use shiny new link APIs to manage the links. Also remove old link
configuration logic from driver.
We need to keep link and cmd dma to off during active suspend
to allow system to enter low power state and turn it on if
the link and cmd dma was on before active suspend in active
resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current device tree representation of the R-Car Sample Rate Converters
(SRC) assumes that they are numbered consecutively, starting from 0. Alas,
this is not the case with the R8A7794 SoC where SRC0 isn't present. In
order to keep the existing device trees working, I'm suggesting to use a
disabled node for SRC0. Teach the SRC probe to just skip disabled nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton-P reference platform also uses combo jack for audio
connector so we need to set codec pdata to use this based on DMI
match for this board.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACPI driver data can be NULL so we need to check that before
dereference the driver data.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Format number after 0x in hex.
Cc: Jie Yang <yang.jie@linux.intel.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the codec is in standby we do not need to keep the HPPLL active.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current checking for PLL 32KHz mode fails in driver code when
bypassing the PLL. This is due to an incorrect check of PLL
source type when 32KHz clock is provided. Removal of this check
resolves the issue.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This update changes the dividers used for ranges of input MCLK
frequencies, to improve PLL locking for a corner case when at edge
of MCLK frequency input divider range.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently PC counter is always synchronised to DAI which means that
when the DAI is disabled, features such as ALC calibration cannot
be executed successfully. This patch makes sure that when the DAI
is disabled, PC counter is set to free-running.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the codec is DAI clk slave, and the SRM feature of the PLL
is being used, the enabling of the DAI should occur only after
the PLL has locked to the incoming WCLK. This update adds checking
to the the DAI widget event, so it waits for SRM to lock. There is
also a timeout if that lock doesn't occur within a given time.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, when Codec is I2S master DAI clocks are continuously
generated even if all audio streams have stopped. To improve
efficiency, control of the DAI clocks for master mode have been
moved to a DAPM widget event so they're only enabled as required.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the Broxton-P machine driver for Intel Broxton-P
reference boards. This machine uses the RT298 codec
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Broxton-P platform has 6 SSPs so we need to add ssp2 thru
ssp5 to DAI list for the driver.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dmapp_get_id() returns 0xFF as error code if system used
strange connection. It will be used as PDMACHCRn.SRS, but 0xFF is
prohibited number.
In order not to use prohibited number, this patch indicates error message
and returns 0x00 (same as SSI00) in error case.
Special thanks to Dung-san.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the ES8328 does support different rates for capture and
playback, only very limited combinations are supported (8kHz and 48kHz
or 8.0182kHz and 44.1kHz) with most rates required to be symmetric.
Instead of adding a lot of complexity for little gain, let's enforce
symmetric rates.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The values are the same for the DAC and ADC so remove the specific
values and use values with shifts.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a refactor in preparation for supporting more sample sizes which
has no functional change.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is always used along with ES8328_CONTROL1_ENREF so there is no
change in the generated code as a result of this fix.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADCCONTROL4 and DACCONTROL1 registers are similar but not identical,
with the DACCONTROL1 having each field starting one bit higher than
ADCCONTROL4.
Instead of introducing a magic shift, add new constants for the values
in ADCCONTROL4 and use a second variable to setup the ADC.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This ensures that the clock is setup after its frequency has been set;
the existing code in set_dai_fmt may be called before the clock rate has
been set resulting in an incorrect configuration.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the McASP is used as clock master and the reference clock is AUXCLK we
can have additional level of divider. The BCLK divider is limited to
maximum 32, if the desired bclk can not be reached with this, the AUXCLK
divider also needs to be used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the return value to error_pmm instead of the BCLK div and handle the
divider configuration to McASP within the function when the set flag is
true.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the first parameter to struct davinci_mcasp* from
struct snd_soc_dai*
The function internally does not use or need the DAI information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of hardwired IDs add defines for the available dividers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure that the user can not start multiple streams with the same
direction.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set snd_soc_pm_ops for the pm ops to make sure that the ASoC level of PM
operations are going to happen. This is needed to get suspend/resume
working correctly when the audio is using simple-card.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These platform drivers are lacking MODULE_ALIAS so module autoloading
doesn't work. Tested on corgi and poodle with kernel 4.4.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During skl_nhlt_init(), acpi obj pointer is allocated and never
freed and remap address is not unmapped.
To fix this we should release the ACPI obj and also unmap the
nhlt address during cleanup of driver.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
name and sname allocated in widget create are not freed when
creation is successful, so free them.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On mx6ul the General Purpose Register 1 (GPR1) contains the following
bits for configuring the direction of the SAI MCLKs:
SAI1_MCLK_DIR, SAI2_MCLK_DIR, SAI3_MCLK_DIR
Introduce the "fsl,sai-mclk-direction-output" optional property to allow
configuring the SAI_MCLK outputs.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MX6UL may need to configure the General Purpose Register 1 (GPR1), so
it is better to add a new compatible string to differentiate.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds "DLGS7219" ACPI id for the codec.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Tested-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only polling jd status when rt5645->pdata.jd_invert is true.
However, it should be done at all time since there will be no
interrupt for jd if we press a headset button and remove the
headset at the same time.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit eba65d179c.
This broke audio on Veyron Jerry Chromebooks and I now cannot reproduce
the problem I was trying to fix even with this commit reverted, so it
seems that this was completely the wrong thing to do.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 5938448b99.
It turns out that the commit that made these variables unused is wrong
so we're about to revert it. Bring back the variables in prepration.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If someone powers down the DSP core (through routing changes
say) whilst a compressed record is in progress we can end up
using a freed pointer to the buffer object. When a compressed
audio stream is triggered we attach it to a buffer on a physical
DSP. This patch adds a detach of the buffer from the stream when
the stream is freed or when the DSP is powered down which avoids
the situation where we use a buffer when it is no longer valid.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move wm_adsp_compr_attach and wm_adsp_compr_attached functions so they
will stay logically grouped with similar functions after some additional
changes.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We intended || here instead of &&. The original code potentially leads
to a NULL dereference.
