Commit fb9a307d11 ("bpf: Allow CGROUP_SKB eBPF program to
access sk_buff") enabled programs of BPF_PROG_TYPE_CGROUP_SKB
type to use ld_abs/ind instructions. However, at this point,
we cannot use them, since offsets relative to SKF_LL_OFF will
end up pointing skb_mac_header(skb) out of bounds since in the
egress path it is not yet set at that point in time, but only
after __dev_queue_xmit() did a general reset on the mac header.
bpf_internal_load_pointer_neg_helper() will then end up reading
data from a wrong offset.
BPF_PROG_TYPE_CGROUP_SKB programs can use bpf_skb_load_bytes()
already to access packet data, which is also more flexible than
the insns carried over from cBPF.
Fixes: fb9a307d11 ("bpf: Allow CGROUP_SKB eBPF program to access sk_buff")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single BPF_OBJ_GET_INFO_BY_FD cmd is used to obtain the info
for both bpf_prog and bpf_map. The kernel can figure out the
fd is associated with a bpf_prog or bpf_map.
The suggested struct bpf_prog_info and struct bpf_map_info are
not meant to be a complete list and it is not the goal of this patch.
New fields can be added in the future patch.
The focus of this patch is to create the interface,
BPF_OBJ_GET_INFO_BY_FD cmd for exposing the bpf_prog's and
bpf_map's info.
The obj's info, which will be extended (and get bigger) over time, is
separated from the bpf_attr to avoid bloating the bpf_attr.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add BPF_MAP_GET_FD_BY_ID command to allow user to get a fd
from a bpf_map's ID.
bpf_map_inc_not_zero() is added and is called with map_idr_lock
held.
__bpf_map_put() is also added which has the 'bool do_idr_lock'
param to decide if the map_idr_lock should be acquired when
freeing the map->id.
In the error path of bpf_map_inc_not_zero(), it may have to
call __bpf_map_put(map, false) which does not need
to take the map_idr_lock when freeing the map->id.
It is currently limited to CAP_SYS_ADMIN which we can
consider to lift it in followup patches.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add BPF_PROG_GET_FD_BY_ID command to allow user to get a fd
from a bpf_prog's ID.
bpf_prog_inc_not_zero() is added and is called with prog_idr_lock
held.
__bpf_prog_put() is also added which has the 'bool do_idr_lock'
param to decide if the prog_idr_lock should be acquired when
freeing the prog->id.
In the error path of bpf_prog_inc_not_zero(), it may have to
call __bpf_prog_put(map, false) which does not need
to take the prog_idr_lock when freeing the prog->id.
It is currently limited to CAP_SYS_ADMIN which we can
consider to lift it in followup patches.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds BPF_PROG_GET_NEXT_ID and BPF_MAP_GET_NEXT_ID
to allow userspace to iterate all bpf_prog IDs and bpf_map IDs.
The API is trying to be consistent with the existing
BPF_MAP_GET_NEXT_KEY.
It is currently limited to CAP_SYS_ADMIN which we can
consider to lift it in followup patches.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generates an unique ID for each created bpf_map.
The approach is similar to the earlier patch for bpf_prog ID.
It is worth to note that the bpf_map's ID and bpf_prog's ID
are in two independent ID spaces and both have the same valid range:
[1, INT_MAX).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generates an unique ID for each BPF_PROG_LOAD-ed prog.
It is worth to note that each BPF_PROG_LOAD-ed prog will have
a different ID even they have the same bpf instructions.
The ID is generated by the existing idr_alloc_cyclic().
The ID is ranged from [1, INT_MAX). It is allocated in cyclic manner,
so an ID will get reused every 2 billion BPF_PROG_LOAD.
The bpf_prog_alloc_id() is done after bpf_prog_select_runtime()
because the jit process may have allocated a new prog. Hence,
we need to ensure the value of pointer 'prog' will not be changed
any more before storing the prog to the prog_idr.
After bpf_prog_select_runtime(), the prog is read-only. Hence,
the id is stored in 'struct bpf_prog_aux'.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow BPF_PROG_TYPE_PERF_EVENT program types to attach to all
perf_event types, including HW_CACHE, RAW, and dynamic pmu events.
Only tracepoint/kprobe events are treated differently which require
BPF_PROG_TYPE_TRACEPOINT/BPF_PROG_TYPE_KPROBE program types accordingly.
Also add support for reading all event counters using
bpf_perf_event_read() helper.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently loading a cgroup skb eBPF program require a CAP_SYS_ADMIN
capability while attaching the program to a cgroup only requires the
user have CAP_NET_ADMIN privilege. We can escape the capability
check when load the program just like socket filter program to make
the capability requirement consistent.
