This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This requires adding a pointer to
hold the timer's target task, as there isn't a link back from slow_task.
Cc: John Garry <john.garry@huawei.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jack Wang <jinpu.wang@profitbricks.com>
Cc: lindar_liu@usish.com
Cc: Jens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: John Garry <john.garry@huawei.com> # for hisi_sas part
Tested-by: John Garry <john.garry@huawei.com> # basic sanity test for hisi_sas
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
The CQ event is handled in tasklet context, and it could be delayed if
the system loading is high.
It is possible to run into some problems when executing a host reset
when cq_tasklet_vx_hw() is being executed.
So, prior to host reset, execute tasklet_kill() to ensure that all CQ
tasklets are complete.
Besides, as the function hisi_sas_wait_tasklets_done() is added to do
tasklet_kill(), this patch refactors some code where tasklet_kill() is
used.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code to print AXI errors in v2 hw driver is repetitive.
This patch condenses the code by looping an array of errors.
Also, a formatting error in one_bit_ecc_errors[] and
multi_bit_ecc_errors[] is fixed.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a PHY_FUNC_LINK_RESET is issued, we need to fill the transport
identify_frame to SAS controller before the PHYs are enabled.
Without this, we may find that if a PHY which belonged to a wideport
before the reset may generate a new port id.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When adding/removing slots from device list, we need to lock this
operation with hisi_hba lock for safety.
This patch adds missing instances of this.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We used spin_lock() to grab hisi_hba.lock in two places where
spin_lock_irqsave() should be used, as hisi_hba.lock can be taken in
interrupt context.
This patch is to fix this.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use ACPI "_RST" method to reset the controller, since FLR is not
supported.
Function hisi_sas_stop_phys() is introduced to remove some code
duplication.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is a fix related to freeing a device in v2 hw driver.
Before, we polled to ITCT CLR interrupt to check if a device is free.
This was error prone, as if the interrupt doesn't occur in 10us, we miss
processing it.
To avoid this situation, service this interrupt and sync the event with
a completion.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to clean-up allocated IRQs and kill tasklets
when probe fails and for driver removal.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code to print ECC errors in v2 hw driver is very repetitive. This
patch condensed the code by looping an array of errors.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add DFX feature for v2 hw. We are adding support for
the following errors:
- loss_of_dword_sync_count
- invalid_dword_count
- phy_reset_problem_count
- running_disparity_error_count
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value dw0 is the residual bytes when UNDERFLOW error happens, but we
filled the residual with the value of dw3 before. So change the residual
from dw3 to dw0.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When some interrupts happen together, we need to process every interrupt
one-by-one, and should not return immediately when one interrupt process
is finished being processed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides fixes for the following issues:
1. Fix issue of controller reset required to send commands. For reset
process, it may be required to send commands to the controller, but
not during soft reset. So add HISI_SAS_NOT_ACCEPT_CMD_BIT to prevent
executing a task during this period.
2. Send a broadcast event in rescan topology to detect any topology
changes during reset.
3. Previously it was not ensured that libsas has processed the PHY up
and down events after reset. Potentially this could cause an issue
that we still process the PHY event after reset. So resolve this by
flushing shot workqueue in LLDD reset.
4. Port ID requires refresh after reset. The port ID generated after
reset is not guaranteed to be the same as before reset, so it needs
to be refreshed for each device's ITCT.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't populate various tables on the stack but make them static const.
Makes the object code smaller by over 280 bytes:
Before:
text data bss dec hex filename
39887 5080 64 45031 afe7 hisi_sas_v2_hw.o
After:
text data bss dec hex filename
39318 5368 64 44750 aece hisi_sas_v2_hw.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we allocate 3 sets of DMA memories from separate pools for
each slot. This is inefficient in terms of memory usage
(buffers are less than 1 page in size, so we lose due to alignment),
and also time spent in doing 3 allocations + de-allocations per slot,
instead of 1.
To optimise, combine the 3 DMA buffers into a single buffer from a
single pool.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since hip08 SAS controller is based on pci device, add hisi_hba.pci_dev
for hip08 (will be v3), and also rename hisi_hba.pdev to .platform_dev
for clarity.