Fixes: 2889099eb8 ('ASoC: hdac_hdmi: Register chmap controls and ops')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewd-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the arbitrary length TLV based binary
controls. This allows users to properly access controls that are
more than 512 bytes in length.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On WoV we can suspend the DMA and keep the DSP pipelines only On,
so remove the ignore_suspend for WoV streams but keep them for
WoV endpoints.
This helps in achieving better power by suspending DMAs
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For 'ignore_suspend' cases we need to keep DSP and pipes On, but
can suspend the stream and pause the DMA as we are not rendering
data during the suspended time.
For this we can check the dai widget ignore_suspend flag in
trigger suspend/resume, and start and stop the host DMA and host
copier pipelines.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If widget of a playback or capture DAI is already On, then no
need not send the Set DMA Control IPC message to firmware.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
param_data variable is allocated during set module format of init
instance is not getting freed and hence can cause a memory leak.
So free it up.
Signed-off-by: Mousumi Jana <mousumix.jana@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If request firmware fails at init, the code loader DMA allocation
can be NULL, so check for boot complete before freeing up these
resources
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXINZtAAoJECTWi3JdVIfQ+BwH/1eLqMfCSZM9nsDr1QMvOCDP
SO4ZoWqvYplBcS8pYKbJmqtuo8jMxT3VIQF+b5hPAVhgpLwMmy9qeFtatqCQ2WDC
GfCqW8LSKtrzwUwmoRrtHx7vfBLP1/z78F8ORQzwhrplTCBhvPLbUOrV51EFj6tf
Dfo2tW0uxww9iCZduYu4LadOhFOfuw+5shUrJk5A5f975Zbdgyke4CbRnlbDPXLq
d4i7bNfiISkSJiKMpdZFeiOQCd0+uXHh2WkMtVYSGVTA2Kf7d7HtX+JpEFFmaJgJ
8CndjgNJ1ZXtMHl1pMYmNqKJ5mEgmVtbGGJWY4QmQBva0EfQ+vLZt78BG3qvJwk=
=SXH2
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.6-rc5' into asoc-intel
ASoC: Fixes for v4.6
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mcasp davinci_mcasp_set_dai_fmt function was overriding ahclkx
input/output status that had already been set by the
davinci_mcasp_set_sysclk function. This commit removes clearing
of the ahclkx input/output status from davinci_mcasp_set_dai_fmt.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CCSR_SSI_SOR is a register that clears the TX and/or the RX fifo
on the i.MX SSI port. The fsl_ssi_trigger writes this register in
order to clear the fifo at trigger time.
However, since the CCSR_SSI_SOR register is not in the volatile list,
the caching mechanism prevented the register write in the trigger
function. This caused the fifo to not be cleared (because the value
was unchanged from the last time the register was written), and thus
causes the channels in both TDM or simple I2S mode to slip and be in
the wrong time slots on SSI restart.
This has gone unnoticed for so long because with simple stereo mode,
the consequence is that left and right are swapped, which isn't that
noticeable. However, it's catestrophic in some systems that
require the channels to be in the right slots.
Signed-off-by: Caleb Crome <caleb@crome.org>
Suggested-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Default channel map is set for 2 channels. Fix the channel map
based on runtime params to support multichannel.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel max is changed to 8 from stereo to support multichannel
capability for HDMI devices.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this patch, chmap controls are created and user space can
set the channel map.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
The patch following the machine driver changes adds the channel
map control in the hdac_hdmi codec driver.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support multichannel hdac hdmi driver registers with HDA
channel map framework. Channel count and channel slot verbs are
programmed by using the chmap helpers/ops. The channel
allocation is then programmed in the audio infoframe as per CEA
spec.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch parses ELD speaker allocation data block to find
sink's chmap capability.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_mod_call is counting its calling count to avoid unbalanced
function pair calling for error cases (ex init <-> quit).
SSI parent is now controlled as "mod" on current rsnd driver. Because of
this reason, SSI .remove function will be called twice if it was used as
SSI parent when user tried unbind. But probe/remove pair were not
counted. This patch counts probe/remove functions to avoid it.
Special thans Hiep
Reported-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bcm2835-i2s driver already has support for the S16_LE format but
that format hasn't been made available because dmaengine_pcm didn't
support packed data transfers.
bcm2835-i2s needs 16-bit left+right channel data to be packed into
a 32-bit word, the FIFO register is 32-bit only and doesn't support
16-bit access.
Now that dmaengine_pcm supports packed transfers the format can
be made available by setting the SND_DMAENGINE_PCM_DAI_FLAG_PACK flag.
No further configuration is necessary:
- snd_dmaengine_dai_dma_data.addr_width is already set to
DMA_SLAVE_BUSWIDTH_4_BYTES to force 32-bit DMA transfers
- dmaengine_pcm will pick up the S16_LE format from the DAI
configuration and make it available since it's no longer
masked out due to the PACK flag.
- there are no further corner cases to catch in hw_params,
since the channel count is fixed at 2 we always have two
16-bit stereo samples that can be transferred via 32-bit DMA
Signed-off-by: Matthias Reichl <hias@horus.com>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
dmaengine_pcm currently only supports setups where FIFO reads/writes
correspond to exactly one sample, eg 16-bit sample data is transferred
via 16-bit FIFO accesses, 32-bit data via 32-bit accesses.
This patch adds support for setups with fixed width FIFOs where
multiple samples are packed into a larger word.
For example setups with a 32-bit wide FIFO register that expect
16-bit sample transfers to be done with the left+right sample data
packed into a 32-bit word.
Support for packed transfers is controlled via the
SND_DMAENGINE_PCM_DAI_FLAG_PACK flag in snd_dmaengine_dai_dma_data.flags
If this flag is set dmaengine_pcm doesn't put any restriction on the
supported formats and sets the DMA transfer width to undefined.
This means control over the constraints is now transferred to the DAI
driver and it's responsible to provide proper configuration and
check for possible corner cases that aren't handled by the ALSA core.
Signed-off-by: Matthias Reichl <hias@horus.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If size mismatch of manifest, ABI headers or elements is found, stop
parsing topology info and return the error.
New fields may be append to the tail of ABI objects which will cause
object size to increase. If user space and kernel use different versions
of ABI, size mismatch will be detected here.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stop loading topology info if error happens when creating a widget.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS5720L/M device is a high-efficiency mono
Class-D audio power amplifier optimized for high transient power
capability to use the dynamic power headroom of small loudspeakers.
