This adds sufficient changes to allow VFs l2-configuration flows to work.
While the fastpath of the VF and the PF are meant to be exactly the same,
the configuration of the VF is done by the PF.
This diverges all VF-related configuration flows that originate from a VF,
making them pass through the VF->PF channel and adding sufficient logic
on the PF side to support them.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Communication between VF and PF is based on a dedicated HW channel;
VF will prepare a messge, and by signaling the HW the PF would get a
notification of that message existance. The PF would then copy the
message, process it and DMA an answer back to the VF as a response.
The messages themselves are TLV-based - allowing easier backward/forward
compatibility.
This patch adds the infrastructure of the channel on the PF side -
starting with the arrival of the notification and ending with DMAing
the response back to the VF.
It also adds a dummy-response as reference, as it only lays the
groundwork of the communication; it doesn't really add support of any
actual messages.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a new Kconfig option for qed* driver which would allow
[eventually] the support in VFs.
This patch adds the necessary logic in the PF to learn about the possible
VFs it will have to support [Based on PCI configuration space and HW],
and prepare a database with an entry per-VF as infrastructure for future
interaction with said VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Add workaround to detect bad opaque in rx completion.
2-part workaround for this hardware bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add detection and recovery code when the hardware returned opaque value
does not match the expected consumer index. Once the issue is detected,
we skip the processing of all RX and LRO/GRO packets. These completion
entries are discarded without sending the SKB to the stack and without
producing new buffers. The function will be reset from a workqueue.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a rare hardware bug that can cause a bad opaque value in the RX
or TPA completion. When this happens, the hardware may have used the
same buffer twice for 2 rx packets. In addition, the driver will also
crash later using the bad opaque as the index into the ring.
The rx opaque value is predictable and is always monotonically increasing.
The workaround is to keep track of the expected next opaque value and
compare it with the one returned by hardware during RX and TPA start
completions. If they miscompare, we will not process any more RX and
TPA completions and exit NAPI. We will then schedule a workqueue to
reset the function.
This patch adds the logic to keep track of the next rx consumer index.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qlcnic_fw_cmd_get_minidump_temp() fails then "fw_dump->tmpl_hdr" is
NULL or possibly freed. It can lead to an oops later.
Fixes: d01a6d3c8a ('qlcnic: Add support to enable capability to extend minidump for iSCSI')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two some radeon display fixes.
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix PLL sharing on DCE6.1 (v2)
drm/radeon: fix DP link training issue with second 4K monitor
Misc intel fixes, reverting MST audio which was causing oops for now.
* tag 'drm-intel-fixes-2016-05-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Bail out of pipe config compute loop on LPT
Revert "drm/i915: start adding dp mst audio"
drm/i915/bdw: Add missing delay during L3 SQC credit programming
drm/i915/lvds: separate border enable readout from panel fitter
drm/i915: Update CDCLK_FREQ register on BDW after changing cdclk frequency
This is the first NFC pull request for 4.7. With this one we
mainly have:
- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
microcontroller as the pn533, but it talks to the host through i2c
instead of USB. By separating the pn533 driver into core and PHY
parts, we can not add the i2c layer and support the pn532 chipset.
- Support for NCI's loopback mode. This is a testing mode where each
packet received by the NFCC is sent back to the DH, allowing the
host to test that the controller can receive and send data.
- A few ACPI related fixes for the STMicro drivers, in order to match
the device tree naming scheme.
- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zM22
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.7 pull request
This is the first NFC pull request for 4.7. With this one we
mainly have:
- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
microcontroller as the pn533, but it talks to the host through i2c
instead of USB. By separating the pn533 driver into core and PHY
parts, we can not add the i2c layer and support the pn532 chipset.
- Support for NCI's loopback mode. This is a testing mode where each
packet received by the NFCC is sent back to the DH, allowing the
host to test that the controller can receive and send data.
