Now that the hd_struct always has a block device attached to it, there is
no need for having two size field that just get out of sync.
Additionally the field in hd_struct did not use proper serialization,
possibly allowing for torn writes. By only using the block_device field
this problem also gets fixed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Coly Li <colyli@suse.de> [bcache]
Acked-by: Chao Yu <yuchao0@huawei.com> [f2fs]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To simplify block device lookup and a few other upcoming areas, make sure
that we always have a struct block_device available for each disk and
each partition, and only find existing block devices in bdget. The only
downside of this is that each device and partition uses a little more
memory. The upside will be that a lot of code can be simplified.
With that all we need to look up the block device is to lookup the inode
and do a few sanity checks on the gendisk, instead of the separate lookup
for the gendisk. For blk-cgroup which wants to access a gendisk without
opening it, a new blkdev_{get,put}_no_open low-level interface is added
to replace the previous get_gendisk use.
Note that the change to look up block device directly instead of the two
step lookup using struct gendisk causes a subtile change in behavior:
accessing a non-existing partition on an existing block device can now
cause a call to request_module. That call is harmless, and in practice
no recent system will access these nodes as they aren't created by udev
and static /dev/ setups are unusual.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a preparation patch to have minimal block layer request bio
append functionality in the context of the NVMeOF Passthru driver which
falls in the fast path and doesn't need calls from blk_rq_append_bio().
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move blk_mq_sched_try_merge to blk-merge.c, which allows to mark
a lot of the merge infrastructure static there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Also move the definition from the public blkdev.h to the private
block/blk.h header.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Also move the definition from the public blkdev.h to the private
block/blk.h header.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are lots of duplicated code when trying to merge a bio from
plug list and sw queue, we can introduce a new helper to attempt
to merge a bio, which can simplify the blk_bio_list_merge()
and blk_attempt_plug_merge().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the blk_mq_bio_list_merge() into blk-merge.c and
rename it as a generic name.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch improves discard bio split for address and size alignment in
__blkdev_issue_discard(). The aligned discard bio may help underlying
device controller to perform better discard and internal garbage
collection, and avoid unnecessary internal fragment.
Current discard bio split algorithm in __blkdev_issue_discard() may have
non-discarded fregment on device even the discard bio LBA and size are
both aligned to device's discard granularity size.
Here is the example steps on how to reproduce the above problem.
- On a VMWare ESXi 6.5 update3 installation, create a 51GB virtual disk
with thin mode and give it to a Linux virtual machine.
- Inside the Linux virtual machine, if the 50GB virtual disk shows up as
/dev/sdb, fill data into the first 50GB by,
# dd if=/dev/zero of=/dev/sdb bs=4096 count=13107200
- Discard the 50GB range from offset 0 on /dev/sdb,
# blkdiscard /dev/sdb -o 0 -l 53687091200
- Observe the underlying mapping status of the device
# sg_get_lba_status /dev/sdb -m 1048 --lba=0
descriptor LBA: 0x0000000000000000 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000000000800 blocks: 16773120 deallocated
descriptor LBA: 0x0000000000fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000001000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000017ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000001800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000001fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000002000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000027ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000002800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000002fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000003000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000037ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000003800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000003fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000004000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000047ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000004800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000004fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000005000000 blocks: 8386560 deallocated
descriptor LBA: 0x00000000057ff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000005800000 blocks: 8386560 deallocated
descriptor LBA: 0x0000000005fff800 blocks: 2048 mapped (or unknown)
descriptor LBA: 0x0000000006000000 blocks: 6291456 deallocated
descriptor LBA: 0x0000000006600000 blocks: 0 deallocated
Although the discard bio starts at LBA 0 and has 50<<30 bytes size which
are perfect aligned to the discard granularity, from the above list
these are many 1MB (2048 sectors) internal fragments exist unexpectedly.
The problem is in __blkdev_issue_discard(), an improper algorithm causes
an improper bio size which is not aligned.
25 int __blkdev_issue_discard(struct block_device *bdev, sector_t sector,
26 sector_t nr_sects, gfp_t gfp_mask, int flags,
27 struct bio **biop)
28 {
29 struct request_queue *q = bdev_get_queue(bdev);
[snipped]
56
57 while (nr_sects) {
58 sector_t req_sects = min_t(sector_t, nr_sects,
59 bio_allowed_max_sectors(q));
60
61 WARN_ON_ONCE((req_sects << 9) > UINT_MAX);
62
63 bio = blk_next_bio(bio, 0, gfp_mask);
64 bio->bi_iter.bi_sector = sector;
65 bio_set_dev(bio, bdev);
66 bio_set_op_attrs(bio, op, 0);
67
68 bio->bi_iter.bi_size = req_sects << 9;
69 sector += req_sects;
70 nr_sects -= req_sects;
[snipped]
79 }
80
81 *biop = bio;
82 return 0;
83 }
84 EXPORT_SYMBOL(__blkdev_issue_discard);
At line 58-59, to discard a 50GB range, req_sects is set as return value
of bio_allowed_max_sectors(q), which is 8388607 sectors. In the above
case, the discard granularity is 2048 sectors, although the start LBA
and discard length are aligned to discard granularity, req_sects never
has chance to be aligned to discard granularity. This is why there are
some still-mapped 2048 sectors fragment in every 4 or 8 GB range.
If req_sects at line 58 is set to a value aligned to discard_granularity
and close to UNIT_MAX, then all consequent split bios inside device
driver are (almostly) aligned to discard_granularity of the device
queue. The 2048 sectors still-mapped fragment will disappear.
This patch introduces bio_aligned_discard_max_sectors() to return the
the value which is aligned to q->limits.discard_granularity and closest
to UINT_MAX. Then this patch replaces bio_allowed_max_sectors() with
this new routine to decide a more proper split bio length.
But we still need to handle the situation when discard start LBA is not
aligned to q->limits.discard_granularity, otherwise even the length is
aligned, current code may still leave 2048 fragment around every 4GB
range. Therefore, to calculate req_sects, firstly the start LBA of
discard range is checked (including partition offset), if it is not
aligned to discard granularity, the first split location should make
sure following bio has bi_sector aligned to discard granularity. Then
there won't be still-mapped fragment in the middle of the discard range.
The above is how this patch improves discard bio alignment in
__blkdev_issue_discard(). Now with this patch, after discard with same
command line mentiond previously, sg_get_lba_status returns,
descriptor LBA: 0x0000000000000000 blocks: 106954752 deallocated
descriptor LBA: 0x0000000006600000 blocks: 0 deallocated
We an see there is no 2048 sectors segment anymore, everything is clean.
Reported-and-tested-by: Acshai Manoj <acshai.manoj@microfocus.com>
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Enzo Matsumiya <ematsumiya@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move .nr_active update and request assignment into blk_mq_get_driver_tag(),
all are good to do during getting driver tag.
Meantime blk-flush related code is simplified and flush request needn't
to update the request table manually any more.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The make_request_fn is a little weird in that it sits directly in
struct request_queue instead of an operation vector. Replace it with
a block_device_operations method called submit_bio (which describes much
better what it does). Also remove the request_queue argument to it, as
the queue can be derived pretty trivially from the bio.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The queue can be trivially derived from the bio, so pass one less
argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move .nr_active update and request assignment into blk_mq_get_driver_tag(),
all are good to do during getting driver tag.
Meantime blk-flush related code is simplified and flush request needn't
to update the request table manually any more.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blkcg_bio_issue_check is a giant inline function that does three entirely
different things. Factor out the blk-cgroup related bio initalization
into a new helper, and the open code the sequence in the only caller,
relying on the fact that all the actual functionality is stubbed out for
non-cgroup builds.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We were only creating the request_queue debugfs_dir only
for make_request block drivers (multiqueue), but never for
request-based block drivers. We did this as we were only
creating non-blktrace additional debugfs files on that directory
for make_request drivers. However, since blktrace *always* creates
that directory anyway, we special-case the use of that directory
on blktrace. Other than this being an eye-sore, this exposes
request-based block drivers to the same debugfs fragile
race that used to exist with make_request block drivers
where if we start adding files onto that directory we can later
run a race with a double removal of dentries on the directory
if we don't deal with this carefully on blktrace.
Instead, just simplify things by always creating the request_queue
debugfs_dir on request_queue registration. Rename the mutex also to
reflect the fact that this is used outside of the blktrace context.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the call to blk_should_fake_timeout out of blk_mq_complete_request
and into the drivers, skipping call sites that are obvious error
handlers, and remove the now superflous blk_mq_force_complete_rq helper.
This ensures we don't keep injecting errors into completions that just
terminate the Linux request after the hardware has been reset or the
command has been aborted.
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For optimized block readers not holding a mutex, the "number of sectors"
64-bit value is protected from tearing on 32-bit architectures by a
sequence counter.
Disable preemption before entering that sequence counter's write side
critical section. Otherwise, the read side can preempt the write side
section and spin for the entire scheduler tick. If the reader belongs to
a real-time scheduling class, it can spin forever and the kernel will
livelock.
Fixes: c83f6bf98d ("block: add partition resize function to blkpg ioctl")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After the commit 5addeae1be ("blk-cgroup: remove blkcg_drain_queue"),
there is no caller of blk_throtl_drain, so let's remove it.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the non-"new_io" branch of blk_account_io_start() into separate
function. Fix merge accounting for discards (they were counted as write
merges).
The new blk_account_io_merge_bio() doesn't call update_io_ticks() unlike
blk_account_io_start(), as there is no reason for that.
[hch: rebased]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
percpu variables have a perfectly fine working stub implementation
for UP kernels, so use that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All callers are in blk-core.c, so move update_io_ticks over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The flush_queue_delayed was introdued to hold queue if flush is
running for non-queueable flush drive by commit 3ac0cc4508
("hold queue if flush is running for non-queueable flush drive"),
but the non mq parts of the flush code had been removed by
commit 7e992f847a ("block: remove non mq parts from the flush code"),
as well as removing the usage of the flush_queue_delayed flag.