Its digital time division multiplexed (TDM) interface enables up to
16 devices to share the same bus.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a function to delete and free the contents of the alg_regions list.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure that the wm_adsp driver cleans up when the codec driver
is removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds a wm_adsp2_remove() function to ensure that memory
is freed when the driver is unloaded or shut down.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bits in the ARIZONA_CLOCK_CONTROL register only respond to writes of
a '1', a write of '0' is ignored. So there's no need to use update_bits.
We can do a simple write to set bits.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize the dma_slave_config for PCM DMA transfers,
instead of leaving it uninitialized. Keeps previous data on
the stack from giving us invalid values in uninitialized
members of the config structure.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because LRCK of TDM use High to Low as default setting, this patch
changes the TDM setting to inverse LRCK.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT298_CBJ_CTRL1(0x4f) bit 10 is needed for headset capture. It
will be turned off when "VREF" widget is on and be turned on when
bias level is ON. It is odd. And if "VREF" is turned on in bias
level is ON, RT298_CBJ_CTRL1(0x4f) bit 10 will be turned off.
This patch move the bit control from rt298_set_bias_level and
rt298_vref_event to rt298_jack_detect. So it will be turned on
once a jack is plugged in.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt298 need to reset AD filter and the ADC settings will take effort.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need to enable the clock if we are a clock master.
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Original work by Zoltan Szenczi.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds 24 bit support to the I2S driver of the BCM2835
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_find_dai() has been exported and so add the kerneldoc comments
for it.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Users have reported seeing this false warning on atom driver
[ 5.647469] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 0 doesn't have DAPM widget!!!
[ 5.661612] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 1 doesn't have DAPM widget!!!
[ 5.661646] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 2 doesn't have DAPM widget!!!
[ 5.661681] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 3 doesn't have DAPM widget!!!
[ 5.661708] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in0_0 doesn't have DAPM widget!!!
[ 5.661738] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in0_1 doesn't have DAPM widget!!!
[ 5.661771] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in1_0 doesn't have DAPM widget!!!
[ 5.661807] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in1_1 doesn't have DAPM widget!!!
This is caused when check for control is not being associated
with a dapm widget, but the check is wrong as the else case
maybe triggered when widget is not powered up, so we should
check if widget is associated before printing this message.
Tested-by: Sandeep Tayal <sandeepx.tayal@intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA doesn't know about all the different compressed audio formats,
so there is no interface to let userspace enumerate the formats that
are supported by the connected sink. Exporting the raw ELD bytes to
userspace allows an application to select the appropriate audio format
depending on the current capabilities of the connected HDMI sink device.
Usually userspace then just pretends to ALSA that the data is in one of
the raw 16-bit PCM audio formats and relies on the IEC controls to tell
the sink how to interpret the data.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This creates pcmC0D2p for the HDMI playback in the same card.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid complex string manipulations with UUID in canonical
form, use UUID in binary format.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds second I2S connection to rt5650 codec for capture path on
mt8173-rt5650 machine driver.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting up an FLL in pseudo-fractional mode it is preferred
to use a lower FRATIO if possible to give a higher reference clock
frequency. This patch swaps the two loops in arizona_calc_fratio()
so that lower FRATIOs are tried first. The decrementing loop is also
changed to start from init_ratio because the original settings might
already give a fractional value for N.K
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input mixers support routing the IN1_R pin to the Left PGA and the
IN2_L pin to the Right PGA. This patch allows for those routings.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input pins of the aic3204 have resistors inline with them. The
current code assumes that you want a 10k resistor inline with your
inputs and implements it as a simple switch. This patch creates an enum
for each pin and allows you to switch between not connected, 10k, 20k
and 40k ohm values. This more closely models the acutal aic3204 part.
These pin settings are documented in TI's SLAA557 pages 135 and 136
(http://www.ti.com/lit/ml/slaa557/slaa557.pdf).
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
When creating a FE link, the cpu_dai_name will come from topology and
dpcm will be enabled by default.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This API can be used by topology to find an existing BE dai by name
and further configure it.
Topology will also check DAI ID to avoid wrong match.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology will set the link's generic id when creating a FE link.
Device drivers can check the id for link specific initialization.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The generic ID can be used by topology:
- Toplogy can create FE links and set their ID, machine drivers will
be notified and check this ID for machine-specific init.
- Toplogy can use the ID to find existing BE & CC links and further
configure them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320AIC32x4 series supports 96ksps rates in hardware. This patch
adds the necessary PLL divider values and clock settings to the table to
make 96ksps work.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo 100S netbook has a codec controller for which there is a
driver, but doesn't know how to access the device. This adds the
necessary ACPI table for the driver to find the device.
Device (TTLV)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "10TI3100") // _HID: Hardware ID
Name (_CID, "10TI3100") // _CID: Compatible ID
Name (_DDN, "TI TLV320AIC3100 Codec Controller ") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Jan Schmidt <jan@centricular.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL function was updated to disallow 32KHz in
commit 501f72e9c5 ("ASoC: da7219: Remove support for 32KHz PLL mode"),
but set_dai_sysclk() was missed and still permits it. This patch resolves
that discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for running the tlv32x4 control channel over SPI rather than I2C.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
To prepare for abstracting adding SPI support, the I2C pieces needs to
be in its own moudle. This patch moves common probe code into aic32x4_probe
and common removal code into aic32x4_remove. It also creates a static
regmap config structure to be copied in the I2C specific driver.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec's probe function is named aic32x4_probe. This is going to
conflict with later work to implement SPI support and separate out I2S
into its own file. In line with other drivers in the tree, this function
is renamed to aic32x4_codec_probe instead.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi-codec is a platform device driver to be registered from
drivers of external HDMI encoders with I2S and/or spdif interface. The
driver in turn registers an ASoC codec for the HDMI encoder's audio
functionality.
The structures and definitions in the API header are mostly redundant
copies of similar structures in ASoC headers. This is on purpose to
avoid direct dependencies to ASoC structures in video side driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds DT support for the TI DA8xx/OMAP-L1x/AM17xx/AM18xx McBSP driver.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default, player#0 is connected to I2S/TDM TX bus.
