We found smc_llc_send_link_delete_all() sometimes wait
for 2s timeout when testing with RDMA link up/down.
It is possible when a smc_link is in ACTIVATING state,
the underlaying QP is still in RESET or RTR state, which
cannot send any messages out.
smc_llc_send_link_delete_all() use smc_link_usable() to
checks whether the link is usable, if the QP is still in
RESET or RTR state, but the smc_link is in ACTIVATING, this
LLC message will always fail without any CQE entering the
CQ, and we will always wait 2s before timeout.
Since we cannot send any messages through the QP before
the QP enter RTS. I add a wrapper smc_link_sendable()
which checks the state of QP along with the link state.
And replace smc_link_usable() with smc_link_sendable()
in all LLC & CDC message sending routine.
Fixes: 5f08318f61 ("smc: connection data control (CDC)")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverity reports a possible NULL dereferencing problem:
in smc_vlan_by_tcpsk():
6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times).
7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next.
1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower);
CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS)
8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev.
1624 if (is_vlan_dev(ndev)) {
Remove the manual implementation and use netdev_walk_all_lower_dev() to
iterate over the lower devices. While on it remove an obsolete function
parameter comment.
Fixes: cb9d43f677 ("net/smc: determine vlan_id of stacked net_device")
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The link_id is supposed to be unique, but smcr_next_link_id() doesn't
skip the used link_id as expected. So the patch fixes this.
Fixes: 026c381fb4 ("net/smc: introduce link_idx for link group array")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC-R link down event is important to help us find links' issues, we
should track this event, especially in the single nic mode, which means
upper layer connection would be shut down. Then find out the direct
link-down reason in time, not only increased the counter, also the
location of the code who triggered this event.
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the netlink support for SMC-Rv2 related attributes that are
provided to user space.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the work request layer define one large v2 buffer for each link group
that is used to transmit and receive large LLC control messages.
Add the completion queue handling for this buffer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In smc_ib.c, scan for RoCE devices that support UDP encapsulation.
Find an eligible device and check that there is a route to the
remote peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the server side of the SMC-Rv2 processing. Process incoming
CLC messages, find eligible devices and check for a valid route to the
remote peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 8f3d65c166 ("net/smc: fix wait on already cleared link")
introduced link refcounting to avoid waits on already cleared links.
This patch extents and improves the refcounting to cover all
remaining possible cases for this kind of error situation.
Fixes: 15e1b99aad ("net/smc: no WR buffer wait for terminating link group")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The abort_work is scheduled when a connection was detected to be
out-of-sync after a link failure. The work calls smc_conn_kill(),
which calls smc_close_active_abort() and that might end up calling
smc_close_cancel_work().
smc_close_cancel_work() cancels any pending close_work and tx_work but
needs to release the sock_lock before and acquires the sock_lock again
afterwards. So when the sock_lock was NOT acquired before then it may
be held after the abort_work completes. Thats why the sock_lock is
acquired before the call to smc_conn_kill() in __smc_lgr_terminate(),
but this is missing in smc_conn_abort_work().
Fix that by acquiring the sock_lock first and release it after the
call to smc_conn_kill().
Fixes: b286a0651e ("net/smc: handle incoming CDC validation message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system EID is retrieved using an registered ISM device each time
when needed. This adds some unnecessary complexity at all places where
the system EID is needed, but no ISM device is at hand.
Simplify the code and save the system EID in a static variable in
smc_ism.c.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a3fe3d01bd ("net/smc: introduce sg-logic for RMBs") introduced
a restriction for RMB allocations as used by SMC-R. However, SMC-D does
not use scatter-gather lists to back its DMBs, yet it was limited by
this restriction, still.
This patch exempts SMC, but limits allocations to the maximum RMB/DMB
size respectively.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC clients may be assigned to a different link after the initial
connection between two peers was established. In such a case,
the connection counter was not correctly set.
Update the connection counter correctly when a smc client connection
is assigned to a different smc link.
Fixes: 07d51580ff ("net/smc: Add connection counters for links")
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Tested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the gathered SMC statistics network namespace aware, for each
namespace collect an own set of statistic information.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to collect SMC statistics information. Per-cpu
variables are used to collect the statistic information for better
performance and for reducing concurrency pitfalls. The code that is
collecting statistic data is implemented in macros to increase code
reuse and readability.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_lgr_cleanup() calls smcd_unregister_all_dmbs() as part of the link
group termination process. This is a leftover from the times when
smc_lgr_cleanup() scheduled a worker to actually free the link group.
Nowadays smc_lgr_cleanup() directly calls smc_lgr_free() without any
delay so an earlier dmb unregistration is no longer needed.