Thus remove the unused flush_queue_delayed flag.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
part_inc_in_flight and part_dec_in_flight only have one caller each, and
those callers are purely for bio based drivers. Merge each function into
the only caller, and remove the superflous blk-mq checks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_mq_make_request currently needs to grab an q_usage_counter
reference when allocating a request. This is because the block layer
grabs one before calling blk_mq_make_request, but also releases it as
soon as blk_mq_make_request returns. Remove the blk_queue_exit call
after blk_mq_make_request returns, and instead let it consume the
reference. This works perfectly fine for the block layer caller, just
device mapper needs an extra reference as the old problem still
persists there. Open code blk_queue_enter_live in device mapper,
as there should be no other callers and this allows better documenting
why we do a non-try get.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We must have some way of letting a storage device driver know what
encryption context it should use for en/decrypting a request. However,
it's the upper layers (like the filesystem/fscrypt) that know about and
manages encryption contexts. As such, when the upper layer submits a bio
to the block layer, and this bio eventually reaches a device driver with
support for inline encryption, the device driver will need to have been
told the encryption context for that bio.
We want to communicate the encryption context from the upper layer to the
storage device along with the bio, when the bio is submitted to the block
layer. To do this, we add a struct bio_crypt_ctx to struct bio, which can
represent an encryption context (note that we can't use the bi_private
field in struct bio to do this because that field does not function to pass
information across layers in the storage stack). We also introduce various
functions to manipulate the bio_crypt_ctx and make the bio/request merging
logic aware of the bio_crypt_ctx.
We also make changes to blk-mq to make it handle bios with encryption
contexts. blk-mq can merge many bios into the same request. These bios need
to have contiguous data unit numbers (the necessary changes to blk-merge
are also made to ensure this) - as such, it suffices to keep the data unit
number of just the first bio, since that's all a storage driver needs to
infer the data unit number to use for each data block in each bio in a
request. blk-mq keeps track of the encryption context to be used for all
the bios in a request with the request's rq_crypt_ctx. When the first bio
is added to an empty request, blk-mq will program the encryption context
of that bio into the request_queue's keyslot manager, and store the
returned keyslot in the request's rq_crypt_ctx. All the functions to
operate on encryption contexts are in blk-crypto.c.
Upper layers only need to call bio_crypt_set_ctx with the encryption key,
algorithm and data_unit_num; they don't have to worry about getting a
keyslot for each encryption context, as blk-mq/blk-crypto handles that.
Blk-crypto also makes it possible for request-based layered devices like
dm-rq to make use of inline encryption hardware by cloning the
rq_crypt_ctx and programming a keyslot in the new request_queue when
necessary.
Note that any user of the block layer can submit bios with an
encryption context, such as filesystems, device-mapper targets, etc.
Signed-off-by: Satya Tangirala <satyat@google.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename __bio_add_pc_page() to bio_add_hw_page() and explicitly pass in a
max_sectors argument.
This max_sectors argument can be used to specify constraints from the
hardware.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[ jth: rebased and made public for blk-map.c ]
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
gendisk can't be gone when there is IO activity, so not hold
part0's refcount in IO path.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Cc: Yufen Yu <yuyufen@huawei.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
create_io_context just has a single caller, which also happens to not
even use the return value. Just open code it there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The function has a single caller, so just open code it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move hd_ref_init out of line as there it isn't anywhere near a fast path,
and rename the rcu ref freeing callbacks to be more descriptive.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All callers have the hd_struct at hand, so pass it instead of performing
another lookup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split each sub-command out into a separate helper, and move those helpers
to block/partitions/core.c instead of having a lot of partition
manipulation logic open coded in block/ioctl.c.
Signed-off-by: Christoph Hellwig <hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The bio_map_* helpers are just the low-level helpers for the
blk_rq_map_* APIs. Move them together for better logical grouping,
as no there isn't much overlap with other code in bio.c.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Current make_request based drivers use either blk_alloc_queue_node or
blk_alloc_queue to allocate a queue, and then set up the make_request_fn
function pointer and a few parameters using the blk_queue_make_request
helper. Simplify this by passing the make_request pointer to
blk_alloc_queue, and while at it merge the _node variant into the main
helper by always passing a node_id, and remove the superfluous gfp_mask
parameter. A lower-level __blk_alloc_queue is kept for the blk-mq case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These macros are just used by a few files. Move them out of genhd.h,
which is included everywhere into a new standalone header.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the sysfs _show methods that are used both on the full disk and
partition nodes to genhd.c instead of hiding them in the partitioning
code. Also move the declaration for these methods to block/blk.h so
that we don't expose them to drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove 'q' from arguments since it is not used anymore after
commit 7e992f847a ("block: remove non mq parts from the
flush code").
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Avoid that running test nvme/012 from the blktests suite triggers the
following false positive lockdep complaint:
============================================
WARNING: possible recursive locking detected
5.0.0-rc3-xfstests-00015-g1236f7d60242 #841 Not tainted
--------------------------------------------
ksoftirqd/1/16 is trying to acquire lock:
000000000282032e (&(&fq->mq_flush_lock)->rlock){..-.}, at: flush_end_io+0x4e/0x1d0
but task is already holding lock:
00000000cbadcbc2 (&(&fq->mq_flush_lock)->rlock){..-.}, at: flush_end_io+0x4e/0x1d0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&fq->mq_flush_lock)->rlock);
lock(&(&fq->mq_flush_lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by ksoftirqd/1/16:
#0: 00000000cbadcbc2 (&(&fq->mq_flush_lock)->rlock){..-.}, at: flush_end_io+0x4e/0x1d0
stack backtrace:
CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.0.0-rc3-xfstests-00015-g1236f7d60242 #841
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
dump_stack+0x67/0x90
__lock_acquire.cold.45+0x2b4/0x313
lock_acquire+0x98/0x160
_raw_spin_lock_irqsave+0x3b/0x80
flush_end_io+0x4e/0x1d0
blk_mq_complete_request+0x76/0x110
nvmet_req_complete+0x15/0x110 [nvmet]
nvmet_bio_done+0x27/0x50 [nvmet]
blk_update_request+0xd7/0x2d0
blk_mq_end_request+0x1a/0x100
blk_flush_complete_seq+0xe5/0x350
flush_end_io+0x12f/0x1d0
blk_done_softirq+0x9f/0xd0
__do_softirq+0xca/0x440
run_ksoftirqd+0x24/0x50
smpboot_thread_fn+0x113/0x1e0
kthread+0x121/0x140
ret_from_fork+0x3a/0x50
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
7c20f11680 ("bio-integrity: stop abusing bi_end_io") moves
bio_integrity_free from bio_uninit() to bio_integrity_verify_fn()
and bio_endio(). This way looks wrong because bio may be freed
without calling bio_endio(), for example, blk_rq_unprep_clone() is
called from dm_mq_queue_rq() when the underlying queue of dm-mpath
is busy.
So memory leak of bio integrity data is caused by commit 7c20f11680.
Fixes this issue by re-adding bio_integrity_free() to bio_uninit().
Fixes: 7c20f11680 ("bio-integrity: stop abusing bi_end_io")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by Justin Tee <justin.tee@broadcom.com>
Add commit log, and simplify/fix the original patch wroten by Justin.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Presently, passthrough requests are not accounted for because
blk_do_io_stat() expressly rejects them. Based on some digging
in the history, this doesn't seem like a concious decision but
one that evolved from the change from blk_fs_request() to
blk_rq_is_passthrough().
To support this, call blk_account_io_start() in blk_execute_rq_nowait()
and remove the passthrough check in blk_do_io_stat().
Link: https://lore.kernel.org/linux-block/20191010100526.GA27209@lst.de/
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We got a null pointer deference BUG_ON in blk_mq_rq_timed_out()
as following:
[ 108.825472] BUG: kernel NULL pointer dereference, address: 0000000000000040
[ 108.827059] PGD 0 P4D 0
[ 108.827313] Oops: 0000 [#1] SMP PTI
[ 108.827657] CPU: 6 PID: 198 Comm: kworker/6:1H Not tainted 5.3.0-rc8+ #431
[ 108.829503] Workqueue: kblockd blk_mq_timeout_work
[ 108.829913] RIP: 0010:blk_mq_check_expired+0x258/0x330
[ 108.838191] Call Trace:
[ 108.838406] bt_iter+0x74/0x80
[ 108.838665] blk_mq_queue_tag_busy_iter+0x204/0x450
[ 108.839074] ? __switch_to_asm+0x34/0x70
[ 108.839405] ? blk_mq_stop_hw_queue+0x40/0x40
[ 108.839823] ? blk_mq_stop_hw_queue+0x40/0x40
[ 108.840273] ? syscall_return_via_sysret+0xf/0x7f
[ 108.840732] blk_mq_timeout_work+0x74/0x200
[ 108.841151] process_one_work+0x297/0x680
[ 108.841550] worker_thread+0x29c/0x6f0
[ 108.841926] ? rescuer_thread+0x580/0x580
[ 108.842344] kthread+0x16a/0x1a0
[ 108.842666] ? kthread_flush_work+0x170/0x170
[ 108.843100] ret_from_fork+0x35/0x40
The bug is caused by the race between timeout handle and completion for
flush request.
When timeout handle function blk_mq_rq_timed_out() try to read
'req->q->mq_ops', the 'req' have completed and reinitiated by next
flush request, which would call blk_rq_init() to clear 'req' as 0.
After commit 12f5b93145 ("blk-mq: Remove generation seqeunce"),
normal requests lifetime are protected by refcount. Until 'rq->ref'
drop to zero, the request can really be free. Thus, these requests
cannot been reused before timeout handle finish.
However, flush request has defined .end_io and rq->end_io() is still
called even if 'rq->ref' doesn't drop to zero. After that, the 'flush_rq'
can be reused by the next flush request handle, resulting in null
pointer deference BUG ON.
We fix this problem by covering flush request with 'rq->ref'.