This patch connects player#1 to I2S/TDM TX bus.
Signed-off-by: Moise Gergaud <moise.gergaud@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We request one of the DSP IRQs during CODEC probe, as such we should
free it during CODEC remove, this patch does so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The thermal warning IRQs for the speaker are requested in CODEC probe
but never freed. This patch frees them in CODEC remove.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Documentation/printk-formats.txt has
unsigned long: use %lu or %lx
size_t: use %zu or %zx
runtime->dma_bytes is of type size_t.
runtime->min_align is of type unsigned long.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Documentation/printk-formats.txt has
size_t: use %zu or %zx
runtime->dma_bytes is of type size_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
FW expects sampling rate rounded up to next higher integer value
when calculating ibs/obs. For example for 44.1k, it should be
rounded up to 45 to calculate ibs/obs.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are the changes to enable reader tdm mode:
- When TDM_ENABLE is set to 1, the i2s format should be automatically
configured. Unfortunately this is not the case (HW bug). Then, we shall
force DATA_SIZE setting.
- Compute the transfer size for tdm mode: transfer size = user frame size
- Manage tdm slots configuration given in DT.
- Refine the hw param (channels & format) according to tdm slot config.
Signed-off-by: Moise Gergaud <moise.gergaud@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
here are the changes to enable player tdm mode:
- When TDM_ENABLE is set to 1, the i2s format should be automatically
configured. Unfortunately this is not the case (HW bug). Then, we shall
force DATA_SIZE setting.
- Compute the transfer size for tdm mode: transfer size = user frame size
- Manage tdm slots configuration given in DT.
- Don't use mclk-fs when unip in tdm mode; use tdm slot config to compute
frame size and to set mclk rate.
- Refine the hw param (channels & format) according to tdm slot config.
Signed-off-by: Moise Gergaud <moise.gergaud@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS47L24 and WM1831 codecs only use the OUT4L widget so we can
skip creation of the OUT4R widget.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
acpi_dev_present() was originally named after pci_dev_present()
to signify the similarity of the two functions.
However Rafael J. Wysocki pointed out that the exported function
acpi_dev_present() is easily confused with the non-exported
acpi_device_is_present(). Additionally in ACPI parlance the term
"present" usually refers to the "device is present" bit returned
by the _STA control method, yet acpi_dev_present() merely checks
presence in the namespace. It does not invoke _STA at all, let
alone check the "device is present" bit.
As suggested by Rafael, rename the function to acpi_dev_found()
and adjust all existing call sites.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch makes Designware I2S driver use the fifo
depth value to program the fifo configuration register
instead of using hardcoded values.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we encounter an error on the DSP side whilst user-space is
waiting on the poll we should call snd_compr_fragment_elapsed,
although data is not actually available we want to wake
user-space such that the error can be propagated out
quickly. Additionally some versions of the DSP firmware are
not super consistent about actually generating an IRQ if they
encounter an error, as such we will check the DSP error status
every time we run out of available data as well, to ensure we
catch it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor out the reading of the DSP error flag into its own function to
support further improvements to the code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the original code we ended the loop with tries set to -1 instead of
zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to unmask all interrupts at I2S start. This
can cause performance issues in slower platforms.
Unmask only the interrupts for the used channels.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the system enters S3 during a playback, codec power needs to
be turned OFF during suspend and restored during resume. With
this patch the AFG node is set to D3 and codec power is turned
OFF during controller suspend call.
During resume, the codec power is left in ON state if the
playback was in progress while suspending.
Also setting power state for AFG node is optimized. With this the
loop with timeout is removed and codec_read is used instead.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_pm ops feature instead of soc pm as core assumes system
is capable of direct complete. Register with complete callback
instead of resume to synchronize with Jack notification from
display driver. This ensures correct Jack notification to user
space.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
IS_ERR_VALUE should be used only with unsigned long type,
signed types should use comparison 'ret < 0'
This patch removes such usages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes following static checker warning, by initializing the
ret to -EINVAL, as one of the code path in lpass_platform_pcm_new()
uses this variable uninitialized.
sound/soc/qcom/lpass-platform.c:555 lpass_platform_pcm_new()
error: uninitialized symbol 'ret'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The list of TAS571x registers was incomplete.
Added the missing register definitions up to the register 0x25.
Added volatile and read-only register tables into tas5711_regmap_config
and tas5717_regmap_config.
The chip has 256 registers in total. But from address 0x29 on
(0x26 to 0x28 are reserved) the register width varies between
20, 12 and 8 bytes, which the register map cannot represent.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The chip selection was relying only on DT. It was not possible to use the
driver without DT.
This adds the chip type detection from the I2C name, which
allows to use the driver from the platform driver without DT.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton DSP is mostly similar to Skylake one but with subtle
differences like no Code Load DMA and uses HDA DMA for code
loading, DSP D0 and D3 sequences are different.
These changes are comprehended by adding different DSP power up
and down handlers, and new loader ops and also adding prepare and
trigger which HDA DSP DMA requires
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add function stub for "sst_acpi_find_name_from_hid()"
when CONFIG_ACPI is not enabled so that the driver will build
successfully. This fixes the following build errors:
(loadable module)
ERROR: "sst_acpi_find_name_from_hid" [sound/soc/intel/boards/snd-soc-sst-bytcr-rt5640.ko] undefined!
(or built-in)
bytcr_rt5640.c:(.text+0x26fc52): undefined reference to `sst_acpi_find_name_from_hid'
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that this is directly user selectable it needs to care about its
dependencies.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver did not have a mute function. The amplifier was brought out of
shutdown mode (hard-mute) once for ever in probe(), which was causing
clicks and pops when altering the I2C register configuration later.
