Set the maximum segment size, since the hardware can do transfers larger
than the default 64 KiB returned by dma_get_max_seg_size().
The maximum segment size is limited by the 24-bit transfer count field
in DMA descriptors. The number of bytes is equal to the transfer count
times the transfer size unit, which is selected by the driver based on
the DMA buffer address and length of the transfer. The size unit can be
as small as 1 byte, so set the maximum segment size to 2^24-1 bytes to
ensure the transfer count will not overflow regardless of the size unit
selected by the driver.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220411153618.49876-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For some devices with only half-duplex capabilities, it doesn't make
much sense to use one DMA channel per direction, as both channels will
never be active at the same time.
Add support for bidirectional I/O on DMA channels. The client drivers
can then request a "tx-rx" DMA channel which will be used for both
directions.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211206174259.68133-7-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4760 and JZ4760B SoCs have two regular DMA controllers with 6
channels each. They also have an extra DMA controller named MDMA
with only 2 channels, that only supports memcpy operations, and one
named BDMA with only 3 channels, that is mostly used for transfers
between memories and the BCH controller.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211206174259.68133-5-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4760 SoC has a hardware problem with chan0 not enabling properly
if it's enabled before chan1, after a reset (works fine afterwards).
This is worked around in the probe function by just enabling then
disabling chan1.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211206174259.68133-4-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Total amount of SG list entries executed in a single burst is limited by
the number of available DMA descriptors.
This information is useful for device drivers utilizing this DMA engine.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210829195805.148964-1-contact@artur-rojek.eu
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the JZ4760 and JZ4760B SoCs.
Both SoCs have only 5 DMA channels per chip. The JZ4760B introduced the
DCKES/DCKEC registers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210120105322.16116-2-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/dma-jz4780.c:1031:34: warning:
‘jz4780_dma_dt_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The jz4780_dma_tx_status() function would check if a channel's cookie
state was set to 'completed', and if not, it would enter the critical
section. However, in that time frame, the jz4780_dma_chan_irq() function
was able to set the cookie to 'completed', and clear the jzchan->vchan
pointer, which was deferenced in the critical section of the first
function.
Fix this race by checking the channel's cookie state after entering the
critical function and not before.
Fixes: d894fc6046 ("dmaengine: jz4780: add driver for the Ingenic JZ4780 DMA controller")
Cc: stable@vger.kernel.org # v4.0
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Link: https://lore.kernel.org/r/20201004140307.885556-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In probe, IRQ is requested before zchan->id is initialized which can be
read in the irq handler. Hence, shift request irq after other initializations
complete.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200821034423.12713-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Core:
- Support for dynamic channels
- Removal of various slave wrappers
- Make few slave request APIs as private to dmaengine
- Symlinks between channels and slaves
- Support for hotplug of controllers
- Support for metadata_ops for dma_async_tx_descriptor
- Reporting DMA cached data amount
- Virtual dma channel locking updates
- New drivers/device/feature support support:
- Driver for Intel data accelerators
- Driver for TI K3 UDMA
- Driver for PLX DMA engine
- Driver for hisilicon Kunpeng DMA engine
- Support for eDMA support for QorIQ LS1028A in fsl edma driver
- Support for cyclic dma in sun4i driver
- Support for X1830 in JZ4780 driver
-----BEGIN PGP SIGNATURE-----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=mv1v
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have a bunch of core changes to support dynamic channels,
hotplug of controllers, new apis for metadata ops etc along with new
drivers for Intel data accelerators, TI K3 UDMA, PLX DMA engine and
hisilicon Kunpeng DMA engine. Also usual assorted updates to drivers.