If the refcount is not zero, flush_end_io() return and wait the
last holder recall it. To record the request status, we add a new
entry 'rq_status', which will be used in flush_end_io().
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: stable@vger.kernel.org # v4.18+
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
-------
v2:
- move rq_status from struct request to struct blk_flush_queue
v3:
- remove unnecessary '{}' pair.
v4:
- let spinlock to protect 'fq->rq_status'
v5:
- move rq_status after flush_running_idx member of struct blk_flush_queue
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit c48dac137a ("block: don't hold q->sysfs_lock in elevator_init_mq")
removes q->sysfs_lock from elevator_init_mq(), but forgot to deal with
lockdep_assert_held() called in blk_mq_sched_free_requests() which is
run in failure path of elevator_init_mq().
blk_mq_sched_free_requests() is called in the following 3 functions:
elevator_init_mq()
elevator_exit()
blk_cleanup_queue()
In blk_cleanup_queue(), blk_mq_sched_free_requests() is followed exactly
by 'mutex_lock(&q->sysfs_lock)'.
So moving the lockdep_assert_held() from blk_mq_sched_free_requests()
into elevator_exit() for fixing the report by syzbot.
Reported-by: syzbot+da3b7677bb913dc1b737@syzkaller.appspotmail.com
Fixed: c48dac137a ("block: don't hold q->sysfs_lock in elevator_init_mq")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the default elevator chosen is mq-deadline, elevator_init_mq() may
return an error if mq-deadline initialization fails, leading to
blk_mq_init_allocated_queue() returning an error, which in turn will
cause the block device initialization to fail and the device not being
exposed.
Instead of taking such extreme measure, handle mq-deadline
initialization failures in the same manner as when mq-deadline is not
available (no module to load), that is, default to the "none" scheduler.
With this change, elevator_init_mq() return type can be changed to void.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The kernfs built-in lock of 'kn->count' is held in sysfs .show/.store
path. Meantime, inside block's .show/.store callback, q->sysfs_lock is
required.
However, when mq & iosched kobjects are removed via
blk_mq_unregister_dev() & elv_unregister_queue(), q->sysfs_lock is held
too. This way causes AB-BA lock because the kernfs built-in lock of
'kn-count' is required inside kobject_del() too, see the lockdep warning[1].
On the other hand, it isn't necessary to acquire q->sysfs_lock for
both blk_mq_unregister_dev() & elv_unregister_queue() because
clearing REGISTERED flag prevents storing to 'queue/scheduler'
from being happened. Also sysfs write(store) is exclusive, so no
necessary to hold the lock for elv_unregister_queue() when it is
called in switching elevator path.
So split .sysfs_lock into two: one is still named as .sysfs_lock for
covering sync .store, the other one is named as .sysfs_dir_lock
for covering kobjects and related status change.
sysfs itself can handle the race between add/remove kobjects and
showing/storing attributes under kobjects. For switching scheduler
via storing to 'queue/scheduler', we use the queue flag of
QUEUE_FLAG_REGISTERED with .sysfs_lock for avoiding the race, then
we can avoid to hold .sysfs_lock during removing/adding kobjects.
[1] lockdep warning
======================================================
WARNING: possible circular locking dependency detected
5.3.0-rc3-00044-g73277fc75ea0 #1380 Not tainted
------------------------------------------------------
rmmod/777 is trying to acquire lock:
00000000ac50e981 (kn->count#202){++++}, at: kernfs_remove_by_name_ns+0x59/0x72
but task is already holding lock:
00000000fb16ae21 (&q->sysfs_lock){+.+.}, at: blk_unregister_queue+0x78/0x10b
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&q->sysfs_lock){+.+.}:
__lock_acquire+0x95f/0xa2f
lock_acquire+0x1b4/0x1e8
__mutex_lock+0x14a/0xa9b
blk_mq_hw_sysfs_show+0x63/0xb6
sysfs_kf_seq_show+0x11f/0x196
seq_read+0x2cd/0x5f2
vfs_read+0xc7/0x18c
ksys_read+0xc4/0x13e
do_syscall_64+0xa7/0x295
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #0 (kn->count#202){++++}:
check_prev_add+0x5d2/0xc45
validate_chain+0xed3/0xf94
__lock_acquire+0x95f/0xa2f
lock_acquire+0x1b4/0x1e8
__kernfs_remove+0x237/0x40b
kernfs_remove_by_name_ns+0x59/0x72
remove_files+0x61/0x96
sysfs_remove_group+0x81/0xa4
sysfs_remove_groups+0x3b/0x44
kobject_del+0x44/0x94
blk_mq_unregister_dev+0x83/0xdd
blk_unregister_queue+0xa0/0x10b
del_gendisk+0x259/0x3fa
null_del_dev+0x8b/0x1c3 [null_blk]
null_exit+0x5c/0x95 [null_blk]
__se_sys_delete_module+0x204/0x337
do_syscall_64+0xa7/0x295
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&q->sysfs_lock);
lock(kn->count#202);
lock(&q->sysfs_lock);
lock(kn->count#202);
*** DEADLOCK ***
2 locks held by rmmod/777:
#0: 00000000e69bd9de (&lock){+.+.}, at: null_exit+0x2e/0x95 [null_blk]
#1: 00000000fb16ae21 (&q->sysfs_lock){+.+.}, at: blk_unregister_queue+0x78/0x10b
stack backtrace:
CPU: 0 PID: 777 Comm: rmmod Not tainted 5.3.0-rc3-00044-g73277fc75ea0 #1380
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS ?-20180724_192412-buildhw-07.phx4
Call Trace:
dump_stack+0x9a/0xe6
check_noncircular+0x207/0x251
? print_circular_bug+0x32a/0x32a
? find_usage_backwards+0x84/0xb0
check_prev_add+0x5d2/0xc45
validate_chain+0xed3/0xf94
? check_prev_add+0xc45/0xc45
? mark_lock+0x11b/0x804
? check_usage_forwards+0x1ca/0x1ca
__lock_acquire+0x95f/0xa2f
lock_acquire+0x1b4/0x1e8
? kernfs_remove_by_name_ns+0x59/0x72
__kernfs_remove+0x237/0x40b
? kernfs_remove_by_name_ns+0x59/0x72
? kernfs_next_descendant_post+0x7d/0x7d
? strlen+0x10/0x23
? strcmp+0x22/0x44
kernfs_remove_by_name_ns+0x59/0x72
remove_files+0x61/0x96
sysfs_remove_group+0x81/0xa4
sysfs_remove_groups+0x3b/0x44
kobject_del+0x44/0x94
blk_mq_unregister_dev+0x83/0xdd
blk_unregister_queue+0xa0/0x10b
del_gendisk+0x259/0x3fa
? disk_events_poll_msecs_store+0x12b/0x12b
? check_flags+0x1ea/0x204
? mark_held_locks+0x1f/0x7a
null_del_dev+0x8b/0x1c3 [null_blk]
null_exit+0x5c/0x95 [null_blk]
__se_sys_delete_module+0x204/0x337
? free_module+0x39f/0x39f
? blkcg_maybe_throttle_current+0x8a/0x718
? rwlock_bug+0x62/0x62
? __blkcg_punt_bio_submit+0xd0/0xd0
? trace_hardirqs_on_thunk+0x1a/0x20
? mark_held_locks+0x1f/0x7a
? do_syscall_64+0x4c/0x295
do_syscall_64+0xa7/0x295
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fb696cdbe6b
Code: 73 01 c3 48 8b 0d 1d 20 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 008
RSP: 002b:00007ffec9588788 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 0000559e589137c0 RCX: 00007fb696cdbe6b
RDX: 000000000000000a RSI: 0000000000000800 RDI: 0000559e58913828
RBP: 0000000000000000 R08: 00007ffec9587701 R09: 0000000000000000
R10: 00007fb696d4eae0 R11: 0000000000000206 R12: 00007ffec95889b0
R13: 00007ffec95896b3 R14: 0000559e58913260 R15: 0000559e589137c0
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This function just has a few trivial assignments, has two callers with
one of them being in the fastpath.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Return the segement and let the callers assign them, which makes the code
a littler more obvious. Also pass the request instead of q plus bio
chain, allowing for the use of rq_for_each_bvec.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only need the number of segments in the blk-mq submission path.
Remove the field from struct bio, and return it from a variant of
blk_queue_split instead of that it can passed as an argument to
those functions that need the value.
This also means we stop recounting segments except for cloning
and partial segments.
To keep the number of arguments in this how path down remove
pointless struct request_queue arguments from any of the functions
that had it and grew a nr_segs argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In theory, IO scheduler belongs to request queue, and the request pool
of sched tags belongs to the request queue too.
However, the current tags allocation interfaces are re-used for both
driver tags and sched tags, and driver tags is definitely host wide,
and doesn't belong to any request queue, same with its request pool.
So we need tagset instance for freeing request of sched tags.
Meantime, blk_mq_free_tag_set() often follows blk_cleanup_queue() in case
of non-BLK_MQ_F_TAG_SHARED, this way requires that request pool of sched
tags to be freed before calling blk_mq_free_tag_set().
Commit 47cdee29ef ("block: move blk_exit_queue into __blk_release_queue")
moves blk_exit_queue into __blk_release_queue for simplying the fast
path in generic_make_request(), then causes oops during freeing requests
of sched tags in __blk_release_queue().
Fix the above issue by move freeing request pool of sched tags into
blk_cleanup_queue(), this way is safe becasue queue has been frozen and no any
in-queue requests at that time. Freeing sched tags has to be kept in queue's
release handler becasue there might be un-completed dispatch activity
which might refer to sched tags.
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Fixes: 47cdee29ef ("block: move blk_exit_queue into __blk_release_queue")
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 498f6650ae ("block: Fix a race between the cgroup code and
request queue initialization") moves what blk_exit_queue does into
blk_cleanup_queue() for fixing issue caused by changing back
queue lock.
However, after legacy request IO path is killed, driver queue lock
won't be used at all, and there isn't story for changing back
queue lock. Then the issue addressed by Commit 498f6650ae doesn't
exist any more.