- A few ACPI related fixes for the STMicro drivers, in order to match
the device tree naming scheme.
- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox 100G mlx5 CQE compression
Introducing ConnectX-4 CQE (Completion Queue Entry) compression feature
for mlx5 etherent driver.
CQE Compressing reduces PCI overhead by coalescing and compressing multiple CQEs into a
single merged CQE. Successful compressing improves message rate especially for small packet
traffic.
CQE Compressing in details:
Instead of writing full CQEs to memory, multiple almost identical CQEs are merged and compressed.
Information that is shared between the CQEs is written once, regardless of the number of
compressed CQEs. In addition, only the unique information (small amount of bytes compared to
full CQE size) is written per CQE.
CQE Compression Block:
This block contains multiple compressed CQEs. CQE Compression Block contains a single copy
of CQEs properties which are shared between all the compressed CQEs (called Title, see below)
and multiple mini CQEs (CQEs in compressed form).
Title:
The Title holds information which is shared between all the compressed CQEs in the CQE Compression
Block. In each Compression Block there is only a single Title regardless of the number
of compressed CQEs.
Mini CQE:
A CQE in compressed form that holds some data needed to extract a single full CQE, for example
8 Bytes instead of 64 Bytes.
The shared information between all compressed CQEs, which belong to the same CQE Compression
Block called Title, is written once, and only the unique information in each compressed
CQE, for example 8 bytes, is written per compressed CQE, called mini CQE.
Since CQE Compression can add overhead to the software (CPU),
it will be only enabled on "weak/slow" PCI slots, where it can actually help.
Applied on top: c047c3b1af ('netfilter: conntrack: remove uninitialized shadow variable')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We turn the feature ON, only for servers with PCI BW < MAX LINK BW, as it
helps reducing PCI pressure on weak PCI slots, but it adds some software
overhead.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the MPWQE/Striding RQ default configuration dynamic and not
statically set at compile time. Now at driver load we set
stride size and num strides dynamically.
By default we use same values as before, but when CQE compression
is enabled, we set larger stride size to benefit from CQE
compression for larger packets.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CQE compression feature is meant to save PCIe bandwidth by
compressing few CQEs into smaller amount of bytes on PCIe.
CQE compression can be selectively enabled per CQ. By default
is disabled for now and will be enabled later on.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
More enabler patches for DSA probing
The complete set of patches for the reworked DSA probing is too big to
post as once. These subset contains some enablers which are easy to
review.
Eventually, the Marvell driver will instantiate its own internal MDIO
bus, rather than have the framework do it, thus allows devices on the
bus to be listed in the device tree. Initialize the main mutex as soon
as it is created, to avoid lifetime issues with the mdio bus.
A previous patch renamed all the DSA probe functions to make room for
a true device probe. However the recent merging of all the Marvell
switch drivers resulted in mv88e6xxx going back to the old probe
name. Rename it again, so we can have a driver probe function.
Add minimum support for the Marvell switch driver to probe as an MDIO
device, as well as an DSA driver. Later patches will then register
this device with the new DSA core framework.
Move the GPIO reset code out of the DSA code. Different drivers may
need different reset mechanisms, e.g. via a reset controller for
memory mapped devices. Don't clutter up the core with this. Let each
driver implement what it needs.
master_dev is no longer needed in the switch drivers, since they have
access to a device pointer from the probe function. Remove it.
Let the switch parse the eeprom length from its one device tree
node. This is required with the new binding when the central DSA
platform device no longer exists.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A switch can export an attached EEPROM using the standard ethtool API.
However the switch itself cannot determine the size of the EEPROM, and
multiple sizes are allowed. Thus a device tree property is supported
to indicate the length of the EEPROM. Parse this property during
device probe, and implement a callback function to retrieve it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch drivers only use the master_dev member for dev_info()
messages. Now that the device is passed to the old style probe, and
new style drivers are probed as true linux drivers, this is no longer
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.