Core:
- Support for dynamic channels
- Removal of various slave wrappers
- Make few slave request APIs as private to dmaengine
- Symlinks between channels and slaves
- Support for hotplug of controllers
- Support for metadata_ops for dma_async_tx_descriptor
- Reporting DMA cached data amount
- Virtual dma channel locking updates
New drivers/device/feature support support:
- Driver for Intel data accelerators
- Driver for TI K3 UDMA
- Driver for PLX DMA engine
- Driver for hisilicon Kunpeng DMA engine
- Support for eDMA support for QorIQ LS1028A in fsl edma driver
- Support for cyclic dma in sun4i driver
- Support for X1830 in JZ4780 driver"
* tag 'dmaengine-5.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (62 commits)
dmaengine: Create symlinks between DMA channels and slaves
dmaengine: hisilicon: Add Kunpeng DMA engine support
dmaengine: idxd: add char driver to expose submission portal to userland
dmaengine: idxd: connect idxd to dmaengine subsystem
dmaengine: idxd: add descriptor manipulation routines
dmaengine: idxd: add sysfs ABI for idxd driver
dmaengine: idxd: add configuration component of driver
dmaengine: idxd: Init and probe for Intel data accelerators
dmaengine: add support to dynamic register/unregister of channels
dmaengine: break out channel registration
x86/asm: add iosubmit_cmds512() based on MOVDIR64B CPU instruction
dmaengine: ti: k3-udma: fix spelling mistake "limted" -> "limited"
dmaengine: s3c24xx-dma: fix spelling mistake "to" -> "too"
dmaengine: Move dma_get_{,any_}slave_channel() to private dmaengine.h
dmaengine: Remove dma_request_slave_channel_compat() wrapper
dmaengine: Remove dma_device_satisfies_mask() wrapper
dt-bindings: fsl-imx-sdma: Add i.MX8MM/i.MX8MN/i.MX8MP compatible string
dmaengine: zynqmp_dma: fix burst length configuration
dmaengine: sun4i: Add support for cyclic requests with dedicated DMA
dmaengine: fsl-qdma: fix duplicated argument to &&
...
It turns out that the JZ4725B displays the same buggy behaviour as the
JZ4740 that was described in commit f4c255f1a7 ("dmaengine: dma-jz4780:
Break descriptor chains on JZ4740").
Work around it by using the same workaround previously used for the
JZ4740.
Fixes commit f4c255f1a7 ("dmaengine: dma-jz4780: Break descriptor
chains on JZ4740")
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20191210165545.59690-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The remove misses to disable and unprepare jzdma->clk.
Add a call to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20191104161622.11758-1-hslester96@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify this function implementation a bit by using
a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/5dd19f28-349a-4957-ea3a-6aebbd7c97e2@web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-11-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current driver works perfectly fine on every generation of the
JZ47xx SoCs, except on the JZ4740.
There, when hardware descriptors are chained together (with the LINK
bit set), the next descriptor isn't automatically fetched as it should -
instead, an interrupt is raised, even if the TIE bit (Transfer Interrupt
Enable) bit is cleared. When it happens, the DMA transfer seems to be
stopped (it doesn't chain), and it's uncertain how many bytes have
actually been transferred.
Until somebody smarter than me can figure out how to make chained
descriptors work on the JZ4740, we now disable chained descriptors on
that particular SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20190714215504.10877-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Add support in dmaengine core to do device node checks for DT devices and
update bunch of drivers to use that and remove open coding from drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
-----BEGIN PGP SIGNATURE-----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=R+aC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Add support in dmaengine core to do device node checks for DT devices
and update bunch of drivers to use that and remove open coding from
drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
* tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: Revert "dmaengine: fsl-edma: add i.mx7ulp edma2 version support"
dmaengine: at_xdmac: check for non-empty xfers_list before invoking callback
Documentation: dmaengine: clean up description of dmatest usage
dmaengine: tegra210-adma: remove PM_CLK dependency
dmaengine: fsl-edma: add i.mx7ulp edma2 version support
dt-bindings: dma: fsl-edma: add new i.mx7ulp-edma
dmaengine: fsl-edma-common: version check for v2 instead
dmaengine: fsl-edma-common: move dmamux register to another single function
dmaengine: fsl-edma: add drvdata for fsl-edma
dmaengine: Revert "dmaengine: fsl-edma: support little endian for edma driver"
dmaengine: rcar-dmac: Reject zero-length slave DMA requests
dmaengine: dw: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw-edma: fix semicolon.cocci warnings
dmaengine: sh: usb-dmac: Use [] to denote a flexible array member
dmaengine: dmatest: timeout value of -1 should specify infinite wait
dmaengine: dw: Distinguish ->remove() between DW and iDMA 32-bit
dmaengine: fsl-edma: support little endian for edma driver
dmaengine: hsu: Revert "set HSU_CH_MTSR to memory width"
dmagengine: pl330: add code to get reset property
dt-bindings: pl330: document the optional resets property
...