So move move blk_exit_queue into __blk_release_queue.
This patch basically reverts the following two commits:
498f6650ae block: Fix a race between the cgroup code and request queue initialization
24ecc35853 block: Ensure that a request queue is dissociated from the cgroup controller
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
xen_biovec_phys_mergeable() only needs .bv_page of the 2nd bio bvec
for checking if the two bvecs can be merged, so pass page to
xen_biovec_phys_mergeable() directly.
No function change.
Cc: ris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: xen-devel@lists.xenproject.org
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, the queue mapping result is saved in a two-dimensional
array. In the hot path, to get a hctx, we need do following:
q->queue_hw_ctx[q->tag_set->map[type].mq_map[cpu]]
This isn't very efficient. We could save the queue mapping result into
ctx directly with different hctx type, like,
ctx->hctxs[type]
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This isn't exactly the same as the previous count, as it includes
requests for all devices. But that really doesn't matter, if we have
more than the threshold (16) queued up, flush it. It's not worth it
to have an expensive list loop for this.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio->bi_ioc is never set so always NULL. Remove references to it in
bio_disassociate_task() and in rq_ioc() and delete this field from
struct bio. With this change, rq_ioc() always returns
current->io_context without the need for a bio argument. Further
simplify the code and make it more readable by also removing this
helper, which also allows to simplify blk_mq_sched_assign_ioc() by
removing its bio argument.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlvx2sAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGycgIAIuxobwt0RRKa0zO
ROS+34JGoC2yU2P9VdEGWdtxS6ANMVQgKPBhWL6s+xR89Kd+V4xSdJLD1pNTxxqP
0DCva0np1/Q4juH+JbU50v/lykoLgteZ0P0LBRGf1y8p3WiLPv45IbnNsMDNYhB2
7a8rOmZYakRY9CPznRDw3X8cJt3sddKgFJHIOGz1OQJVWtCD0KPGcJmQNsbDSagY
Zx6Z5BKSIdjRqaAdN5gDa1Pft3WQo7TpaQGl80lSsgr5LcjmscXA3sClOCy+25Mo
FZLx0PcwP+Efq8RTGzNK51WSOMa6d37hvjDqUAdQBOR0KbyjRyXQwyQVw/MGbPJs
7J3Pzm0=
=56Mt
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc3' into for-4.21/block
Merge in -rc3 to resolve a few conflicts, but also to get a few
important fixes that have gone into mainline since the block
4.21 branch was forked off (most notably the SCSI queue issue,
which is both a conflict AND needed fix).
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The only remaining user unconditionally drops and reacquires the lock,
which means we really don't need any additional (conditional) annotation.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
->queue_flags is generally not set or cleared in the fast path, and also
generally set or cleared one flag at a time. Make use of the normal
atomic bitops for it so that we don't need to take the queue_lock,
which is otherwise mostly unused in the core block layer now.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No users left since the removal of the legacy request interface, we can
remove all the magic bit stealing now and make it a normal field.
But use WRITE_ONCE/READ_ONCE on the new deadline field, given that we
don't seem to have any mechanism to guarantee a new value actually
gets seen by other threads.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Obviously the created discard bio has to be aligned with logical block size.
This patch introduces the helper of bio_allowed_max_sectors() for
this purpose.
Cc: stable@vger.kernel.org
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Xiao Ni <xni@redhat.com>
Cc: Mariusz Dabrowski <mariusz.dabrowski@intel.com>
Fixes: 744889b7cb ("block: don't deal with discard limit in blkdev_issue_discard()")
Fixes: a22c4d7e34 ("block: re-add discard_granularity and alignment checks")
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prep patch for being able to place request based not just on
CPU location, but also on the type of request.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It's now dead code, nobody uses it.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The only user of legacy timing now is BSG, which is invoked
from the mq timeout handler. Kill the legacy code, and rename
the q->rq_timed_out_fn to q->bsg_job_timeout_fn.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This removes a bunch of core and elevator related code. On the core
front, we remove anything related to queue running, draining,
initialization, plugging, and congestions. We also kill anything
related to request allocation, merging, retrieval, and completion.
Remove any checking for single queue IO schedulers, as they no
longer exist. This means we can also delete a bunch of code related
to request issue, adding, completion, etc - and all the SQ related
ops and helpers.
Also kill the load_default_modules(), as all that did was provide
for a way to load the default single queue elevator.
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With drivers that are settting a virtual boundary constrain, we are
seeing a lot of bio splitting and smaller I/Os being submitted to the
driver.
This happens because the bio gap detection code does not account cases
where PAGE_SIZE - 1 is bigger than queue_virt_boundary() and thus will
split the bio unnecessarily.
Cc: Jan Kara <jack@suse.cz>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Drivers exposing zoned block devices have to initialize and maintain
correctness (i.e. revalidate) of the device zone bitmaps attached to
the device request queue (seq_zones_bitmap and seq_zones_wlock).
To simplify coding this, introduce a generic helper function
blk_revalidate_disk_zones() suitable for most (and likely all) cases.
This new function always update the seq_zones_bitmap and seq_zones_wlock
bitmaps as well as the queue nr_zones field when called for a disk
using a request based queue. For a disk using a BIO based queue, only
the number of zones is updated since these queues do not have
schedulers and so do not need the zone bitmaps.
With this change, the zone bitmap initialization code in sd_zbc.c can be
replaced with a call to this function in sd_zbc_read_zones(), which is
called from the disk revalidate block operation method.
A call to blk_revalidate_disk_zones() is also added to the null_blk
driver for devices created with the zoned mode enabled.
Finally, to ensure that zoned devices created with dm-linear or
dm-flakey expose the correct number of zones through sysfs, a call to
blk_revalidate_disk_zones() is added to dm_table_set_restrictions().
The zone bitmaps allocated and initialized with
blk_revalidate_disk_zones() are freed automatically from
__blk_release_queue() using the block internal function
blk_queue_free_zone_bitmaps().
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is no need to synchronously execute all REQ_OP_ZONE_RESET BIOs
necessary to reset a range of zones. Similarly to what is done for
discard BIOs in blk-lib.c, all zone reset BIOs can be chained and
executed asynchronously and a synchronous call done only for the last
BIO of the chain.
Modify blkdev_reset_zones() to operate similarly to
blkdev_issue_discard() using the next_bio() helper for chaining BIOs. To
avoid code duplication of that function in blk_zoned.c, rename
next_bio() into blk_next_bio() and declare it as a block internal
function in blk.h.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_mq_realloc_hw_ctxs could be invoked during update hw queues.
At the momemt, IO is blocked. Change the gfp flags from GFP_KERNEL
to GFP_NOIO to avoid forever hang during memory allocation in
blk_mq_realloc_hw_ctxs.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Take the Xen check into the core code instead of delegating it to
the architectures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only use it in biovec_phys_mergeable and a m68k paravirt driver,
so just opencode it there. Also remove the pointless unsigned long cast
for the offset in the opencoded instances.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These two checks should always be performed together, so merge them into
a single helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Turn the macro into an inline, move it to blk.h and simplify the
arch hooks a bit.
Also rename the function to biovec_phys_mergeable as there is no need
to shout.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, when update nr_hw_queues, IO scheduler's init_hctx will
be invoked before the mapping between ctx and hctx is adapted
correctly by blk_mq_map_swqueue. The IO scheduler init_hctx (kyber)
may depend on this mapping and get wrong result and panic finally.
A simply way to fix this is that switch the IO scheduler to 'none'
before update the nr_hw_queues, and then switch it back after
update nr_hw_queues. blk_mq_sched_init_/exit_hctx are removed due
to nobody use them any more.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Because blk_do_io_stat() only does a judgement about the request
contributes to IO statistics, it better changes return type to bool.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Alexandru Moise <00moses.alexander00@gmail.com>
Cc: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Current IO controllers for the block layer are less than ideal for our
use case. The io.max controller is great at hard limiting, but it is
not work conserving. This patch introduces io.latency. You provide a
latency target for your group and we monitor the io in short windows to
make sure we are not exceeding those latency targets. This makes use of
the rq-qos infrastructure and works much like the wbt stuff. There are
a few differences from wbt
- It's bio based, so the latency covers the whole block layer in addition to
the actual io.
- We will throttle all IO types that comes in here if we need to.
- We use the mean latency over the 100ms window. This is because writes can
be particularly fast, which could give us a false sense of the impact of
other workloads on our protected workload.
- By default there's no throttling, we set the queue_depth to INT_MAX so that
we can have as many outstanding bio's as we're allowed to. Only at
throttle time do we pay attention to the actual queue depth.
- We backcharge cgroups for root cg issued IO and induce artificial
delays in order to deal with cases like metadata only or swap heavy
workloads.
In testing this has worked out relatively well. Protected workloads
will throttle noisy workloads down to 1 io at time if they are doing
normal IO on their own, or induce up to a 1 second delay per syscall if
they are doing a lot of root issued IO (metadata/swap IO).
Our testing has revolved mostly around our production web servers where
we have hhvm (the web server application) in a protected group and
everything else in another group. We see slightly higher requests per
second (RPS) on the test tier vs the control tier, and much more stable
RPS across all machines in the test tier vs the control tier.
Another test we run is a slow memory allocator in the unprotected group.
Before this would eventually push us into swap and cause the whole box
to die and not recover at all. With these patches we see slight RPS
drops (usually 10-15%) before the memory consumer is properly killed and
things recover within seconds.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is almost no shared logic, which leads to a very confusing code
flow.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These are only used by the block core. Also move the declarations to
block/blk.h.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, struct request has four timestamp fields:
- A start time, set at get_request time, in jiffies, used for iostats
- An I/O start time, set at start_request time, in ktime nanoseconds,
used for blk-stats (i.e., wbt, kyber, hybrid polling)
- Another start time and another I/O start time, used for cfq and bfq
These can all be consolidated into one start time and one I/O start
time, both in ktime nanoseconds, shaving off up to 16 bytes from struct
request depending on the kernel config.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch helps to avoid that new code gets introduced in block drivers
that manipulates queue flags without holding the queue lock when that
lock should be held.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block updates from Jens Axboe:
"This is the main pull request for block IO related changes for the
4.16 kernel. Nothing major in this pull request, but a good amount of
improvements and fixes all over the map. This contains:
- BFQ improvements, fixes, and cleanups from Angelo, Chiara, and
Paolo.