Change since v1:
Change the code style in order to be compliant with checkpatch.pl
preference
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows cgroup eBPF program to classify packet based on their
protocol or other detail information. Currently program need
CAP_NET_ADMIN privilege to attach a cgroup eBPF program, and A
process with CAP_NET_ADMIN can already see all packets on the system,
for example, by creating an iptables rules that causes the packet to
be passed to userspace via NFLOG.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
16 __bpf_prog_run() interpreters for various stack sizes add .text
but not a lot comparing to run-time stack savings
text data bss dec hex filename
26350 10328 624 37302 91b6 kernel/bpf/core.o.before_split
25777 10328 624 36729 8f79 kernel/bpf/core.o.after_split
26970 10328 624 37922 9422 kernel/bpf/core.o.now
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next set of patches will take advantage of stack_depth tracking,
so make sure that the program that does bpf_tail_call() has
stack depth large enough for the callee.
We could have tracked the stack depth of the prog_array owner program
and only allow insertion of the programs with stack depth less
than the owner, but it will break existing applications.
Some of them have trivial root bpf program that only does
multiple bpf_tail_calls and at init time the prog array is empty.
In the future we may add a flag to do such tracking optionally,
but for now play simple and safe.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
teach verifier to track bpf program stack depth
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
free up BPF_JMP | BPF_CALL | BPF_X opcode to be used by actual
indirect call by register and use kernel internal opcode to
mark call instruction into bpf_tail_call() helper.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix state pruning in bpf verifier wrt. alignment, from Daniel
Borkmann.
2) Handle non-linear SKBs properly in SCTP ICMP parsing, from Davide
Caratti.
3) Fix bit field definitions for rss_hash_type of descriptors in mlx5
driver, from Jesper Brouer.
4) Defer slave->link updates until bonding is ready to do a full commit
to the new settings, from Nithin Sujir.
5) Properly reference count ipv4 FIB metrics to avoid use after free
situations, from Eric Dumazet and several others including Cong Wang
and Julian Anastasov.
6) Fix races in llc_ui_bind(), from Lin Zhang.
7) Fix regression of ESP UDP encapsulation for TCP packets, from
Steffen Klassert.
8) Fix mdio-octeon driver Kconfig deps, from Randy Dunlap.
9) Fix regression in setting DSCP on ipv6/GRE encapsulation, from Peter
Dawson.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
bonding: Don't update slave->link until ready to commit
test_bpf: Add a couple of tests for BPF_JSGE.
bpf: add various verifier test cases
bpf: fix wrong exposure of map_flags into fdinfo for lpm
bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data
bpf: properly reset caller saved regs after helper call and ld_abs/ind
bpf: fix incorrect pruning decision when alignment must be tracked
arp: fixed -Wuninitialized compiler warning
tcp: avoid fastopen API to be used on AF_UNSPEC
net: move somaxconn init from sysctl code
net: fix potential null pointer dereference
geneve: fix fill_info when using collect_metadata
virtio-net: enable TSO/checksum offloads for Q-in-Q vlans
be2net: Fix offload features for Q-in-Q packets
vlan: Fix tcp checksum offloads in Q-in-Q vlans
...
trie_alloc() always needs to have BPF_F_NO_PREALLOC passed in via
attr->map_flags, since it does not support preallocation yet. We
check the flag, but we never copy the flag into trie->map.map_flags,
which is later on exposed into fdinfo and used by loaders such as
iproute2. Latter uses this in bpf_map_selfcheck_pinned() to test
whether a pinned map has the same spec as the one from the BPF obj
file and if not, bails out, which is currently the case for lpm
since it exposes always 0 as flags.
Also copy over flags in array_map_alloc() and stack_map_alloc().
They always have to be 0 right now, but we should make sure to not
miss to copy them over at a later point in time when we add actual
flags for them to use.
Fixes: b95a5c4db0 ("bpf: add a longest prefix match trie map implementation")
Reported-by: Jarno Rajahalme <jarno@covalent.io>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, after performing helper calls, we clear all caller saved
registers, that is r0 - r5 and fill r0 depending on struct bpf_func_proto
specification. The way we reset these regs can affect pruning decisions
in later paths, since we only reset register's imm to 0 and type to
NOT_INIT. However, we leave out clearing of other variables such as id,
min_value, max_value, etc, which can later on lead to pruning mismatches
due to stale data.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we enforce alignment tracking on direct packet access,
the verifier lets the following program pass despite doing a packet
write with unaligned access:
0: (61) r2 = *(u32 *)(r1 +76)
1: (61) r3 = *(u32 *)(r1 +80)
2: (61) r7 = *(u32 *)(r1 +8)
3: (bf) r0 = r2
4: (07) r0 += 14
5: (25) if r7 > 0x1 goto pc+4
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
6: (2d) if r0 > r3 goto pc+1
R0=pkt(id=0,off=14,r=14) R1=ctx R2=pkt(id=0,off=0,r=14)
R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
7: (63) *(u32 *)(r0 -4) = r0
8: (b7) r0 = 0