The "pending" variable was a u32 but we cast it to an unsigned long
pointer when we do the for_each_set_bit() loop. The problem is that on
big endian 64bit systems that results in an out of bounds read.
Fixes: 4e4106f5e9 ("dmaengine: jz4780: Fix transfers being ACKed too soon")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The fixes for this round are in drivers:
- jz4780 transfer fix for acking descriptors early
- fsl-qdma: clean registers on error
- dw-axi-dmac: null pointer dereference fix
- mediatek-cqdma: fix sleeping in atomic context
- tegra210-adma: fix bunch os issues like crashing in driver
probe, channel FIFO configuration etc.
- sprd: Fixes for possible crash on descriptor status, block
length overflow. For 2-stage transfer fix incorrect start,
configuration and interrupt handling.
-----BEGIN PGP SIGNATURE-----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=Ca0d
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-5.2-rc4' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
- jz4780 transfer fix for acking descriptors early
- fsl-qdma: clean registers on error
- dw-axi-dmac: null pointer dereference fix
- mediatek-cqdma: fix sleeping in atomic context
- tegra210-adma: fix bunch os issues like crashing in driver probe,
channel FIFO configuration etc.
- sprd: Fixes for possible crash on descriptor status, block length
overflow. For 2-stage transfer fix incorrect start, configuration and
interrupt handling.
* tag 'dmaengine-fix-5.2-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sprd: Add interrupt support for 2-stage transfer
dmaengine: sprd: Fix the right place to configure 2-stage transfer
dmaengine: sprd: Fix block length overflow
dmaengine: sprd: Fix the incorrect start for 2-stage destination channels
dmaengine: sprd: Add validation of current descriptor in irq handler
dmaengine: sprd: Fix the possible crash when getting descriptor status
dmaengine: tegra210-adma: Fix spelling
dmaengine: tegra210-adma: Fix channel FIFO configuration
dmaengine: tegra210-adma: Fix crash during probe
dmaengine: mediatek-cqdma: sleeping in atomic context
dmaengine: dw-axi-dmac: fix null dereference when pointer first is null
dmaengine: fsl-qdma: Add improvement
dmaengine: jz4780: Fix transfers being ACKed too soon
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let the DMA engine core do the device node validation instead of drivers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a multi-descriptor DMA transfer is in progress, the "IRQ pending"
flag will apparently be set for that channel as soon as the last
descriptor loads, way before the IRQ actually happens. This behaviour
has been observed on the JZ4725B, but maybe other SoCs are affected.
In the case where another DMA transfer is running into completion on a
separate channel, the IRQ handler would then run the completion handler
for our previous channel even if the transfer didn't actually finish.
Fix this by checking in the completion handler that we're indeed done;
if not the interrupted DMA transfer will simply be resumed.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use SPDX license notifier instead of plain text in the header.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is the standard method provided by dmaengine header.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Func jz4780_dma_desc_residue() expects the index to the next hw
descriptor as its last parameter. Caller func jz4780_dma_tx_status(),
however, applied modulus before passing it. When the current hw
descriptor was last in the list, the index passed became zero.
The resulting excess of reported residue especially caused problems
with cyclic DMA transfer clients, i.e. ALSA AIC audio output, which
rely on this for determining current DMA location within buffer.