This adds the digital_mute() function. The amplifier unmute in probe()
was removed.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cs47l24 supports the audio trace firmware, this streams of audio to be
captured from the CODEC over a compressed audio channel for
analysis/debugging of audio processing firmwares.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All other debug messages talk about data on the compressed stream in
bytes except avail which is shown in words. To avoid confusion show
avail in bytes as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Firstly, we should be locking the pwr_lock when we initialise the
compressed buffer. Secondly, fixup a couple of places when we should be
pulling pointers only under the pwr_lock as they may be affected by
operations that take that lock.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When trying to use simple card with wm8962 the following probe
error happens:
wm8962 0-001a: simple-card: set_sysclk error
asoc-simple-card sound: ASoC: failed to init 202c000.ssi-wm8962: -22
asoc-simple-card sound: ASoC: failed to instantiate card -22
asoc-simple-card: probe of sound failed with error -22
In simple-card.c the snd_soc_dai_set_sysclk() function is called with
clk_id as 0, which is an invalid clock for wm8962.
Adjust the clocks source definitions in wm8962.h so that the
simple card driver can work successfully.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable dspclk holds the rate of the DSPCLK, but the variable
sysclk holds an identifier for the clock. Currently if read a
non-sensical value from the DSPCLK_DIV register we assign sysclk to
dspclk, clearly this was intended to be sysclk_rate.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error message fits well into a single line.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When regulator_bulk_enable() fails inside wm8962_runtime_resume(),
we should disable the previously enabled clock.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a menu selection text so that users can enable, disable or
mark it as module in menuconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack plug status is rechecked at resume to handle plug/unplug
in S3 when the chip has no power.
Suspend/resume callbacks are moved from the i2c dev_pm_ops to
snd_soc_codec_driver. soc_resume_deferred is a delayed work
which may trigger nau8825_set_bias_level. The bias change races
against dev_pm_ops, causing jack detection issues.
soc_resume_deferred ensures bias change and snd_soc_codec_driver
suspend/resume are sequenced correctly.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In PRE PMD of widget handler DSP resources are allocated after
the creation of DSP pipe and modules and in POST PMD DSP
resources are destroyed.
If there is any failure in pipe or module creation in PRE PMD,
pcm trigger fails and finally POST PMD gets called and DSP
resources are freed, without getting allocated.
Fixes the DSP resource de-allocation by allocating the resource
before creation of pipe and module in PRE PMD and in POST PMD,
free the resources.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module needs to be unloaded only when it is loaded successfully.
To fix this, first correct the module state sequence and set module
state to LOADED if module is loaded successfully.
When unloading the module check if module state is not in UNINIT,
then unload it.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Cc+v
-----END PGP SIGNATURE-----
Merge tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514"
* tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (291 commits)
ALSA: hda - Fix mutex deadlock at HDMI/DP hotplug
ALSA: ctl: change return value in compatibility layer so that it's the same value in core implementation
ALSA: mixart: silence an uninitialized variable warning
ALSA: usb-audio: Add sanity checks for endpoint accesses
ALSA: usb-audio: Minor code cleanup in create_fixed_stream_quirk()
ALSA: usb-audio: Fix NULL dereference in create_fixed_stream_quirk()
ALSA: hda - Limit i915 HDMI binding only for HSW and later
ALSA: hda - Fix unconditional GPIO toggle via automute
ALSA: mixart: silence unitialized variable warnings
ALSA: hda - Fixes double fault in nvhdmi_chmap_cea_alloc_validate_get_type
ALSA: intel8x0: Add clock quirk entry for AD1981B on IBM ThinkPad X41.
ALSA: hda - Add new GPU codec ID 0x10de0082 to snd-hda
ASoC: rsnd: add simplified module explanation
ASoC: hdac_hdmi: Add broxton device ID
ASoC: Intel: Bxtn: Add Broxton PCI ID
ASoC: Intel: Skylake: Move Skylake dsp ops & loader ops
ASoC: Intel: add dmabuffer to common sst_dsp
ASoC: Intel: Skylake: Unstatify skl_dsp_enable_core
ASoC: Intel: Skylake: Fix whitepsace issues
ASoC: Intel: Skylake: Move module id defines
...
The Skylake driver selects SND_HDA_I915 which causes kbuild to spew warning:
warning: (SND_SOC_INTEL_SKYLAKE) selects SND_HDA_I915 which has unmet direct dependencies
(SOUND && !M68K && !UML && SND && DRM_I915 && SND_HDA_CORE)
The SND_HDA_I915 should not be selected so drop that.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dummy component is reused for all cards so we special case and don't
bind it to any of them. This means that code like that displaying the
component widgets that tries to look at the card will crash. In the
future we will fix this by ensuring that the dummy component looks like
other components but that is invasive and so not suitable for a fix.
Instead add a special case check here.
Reported-by: Harry Pan <harry.pan@intel.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
OMAP3's McBSP2 and McBSP3 module have integrated sidetone block with
dedicated SYSCONFIG register. The sidetone is operating from the maain
McBSP module's ICLK. For normal operation the sidetone clock auto idle
support needs to be disabled when it is activated.
Note: This is not enough to avoid choppy sidetone because this AUTOIDLE
bit is controlling only the clock auto idle from the McBSP to the sidetone
block. If the McBSP_ICLK is idling, the sidetone clock is going to do the
same.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch corrects the interface adc/dac control register definition
according to datasheet.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The PCI bus takes pci_dev_get() and pci_dev_put() is also there.
So no need for drivers to invoke these. In SKL driver we were
calling pci_dev_put() only which is not right, so remove this
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Skylake driver uses i915 component APIs to talk to display.
On remove we should free up by invoking snd_hdac_i915_exit() but
that should be last thing in remove routine, so move it to last
in skl_free()
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In Skylake destructor we unmap the hardware address and then free
links and streams. The stream free accesses hardware to write to
registers and predictably causes oops.
So change the order and unmap last in destructor.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are supposed to freeup the Code loader DMA allocation and
ensure all interrupts are disabled before we disable dsp cores.