In addition, for common code which wants to reference the controller
device struct, add hisi_hba.dev, and change the common code to use it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate get_ncq_tag_v2_hw() to a common location, as future hw versions
will require it. Also rename with "hisi_sas_" prefix for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate get_ata_protocol() to a common location, as future hw versions
will require it. Also rename with "hisi_sas_" prefix for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate get_ata_protocol() to a common location, as future hw versions
will require it. Also rename with "hisi_sas_" prefix for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently hisi_hba.lock is locked to deliver and receive a command
to/from any hw queue. This causes much contention at high data-rates.
To boost performance, lock on a per queue basis for sending and
receiving commands to/from hw.
Certain critical regions still need to be locked in the delivery and
completion stages with hisi_hba.lock.
New element hisi_sas_device.dq is added to store the delivery queue for
a device, so it does not need to be needlessly re-calculated for every
task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For 1 bit ECC errors, those errors can be recovered by hw. But for
multi-bits ECC and AXI errors, there are something wrong with whole
module or system, so try reset the controller to recover those errors
instead of calling panic().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is a workaround for a SoC bug where an internal abort command
may timeout. In v2 hw, the channel should become idle in order to finish
abort process. If the target side has been sending HOLD, host side
channel failed to complete the frame to send, and can not enter the idle
state. Then internal abort command will timeout.
As this issue is only in v2 hw, we deal with it in the hw layer. Our
workaround solution is: If abort is not finished within a certain period
of time, we will check HOLD status. If HOLD has been sending, we will
send break command.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a workaround solution for a SoC bug which may cause SoC
logic fatal error when disabling a PHY. Then we find internal abort IO
timeout may occur, and the controller IO breakpoint may be corrupted.
We work around this SoC bug by optimizing the flow of disabling a PHY.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides a workaround a SoC bug where SATA IPTTs for
different devices may conflict.
The workaround solution requests the following:
1. SATA device id must be even and not equal to SAS IPTT.
2. SATA device can not share the same IPTT with other SAS or
SATA device.
Besides we shall consider IPTT value 0 is reserved for another SoC bug
(STP device open link at firstly after SAS controller reset).
To sum up, the solution is: Each SATA device uses independent and
continuous 32 even IPTT from 64 to 4094, then v2 hw can only support 63
SATA devices. All SAS device(SSP/SMP devices) share odd IPTT value from
1 to 4095.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After resetting the controller, the process of scanning SATA disks
attached to an expander may fail occasionally. The issue is that the
controller can't close the STP link created by target if the max link
time is 0.
To workaround this issue, we reject STP link after resetting the
controller, and change the corresponding PHY to accept STP link only
after receiving data.
We do this check in cq interrupt handler. In order not to reduce
efficiency, we use an variable to control whether we should check and
change PHY to accept STP link.
The function phys_reject_stp_links_v2_hw() should be called after
resetting the controller.
The solution of another SoC bug "SATA IO timeout", that also uses the
same register to control STP link, is not effective before the PHY
accepts STP link.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It appears that a break in the TRANS_TX_OPEN_CNX_ERR_NO_DESTINATION case
got accidentally removed in an earlier commit, as it stands, the
ts->stat and ts->open_rej_reason are being updated twice for this case
which looks incorrect. Fix this by adding in the missing break
statement.
Detected by CoverityScan, CID#1422110 ("Missing break in switch")
Fixes: 634a9585f4 ("scsi: hisi_sas: process error codes according to their priority")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add helper function is_sata_phy_v2_hw() to judge whether the attached
device is SATA disk for a root PHY.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For consistency, remove the "hisi_sas_" prefix.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Handle the situation that PHY UP and DOWN irq happen simultaneously.
There is no mechanism of SoC HW to ensure this situation will never
happen. So, we add this handle just in case.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch includes:
(1) Disable transport layer retry
(2) Support CQ time and count interrupt coal
(3) fix link FIFO full issue
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Zhao Nenglong <zhaonenglong@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are some rules to decide which error code has the high priority
when errors happen together:
(1) Error phase of CQ decides the error happens on RX or TX;
(2) For TX error, when DMA/TRANS TX error happen simultaneously, the
priority of DMA TX error is higher than TRANS TX error, so for the
priority of TX error: DW2 (DMA TX part) > DW0;
(3) For RX error, when TRANS/DMA/SIPC RX error happen simultaneously,
the priority of TRANS RX error is higher than DMA and SIPC RX error,
and we should also keep the rules (the priority of DW3 > DW2), so
for the priority of RX error: DW1 > DW3 > DW2(SIPC RX part);
(4) There are also a priority we should keep in the same error type.