- Support for SMR zones for deadline and mq-deadline from Damien and
Christoph.
- Set of fixes for bcache by way of Michael Lyle, including fixes
from himself, Kent, Rui, Tang, and Coly.
- Series from Matias for lightnvm with fixes from Hans Holmberg,
Javier, and Matias. Mostly centered around pblk, and the removing
rrpc 1.2 in preparation for supporting 2.0.
- A couple of NVMe pull requests from Christoph. Nothing major in
here, just fixes and cleanups, and support for command tracing from
Johannes.
- Support for blk-throttle for tracking reads and writes separately.
From Joseph Qi. A few cleanups/fixes also for blk-throttle from
Weiping.
- Series from Mike Snitzer that enables dm to register its queue more
logically, something that's alwways been problematic on dm since
it's a stacked device.
- Series from Ming cleaning up some of the bio accessor use, in
preparation for supporting multipage bvecs.
- Various fixes from Ming closing up holes around queue mapping and
quiescing.
- BSD partition fix from Richard Narron, fixing a problem where we
can't mount newer (10/11) FreeBSD partitions.
- Series from Tejun reworking blk-mq timeout handling. The previous
scheme relied on atomic bits, but it had races where we would think
a request had timed out if it to reused at the wrong time.
- null_blk now supports faking timeouts, to enable us to better
exercise and test that functionality separately. From me.
- Kill the separate atomic poll bit in the request struct. After
this, we don't use the atomic bits on blk-mq anymore at all. From
me.
- sgl_alloc/free helpers from Bart.
- Heavily contended tag case scalability improvement from me.
- Various little fixes and cleanups from Arnd, Bart, Corentin,
Douglas, Eryu, Goldwyn, and myself"
* 'for-4.16/block' of git://git.kernel.dk/linux-block: (186 commits)
block: remove smart1,2.h
nvme: add tracepoint for nvme_complete_rq
nvme: add tracepoint for nvme_setup_cmd
nvme-pci: introduce RECONNECTING state to mark initializing procedure
nvme-rdma: remove redundant boolean for inline_data
nvme: don't free uuid pointer before printing it
nvme-pci: Suspend queues after deleting them
bsg: use pr_debug instead of hand crafted macros
blk-mq-debugfs: don't allow write on attributes with seq_operations set
nvme-pci: Fix queue double allocations
block: Set BIO_TRACE_COMPLETION on new bio during split
blk-throttle: use queue_is_rq_based
block: Remove kblockd_schedule_delayed_work{,_on}()
blk-mq: Avoid that blk_mq_delay_run_hw_queue() introduces unintended delays
blk-mq: Rename blk_mq_request_direct_issue() into blk_mq_request_issue_directly()
lib/scatterlist: Fix chaining support in sgl_alloc_order()
blk-throttle: track read and write request individually
block: add bdev_read_only() checks to common helpers
block: fail op_is_write() requests to read-only partitions
blk-throttle: export io_serviced_recursive, io_service_bytes_recursive
...
These two functions are only called from inside the block layer so
unexport them.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only have one atomic flag left. Instead of using an entire
unsigned long for that, steal the bottom bit of the deadline
field that we already reserved.
Remove ->atomic_flags, since it's now unused.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We reduce the resolution of request expiry, but since we're already
using jiffies for this where resolution depends on the kernel
configuration and since the timeout resolution is coarse anyway,
that should be fine.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We don't need this to be an atomic flag, it can be a regular
flag. We either end up on the same CPU for the polling, in which
case the state is sane, or we did the sleep which would imply
the needed barrier to ensure we see the right state.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After the recent updates to use generation number and state based
synchronization, we can easily replace REQ_ATOM_STARTED usages by
adding an extra state to distinguish completed but not yet freed
state.
Add MQ_RQ_COMPLETE and replace REQ_ATOM_STARTED usages with
blk_mq_rq_state() tests. REQ_ATOM_STARTED no longer has any users
left and is removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, blk-mq timeout path synchronizes against the usual
issue/completion path using a complex scheme involving atomic
bitflags, REQ_ATOM_*, memory barriers and subtle memory coherence
rules. Unfortunately, it contains quite a few holes.
There's a complex dancing around REQ_ATOM_STARTED and
REQ_ATOM_COMPLETE between issue/completion and timeout paths; however,
they don't have a synchronization point across request recycle
instances and it isn't clear what the barriers add.
blk_mq_check_expired() can easily read STARTED from N-2'th iteration,
deadline from N-1'th, blk_mark_rq_complete() against Nth instance.
In fact, it's pretty easy to make blk_mq_check_expired() terminate a
later instance of a request. If we induce 5 sec delay before
time_after_eq() test in blk_mq_check_expired(), shorten the timeout to
2s, and issue back-to-back large IOs, blk-mq starts timing out
requests spuriously pretty quickly. Nothing actually timed out. It
just made the call on a recycle instance of a request and then
terminated a later instance long after the original instance finished.
The scenario isn't theoretical either.
This patch replaces the broken synchronization mechanism with a RCU
and generation number based one.
1. Each request has a u64 generation + state value, which can be
updated only by the request owner. Whenever a request becomes
in-flight, the generation number gets bumped up too. This provides
the basis for the timeout path to distinguish different recycle
instances of the request.
Also, marking a request in-flight and setting its deadline are
protected with a seqcount so that the timeout path can fetch both
values coherently.
2. The timeout path fetches the generation, state and deadline. If
the verdict is timeout, it records the generation into a dedicated
request abortion field and does RCU wait.
3. The completion path is also protected by RCU (from the previous
patch) and checks whether the current generation number and state
match the abortion field. If so, it skips completion.
4. The timeout path, after RCU wait, scans requests again and
terminates the ones whose generation and state still match the ones
requested for abortion.
By now, the timeout path knows that either the generation number
and state changed if it lost the race or the completion will yield
to it and can safely timeout the request.
While it's more lines of code, it's conceptually simpler, doesn't
depend on direct use of subtle memory ordering or coherence, and
hopefully doesn't terminate the wrong instance.
While this change makes REQ_ATOM_COMPLETE synchronization unnecessary
between issue/complete and timeout paths, REQ_ATOM_COMPLETE isn't
removed yet as it's still used in other places. Future patches will
move all state tracking to the new mechanism and remove all bitops in
the hot paths.
Note that this patch adds a comment explaining a race condition in
BLK_EH_RESET_TIMER path. The race has always been there and this
patch doesn't change it. It's just documenting the existing race.
v2: - Fixed BLK_EH_RESET_TIMER handling as pointed out by Jianchao.
- s/request->gstate_seqc/request->gstate_seq/ as suggested by Peter.
- READ_ONCE() added in blk_mq_rq_update_state() as suggested by Peter.
v3: - Fixed possible extended seqcount / u64_stats_sync read looping
spotted by Peter.
- MQ_RQ_IDLE was incorrectly being set in complete_request instead
of free_request. Fixed.
v4: - Rebased on top of hctx_lock() refactoring patch.
- Added comment explaining the use of hctx_lock() in completion path.
v5: - Added comments requested by Bart.
- Note the addition of BLK_EH_RESET_TIMER race condition in the
commit message.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "jianchao.wang" <jianchao.w.wang@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now we track legacy requests with .q_usage_counter in commit 055f6e18e0
("block: Make q_usage_counter also track legacy requests"), but that
commit never runs and drains legacy queue before waiting for this counter
becoming zero, then IO hang is caused in the test of pulling disk during IO.
This patch fixes the issue by draining requests before waiting for
q_usage_counter becoming zero, both Mauricio and chenxiang reported this
issue, and observed that it can be fixed by this patch.
Link: https://marc.info/?l=linux-block&m=151192424731797&w=2
Fixes: 055f6e18e08f("block: Make q_usage_counter also track legacy requests")
Cc: Wen Xiong <wenxiong@us.ibm.com>
Tested-by: "chenxiang (M)" <chenxiang66@hisilicon.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For memory ordering guarantees on stores, we need to ensure that
these two bits share the same byte of storage in the unsigned
long. Add a comment as to why, and a BUILD_BUG_ON() to ensure that
we don't violate this requirement.
Suggested-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No need to have this helper inline in a header. Also drop the __ prefix.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The only caller of this function is blk_start_request() in the same
file. Fix blk_start_request() description accordingly.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This helper allows looking up a partion under RCU protection without
grabbing a reference to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
And instead call directly into the integrity code from bio_end_io.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some functions in block/blk-core.c must only be used on blk-sq queues
while others are safe to use against any queue type. Document which
functions are intended for blk-sq queues and issue a warning if the
blk-sq API is misused. This does not only help block driver authors
but will also make it easier to remove the blk-sq code once that code
is declared obsolete.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Export this function such that it becomes available to block
drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Matias Bjørling <m@bjorling.me>
Cc: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_insert_flush should be using __blk_end_request to start with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
User configures latency target, but the latency threshold for each
request size isn't fixed. For a SSD, the IO latency highly depends on
request size. To calculate latency threshold, we sample some data, eg,
average latency for request size 4k, 8k, 16k, 32k .. 1M. The latency
threshold of each request size will be the sample latency (I'll call it
base latency) plus latency target. For example, the base latency for
request size 4k is 80us and user configures latency target 60us. The 4k
latency threshold will be 80 + 60 = 140us.
To sample data, we calculate the order base 2 of rounded up IO sectors.
If the IO size is bigger than 1M, it will be accounted as 1M. Since the
calculation does round up, the base latency will be slightly smaller
than actual value. Also if there isn't any IO dispatched for a specific
IO size, we will use the base latency of smaller IO size for this IO
size.