There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow Marvell switches to be mdio devices. Currently the driver just
allocate the private structure and detects what device is on the
bus. Later patches will make them register with the DSA framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All other DSA drivers use _drv_ in there DSA probe function name, thus
allowing for a true linux driver probe function to use the
conventional name. Make mv88e6xxx fit this pattern.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By initialising immediately it, we don't run the danger of using it
before it is initialised.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch models have a STU (per VLAN port state database). Add a new
capability flag to switches info, instead of checking their family.
Also if the 6165 family has an STU, it must have a VTU, so add the
MV88E6XXX_FLAG_VTU to its family flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both VTU and STU operations use the same routine to access their
(common) data registers, with a different offset.
Add VTU and STU specific read and write functions to the data registers
to abstract the required offset.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: vrf: Fixup PKTINFO to return enslaved device index
Applications such as OSPF and BFD need the original ingress device not
the VRF device; the latter can be derived from the former. To that end
move the packet intercept from an rx handler that is invoked by
__netif_receive_skb_core to the ipv4 and ipv6 receive processing.
IPv6 already saves the skb_iif to the control buffer in ipv6_rcv. Since
the skb->dev has not been switched the cb has the enslaved device. Make
the same happen for IPv4 by adding the skb_iif to inet_skb_parm and set
it in ipv4 code after clearing the skb control buffer similar to IPv6.
From there the pktinfo can just pull it from cb with the PKTINFO_SKB_CB
cast.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications such as OSPF and BFD need the original ingress device not
the VRF device; the latter can be derived from the former. To that end
add the skb_iif to inet_skb_parm and set it in ipv4 code after clearing
the skb control buffer similar to IPv6. From there the pktinfo can just
pull it from cb with the PKTINFO_SKB_CB cast.
The previous patch moving the skb->dev change to L3 means nothing else
is needed for IPv6; it just works.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the VRF driver uses the rx_handler to switch the skb device
to the VRF device. Switching the dev prior to the ip / ipv6 layer
means the VRF driver has to duplicate IP/IPv6 processing which adds
overhead and makes features such as retaining the ingress device index
more complicated than necessary.
This patch moves the hook to the L3 layer just after the first NF_HOOK
for PRE_ROUTING. This location makes exposing the original ingress device
trivial (next patch) and allows adding other NF_HOOKs to the VRF driver
in the future.
dev_queue_xmit_nit is exported so that the VRF driver can cycle the skb
with the switched device through the packet taps to maintain current
behavior (tcpdump can be used on either the vrf device or the enslaved
devices).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol for 4in6 tunnel is IPPROTO_IPIP. This was wrongly changed by
the last cleanup.
CC: Tom Herbert <tom@herbertland.com>
Fixes: 0d3c703a9d ("ipv6: Cleanup IPv6 tunnel receive path")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a couple of small fixes: one is a potential uninitialised
error variable in the alua code, potentially causing spurious failures
and the other is a problem caused by the conversion of SCSI to
hostwide tags which resulted in the qla1280 driver always failing in
host initialisation.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJXM48uAAoJEDeqqVYsXL0MoXQH/2G/twARSNucNf0F/YW5dJL7
kY7yPk+HL7iz+Y/B6N6x/fGYKvlzg/Slum+rsCoDMYnkJCA+vwvWOeKvBDaEN3QJ
NrdJsOhhVkL1Vod6l7YnXxHq1spC+z1B6v6ixe/UsjevvZpi4Px8HtaZPhW5gM5Z
ha4vL5MS3FCpXs1p5haYT9VO3c0sxLSz7L/MiXA/zcBgsgegJGDUav1tgLzj8Sv+
36SdacJdooFPYLrPt1992B/lP56piuAXhkqi/X3y3oyO3rBhpJ6evSUEGN3/+wlm
hhZMoB5jiOTAZHIXNICI6qrJh1MLIBE4A+C8Hs/yzojhQvd1cd2S5X1OfoqVDr4=
=szZw
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a couple of small fixes: one is a potential uninitialised
error variable in the alua code, potentially causing spurious failures
and the other is a problem caused by the conversion of SCSI to
hostwide tags which resulted in the qla1280 driver always failing in
host initialisation"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
qla1280: Don't allocate 512kb of host tags
scsi_dh_alua: uninitialized variable in alua_rtpg()
Pull networking fixes from David Miller:
"Hopefully the last round of fixes this release, fingers crossed :)
1) Initialize static nf_conntrack_locks_all_lock properly, from
Florian Westphal.