So, modify slot error code to handle this.
In addition to this, some some error codes are modified according to
recommendation from SoC designer.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some more locking needs to be added/modified for when
read-modify-writing sas_task.task_state_flags.
Note: since we can attempt to grab this lock in interrupt
context we should use irq variant of spin_lock.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check in slot_complete_v2_hw() for whether a task has already been
completed by upper layer.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently an internal abort is executed regardless of the result of the
TMF. We should also check the result of the internal abort to see if we
should free the slot.
So change the status code STAT_IO_COMPLETE to TMF_RESP_FUNC_SUCC,
meaning the slot has been successfully aborted.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For error codes which need abort-and-retry, simulate IO timeout and let
SCSI+ATA layers process those errors.
Previously for SSP, we should try to abort the IO in the LLDD and then
pass back to upper layer, but sometimes this would also error. So
Instead of adding special error handling for this scenario in the LLDD,
allow the upper layer to handle completely.
No performance hit is seen by taking this approach.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently when a root PHY is deformed from a asd_sas_port we try to
release the slots in the LLDD, and fail.
Regardless, it is not right to release this early.
This patch removes the deformed function. As it was before, port
deformation is still done in hisi_sas_phy_down().
It would be nice to actually remove the hisi_sas_port_{de}formed() pair,
however we cannot as we need to know the asd_sas_port index libsas has
associated with an asd_sas_phy.
The hw does actually generate a port id for a PHY, but this seems to a
random number, so ignored for this purpose.
This patch also changes the code to link slots to the hisi_sas_device,
and not hisi_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add softreset to clear IO after internal abort device for SATA disk.
The SATA error handling for the controller is based on device internal
abort and softreset function.
The controller does not support internal abort for single IO, so we need
to execute internal abort for device.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate the PHY init code from LLDD hw init path to
hisi_sas_scan_start().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are some scenarios that we need to warm-reset to reset registers
of SAS controller. During reset we disable interrupts/DQs/PHYs, and
after reset we re-init the hardware and rescan the topology to see if
anything changed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce function to get hisi_sas_port from asd_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is an issue that hisi_sas_dev.running_req is not
decremented properly for internal abort and TMF.
To resolve, only decrease running_req in hisi_sas_slot_task_free()
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a potential probe issue in how we trigger the hw initialisation.
Although we use 1s timer to delay hw initialisation, there is still a
potential that sas_register_ha() is not be finished before we start
the PHY init from hw->hw_init().
To avoid this issue, initialise the hw after sas_register_ha() in the
same probe context.
Note: it is not necessary to use 1s timer now (modified v2 hw only).
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correctly set registers in v2 for root PHY hardreset for directly
attached disk.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set SMP connection timeout and continue AWT timer;
Clear ITCT table when dev gone.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The v2 SAS controller needs more time to detect channel idle
and send setup link request than SATA disk does, so it is
difficult for the SAS controller to setup an STP link. Therefore
it may cause some IO timeouts.
We need to periodically configure the SAS controller so it
doesn't receive STP setup requests from SATA disks for a while,
so IO can be sent during this period.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a bug in the current driver in that certain hisi_hba and port
structure elements which we access when servicing the CQ interrupt do
not use thread-safe accesses; these include hisi_sas_port linked-list of
active slots (hisi_sas_port.entry), bitmap of currently allocated IPTT
(in hisi_hba.slot_index_tags), and completion queue read pointer.
As a solution, lock these elements with the hisi_hba.lock.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the all the slot processing for the completion queue is done
in ISR context. It is judged that the slot processing can take a long
time, especially when a SATA NCQ completes (upto 32 slots).
So, as a solution, defer the bulk of the ISR processing to tasklet
context. Each CQ will have its down tasklet.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the hip06 and hip07 SoCs, the interrupt lines from the SAS
controllers are connected to mbigen hw module [1]. The mbigen module is
probed with module_init, and, as such, is not guaranteed to probe before
the SAS driver. So we need to support deferred probe.
We check for probe deferral in the hw layer probe, so we not probe into
the main layer and allocate shost, memories, etc., to later learn that
we need to defer the probe.
[1] ./Documentation/devicetree/bindings/interrupt-controller/hisilicon,mbigen-v2.txt
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>