So remove smcd_unregister_all_dmbs() and the call to it.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using snprintf() to convert not null-terminated strings to null
terminated strings may cause out of bounds read in the source string.
Therefore use memcpy() and terminate the target string with a null
afterwards.
Fixes: a3db10efcc ("net/smc: Add support for obtaining SMCR device list")
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
smc_clc_get_hostname() sets the host pointer to a buffer
which is not NULL-terminated (see smc_clc_init()).
Reported-by: syzbot+f4708c391121cfc58396@syzkaller.appspotmail.com
Fixes: 099b990bd1 ("net/smc: Add support for obtaining system information")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce get link command which loops through
all available links of all available link groups. It
uses the SMC-R linkgroup list as entry point, not
the socket list, which makes linkgroup diagnosis
possible, in case linkgroup does not contain active
connections anymore.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce get linkgroup command which loops through
all available SMCR linkgroups. It uses the SMC-R linkgroup
list as entry point, not the socket list, which makes
linkgroup diagnosis possible, in case linkgroup does not
contain active connections anymore.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new netlink command to obtain system information
of the smc module.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During link creation add net-device ifindex and ib-device
name to link structure. This is needed for diagnostic purposes.
When diagnostic information is gathered, we need to traverse
device, linkgroup and link structures, to be able to do that
we need to hold a spinlock for the linkgroup list, without this
diagnostic information in link structure, another device list
mutex holding would be necessary to dereference the device
pointer in the link structure which would be impossible when
holding a spinlock already.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add link counters to the structure of the smc ib device, one counter per
ib port. Increase/decrease the counters as needed in the corresponding
routines.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add connection counters to the structure of the link.
Increase/decrease the counters as needed in the corresponding
routines.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the multi-subnet support of SMC-Dv2 the match for existing link
groups should not include the vlanid of the network device.
Set ini->smcd_version accordingly before the call to smc_conn_create()
and use this value in smc_conn_create() to skip the vlanid check.
Fixes: 5c21c4ccaf ("net/smc: determine accepted ISM devices")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The patch that repaired the invalid return code in smcd_new_buf_create()
missed to take care of errno ENOSPC which has a special meaning that no
more DMBEs can be registered on the device. Fix that by keeping this
errno value during the translation of the return code.
Fixes: 6b1bbf94ab ("net/smc: fix invalid return code in smcd_new_buf_create()")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
smc_ism_register_dmb() returns error codes set by the ISM driver which
are not guaranteed to be negative or in the errno range. Such values
would not be handled by ERR_PTR() and finally the return code will be
used as a memory address.
Fix that by using a valid negative errno value with ERR_PTR().
Fixes: 72b7f6c487 ("net/smc: unique reason code for exceeded max dmb count")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SMCD_DMBE_SIZES should include all valid DMBE buffer sizes, so the
correct value is 6 which means 1MB. With 7 the registration of an ISM
buffer would always fail because of the invalid size requested.
Fix that and set the value to 6.
Fixes: c6ba7c9ba4 ("net/smc: add base infrastructure for SMC-D and ISM")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SMC Version 2 defines a first contact extension for CLC accept
and CLC confirm. This patch covers sending and receiving of the
CLC first contact extension.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD Version 2 allows to propose up to 8 additional ISM devices
offered to the peer as candidates for SMCD communication.
This patch covers the server side, i.e. selection of an ISM device
matching one of the proposed ISM devices, that will be used for
CLC accept
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD Version 2 allows proposing of up to 8 ISM devices in addition
to the native ISM device of SMCD Version 1.
This patch prepares the struct smc_init_info to deal with these
additional 8 ISM devices.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 6 types of workers which exist per smc connection. 3 of them
are used for listen and handshake processing, another 2 are used for
close and abort processing and 1 is the tx worker that moves calls to
sleeping functions into a worker.
To prevent flooding of the system work queue when many connections are
opened or closed at the same time (some pattern uperf implements), move
those workers to one of 3 smc-specific work queues. Two work queues are
module-global and used for handshake and close workers. The third work
queue is defined per link group and used by the tx workers that may
sleep waiting for resources of this link group.
And in smc_llc_enqueue() queue the llc_event_work work to the system
prio work queue because its critical that this work is started fast.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_lgr_cleanup_early() schedules the free worker with delay. DMB
unregistering occurs in this delayed worker increasing the risk
to reach the SMCD SBA limit without need. Terminate the
linkgroup immediately, since termination means early DMB unregistering.
For SMCD the global smc_server_lgr_pending lock is given up early.