9: (95) exit
from 6 to 8:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
8: (b7) r0 = 0
9: (95) exit
from 5 to 10:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=2 R10=fp
10: (07) r0 += 1
11: (05) goto pc-6
6: safe <----- here, wrongly found safe
processed 15 insns
However, if we enforce a pruning mismatch by adding state into r8
which is then being mismatched in states_equal(), we find that for
the otherwise same program, the verifier detects a misaligned packet
access when actually walking that path:
0: (61) r2 = *(u32 *)(r1 +76)
1: (61) r3 = *(u32 *)(r1 +80)
2: (61) r7 = *(u32 *)(r1 +8)
3: (b7) r8 = 1
4: (bf) r0 = r2
5: (07) r0 += 14
6: (25) if r7 > 0x1 goto pc+4
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
7: (2d) if r0 > r3 goto pc+1
R0=pkt(id=0,off=14,r=14) R1=ctx R2=pkt(id=0,off=0,r=14)
R3=pkt_end R7=inv,min_value=0,max_value=1
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
8: (63) *(u32 *)(r0 -4) = r0
9: (b7) r0 = 0
10: (95) exit
from 7 to 9:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
9: (b7) r0 = 0
10: (95) exit
from 6 to 11:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=2
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
11: (07) r0 += 1
12: (b7) r8 = 0
13: (05) goto pc-7 <----- mismatch due to r8
7: (2d) if r0 > r3 goto pc+1
R0=pkt(id=0,off=15,r=15) R1=ctx R2=pkt(id=0,off=0,r=15)
R3=pkt_end R7=inv,min_value=2
R8=imm0,min_value=0,max_value=0,min_align=2147483648 R10=fp
8: (63) *(u32 *)(r0 -4) = r0
misaligned packet access off 2+15+-4 size 4
The reason why we fail to see it in states_equal() is that the
third test in compare_ptrs_to_packet() ...
if (old->off <= cur->off &&
old->off >= old->range && cur->off >= cur->range)
return true;
... will let the above pass. The situation we run into is that
old->off <= cur->off (14 <= 15), meaning that prior walked paths
went with smaller offset, which was later used in the packet
access after successful packet range check and found to be safe
already.
For example: Given is R0=pkt(id=0,off=0,r=0). Adding offset 14
as in above program to it, results in R0=pkt(id=0,off=14,r=0)
before the packet range test. Now, testing this against R3=pkt_end
with 'if r0 > r3 goto out' will transform R0 into R0=pkt(id=0,off=14,r=14)
for the case when we're within bounds. A write into the packet
at offset *(u32 *)(r0 -4), that is, 2 + 14 -4, is valid and
aligned (2 is for NET_IP_ALIGN). After processing this with
all fall-through paths, we later on check paths from branches.
When the above skb->mark test is true, then we jump near the
end of the program, perform r0 += 1, and jump back to the
'if r0 > r3 goto out' test we've visited earlier already. This
time, R0 is of type R0=pkt(id=0,off=15,r=0), and we'll prune
that part because this time we'll have a larger safe packet
range, and we already found that with off=14 all further insn
were already safe, so it's safe as well with a larger off.
However, the problem is that the subsequent write into the packet
with 2 + 15 -4 is then unaligned, and not caught by the alignment
tracking. Note that min_align, aux_off, and aux_off_align were
all 0 in this example.
Since we cannot tell at this time what kind of packet access was
performed in the prior walk and what minimal requirements it has
(we might do so in the future, but that requires more complexity),
fix it to disable this pruning case for strict alignment for now,
and let the verifier do check such paths instead. With that applied,
the test cases pass and reject the program due to misalignment.
Fixes: d117441674 ("bpf: Track alignment of register values in the verifier.")
Reference: http://patchwork.ozlabs.org/patch/761909/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ptrace fix from Eric Biederman:
"This fixes a brown paper bag bug. When I fixed the ptrace interaction
with user namespaces I added a new field ptracer_cred in struct_task
and I failed to properly initialize it on fork.
This dangling pointer wound up breaking runing setuid applications run
from the enlightenment window manager.
As this is the worst sort of bug. A regression breaking user space for
no good reason let's get this fixed"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ptrace: Properly initialize ptracer_cred on fork
When I introduced ptracer_cred I failed to consider the weirdness of
fork where the task_struct copies the old value by default. This
winds up leaving ptracer_cred set even when a process forks and
the child process does not wind up being ptraced.
Because ptracer_cred is not set on non-ptraced processes whose
parents were ptraced this has broken the ability of the enlightenment
window manager to start setuid children.
Fix this by properly initializing ptracer_cred in ptrace_init_task
This must be done with a little bit of care to preserve the current value
of ptracer_cred when ptrace carries through fork. Re-reading the
ptracer_cred from the ptracing process at this point is inconsistent
with how PT_PTRACE_CAP has been maintained all of these years.
Tested-by: Takashi Iwai <tiwai@suse.de>
Fixes: 64b875f7ac ("ptrace: Capture the ptracer's creds not PT_PTRACE_CAP")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
- Fix RTC wakeup from suspend-to-idle broken by the recent rework
of ACPI wakeup handling (Rafael Wysocki).
- Update intel_pstate driver documentation to reflect the current
code and explain how it works in more detail (Rafael Wysocki).