So invoke these to ensure DSP shuts down properly.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On driver removal we should ask the core to remove the device
objects as well, so invoke snd_hdac_ext_bus_device_remove() in
remove.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5616 codec registers itself as an i2c driver, but can
be enabled even when i2c is turned off, which leads to a build
error:
codecs/rt5616.c:1419:1: error: data definition has no type or storage class [-Werror]
module_i2c_driver(rt5616_i2c_driver);
This adds an explicit Kconfig dependency, like the other codec
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 288bc356a8 ("ASoC: rt5616: allow to build with CONFIG_SND_SOC_RT5616")
Signed-off-by: Mark Brown <broonie@kernel.org>
This has been an extremely quiet release for the regulator API, aside
from bugfixes and small enhancements the only thing that really stands
out are the new drivers for Action Semiconductors ACT8945A, HiSilicon
HI665x, and the Maxim MAX20024 and MAX77620.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW58EWAAoJECTWi3JdVIfQMGMH/1v4ojMy0X/yPlFk/523u7uq
6ZJQ4zSTPyv0ccR+hsDjZ81BmM/vATrnQOllvTSwfnGMcs5amE3/9EhzdF5EciCB
8gUff/GfugXNqpVgpfYYfPhbQVTGllOFnZPmXsLx2dGlu094i69f4fZtoJCFlkmo
5c0L5Fnkt4w5XtFAA6ILuRtpwZ4jfJZ3VFKrtYwkgLcKw9GgSEqhVKvTPfkNqtjg
hzEl2P2K/Ug2uTqeZusKH30Sa1J7MW4B+C9dUVyTRB29+uA60y0foGTQjW9uCzEi
l1sqY9VDSKp9WwnshVrgVFViAhkrA7fWl4qaC/EDe7avvbh5SBpR/+gjZbmdRJU=
=jEl0
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been an extremely quiet release for the regulator API, aside
from bugfixes and small enhancements the only thing that really stands
out are the new drivers for Action Semiconductors ACT8945A, HiSilicon
HI665x, and the Maxim MAX20024 and MAX77620"
* tag 'regulator-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (46 commits)
regulator: pwm: Add support to have multiple instance of pwm regulator
regulator: pwm: Fix calculation of voltage-to-duty cycle
regulator: of: Use of_property_read_u32() for reading min/max
regulator: pv88060: fix incorrect clear of event register
regulator: pv88090: fix incorrect clear of event register
regulator: max77620: Add support to configure active-discharge
regulator: core: Add support for active-discharge configuration
regulator: helper: Add helper to configure active-discharge using regmap
regulator: core: Add support for active-discharge configuration
regulator: DT: Add DT property for active-discharge configuration
regulator: act8865: Specify fixed voltage of 3.3V for ACT8600's REG9
regulator: act8865: Rename platform_data field to init_data
regulator: act8865: Remove "static" from local variable
ASoC: cs4271: add regulator consumer support
regulator: max77620: Remove duplicate module alias
regulator: max77620: Eliminate duplicate code
regulator: max77620: Remove unused fields
regulator: core: fix crash in error path of regulator_register
regulator: core: Request GPIO before creating sysfs entries
regulator: gpio: don't print error on EPROBE_DEFER
...
gcc warns about the possibilty of accessing a property read from
devicetree in cs35l32_i2c_probe() when it has not been initialized
because CONFIG_OF is disabled:
sound/soc/codecs/cs35l32.c: In function 'cs35l32_i2c_probe':
sound/soc/codecs/cs35l32.c:278:2: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
The code is actually correct because it checks the dev->of_node
variable first and we know this is NULL here when CONFIG_OF
is disabled, but Russell King noticed that it's broken when
we probe the device using DT, and the properties are absent.
The code already has some checking for incorrect values, and
I keep that checking unchanged here, but add an additional
check for an error returned by the property accessor functions
that now gets handled the same way as incorrect data in the
properties.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull dma_*_writecombine rename from Ingo Molnar:
"Rename dma_*_writecombine() to dma_*_wc()
This is a tree-wide API rename, to move the dma_*() write-combining
APIs closer in name to their usual API families. (The old API names
are kept as compatibility wrappers to not introduce extra breakage.)
The patch was Coccinelle generated"
* 'mm-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dma, mm/pat: Rename dma_*_writecombine() to dma_*_wc()
The main thing in terms of the core this time around has been some
additional framework work for dynamic topologies (though we *still*
don't appear to have a stable ABI for the topology code, it's probably
worth considering if this will ever happen...). Otherwise the work has
almost all been in the drivers:
- HDMI support for Sky Lake, along with other fixes and enhancements
for the Intel drivers.
- Lots of improvements to the Renesas drivers.
- Capture support for Qualcomm drivers.
- Support for TI DaVinci DRA7xxx devices.
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs.
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW5qP+AAoJECTWi3JdVIfQJhAH/RKv268gjE07uJ8jeGAT7uY4
XM19VmUl7ZOlphctfr/I+1hRwo+mgGN4LSfKnXxsPk9Uq/WJUok4D7MjDN33jeX/
heK9WAO8zXkgi9n2lhGI/z9uE76kPA/Qw0aEYcbmA6bDc4GF3AKphnByh6kDShtE
BfblofsFaDywA09XQ2lh3wW0rZtJ51tQUeOi35UADyEPzQetzN+xiY85Bkia5BEt
Yjp37nLJET8Gk0r9snE2MpACUkEyw7CiPXCjkK47npia41LVnTarZAq5+JmfKygg
YV2EnC3AFYthhjZPfmO1usI2vJVwkN40nGrKipH2QX08TanK8r2qiTsmGADNX4E=
=0/1R
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.6
The main thing in terms of the core this time around has been some
additional framework work for dynamic topologies (though we *still*
don't appear to have a stable ABI for the topology code, it's probably
worth considering if this will ever happen...). Otherwise the work has
almost all been in the drivers:
- HDMI support for Sky Lake, along with other fixes and enhancements
for the Intel drivers.
- Lots of improvements to the Renesas drivers.
- Capture support for Qualcomm drivers.
- Support for TI DaVinci DRA7xxx devices.
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs.
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514.
Renesas sound driver user needs to read its datasheet when create DT.
But it is difficult to understand, because it has many modules
(SRC/CTU/MIX/DVC/SSIU/SSI/AudioDMAC/AudioDMACperiperi),
and many features (Asynchronous/Synchronous mode on SRC, CTU matrix,
DVC volume settings feature, Multi-SSI/TDM-SSI, etc).
This patch adds simplified explanation to help setting/understanding.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton HDMI codec is similar to Skylake so add the device ID
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton is an Intel SoC which sports a DSP and system is quite
like Skylake. So add this ID in Skylake driver
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code loading for Skylake and other platforms is different, so
add a dsp_ops and a loader_ops which can be defined for each
platform.