2) Need to cancel pending work when destroying IDLETIMER entries,
from Liping Zhang.
3) Fix TX param usage when sending TSO over iwlwifi devices, from
Emmanuel Grumbach.
4) NFACCT quota params not validated properly, from Phil Turnbull.
5) Resolve more glibc vs. kernel header conflicts, from Mikko
Tapeli.
6) Missing IRQ free in ravb_close(), from Geert Uytterhoeven.
7) Fix infoleak in x25, from Kangjie Lu.
8) Similarly in thunderx driver, from Heinrich Schuchardt.
9) tc_ife.h uapi header not exported properly, from Jamal Hadi Salim.
10) Don't reenable PHY interreupts if device is in polling mode, from
Shaohui Xie.
11) Packet scheduler actions late binding was not being handled
properly at all, from Jamal Hadi Salim.
12) Fix binding of conntrack entries to helpers in openvswitch, from
Joe Stringer"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
gre: do not keep the GRE header around in collect medata mode
openvswitch: Fix cached ct with helper.
net sched: ife action fix late binding
net sched: skbedit action fix late binding
net sched: simple action fix late binding
net sched: mirred action fix late binding
net sched: ipt action fix late binding
net sched: vlan action fix late binding
net: phylib: fix interrupts re-enablement in phy_start
tcp: refresh skb timestamp at retransmit time
net: nps_enet: bug fix - handle lost tx interrupts
net: nps_enet: Tx handler synchronization
export tc ife uapi header
net: thunderx: avoid exposing kernel stack
net: fix a kernel infoleak in x25 module
ravb: Add missing free_irq() call to ravb_close()
uapi glibc compat: fix compile errors when glibc net/if.h included before linux/if.h
netfilter: nfnetlink_acct: validate NFACCT_QUOTA parameter
iwlwifi: mvm: don't override the rate with the AMSDU len
netfilter: IDLETIMER: fix race condition when destroy the target
...
For ipgre interface in collect metadata mode, it doesn't make sense for the
interface to be of ARPHRD_IPGRE type. The outer header of received packets
is not needed, as all the information from it is present in metadata_dst. We
already don't set ipgre_header_ops for collect metadata interfaces, which is
the only consumer of mac_header pointing to the outer IP header.
Just set the interface type to ARPHRD_NONE in collect metadata mode for
ipgre (not gretap, that still correctly stays ARPHRD_ETHER) and reset
mac_header.
Fixes: a64b04d86d ("gre: do not assign header_ops in collect metadata mode")
Fixes: 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using conntrack helpers from OVS, a common configuration is to
perform a lookup without specifying a helper, then go through a
firewalling policy, only to decide to attach a helper afterwards.
In this case, the initial lookup will cause a ct entry to be attached to
the skb, then the later commit with helper should attach the helper and
confirm the connection. However, the helper attachment has been missing.
If the user has enabled automatic helper attachment, then this issue
will be masked as it will be applied in init_conntrack(). It is also
masked if the action is executed from ovs_packet_cmd_execute() as that
will construct a fresh skb.
This patch fixes the issue by making an explicit call to try to assign
the helper if there is a discrepancy between the action's helper and the
current skb->nfct.