- Fix an issue related to CPU idleness detection on systems with
shared cpufreq policies in the schedutil governor (Juri Lelli).
- Fix a possible build issue in the dbx500 cpufreq driver (Arnd
Bergmann).
- Fix a function in the power capping framework core to return
an error code instead of 0 when there's an error (Dan Carpenter).
- Clean up variable definition in the hibernation core (Pushkar
Jambhlekar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=2sNW
-----END PGP SIGNATURE-----
Merge tag 'pm-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix RTC wakeup from suspend-to-idle broken recently, fix CPU
idleness detection condition in the schedutil cpufreq governor, fix a
cpufreq driver build failure, fix an error code path in the power
capping framework, clean up the hibernate core and update the
intel_pstate documentation.
Specifics:
- Fix RTC wakeup from suspend-to-idle broken by the recent rework of
ACPI wakeup handling (Rafael Wysocki).
- Update intel_pstate driver documentation to reflect the current
code and explain how it works in more detail (Rafael Wysocki).
- Fix an issue related to CPU idleness detection on systems with
shared cpufreq policies in the schedutil governor (Juri Lelli).
- Fix a possible build issue in the dbx500 cpufreq driver (Arnd
Bergmann).
- Fix a function in the power capping framework core to return an
error code instead of 0 when there's an error (Dan Carpenter).
- Clean up variable definition in the hibernation core (Pushkar
Jambhlekar)"
* tag 'pm-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: dbx500: add a Kconfig symbol
PM / hibernate: Declare variables as static
PowerCap: Fix an error code in powercap_register_zone()
RTC: rtc-cmos: Fix wakeup from suspend-to-idle
PM / wakeup: Fix up wakeup_source_report_event()
cpufreq: intel_pstate: Document the current behavior and user interface
cpufreq: schedutil: use now as reference when aggregating shared policy requests
Pull networking fixes from David Miller:
"Mostly netfilter bug fixes in here, but we have some bits elsewhere as
well.
1) Don't do SNAT replies for non-NATed connections in IPVS, from
Julian Anastasov.
2) Don't delete conntrack helpers while they are still in use, from
Liping Zhang.
3) Fix zero padding in xtables's xt_data_to_user(), from Willem de
Bruijn.
4) Add proper RCU protection to nf_tables_dump_set() because we
cannot guarantee that we hold the NFNL_SUBSYS_NFTABLES lock. From
Liping Zhang.
5) Initialize rcv_mss in tcp_disconnect(), from Wei Wang.
6) smsc95xx devices can't handle IPV6 checksums fully, so don't
advertise support for offloading them. From Nisar Sayed.
7) Fix out-of-bounds access in __ip6_append_data(), from Eric
Dumazet.
8) Make atl2_probe() propagate the error code properly on failures,
from Alexey Khoroshilov.
9) arp_target[] in bond_check_params() is used uninitialized. This
got changes from a global static to a local variable, which is how
this mistake happened. Fix from Jarod Wilson.
10) Fix fallout from unnecessary NULL check removal in cls_matchall,
from Jiri Pirko. This is definitely brown paper bag territory..."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
net: sched: cls_matchall: fix null pointer dereference
vsock: use new wait API for vsock_stream_sendmsg()
bonding: fix randomly populated arp target array
net: Make IP alignment calulations clearer.
bonding: fix accounting of active ports in 3ad
net: atheros: atl2: don't return zero on failure path in atl2_probe()
ipv6: fix out of bound writes in __ip6_append_data()
bridge: start hello_timer when enabling KERNEL_STP in br_stp_start
smsc95xx: Support only IPv4 TCP/UDP csum offload
arp: always override existing neigh entries with gratuitous ARP
arp: postpone addr_type calculation to as late as possible
arp: decompose is_garp logic into a separate function
arp: fixed error in a comment
tcp: initialize rcv_mss to TCP_MIN_MSS instead of 0
netfilter: xtables: fix build failure from COMPAT_XT_ALIGN outside CONFIG_COMPAT
ebtables: arpreply: Add the standard target sanity check
netfilter: nf_tables: revisit chain/object refcounting from elements
netfilter: nf_tables: missing sanitization in data from userspace
netfilter: nf_tables: can't assume lock is acquired when dumping set elems
netfilter: synproxy: fix conntrackd interaction
...
* intel_pstate:
cpufreq: intel_pstate: Document the current behavior and user interface
* pm-cpufreq:
cpufreq: dbx500: add a Kconfig symbol
* pm-cpufreq-sched:
cpufreq: schedutil: use now as reference when aggregating shared policy requests
The assignmnet:
ip_align = strict ? 2 : NET_IP_ALIGN;
in compare_pkt_ptr_alignment() trips up Coverity because we can only
get to this code when strict is true, therefore ip_align will always
be 2 regardless of NET_IP_ALIGN's value.
So just assign directly to '2' and explain the situation in the
comment above.