Move the dsp init, cleanup and loader ops (alloc and free dma) to
these ops
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton uses HDA DMA so needs to keep dmab in the driver context
so add it
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function skl_dsp_enable_core will be called by other parts of
driver so this can no longer be a static function.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some double whitespaces issues existed in driver, so fix them up.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module ID defines are common to other platforms so can be
reused if moved to a common driver header so move it
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reduce pop noise in power up and down sequence when playback.
The DAPM widgets graph is reconstructed to ensure the
register write sequence at playback matches exactly to the
v5 clickless sequence provided by Nuvoton.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
While building m32r allmodconfig the build failed with:
ERROR: "bad_dma_ops" [sound/soc/qcom/snd-soc-lpass-platform.ko] undefined!
ERROR: "dma_common_mmap" [sound/soc/qcom/snd-soc-lpass-platform.ko] undefined!
To satisfy the dependency CONFIG_SND_SOC_LPASS_PLATFORM should depend
on HAS_DMA.
Some other configs also needs the dependency on HAS_DMA as they are
directly or indirectly selecting SND_SOC_LPASS_PLATFORM.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of depending on individual SoCs make the edma-pcm depend on the eDMA
dmaengine driver (TI_EDMA).
Update the help text and add DRA7xx family since they have eDMA integrated
as well along with sDMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case when the dai format is set via the dai_link the format
configuration happens once when the links are probed. If the McASP lose
context after this, the information will be lost and McASP will not going
to work correctly.
To overcome this issue, we save the fmt and set it within hw_params as
well.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 44029e9e1290 ("ASoC: wm_adsp: wm_coeff_{read|write}_control should use passed length")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio infoframe used incorrect buffer, so fix it.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are getting build warning about:
sound/soc/codecs/rt5640.c:1892:11: warning: unused variable 'dai_sel'
The use of the variable was removed but the variable itself was not
removed.
Fixes: c467fc0e01 ("ASoC: rt5640: Set PLL src according to source")
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
CMD.out should use same as SRC.out for TIMSEL settings,
but it cares Playback case only. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC has Sync/Async mode, and it can't use Sync mode when Capture
with CMD. In Async mode, it needs to care about in/out SRC rate
for settings, but current driver supporting Playback case only.
This patch supports Capture case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC will convert rate, and then, CMD and SSI want to know its
rate (= SRC.in / SRC.out) for each purpose.
Current driver is supporting only Playback, but SRC+Capture support
needs more flexibility.
This patch adds rsnd_src_get_in/out_rate() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_enable_sync_convert() is for checking, not for setting.
In order to avoid confusion, this patch renamed it to
rsnd_src_sync_is_enabled()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce confusion, SRC uses "mod" instead of "src"
as function parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC sync mode needs to control its clock (= for in/out). 1st but codec
side clock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can't use SRC Synchronous convert when Capture if it uses CMD,
because no one provide out side clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAC1/2 power is for both DACs and related mixer/mux. Add SUPPLY
type widgets to support it.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5640_set_dai_pll set pll source according to given source and
dai id. However, the pll source should be set according to given
source only.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes coccicheck report:
Unneeded variable: "ret". Return "0" on line 2817
Remove unneccesary variable ret created to return zero.
Signed-off-by: Rajan Vaja <rajan.vaja@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the necessary device tree compatible string to allow DT
probing.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
This should be more robust to future changes than adressing
array entries by index number.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds CTU (= Channel Transfer Unit) support on
Renesas R-Car sound driver.
It can Down/Up mixing and splitter. You need to check R-Car datasheet
especially CTUn_CPMDR/CTUn_SV0xR/CTUn_SV1xR/CTUn_SV2xR/CTUn_SV3xR
for setting parameter.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI is supporting Normal SSI/Multi mode SSI/TDM mode SSI
and its behavior is based on input channels.
This input channel might be converted by CTU,
and SSI needs to be Multi SSI mode / TDM SSI mode if 6ch input
EX) 6ch input, CTU for 2ch, playback
6ch 6ch 2ch 2ch 2ch 2ch
-> SRC -> CTU -> MIX -> DVC -> SSIU -> SSI
EX) 6ch input, no CTU, Multi SSI, playback
6ch 6ch 6ch 6ch 6ch 2ch
-> SRC -> CTU -> MIX -> DVC -> SSIU -> SSI0/SSI1/SSI2
Current driver is using rsnd_get_adinr_chan() / rsnd_get_slot_width()
for this purpose, but it is complicated enough without meaning.
This patch adds new rsnd_runtime_channel_xxx() which is caring
CTU/Multi SSI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Renesas R-Car sound CTU (= Channel Transfer Unit)
very basic support, but not yet enough feature at this point.
Because CTU support needs more complex channel function for
each modules.
To avoid complex patch reviewing, this patch picked up very basic
part only.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound device has CTU (= Channel Transfer Unit), and
sound card needs its support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some CHT-T platforms make use of the Realtek RT5640 codec. Make use
of the machine driver developed for Baytrail.
Tested on Tronsmart Ara X5.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove hard-coded generation of codec name, use translation routine
to avoid issues with codec name not matching what the ACPI subsystem
registered
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BIOS vendors sometimes declare multiple devices in the DSDT
table that all refer to the same HID. This is not very smart
but not illegal as long as only one device reports present with
the _STA method. The ACPI subsystem tracks each device with an
extension, e.g. 10EC5640:00 and 10EC5640:01
In the ASoC machine driver, the DAI codec name needs to refer to the
ACPI device that reported present, e.g. "i2c-10EC5640:01". The
extension will vary depending on how the BIOS is written and which
ACPI device is activated.
This patch adds a translation function that provides the codec
name from the ACPI HID to avoid any hard-coded values in the
machine driver.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BIOS vendors typically list multiple audio codecs in the DSDT
table and enable the relevant one by changing the return value
of the _STA method.
With the current code, all devices are reported by
acpi_dev_present(), regardless of the _STA return values. This
causes errors on probe with the wrong machine driver being loaded.
This patch essentially reverts 'commit 6f08cbdaac
("ASoC: Intel: Use acpi_dev_present()")' and adds code to
force the evaluation of the _STA method.