Fixes: cae3a26275 ("openvswitch: Allow attaching helpers to ct action")
Signed-off-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace 2 arguments (cnt and rtt) in the congestion control modules'
pkts_acked() function with a struct. This will allow adding more
information without having to modify existing congestion control
modules (tcp_nv in particular needs bytes in flight when packet
was sent).
As proposed by Neal Cardwell in his comments to the tcp_nv patch.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The x86 exception table sorting was changed in commit 29934b0fb8
("x86/extable: use generic search and sort routines") to use the arch
independent code in lib/extable.c. However, the patch was mangled
somehow on its way into the kernel from the last version posted at [1].
The committed version kind of attempted to incorporate the changes of
commit 548acf1923 ("x86/mm: Expand the exception table logic to allow
new handling options") as in _completely_ _ignoring_ the x86 specific
'handler' member of struct exception_table_entry. This effectively
broke the sorting as entries will only partly be swapped now.
Fortunately, the x86 Kconfig selects BUILDTIME_EXTABLE_SORT, so the
exception table doesn't need to be sorted at runtime. However, in case
that ever changes, we better not break the exception table sorting just
because of that.
[ Ard Biesheuvel points out that BUILDTIME_EXTABLE_SORT applies to the
core image only, but we still rely on the sorting routines for modules
in that case - Linus ]
Fix this by providing a swap_ex_entry_fixup() macro that takes care of
the 'handler' member.
[1] https://lkml.org/lkml/2016/1/27/232
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Fixes: 29934b0fb8 ("x86/extable: use generic search and sort routines")
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A bunch of small driver specific fixes that have come up, none of them
remarkable in themselves. One fixes a regression introduced in the
merge window and another two are targetted at stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXM1aPAAoJECTWi3JdVIfQ6OEH/i0K+0N0KLHNznOgyk5F6KTZ
kSg03F03UBs66CWVcFEWGtWTBLqlYpmQptJqPSZtOVu99zcVfX8PB+tjWM7zfo/F
cxMVeyiflf/9jiFSH/qXnLDOYKLMBVonv0laS2U0wjLME5UF+kGJfPr9F1w/2uzN
N8KpkHFkdprzuIV9JGqB4CXiZqyDrH+6yV3jIQh1GTeN4DiDST3/tLPkqpETxCHz
/ayfsofi5PLA9126Ogn1De8dds65HTbPTrJbf0jMiH3SGFXsLLK5clDMN9g7aNwK
9Chc75akHsjcdKPEANnR9KmAeZpL53n5nQp8iHoYLPqSlaVeJPVkhrE5yZqbrUc=
=KyrG
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A bunch of small driver specific fixes that have come up, none of them
remarkable in themselves. One fixes a regression introduced in the
merge window and another two are targetted at stable"
* tag 'spi-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: Do not detect number of enabled chip selects on Intel SPT
spi: spi-ti-qspi: Handle truncated frames properly
spi: spi-ti-qspi: Fix FLEN and WLEN settings if bits_per_word is overridden
spi: omap2-mcspi: Undo broken fix for dma transfer of vmalloced buffer
spi: spi-fsl-dspi: Fix cs_change handling in message transfer
an objtool warning for CONFIG_PROFILE_ALL_BRANCHES.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXM0h+AAoJEL/70l94x66DhjwH/2l24ouNC32DJGoY511yWogF
QrBrmQnnT1r+v9IDCC5ITCCkJp+EPF0uFwLI+T6URzRdSdNUN/EqYymUyhsICWwb
9xIsR9VraeB4OhH5IMps1Pkwyx6FMjeVqvVx8dib+NUQpV2o5KxkkFsE9oIX7mtA
PgwRaLsV8MFZH06g/qvwYPs5NNUecQU8AFCAps0PzWSXG6KHmzsjJZjsXbDhb3n4
oOGJTLXlRS+SSOWFjngYJNIQ7Z8V1WHM6qftZXtcDWIFbq8CuWn9dZR2WhpUu+nK
J/I5WC99stxgljFOjI/zdPKQbRy0eBQyDAPHAblDo83vSKsDRgYGX3608gGz3xY=
=s75+
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Two small x86 patches, improving "make kvmconfig" and fixing an
objtool warning for CONFIG_PROFILE_ALL_BRANCHES"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvmconfig: add more virtio drivers
x86/kvm: Add stack frame dependency to fastop() inline asm
Phoenix Audio has yet another device with another id (even a different
vendor id, 0556:0014) that requires the same quirk for the sample
rate.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The memory range assigned to the PMC (Power Management Controller) was
not including the PMC_PCR register which are used to control peripheral
clocks.