Reported-by: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler fix from Thomas Gleixner:
"A single scheduler fix:
Prevent idle task from ever being preempted. That makes sure that
synchronize_rcu_tasks() which is ignoring idle task does not pretend
that no task is stuck in preempted state. If that happens and idle was
preempted on a ftrace trampoline the machine crashes due to
inconsistent state"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Call __schedule() from do_idle() without enabling preemption
Pull irq fixes from Thomas Gleixner:
"A set of small fixes for the irq subsystem:
- Cure a data ordering problem with chained interrupts
- Three small fixlets for the mbigen irq chip"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix chained interrupt data ordering
irqchip/mbigen: Fix the clear register offset calculation
irqchip/mbigen: Fix potential NULL dereferencing
irqchip/mbigen: Fix memory mapping code
when deleting an instance. It also creates a selftest that triggers that bug.
Fix the delayed optimization happening after kprobes boot up self tests
being removed by freeing of init memory.
Comment kprobes on why the delay optimization is not a problem for removal
of modules, to keep other developers from searching that riddle.
Fix another rcu isn't watching in stack trace tracing.
Naveen N. Rao (4):
ftrace: Simplify glob handling in unregister_ftrace_function_probe_func()
ftrace/instances: Clear function triggers when removing instances
selftests/ftrace: Fix bashisms
selftests/ftrace: Add test to remove instance with active event triggers
Steven Rostedt (1):
tracing: Move postpone selftests to core from early_initcall
Steven Rostedt (VMware) (3):
ftrace: Remove #ifdef from code and add clear_ftrace_function_probes() stub
kprobes: Document how optimized kprobes are removed from module unload
tracing: Make sure RCU is watching before calling a stack trace
Thomas Gleixner (1):
tracing/kprobes: Enforce kprobes teardown after testing
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJZIQapFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
A6MIAKFLb6mQ4flRBXpWd2tD2B4DQpQ0H7SovseZnlH6Q7grU6POY/qbNl9xXiBA
3NavxqbIYokH8cxEqGAusL7ASUFPXJj6erMM1uc1WRuAzMpIjvgNacOtW5R+c5S9
ofR1xtKlBo/854J/IP6M3J0WqrK+B7TsS1WYKohe/tFMBpolbnFloHVfMMZlaL58
CQhCoAhkjJRsta6dJhbo+HoQy03VGyWsfFHtutBpIwsf81Naq4Stpxp7jdZLWhB8
Di5QdOji9lDayK6Uk7DDZqHxbjC9z6cCS9nVWIGHkE4AMpR3peYtsyCaAOBjVMLV
2OuhuREfZgKaYVMjUfdeYCayDAY=
=1gek
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix a bug caused by not cleaning up the new instance unique triggers
when deleting an instance. It also creates a selftest that triggers
that bug.
- Fix the delayed optimization happening after kprobes boot up self
tests being removed by freeing of init memory.
- Comment kprobes on why the delay optimization is not a problem for
removal of modules, to keep other developers from searching that
riddle.
- Fix another case of rcu not watching in stack trace tracing.
* tag 'trace-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Make sure RCU is watching before calling a stack trace
kprobes: Document how optimized kprobes are removed from module unload
selftests/ftrace: Add test to remove instance with active event triggers
selftests/ftrace: Fix bashisms
ftrace: Remove #ifdef from code and add clear_ftrace_function_probes() stub
ftrace/instances: Clear function triggers when removing instances
ftrace: Simplify glob handling in unregister_ftrace_function_probe_func()
tracing/kprobes: Enforce kprobes teardown after testing
tracing: Move postpone selftests to core from early_initcall
Pull block fixes from Jens Axboe:
"A small collection of fixes that should go into this cycle.
- a pull request from Christoph for NVMe, which ended up being
manually applied to avoid pulling in newer bits in master. Mostly
fibre channel fixes from James, but also a few fixes from Jon and
Vijay
- a pull request from Konrad, with just a single fix for xen-blkback
from Gustavo.
- a fuseblk bdi fix from Jan, fixing a regression in this series with
the dynamic backing devices.
- a blktrace fix from Shaohua, replacing sscanf() with kstrtoull().
- a request leak fix for drbd from Lars, fixing a regression in the
last series with the kref changes. This will go to stable as well"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: release the sq ref on rdma read errors
nvmet-fc: remove target cpu scheduling flag
nvme-fc: stop queues on error detection
nvme-fc: require target or discovery role for fc-nvme targets
nvme-fc: correct port role bits
nvme: unmap CMB and remove sysfs file in reset path
blktrace: fix integer parse
fuseblk: Fix warning in super_setup_bdi_name()
block: xen-blkback: add null check to avoid null pointer dereference
drbd: fix request leak introduced by locking/atomic, kref: Kill kref_sub()
sscanf is a very poor way to parse integer. For example, I input
"discard" for act_mask, it gets 0xd and completely messes up. Using
correct API to do integer parse.
This patch also makes attributes accept any base of integer.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As stack tracing now requires "rcu watching", force RCU to be watching when
recording a stack trace.
Link: http://lkml.kernel.org/r/20170512172449.879684501@goodmis.org
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull networking fixes from David Miller:
1) Don't allow negative TCP reordering values, from Soheil Hassas
Yeganeh.