Combined with the recent and related residue-reporting fixes, spurious
ALSA audio underruns on jz4770 hardware are now fixed.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Normally, we wouldn't set the channel transfer count register directly
when using descriptor-driven transfers. However, there is no harm in
doing so, and it allows jz4780_dma_desc_residue() to report the correct
residue of an ongoing transfer, no matter when it is called.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simple cleanup, no changes to actual logic here.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 'dtc' word in jz DMA descriptors contains two fields: The
lowest 24 bits are the transfer count, and upper 8 bits are the DOA
offset to next descriptor. The upper 8 bits are now correctly masked
off when computing residue in jz4780_dma_desc_residue(). Note that
reads of the DTCn hardware reg are automatically masked this way.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With the fast DMA bit set, the DMA will transfer twice as much data
per clock period to the AIC, so there is little point not to set it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4725B has one DMA core starring six DMA channels.
As for the JZ4770, each DMA channel's clock can be enabled with
a register write, the difference here being that once started, it
is not possible to turn it off.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4740 SoC has a single DMA core starring six DMA channels.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4770 SoC has two DMA cores, each one featuring six DMA channels.
The major change is that each channel's clock can be enabled or disabled
through register writes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The only information we use in the 8-word version of the hardware DMA
descriptor that is not present in the 4-word version is the transfer
type, aka. the ID of the source or recipient device.
Since the transfer type will never change for a DMA channel in use,
we can just set it once for all in the corresponding DMA register
before starting any transfer.
This has several benefits:
* the driver will handle twice as many hardware DMA descriptors;
* the driver is closer to support the JZ4740, which only supports 4-word
hardware DMA descriptors;
* the JZ4770 SoC needs the transfer type to be set in the corresponding
DMA register anyway, even if 8-word descriptors are in use.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The register area of the JZ4780 DMA core can be split into different
sections for different purposes:
* one set of registers is used to perform actions at the DMA core level,
that will generally affect all channels;
* one set of registers per DMA channel, to perform actions at the DMA
channel level, that will only affect the channel in question.
The problem rises when trying to support new versions of the JZ47xx
Ingenic SoC. For instance, the JZ4770 has two DMA cores, each one
with six DMA channels, and the register sets are interleaved:
<DMA0 chan regs> <DMA1 chan regs> <DMA0 ctrl regs> <DMA1 ctrl regs>
By using one memory resource for the channel-specific registers and
one memory resource for the core-specific registers, we can support
the JZ4770, by initializing the driver once per DMA core with different
addresses.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As part of the work to support various other Ingenic JZ47xx SoC versions,
which don't feature the same number of DMA channels per core, we now
deduce the number of DMA channels available from the devicetree
compatible string.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver calls clk_get() with the clock name set to NULL, which means
that the driver could only work when probed from devicetree. From now
on, we explicitly require the driver to be probed from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To avoid race with vchan_complete, use the race free way to terminate
running transfer.
Implement the device_synchronize callback to make sure that the terminated
descriptor is freed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In two cases when jz4780_dma_setup_hwdesc fails, there is a memory
leak on the allocated desc and associated DMA pools on the error
exit return path. Fix this by free'ing the resources before
returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sparse complains:
drivers/dma/dma-jz4780.c:399:32: warning: symbol
'jz4780_dma_prep_dma_memcpy' was not declared. Should it be static?
So make this static
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Tasklets may have been scheduled as a result of an earlier interrupt
that could still be running. Kill them before unregistering the
device.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We must explicitly free the IRQ before the device is unregistered in
case any device interrupt still occurs, so there's no point in using
the managed variations of the IRQ functions. Change to the regular
versions.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When scanning for a free DMA channel, the filter function should ensure
that the channel is on the controller that it was requested to be on in
the DT.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When the DT requests a specific channel to use it is not necesssary
to scan through all DMA channels in the system. Just return the
requested channel using dma_get_slave_channel().
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are a some signedness bugs such as testing for < 0 on unsigned
return values. Additionally there are some cases where functions which
should return NULL on error actually return a PTR_ERR value which can
result in oopses on error. Fix these issues.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