This was working fine thanks to the page granularity of ioremap(), but
started to fail when we switched to syscon/regmap, because regmap is
making sure that all accesses are falling into the reserved range.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 863a81c3be ("clk: at91: make use of syscon to share PMC registers in several drivers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The HDMI/DP audio output on ATI/AMD chips got broken due to the recent
restructuring of chmap. Fortunately, Daniel Exner could bisect, and
pointed the culprit commit [739ffee97e: ALSA: hda - Add hdmi chmap
verb programming ops to chmap object].
This commit moved some ops from hdmi_ops to chmap_ops, and reassigned
the ops in the embedded chmap object in hdmi_spec instead.
Unfortunately, the reassignment of these ops in patch_atihdmi() were
moved into an if block that is performed only for old chips. Thus, on
newer chips, the generic ops is still used, which doesn't work for
such ATI/AMD chips.
This patch addresses the regression, simply by moving the assignment
of chmap ops to the right place.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114981
Fixes: 739ffee97e ('ALSA: hda - Add hdmi chmap verb programming ops to chmap object')
Reported-and-tested-by: Daniel Exner <dex@dragonslave.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mike reported that this recent commit:
3a47d5124a ("sched/fair: Fix fairness issue on migration")
... broke interactivity and the signal starvation test.
We have a proper fix series in the works but ran out of time for
v4.6, so revert the commit.
Reported-by: Mike Galbraith <efault@gmx.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Generally permission checking is not necessary when overlayfs looks up a
dentry on one of the underlying layers, since search permission on base
directory was already checked in ovl_permission().
More specifically using lookup_one_len() causes a problem when the lower
directory lacks search permission for a specific user while the upper
directory does have search permission. Since lookups are cached, this
causes inconsistency in behavior: success depends on who did the first
lookup.
So instead use lookup_hash() which doesn't do the permission check.
Reported-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Overlayfs needs lookup without inode_permission() and already has the name
hash (in form of dentry->d_name on overlayfs dentry). It also doesn't
support filesystems with d_op->d_hash() so basically it only needs
the actual hashed lookup from lookup_one_len_unlocked()
So add a new helper that does unlocked lookup of a hashed name.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
If a file is renamed to a hardlink of itself POSIX specifies that rename(2)
should do nothing and return success.
This condition is checked in vfs_rename(). However it won't detect hard
links on overlayfs where these are given separate inodes on the overlayfs
layer.
Overlayfs itself detects this condition and returns success without doing
anything, but then vfs_rename() will proceed as if this was a successful
rename (detach_mounts(), d_move()).
The correct thing to do is to detect this condition before even calling
into overlayfs. This patch does this by calling vfs_select_inode() to get
the underlying inodes.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org> # v4.2+
Jamal Hadi Salim says:
====================
Some actions were broken in allowing for late binding of actions.
Late binding workflow is as follows:
a) create an action and provide all necessary parameters for it
Optionally provide an index or let the kernel give you one.
Example:
sudo tc actions add action police rate 1kbit burst 90k drop index 1
b) later on bind to the pre-created action from a filter definition
by merely specifying the index.
Example:
sudo tc filter add dev lo parent ffff: protocol ip prio 8 \
u32 match ip src 127.0.0.8/32 flowid 1:8 action police index 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