2) Don't overflow while parsing ipv6 header options, from Craig Gallek.
3) Handle more cleanly the case where an individual route entry during
a dump will not fit into the allocated netlink SKB, from David
Ahern.
4) Add missing CONFIG_INET dependency for mlx5e, from Arnd Bergmann.
5) Allow neighbour updates to converge more quickly via gratuitous
ARPs, from Ihar Hrachyshka.
6) Fix compile error from CONFIG_INET is disabled, from Eric Dumazet.
7) Fix use after free in x25 protocol init, from Lin Zhang.
8) Valid VLAN pvid ranges passed into br_validate(), from Tobias
Jungel.
9) NULL out address lists in child sockets in SCTP, this is similar to
the fix we made for inet connection sockets last week. From Eric
Dumazet.
10) Fix NULL deref in mlxsw driver, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
mlxsw: spectrum: Avoid possible NULL pointer dereference
sh_eth: Do not print an error message for probe deferral
sh_eth: Use platform device for printing before register_netdev()
mlxsw: spectrum_router: Fix rif counter freeing routine
mlxsw: spectrum_dpipe: Fix incorrect entry index
cxgb4: update latest firmware version supported
qmi_wwan: add another Lenovo EM74xx device ID
sctp: do not inherit ipv6_{mc|ac|fl}_list from parent
udp: make *udp*_queue_rcv_skb() functions static
bridge: netlink: check vlan_default_pvid range
net: ethernet: faraday: To support device tree usage.
net: x25: fix one potential use-after-free issue
bpf: adjust verifier heuristics
ipv6: Check ip6_find_1stfragopt() return value properly.
selftests/bpf: fix broken build due to types.h
bnxt_en: Check status of firmware DCBX agent before setting DCB_CAP_DCBX_HOST.
bnxt_en: Call bnxt_dcb_init() after getting firmware DCBX configuration.
net: fix compile error in skb_orphan_partial()
ipv6: Prevent overrun when parsing v6 header options
neighbour: update neigh timestamps iff update is effective
...
Pull pid namespace fixes from Eric Biederman:
"These are two bugs that turn out to have simple fixes that were
reported during the merge window. Both of these issues have existed
for a while and it just happens that they both were reported at almost
the same time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
pid_ns: Fix race between setns'ed fork() and zap_pid_ns_processes()
pid_ns: Sleep in TASK_INTERRUPTIBLE in zap_pid_ns_processes
Current limits with regards to processing program paths do not
really reflect today's needs anymore due to programs becoming
more complex and verifier smarter, keeping track of more data
such as const ALU operations, alignment tracking, spilling of
PTR_TO_MAP_VALUE_ADJ registers, and other features allowing for
smarter matching of what LLVM generates.
This also comes with the side-effect that we result in fewer
opportunities to prune search states and thus often need to do
more work to prove safety than in the past due to different
register states and stack layout where we mismatch. Generally,
it's quite hard to determine what caused a sudden increase in
complexity, it could be caused by something as trivial as a
single branch somewhere at the beginning of the program where
LLVM assigned a stack slot that is marked differently throughout
other branches and thus causing a mismatch, where verifier
then needs to prove safety for the whole rest of the program.
Subsequently, programs with even less than half the insn size
limit can get rejected. We noticed that while some programs
load fine under pre 4.11, they get rejected due to hitting
limits on more recent kernels. We saw that in the vast majority
of cases (90+%) pruning failed due to register mismatches. In
case of stack mismatches, majority of cases failed due to
different stack slot types (invalid, spill, misc) rather than
differences in spilled registers.
This patch makes pruning more aggressive by also adding markers
that sit at conditional jumps as well. Currently, we only mark
jump targets for pruning. For example in direct packet access,
these are usually error paths where we bail out. We found that
adding these markers, it can reduce number of processed insns
by up to 30%. Another option is to ignore reg->id in probing
PTR_TO_MAP_VALUE_OR_NULL registers, which can help pruning
slightly as well by up to 7% observed complexity reduction as
stand-alone. Meaning, if a previous path with register type
PTR_TO_MAP_VALUE_OR_NULL for map X was found to be safe, then
in the current state a PTR_TO_MAP_VALUE_OR_NULL register for
the same map X must be safe as well. Last but not least the
patch also adds a scheduling point and bumps the current limit
for instructions to be processed to a more adequate value.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas discovered a bug where the kprobe trace tests had a race
condition where the kprobe_optimizer called from a delayed work queue
that does the optimizing and "unoptimizing" of a kprobe, can try to
modify the text after it has been freed by the init code.
The kprobe trace selftest is a special case, and Thomas and myself
investigated to see if there's a chance that this could also be a bug
with module unloading, as the code is not obvious to how it handles
this. After adding lots of printks, I figured it out. Thomas suggested
that this should be commented so that others will not have to go
through this exercise again.