But we shouldn't sample data at any time. The base latency is supposed
to be latency where disk isn't congested, because we use latency
threshold to schedule IOs between cgroups. If disk is congested, the
latency is higher, using it for scheduling is meaningless. Hence we only
do the sampling when block throttling is in the LOW limit, with
assumption disk isn't congested in such state. If the assumption isn't
true, eg, low limit is too high, calculated latency threshold will be
higher.
Hard disk is completely different. Latency depends on spindle seek
instead of request size. Currently this feature is SSD only, we probably
can use a fixed threshold like 4ms for hard disk though.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A cgroup gets assigned a low limit, but the cgroup could never dispatch
enough IO to cross the low limit. In such case, the queue state machine
will remain in LIMIT_LOW state and all other cgroups will be throttled
according to low limit. This is unfair for other cgroups. We should
treat the cgroup idle and upgrade the state machine to lower state.
We also have a downgrade logic. If the state machine upgrades because of
cgroup idle (real idle), the state machine will downgrade soon as the
cgroup is below its low limit. This isn't what we want. A more
complicated case is cgroup isn't idle when queue is in LIMIT_LOW. But
when queue gets upgraded to lower state, other cgroups could dispatch
more IO and this cgroup can't dispatch enough IO, so the cgroup is below
its low limit and looks like idle (fake idle). In this case, the queue
should downgrade soon. The key to determine if we should do downgrade is
to detect if cgroup is truely idle.
Unfortunately it's very hard to determine if a cgroup is real idle. This
patch uses the 'think time check' idea from CFQ for the purpose. Please
note, the idea doesn't work for all workloads. For example, a workload
with io depth 8 has disk utilization 100%, hence think time is 0, eg,
not idle. But the workload can run higher bandwidth with io depth 16.
Compared to io depth 16, the io depth 8 workload is idle. We use the
idea to roughly determine if a cgroup is idle.
We treat a cgroup idle if its think time is above a threshold (by
default 1ms for SSD and 100ms for HD). The idea is think time above the
threshold will start to harm performance. HD is much slower so a longer
think time is ok.
The patch (and the latter patches) uses 'unsigned long' to track time.
We convert 'ns' to 'us' with 'ns >> 10'. This is fast but loses
precision, should not a big deal.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The throtl_slice is 100ms by default. This is a long time for SSD, a lot
of IO can run. To make cgroups have smoother throughput, we choose a
small value (20ms) for SSD.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
throtl_slice is important for blk-throttling. It's called slice
internally but it really is a time window blk-throttling samples data.
blk-throttling will make decision based on the samplings. An example is
bandwidth measurement. A cgroup's bandwidth is measured in the time
interval of throtl_slice.
A small throtl_slice meanse cgroups have smoother throughput but burn
more CPUs. It has 100ms default value, which is not appropriate for all
disks. A fast SSD can dispatch a lot of IOs in 100ms. This patch makes
it tunable.
Since throtl_slice isn't a time slice, the sysfs name
'throttle_sample_time' reflects its character better.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add a new merge strategy that merges discard bios into a request until the
maximum number of discard ranges (or the maximum discard size) is reached
from the plug merging code. I/O scheduler merging is not wired up yet
but might also be useful, although not for fast devices like NVMe which
are the only user for now.
Note that for now we don't support limiting the size of each discard range,
but if needed that can be added later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Switch these constants to an enum, and make let the compiler ensure that
all callers of blk_try_merge and elv_merge handle all potential values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This makes it available outside of blk-merge.c, and inlining such a trivial
helper seems pretty useful to start with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When we attempt to merge request-to-request, we return a 0/1 if we
ended up merging or not. Change that to return the pointer to the
request that we freed. We will use this to move the freeing of
that request out of the merge logic, so that callers can drop
locks before freeing the request.
There should be no functional changes in this patch.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
When I added the blk-mq debugging information to debugfs, I didn't
notice that blktrace also creates a "block" directory in debugfs. Make
them use the same dentry, now created in the core block code. Based on a
patch from Jens.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This can be used to check for fs vs non-fs requests and basically
removes all knowledge of BLOCK_PC specific from the block layer,
as well as preparing for removing the cmd_type field in struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We want to use it outside of blk-core.c.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Prep patch for adding MQ ops as well, since doing anon unions with
named initializers doesn't work on older compilers.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
This patch enables a hybrid polling mode. Instead of polling after IO
submission, we can induce an artificial delay, and then poll after that.
For example, if the IO is presumed to complete in 8 usecs from now, we
can sleep for 4 usecs, wake up, and then do our polling. This still puts
a sleep/wakeup cycle in the IO path, but instead of the wakeup happening
after the IO has completed, it'll happen before. With this hybrid
scheme, we can achieve big latency reductions while still using the same
(or less) amount of CPU.
Signed-off-by: Jens Axboe <axboe@fb.com>
Tested-By: Stephen Bates <sbates@raithlin.com>
Reviewed-By: Stephen Bates <sbates@raithlin.com>
A lot of the REQ_* flags are only used on struct requests, and only of
use to the block layer and a few drivers that dig into struct request
internals.
This patch adds a new req_flags_t rq_flags field to struct request for
them, and thus dramatically shrinks the number of common requests. It
also removes the unfortunate situation where we have to fit the fields
from the same enum into 32 bits for struct bio and 64 bits for
struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
All drivers use the default, so provide an inline version of it. If we
ever need other queue mapping we can add an optional method back,
although supporting will also require major changes to the queue setup
code.
This provides better code generation, and better debugability as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The target SCSI passthrough backend is much better served with the low-level
blk_rq_append_bio construct then the helpers built on top of it, so export it.
Also use the opportunity to remove the pointless request_queue argument and
make the code flow a little more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Timer context is not very useful for drivers to perform any meaningful abort
action from. So instead of calling the driver from this useless context
defer it to a workqueue as soon as possible.
Note that while a delayed_work item would seem the right thing here I didn't
dare to use it due to the magic in blk_add_timer that pokes deep into timer
internals. But maybe this encourages Tejun to add a sensible API for that to
the workqueue API and we'll all be fine in the end :)
Contains a major update from Keith Bush:
"This patch removes synchronizing the timeout work so that the timer can
start a freeze on its own queue. The timer enters the queue, so timer
context can only start a freeze, but not wait for frozen."
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block integrity updates from Jens Axboe:
""This is the joint work of Dan and Martin, cleaning up and improving
the support for block data integrity"
* 'for-4.4/integrity' of git://git.kernel.dk/linux-block:
block, libnvdimm, nvme: provide a built-in blk_integrity nop profile
block: blk_flush_integrity() for bio-based drivers
block: move blk_integrity to request_queue
block: generic request_queue reference counting
nvme: suspend i/o during runtime blk_integrity_unregister
md: suspend i/o during runtime blk_integrity_unregister
md, dm, scsi, nvme, libnvdimm: drop blk_integrity_unregister() at shutdown
block: Inline blk_integrity in struct gendisk
block: Export integrity data interval size in sysfs
block: Reduce the size of struct blk_integrity
block: Consolidate static integrity profile properties
block: Move integrity kobject to struct gendisk
Request queues with merging disabled will not flush the plug list after
BLK_MAX_REQUEST_COUNT requests have been queued, since the code relies
on blk_attempt_plug_merge to compute the request_count. Fix this by
computing the number of queued requests even for nomerge queues.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since they lack requests to pin the request_queue active, synchronous
bio-based drivers may have in-flight integrity work from
bio_integrity_endio() that is not flushed by blk_freeze_queue(). Flush
that work to prevent races to free the queue and the final usage of the
blk_integrity profile.
This is temporary unless/until bio-based drivers start to generically
take a q_usage_counter reference while a bio is in-flight.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
[martin: fix the CONFIG_BLK_DEV_INTEGRITY=n case]
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow pmem, and other synchronous/bio-based block drivers, to fallback
on a per-cpu reference count managed by the core for tracking queue
live/dead state.
The existing per-cpu reference count for the blk_mq case is promoted to
be used in all block i/o scenarios. This involves initializing it by
default, waiting for it to drop to zero at exit, and holding a live
reference over the invocation of q->make_request_fn() in
generic_make_request(). The blk_mq code continues to take its own
reference per blk_mq request and retains the ability to freeze the
queue, but the check that the queue is frozen is moved to
generic_make_request().
This fixes crash signatures like the following:
BUG: unable to handle kernel paging request at ffff880140000000
[..]
Call Trace:
[<ffffffff8145e8bf>] ? copy_user_handle_tail+0x5f/0x70
[<ffffffffa004e1e0>] pmem_do_bvec.isra.11+0x70/0xf0 [nd_pmem]
[<ffffffffa004e331>] pmem_make_request+0xd1/0x200 [nd_pmem]
[<ffffffff811c3162>] ? mempool_alloc+0x72/0x1a0
[<ffffffff8141f8b6>] generic_make_request+0xd6/0x110
[<ffffffff8141f966>] submit_bio+0x76/0x170
[<ffffffff81286dff>] submit_bh_wbc+0x12f/0x160
[<ffffffff81286e62>] submit_bh+0x12/0x20
[<ffffffff813395bd>] jbd2_write_superblock+0x8d/0x170
[<ffffffff8133974d>] jbd2_mark_journal_empty+0x5d/0x90
[<ffffffff813399cb>] jbd2_journal_destroy+0x24b/0x270
[<ffffffff810bc4ca>] ? put_pwq_unlocked+0x2a/0x30
[<ffffffff810bc6f5>] ? destroy_workqueue+0x225/0x250
[<ffffffff81303494>] ext4_put_super+0x64/0x360
[<ffffffff8124ab1a>] generic_shutdown_super+0x6a/0xf0
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull blk-cg updates from Jens Axboe:
"A bit later in the cycle, but this has been in the block tree for a a
while. This is basically four patchsets from Tejun, that improve our
buffered cgroup writeback. It was dependent on the other cgroup
changes, but they went in earlier in this cycle.