A linkgroup to be given up with smc_lgr_cleanup_early() may already
contain more than one connection. Using __smc_lgr_terminate() in
smc_lgr_cleanup_early() covers this.
And consolidate smc_ism_put_vlan() and smc_put_device() into smc_lgr_free()
only.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_clc_send_accept() and smc_clc_send_confirm() are quite similar.
Move common code into a separate function smc_clc_send_confirm_accept().
And introduce separate SMCD and SMCR struct definitions for CLC accept
resp. confirm.
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Field names "srv_first_contact" and "cln_first_contact" are misleading,
since they apply to both, server and client. Rename them to
"first_contact_peer" and "first_contact_local".
Rename "ism_gid" by the more precise name "ism_peer_gid".
Rename version constant "SMC_CLC_V1" into "SMC_V1".
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC tries to make use of SMCD first. If a problem shows up,
it tries to switch to SMCR. If the SMCD initializing problem shows
up after the SMCD connection has already been initialized, field
rx_off keeps the wrong SMCD value for SMCR, which results in corrupted
data at the receiver.
This patch adds an explicit (re-)setting of field rx_off to zero if the
connection uses SMCR.
Fixes: be244f28d2 ("net/smc: add SMC-D support in data transfer")
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the maximum dmb buffer limit for an ism device is reached no more
dmb buffers can be registered. When this happens the reason code is set
to SMC_CLC_DECL_MEM indicating out-of-memory. This is the same reason
code that is used when no memory could be allocated for the new dmb
buffer.
This is confusing for users when they see this error but there is more
memory available. To solve this set a separate new reason code when the
maximum dmb limit exceeded.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a current limit of 1920 registered dmb buffers per ISM device
for smc-d. One link group can contain 255 connections, each connection
is using one dmb buffer. When the connection is closed then the
registered buffer is held in a queue and is reused by the next
connection. When a link group is 'full' then another link group is
created and uses an own buffer pool. The link groups are added to a
list using list_add() which puts a new link group to the first position
in the list.
In the situation that many connections are opened (>1920) and a few of
them stay open while others are closed quickly we end up with at least 8
link groups. For a new connection a matching link group is looked up,
iterating over the list of link groups. The trailing 7 link groups
all have registered dmb buffers which could be reused, while the first
link group has only a few dmb buffers and then hit the 1920 limit.
Because the first link group is not full (255 connection limit not
reached) it is chosen and finally the connection falls back to TCP
because there is no dmb buffer available in this link group.
There are multiple ways to fix that: using list_add_tail() allows
to scan older link groups first for free buffers which ensures that
buffers are reused first. This fixes the problem for smc-r link groups
as well. For smc-d there is an even better way to address this problem
because smc-d does not have the 255 connections per link group limit.
So fix the problem for smc-d by allowing large link groups.
Fixes: c6ba7c9ba4 ("net/smc: add base infrastructure for SMC-D and ISM")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two buffers are allocated for each SMC connection. Each buffer is
added to a buffer list after creation. When the second buffer
allocation fails, the first buffer is freed but not deleted from
the list. This might result in crashes when another connection picks
up the freed buffer later and starts to work with it.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 6511aad3f0 ("net/smc: change smc_buf_free function parameters")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma related ...sync_sg... functions check the link state before the
dma function is actually called. But the check in smc_link_usable()
allows links in ACTIVATING state which are not yet mapped to dma memory.
Under high load it may happen that the sync_sg functions are called for
such a link which results in an debug output like
DMA-API: mlx5_core 0002:00:00.0: device driver tries to sync
DMA memory it has not allocated [device address=0x0000000103370000]
[size=65536 bytes]
To fix that introduce a helper to check for the link state ACTIVE and
use it where appropriate. And move the link state update to ACTIVATING
to the end of smcr_link_init() when most initial setup is done.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: d854fcbfae ("net/smc: add new link state and related helpers")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new ib device is up smc will send an add link invitation to the
peer if needed. This is currently done with rudimentary flow control.
Under high workload these add link invitations can disturb other llc
flows because they arrive unexpected. Fix this by integrating the
invitations into the normal llc event flow and handle them as a flow.
While at it, check for already assigned requests in the flow before
the new add link request is assigned.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 1f90a05d9f ("net/smc: add smcr_port_add() and smcr_link_up() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a link-down condition we notify the SMC server and expect that the
server will finally trigger the link clear processing on the client
side. This could fail when anything along this notification path goes
wrong. Clear the link as part of SMC client link-down processing to
prevent dangling links.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 541afa10c1 ("net/smc: add smcr_port_err() and smcr_link_down() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