Link: http://lkml.kernel.org/r/20170516145835.3827d3aa@gandalf.local.home
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Enabling the tracer selftest triggers occasionally the warning in
text_poke(), which warns when the to be modified page is not marked
reserved.
The reason is that the tracer selftest installs kprobes on functions marked
__init for testing. These probes are removed after the tests, but that
removal schedules the delayed kprobes_optimizer work, which will do the
actual text poke. If the work is executed after the init text is freed,
then the warning triggers. The bug can be reproduced reliably when the work
delay is increased.
Flush the optimizer work and wait for the optimizing/unoptimizing lists to
become empty before returning from the kprobes tracer selftest. That
ensures that all operations which were queued due to the probes removal
have completed.
Link: http://lkml.kernel.org/r/20170516094802.76a468bb@gandalf.local.home
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 6274de498 ("kprobes: Support delayed unoptimizing")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
irq_set_chained_handler_and_data() sets up the chained interrupt and then
stores the handler data.
That's racy against an immediate interrupt which gets handled before the
store of the handler data happened. The handler will dereference a NULL
pointer and crash.
Cure it by storing handler data before installing the chained handler.
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Pull networking fixes from David Miller:
1) Track alignment in BPF verifier so that legitimate programs won't be
rejected on !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS architectures.
2) Make tail calls work properly in arm64 BPF JIT, from Deniel
Borkmann.
3) Make the configuration and semantics Generic XDP make more sense and
don't allow both generic XDP and a driver specific instance to be
active at the same time. Also from Daniel.
4) Don't crash on resume in xen-netfront, from Vitaly Kuznetsov.
5) Fix use-after-free in VRF driver, from Gao Feng.
6) Use netdev_alloc_skb_ip_align() to avoid unaligned IP headers in
qca_spi driver, from Stefan Wahren.
7) Always run cleanup routines in BPF samples when we get SIGTERM, from
Andy Gospodarek.
8) The mdio phy code should bring PHYs out of reset using the shared
GPIO lines before invoking bus->reset(). From Florian Fainelli.
9) Some USB descriptor access endian fixes in various drivers from
Johan Hovold.
10) Handle PAUSE advertisements properly in mlx5 driver, from Gal
Pressman.
11) Fix reversed test in mlx5e_setup_tc(), from Saeed Mahameed.
12) Cure netdev leak in AF_PACKET when using timestamping via control
messages. From Douglas Caetano dos Santos.
13) netcp doesn't support HWTSTAMP_FILTER_ALl, reject it. From Miroslav
Lichvar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
ldmvsw: stop the clean timer at beginning of remove
ldmvsw: unregistering netdev before disable hardware
net: netcp: fix check of requested timestamping filter
ipv6: avoid dad-failures for addresses with NODAD
qed: Fix uninitialized data in aRFS infrastructure
mdio: mux: fix device_node_continue.cocci warnings
net/packet: fix missing net_device reference release
net/mlx4_core: Use min3 to select number of MSI-X vectors
macvlan: Fix performance issues with vlan tagged packets
net: stmmac: use correct pointer when printing normal descriptor ring
net/mlx5: Use underlay QPN from the root name space
net/mlx5e: IPoIB, Only support regular RQ for now
net/mlx5e: Fix setup TC ndo
net/mlx5e: Fix ethtool pause support and advertise reporting
net/mlx5e: Use the correct pause values for ethtool advertising
vmxnet3: ensure that adapter is in proper state during force_close
sfc: revert changes to NIC revision numbers
net: ch9200: add missing USB-descriptor endianness conversions
net: irda: irda-usb: fix firmware name on big-endian hosts
net: dsa: mv88e6xxx: add default case to switch
...
I finally got around to creating trampolines for dynamically allocated
ftrace_ops with using synchronize_rcu_tasks(). For users of the ftrace
function hook callbacks, like perf, that allocate the ftrace_ops
descriptor via kmalloc() and friends, ftrace was not able to optimize
the functions being traced to use a trampoline because they would also
need to be allocated dynamically. The problem is that they cannot be
freed when CONFIG_PREEMPT is set, as there's no way to tell if a task
was preempted on the trampoline. That was before Paul McKenney
implemented synchronize_rcu_tasks() that would make sure all tasks
(except idle) have scheduled out or have entered user space.
While testing this, I triggered this bug:
BUG: unable to handle kernel paging request at ffffffffa0230077
...
RIP: 0010:0xffffffffa0230077
...
Call Trace:
schedule+0x5/0xe0
schedule_preempt_disabled+0x18/0x30
do_idle+0x172/0x220
What happened was that the idle task was preempted on the trampoline.
As synchronize_rcu_tasks() ignores the idle thread, there's nothing
that lets ftrace know that the idle task was preempted on a trampoline.
The idle task shouldn't need to ever enable preemption. The idle task
is simply a loop that calls schedule or places the cpu into idle mode.
In fact, having preemption enabled is inefficient, because it can
happen when idle is just about to call schedule anyway, which would
cause schedule to be called twice. Once for when the interrupt came in
and was returning back to normal context, and then again in the normal
path that the idle loop is running in, which would be pointless, as it
had already scheduled.