Series 1 is set of 5 patches that has cgroup writeback updates:
- bdi_writeback iteration fix which could lead to some wb's being
skipped or repeated during e.g. sync under memory pressure.
- Simplification of wb work wait mechanism.
- Writeback tracepoints updated to report cgroup.
Series 2 is is a set of updates for the CFQ cgroup writeback handling:
cfq has always charged all async IOs to the root cgroup. It didn't
have much choice as writeback didn't know about cgroups and there
was no way to tell who to blame for a given writeback IO.
writeback finally grew support for cgroups and now tags each
writeback IO with the appropriate cgroup to charge it against.
This patchset updates cfq so that it follows the blkcg each bio is
tagged with. Async cfq_queues are now shared across cfq_group,
which is per-cgroup, instead of per-request_queue cfq_data. This
makes all IOs follow the weight based IO resource distribution
implemented by cfq.
- Switched from GFP_ATOMIC to GFP_NOWAIT as suggested by Jeff.
- Other misc review points addressed, acks added and rebased.
Series 3 is the blkcg policy cleanup patches:
This patchset contains assorted cleanups for blkcg_policy methods
and blk[c]g_policy_data handling.
- alloc/free added for blkg_policy_data. exit dropped.
- alloc/free added for blkcg_policy_data.
- blk-throttle's async percpu allocation is replaced with direct
allocation.
- all methods now take blk[c]g_policy_data instead of blkcg_gq or
blkcg.
And finally, series 4 is a set of patches cleaning up the blkcg stats
handling:
blkcg's stats have always been somwhat of a mess. This patchset
tries to improve the situation a bit.
- The following patches added to consolidate blkcg entry point and
blkg creation. This is in itself is an improvement and helps
colllecting common stats on bio issue.
- per-blkg stats now accounted on bio issue rather than request
completion so that bio based and request based drivers can behave
the same way. The issue was spotted by Vivek.
- cfq-iosched implements custom recursive stats and blk-throttle
implements custom per-cpu stats. This patchset make blkcg core
support both by default.
- cfq-iosched and blk-throttle keep track of the same stats
multiple times. Unify them"
* 'for-4.3/blkcg' of git://git.kernel.dk/linux-block: (45 commits)
blkcg: use CGROUP_WEIGHT_* scale for io.weight on the unified hierarchy
blkcg: s/CFQ_WEIGHT_*/CFQ_WEIGHT_LEGACY_*/
blkcg: implement interface for the unified hierarchy
blkcg: misc preparations for unified hierarchy interface
blkcg: separate out tg_conf_updated() from tg_set_conf()
blkcg: move body parsing from blkg_conf_prep() to its callers
blkcg: mark existing cftypes as legacy
blkcg: rename subsystem name from blkio to io
blkcg: refine error codes returned during blkcg configuration
blkcg: remove unnecessary NULL checks from __cfqg_set_weight_device()
blkcg: reduce stack usage of blkg_rwstat_recursive_sum()
blkcg: remove cfqg_stats->sectors
blkcg: move io_service_bytes and io_serviced stats into blkcg_gq
blkcg: make blkg_[rw]stat_recursive_sum() to be able to index into blkcg_gq
blkcg: make blkcg_[rw]stat per-cpu
blkcg: add blkg_[rw]stat->aux_cnt and replace cfq_group->dead_stats with it
blkcg: consolidate blkg creation in blkcg_bio_issue_check()
blk-throttle: improve queue bypass handling
blkcg: move root blkg lookup optimization from throtl_lookup_tg() to __blkg_lookup()
blkcg: inline [__]blkg_lookup()
...
blkg (blkcg_gq) currently is created by blkcg policies invoking
blkg_lookup_create() which ends up repeating about the same code in
different policies. Theoretically, this can avoid the overhead of
looking and/or creating blkg's if blkcg is enabled but no policy is in
use; however, the cost of blkg lookup / creation is very low
especially if only the root blkcg is in use which is highly likely if
no blkcg policy is in active use - it boils down to a single very
predictable conditional and surrounding RCU protection.
This patch consolidates blkg creation to a new function
blkcg_bio_issue_check() which is called during bio issue from
generic_make_request_checks(). blkcg_bio_issue_check() is now the
only function which tries to create missing blkg's. The subsequent
policy and request_list operations just perform blkg_lookup() and if
missing falls back to the root.
* blk_get_rl() no longer tries to create blkg. It uses blkg_lookup()
instead of blkg_lookup_create().
* blk_throtl_bio() is now called from blkcg_bio_issue_check() with rcu
read locked and blkg already looked up. Both throtl_lookup_tg() and
throtl_lookup_create_tg() are dropped.
* cfq is similarly updated. cfq_lookup_create_cfqg() is replaced with
cfq_lookup_cfqg()which uses blkg_lookup().
This consolidates blkg handling and avoids unnecessary blkg creation
retries under memory pressure. In addition, this provides a common
bio entry point into blkcg where things like common accounting can be
performed.
v2: Build fixes for !CONFIG_CFQ_GROUP_IOSCHED and
!CONFIG_BLK_DEV_THROTTLING.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Last patch makes plug work for multiple queue case. However it only
works for single disk case, because it assumes only one request in the
plug list. If a task is accessing multiple disks, eg MD/DM, the
assumption is wrong. Let blk_attempt_plug_merge() record request from
the same queue.
V2: use NULL parameter in !mq case. Fix a bug. Add comments in
blk_attempt_plug_merge to make it less (hopefully) confusion.
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This removes the request types and hacks from the block code and into the
old IDE driver. There is a small amunt of code duplication due to this,
but it's not too bad.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch supports to run one single flush machinery for
each blk-mq dispatch queue, so that:
- current init_request and exit_request callbacks can
cover flush request too, then the buggy copying way of
initializing flush request's pdu can be fixed
- flushing performance gets improved in case of multi hw-queue
In fio sync write test over virtio-blk(4 hw queues, ioengine=sync,
iodepth=64, numjobs=4, bs=4K), it is observed that througput gets
increased a lot over my test environment:
- throughput: +70% in case of virtio-blk over null_blk
- throughput: +30% in case of virtio-blk over SSD image
The multi virtqueue feature isn't merged to QEMU yet, and patches for
the feature can be found in below tree:
git://kernel.ubuntu.com/ming/qemu.git v2.1.0-mq.4
And simply passing 'num_queues=4 vectors=5' should be enough to
enable multi queue(quad queue) feature for QEMU virtio-blk.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch adds 'blk_mq_ctx' parameter to blk_get_flush_queue(),
so that this function can find the corresponding blk_flush_queue
bound with current mq context since the flush queue will become
per hw-queue.
For legacy queue, the parameter can be simply 'NULL'.
For multiqueue case, the parameter should be set as the context
from which the related request is originated. With this context
info, the hw queue and related flush queue can be found easily.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now mission of the two helpers is over, and just call
blk_alloc_flush_queue() and blk_free_flush_queue() directly.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch introduces 'struct blk_flush_queue' and puts all
flush machinery related fields into this structure, so that
- flush implementation details aren't exposed to driver
- it is easy to convert to per dispatch-queue flush machinery
This patch is basically a mechanical replacement.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
These two temporary functions are introduced for holding flush
initialization and de-initialization, so that we can
introduce 'flush queue' easier in the following patch. And
once 'flush queue' and its allocation/free functions are ready,
they will be removed for sake of code readability.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Duplicate the (small) timeout handler in blk-mq so that we can pass
arguments more easily to the driver timeout handler. This enables
the next patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
elv_abort_queue has no callers, and blk_abort_flushes is only called by
elv_abort_queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
For request_fn based devices, the block layer exports a 'nr_requests'
file through sysfs to allow adjusting of queue depth on the fly.
Currently this returns -EINVAL for blk-mq, since it's not wired up.
Wire this up for blk-mq, so that it now also always dynamic
adjustments of the allowed queue depth for any given block device
managed by blk-mq.
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds support for active queue tracking, meaning that the
blk-mq tagging maintains a count of active users of a tag set.
This allows us to maintain a notion of fairness between users,
so that we can distribute the tag depth evenly without starving
some users while allowing others to try unfair deep queues.
If sharing of a tag set is detected, each hardware queue will
track the depth of its own queue. And if this exceeds the total
depth divided by the number of active queues, the user is actively
throttled down.
The active queue count is done lazily to avoid bouncing that data
between submitter and completer. Each hardware queue gets marked
active when it allocates its first tag, and gets marked inactive
when 1) the last tag is cleared, and 2) the queue timeout grace
period has passed.
Signed-off-by: Jens Axboe <axboe@fb.com>
If a requeue event races with a timeout, we can get into the
situation where we attempt to complete a request from the
timeout handler when it's not start anymore. This causes a crash.
So have the timeout handler check that REQ_ATOM_STARTED is still
set on the request - if not, we ignore the event. If this happens,
the request has now been marked as complete. As a consequence, we
need to ensure to clear REQ_ATOM_COMPLETE in blk_mq_start_request(),
as to maintain proper request state.