A better solution might be to make sure the ACPI subsystem only
reports devices with a _STA value of 0xf but apparently it's
problematic so dealing with this in the audio subsystem directly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch add compatible for rk3366/rk3368/rk3399 spdif,
these three spdifs share the same type.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While building we were getting build warning about:
sound/soc/codecs/pcm3168a.c:403:21: warning: variable 'channels' set but
not used
The variable channels were being assigned some value but that was never
reused.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rockchip spdif driver uses SIMPLE_DEV_PM_OPS to conditionally
set its power management functions, but we get a warning
about rk_spdif_runtime_resume being unused when CONFIG_PM is not
set:
sound/soc/rockchip/rockchip_spdif.c:67:12: error: 'rk_spdif_runtime_resume' defined but not used [-Werror=unused-function]
This adds a __maybe_unused annotation so the compiler knows
it can silently drop it instead of warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes that hasn't built the rt5616 driver with
'CONFIG_SND_SOC_RT5616=y' in .config.
The tristate is the prompt on the 'make menuconfig',
in other words, that can't show the prompt and select it
if we don't say what's the tristate.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cpu_dai id always equals 0, can't distinguish the
different SSC. Use platform_device id to record
and distinguish the different SSC.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the DPCM based machine driver with rt5650 and rt5514.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some R-Car sound requests picky register access which needs *force*
register write.
Some status register needs to set 1 to clear status, but we might
read 1 from its register. In such case, current regmap does nothing
and driver will be forever loop
To reduce code complexity, this patch uses regmap _force_
function for all register access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IVI loop is removed in skl_nau88l25_ssm4567 machine as we
enable this path thru DAPM graph using the PCM device and not
thru loop
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can enable the IVI feedback path by connecting Left/Right
speaker sensors (codec) to ssp0 Rx (soc-dsp). This way aDSP gets
feedback data from codec to DSP algorithms
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The blob query for BE skl_tplg_update_be_blob() was not using
right values for direction for blob query, so fix that.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware ctls like "DSP1 Firmware" in wm_adsp codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"Speaker Mode "ctl in wm9081 codec driver is enum, while the current
driver accesses wrongly via value.integer.value[]. They have to be
via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DSP1 EQ Mode" and "DSP2 EQ Mode" ctls in wm8996 codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DRC Mode like "AIF1DRC1 Mode" and EQ Mode like "AIF1.1 EQ Mode" in
wm8994 codec driver are enum ctls, while the current driver accesses
wrongly via value.integer.value[]. They have to be via
value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"Equalizer Function" ctl in wm8985 codec driver is enum, while the
current driver accesses wrongly via value.integer.value[]. They have
to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Equalizer Function" ctl in wm8983 codec driver is enum, while the
current driver accesses wrongly via value.integer.value[]. They have
to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"MBC Mode", "VSS Mode", "VSS HPF Mode" and "Enhanced EQ Mode" ctls in
wm8958 codec driver are enum, while the current driver accesses
wrongly via value.integer.value[]. They have to be via
value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"DRC Mode" and "EQ Mode" ctls in wm8904 codec driver are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DAI Mode" ctl in wm8753 codec driver is enum, while the current
driver accesses wrongly via value.integer.value[]. They have to be
via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Codec Mode" and "Audio Switch" ctls in wl1273 codec driver are enum,
while the current driver accesses wrongly via value.integer.value[].
They have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"FIFO Mode" ctl in tlv320dac33 codec driver is enum, while the current
driver accesses wrongly via value.integer.value[]. They have to be
via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Biquad1 Mode" and "Biquad2 Mode" ctls in max98095 codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"EQ1 Mode" and "EQ2 Mode" ctls in max98088 codec driver are enum,
while the current driver accesses wrongly via value.integer.value[].
They have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Sidetone Status" and "ANC Status" ctls in ab8500 codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DAC1 High Pass Filter Mode" & co in da732x codec driver are enum,
while the current driver accesses wrongly via value.integer.value[].
They have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"PCM channel mixer" ctl in cs42l51 codec driver is enum, while the
current driver accesses wrongly via value.integer.value[]. They have
to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Playback Switch" and "Lineout Mux" ctls in medfld machine driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Speaker Function", "Input Select" and "Jack Function" ctls in rx51
driver are enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function", "Speaker Function" and "Input Select" ctls in n810
driver are enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function" and "Speaker Function" ctls in tosa are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function" and "Speaker Function" ctls in spitz are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function" and "Speaker Function" ctls in poodle are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Input Select" ctl in magician driver is an enum, while the current
driver accesses wrongly via value.integer.value[]. They have to be
via value.enumerated.item[] instead.
(Meanwhile "Headphone Switch" and "Speaker Switch" are boolean, so
they should stay to access via value.integer.value[] as is.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function" and "Speaker Function" ctls in corgi are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dapm_dai_link_get() and _put() access the associated ctl
values as value.integer.value[]. However, this is an enum ctl, and it
has to be accessed via value.enumerated.item[]. The former is long
while the latter is unsigned int, so they don't align.
Fixes: c66150824b ('ASoC: dapm: add code to configure dai link parameters')
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable cmd_id is only assigned some value and is never used.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cs4271 has three power domains: vd, vl and va.
Enable them all, as long as the codec is in use.
While at it, factored out the reset code into its own function.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add these widgets to allow another path from I2S input.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We cannot use strcpy() to write to a const char * location. This is
causing a 'BUG: unable to handle kernel paging request' error at boot
when using the cht-bsw-rt5645 driver.
With this patch we also fix a wrong indexing in the driver where the
codec_name of the wrong dai_link is being overwritten.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To improve I2S flow, this patch removes soft reset and adds second
I2S clock to use.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As pointed out by Zhangfei Gao, the sspa_div variable in
brownstone_wm8994_hw_params() is completely unused, so as a cleanup
following a prior patch, this removes both the variable and the division.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Headphone needs enough delay time before unmuting for avoiding pop sound.
We extend the delay time to make sure headphone doesn't pop.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When playing audio through headphone, headphone makes pop noise if system
resumes from S3 to S0. We modify the sequence of writing register for
avoiding pop sound.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