The only reason schedule_preempt_disable() enables preemption is to be
able to call sched_submit_work(), which requires preemption enabled. As
this is a nop when the task is in the RUNNING state, and idle is always
in the running state, there's no reason that idle needs to enable
preemption. But that means it cannot use schedule_preempt_disable() as
other callers of that function require calling sched_submit_work().
Adding a new function local to kernel/sched/ that allows idle to call
the scheduler without enabling preemption, fixes the
synchronize_rcu_tasks() issue, as well as removes the pointless spurious
schedule calls caused by interrupts happening in the brief window where
preemption is enabled just before it calls schedule.
Reviewed: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170414084809.3dacde2a@gandalf.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fixing sparse warnings: 'symbol not declared. Should it be static?'
Signed-off-by: Pushkar Jambhlekar <pushkar.iit@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Imagine we have a pid namespace and a task from its parent's pid_ns,
which made setns() to the pid namespace. The task is doing fork(),
while the pid namespace's child reaper is dying. We have the race
between them:
Task from parent pid_ns Child reaper
copy_process() ..
alloc_pid() ..
.. zap_pid_ns_processes()
.. disable_pid_allocation()
.. read_lock(&tasklist_lock)
.. iterate over pids in pid_ns
.. kill tasks linked to pids
.. read_unlock(&tasklist_lock)
write_lock_irq(&tasklist_lock); ..
attach_pid(p, PIDTYPE_PID); ..
.. ..
So, just created task p won't receive SIGKILL signal,
and the pid namespace will be in contradictory state.
Only manual kill will help there, but does the userspace
care about this? I suppose, the most users just inject
a task into a pid namespace and wait a SIGCHLD from it.
The patch fixes the problem. It simply checks for
(pid_ns->nr_hashed & PIDNS_HASH_ADDING) in copy_process().
We do it under the tasklist_lock, and can't skip
PIDNS_HASH_ADDING as noted by Oleg:
"zap_pid_ns_processes() does disable_pid_allocation()
and then takes tasklist_lock to kill the whole namespace.
Given that copy_process() checks PIDNS_HASH_ADDING
under write_lock(tasklist) they can't race;
if copy_process() takes this lock first, the new child will
be killed, otherwise copy_process() can't miss
the change in ->nr_hashed."
If allocation is disabled, we just return -ENOMEM
like it's made for such cases in alloc_pid().
v2: Do not move disable_pid_allocation(), do not
introduce a new variable in copy_process() and simplify
the patch as suggested by Oleg Nesterov.
Account the problem with double irq enabling
found by Eric W. Biederman.
Fixes: c876ad7682 ("pidns: Stop pid allocation when init dies")
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Ingo Molnar <mingo@kernel.org>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Mike Rapoport <rppt@linux.vnet.ibm.com>
CC: Michal Hocko <mhocko@suse.com>
CC: Andy Lutomirski <luto@kernel.org>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Andrei Vagin <avagin@openvz.org>
CC: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Serge Hallyn <serge@hallyn.com>
Cc: stable@vger.kernel.org
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The code can potentially sleep for an indefinite amount of time in
zap_pid_ns_processes triggering the hung task timeout, and increasing
the system average. This is undesirable. Sleep with a task state of
TASK_INTERRUPTIBLE instead of TASK_UNINTERRUPTIBLE to remove these
undesirable side effects.
Apparently under heavy load this has been allowing Chrome to trigger
the hung time task timeout error and cause ChromeOS to reboot.
Reported-by: Vovo Yang <vovoy@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 6347e90091 ("pidns: guarantee that the pidns init will be the last pidns process reaped")
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
All uses of the current_fs_time() function have been replaced by other
time interfaces.
And, its use cases can be fulfilled by current_time() or ktime_get_*
variants.
Link: http://lkml.kernel.org/r/1491613030-11599-13-git-send-email-deepa.kernel@gmail.com
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf updates/fixes from Ingo Molnar:
"Mostly tooling updates, but also two kernel fixes: a call chain
handling robustness fix and an x86 PMU driver event definition fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/callchain: Force USER_DS when invoking perf_callchain_user()
tools build: Fixup sched_getcpu feature test
perf tests kmod-path: Don't fail if compressed modules aren't supported
perf annotate: Fix AArch64 comment char
perf tools: Fix spelling mistakes
perf/x86: Fix Broadwell-EP DRAM RAPL events
perf config: Refactor a duplicated code for obtaining config file name
perf symbols: Allow user probes on versioned symbols
perf symbols: Accept symbols starting at address 0
tools lib string: Adopt prefixcmp() from perf and subcmd
perf units: Move parse_tag_value() to units.[ch]
perf ui gtk: Move gtk .so name to the only place where it is used
perf tools: Move HAS_BOOL define to where perl headers are used
perf memswap: Split the byteswap memory range wrappers from util.[ch]
perf tools: Move event prototypes from util.h to event.h
perf buildid: Move prototypes from util.h to build-id.h