Signed-off-by: Jens Axboe <axboe@fb.com>
Martin reported that his test system would not boot with
current git, it oopsed with this:
BUG: unable to handle kernel paging request at ffff88046c6c9e80
IP: [<ffffffff812971e0>] blk_queue_start_tag+0x90/0x150
PGD 1ddf067 PUD 1de2067 PMD 47fc7d067 PTE 800000046c6c9060
Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: sd_mod lpfc(+) scsi_transport_fc scsi_tgt oracleasm
rpcsec_gss_krb5 ipv6 igb dca i2c_algo_bit i2c_core hwmon
CPU: 3 PID: 87 Comm: kworker/u17:1 Not tainted 3.14.0+ #246
Hardware name: Supermicro X9DRX+-F/X9DRX+-F, BIOS 3.00 07/09/2013
Workqueue: events_unbound async_run_entry_fn
task: ffff8802743c2150 ti: ffff880273d02000 task.ti: ffff880273d02000
RIP: 0010:[<ffffffff812971e0>] [<ffffffff812971e0>]
blk_queue_start_tag+0x90/0x150
RSP: 0018:ffff880273d03a58 EFLAGS: 00010092
RAX: ffff88046c6c9e78 RBX: ffff880077208e78 RCX: 00000000fffc8da6
RDX: 00000000fffc186d RSI: 0000000000000009 RDI: 00000000fffc8d9d
RBP: ffff880273d03a88 R08: 0000000000000001 R09: ffff8800021c2410
R10: 0000000000000005 R11: 0000000000015b30 R12: ffff88046c5bb8a0
R13: ffff88046c5c0890 R14: 000000000000001e R15: 000000000000001e
FS: 0000000000000000(0000) GS:ffff880277b00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff88046c6c9e80 CR3: 00000000018f6000 CR4: 00000000000407e0
Stack:
ffff880273d03a98 ffff880474b18800 0000000000000000 ffff880474157000
ffff88046c5c0890 ffff880077208e78 ffff880273d03ae8 ffffffff813b9e62
ffff880200000010 ffff880474b18968 ffff880474b18848 ffff88046c5c0cd8
Call Trace:
[<ffffffff813b9e62>] scsi_request_fn+0xf2/0x510
[<ffffffff81293167>] __blk_run_queue+0x37/0x50
[<ffffffff8129ac43>] blk_execute_rq_nowait+0xb3/0x130
[<ffffffff8129ad24>] blk_execute_rq+0x64/0xf0
[<ffffffff8108d2b0>] ? bit_waitqueue+0xd0/0xd0
[<ffffffff813bba35>] scsi_execute+0xe5/0x180
[<ffffffff813bbe4a>] scsi_execute_req_flags+0x9a/0x110
[<ffffffffa01b1304>] sd_spinup_disk+0x94/0x460 [sd_mod]
[<ffffffff81160000>] ? __unmap_hugepage_range+0x200/0x2f0
[<ffffffffa01b2b9a>] sd_revalidate_disk+0xaa/0x3f0 [sd_mod]
[<ffffffffa01b2fb8>] sd_probe_async+0xd8/0x200 [sd_mod]
[<ffffffff8107703f>] async_run_entry_fn+0x3f/0x140
[<ffffffff8106a1c5>] process_one_work+0x175/0x410
[<ffffffff8106b373>] worker_thread+0x123/0x400
[<ffffffff8106b250>] ? manage_workers+0x160/0x160
[<ffffffff8107104e>] kthread+0xce/0xf0
[<ffffffff81070f80>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815f0bac>] ret_from_fork+0x7c/0xb0
[<ffffffff81070f80>] ? kthread_freezable_should_stop+0x70/0x70
Code: 48 0f ab 11 72 db 48 81 4b 40 00 00 10 00 89 83 08 01 00 00 48 89
df 49 8b 04 24 48 89 1c d0 e8 f7 a8 ff ff 49 8b 85 28 05 00 00 <48> 89
58 08 48 89 03 49 8d 85 28 05 00 00 48 89 43 08 49 89 9d
RIP [<ffffffff812971e0>] blk_queue_start_tag+0x90/0x150
RSP <ffff880273d03a58>
CR2: ffff88046c6c9e80
Martin bisected and found this to be the problem patch;
commit 6d113398dc
Author: Jan Kara <jack@suse.cz>
Date: Mon Feb 24 16:39:54 2014 +0100
block: Stop abusing rq->csd.list in blk-softirq
and the problem was immediately apparent. The patch states that
it is safe to reuse queuelist at completion time, since it is
no longer used. However, that is not true if a device is using
block enabled tagging. If that is the case, then the queuelist
is reused to keep track of busy tags. If a device also ended
up using softirq completions, we'd reuse ->queuelist for the
IPI handling while block tagging was still using it. Boom.
Fix this by adding a new ipi_list list head, and share the
memory used with the request hash table. The hash table is
never used after the request is moved to the dispatch list,
which happens long before any potential completion of the
request. Add a new request bit for this, so we don't have
cases that check rq->hash while it could potentially have
been reused for the IPI completion.
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
request_queue bypassing is used to suppress higher-level function of a
request_queue so that they can be switched, reconfigured and shut
down. A request_queue does the followings while bypassing.
* bypasses elevator and io_cq association and queues requests directly
to the FIFO dispatch queue.
* bypasses block cgroup request_list lookup and always uses the root
request_list.
Once confirmed to be bypassing, specific elevator and block cgroup
policy implementations can assume that nothing is in flight for them
and perform various operations which would be dangerous otherwise.
Such confirmation is acheived by short-circuiting all new requests
directly to the dispatch queue and waiting for all the requests which
were issued before to finish. Unfortunately, while the request
allocating and draining sides were properly handled, we forgot to
actually plug the request dispatch path. Even after bypassing mode is
confirmed, if the attached driver tries to fetch a request and the
dispatch queue is empty, __elv_next_request() would invoke the current
elevator's elevator_dispatch_fn() callback. As all in-flight requests
were drained, the elevator wouldn't contain any request but once
bypass is confirmed we don't even know whether the elevator is even
there. It might be in the process of being switched and half torn
down.
Frank Mayhar reports that this actually happened while switching
elevators, leading to an oops.
Let's fix it by making __elv_next_request() avoid invoking the
elevator_dispatch_fn() callback if the queue is bypassing. It already
avoids invoking the callback if the queue is dying. As a dying queue
is guaranteed to be bypassing, we can simply replace blk_queue_dying()
check with blk_queue_bypass().
Reported-by: Frank Mayhar <fmayhar@google.com>
References: http://lkml.kernel.org/g/1390319905.20232.38.camel@bobble.lax.corp.google.com
Cc: stable@vger.kernel.org
Tested-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linux currently has two models for block devices:
- The classic request_fn based approach, where drivers use struct
request units for IO. The block layer provides various helper
functionalities to let drivers share code, things like tag
management, timeout handling, queueing, etc.
- The "stacked" approach, where a driver squeezes in between the
block layer and IO submitter. Since this bypasses the IO stack,
driver generally have to manage everything themselves.
With drivers being written for new high IOPS devices, the classic
request_fn based driver doesn't work well enough. The design dates
back to when both SMP and high IOPS was rare. It has problems with
scaling to bigger machines, and runs into scaling issues even on
smaller machines when you have IOPS in the hundreds of thousands
per device.
The stacked approach is then most often selected as the model
for the driver. But this means that everybody has to re-invent
everything, and along with that we get all the problems again
that the shared approach solved.
This commit introduces blk-mq, block multi queue support. The
design is centered around per-cpu queues for queueing IO, which
then funnel down into x number of hardware submission queues.
We might have a 1:1 mapping between the two, or it might be
an N:M mapping. That all depends on what the hardware supports.
blk-mq provides various helper functions, which include:
- Scalable support for request tagging. Most devices need to
be able to uniquely identify a request both in the driver and
to the hardware. The tagging uses per-cpu caches for freed
tags, to enable cache hot reuse.
- Timeout handling without tracking request on a per-device
basis. Basically the driver should be able to get a notification,
if a request happens to fail.
- Optional support for non 1:1 mappings between issue and
submission queues. blk-mq can redirect IO completions to the
desired location.
- Support for per-request payloads. Drivers almost always need
to associate a request structure with some driver private
command structure. Drivers can tell blk-mq this at init time,
and then any request handed to the driver will have the
required size of memory associated with it.
- Support for merging of IO, and plugging. The stacked model
gets neither of these. Even for high IOPS devices, merging
sequential IO reduces per-command overhead and thus
increases bandwidth.
For now, this is provided as a potential 3rd queueing model, with
the hope being that, as it matures, it can replace both the classic
and stacked model. That would get us back to having just 1 real
model for block devices, leaving the stacked approach to dm/md
devices (as it was originally intended).
Contributions in this patch from the following people:
Shaohua Li <shli@fusionio.com>
Alexander Gordeev <agordeev@redhat.com>
Christoph Hellwig <hch@infradead.org>
Mike Christie <michaelc@cs.wisc.edu>
Matias Bjorling <m@bjorling.me>
Jeff Moyer <jmoyer@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Switch elevator to use the new hashtable implementation. This reduces the
amount of generic unrelated code in the elevator.
This also removes the dymanic allocation of the hash table. The size of the table is
constant so there's no point in paying the price of an extra dereference when accessing
it.
This patch depends on d9b482c ("hashtable: introduce a small and naive
hashtable") which was merged in v3.6.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A block driver may start cleaning up resources needed by its
request_fn as soon as blk_cleanup_queue() finished, so request_fn
must not be invoked after draining finished. This is important
when blk_run_queue() is invoked without any requests in progress.
As an example, if blk_drain_queue() and scsi_run_queue() run in
parallel, blk_drain_queue() may have finished all requests after
scsi_run_queue() has taken a SCSI device off the starved list but
before that last function has had a chance to run the queue.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Chanho Min <chanho.min@lge.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
QUEUE_FLAG_DEAD is used to indicate that queuing new requests must
stop. After this flag has been set queue draining starts. However,
during the queue draining phase it is still safe to invoke the
queue's request_fn, so QUEUE_FLAG_DYING is a better name for this
flag.
This patch has been generated by running the following command
over the kernel source tree:
git grep -lEw 'blk_queue_dead|QUEUE_FLAG_DEAD' |
xargs sed -i.tmp -e 's/blk_queue_dead/blk_queue_dying/g' \
-e 's/QUEUE_FLAG_DEAD/QUEUE_FLAG_DYING/g'; \
sed -i.tmp -e "s/QUEUE_FLAG_DYING$(printf \\t)*5/QUEUE_FLAG_DYING$(printf \\t)5/g" \
include/linux/blkdev.h; \
sed -i.tmp -e 's/ DEAD/ DYING/g' -e 's/dead queue/a dying queue/' \
-e 's/Dead queue/A dying queue/' block/blk-core.c
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove special-casing of non-rw fs style requests (discard). The nomerge
flags are consolidated in blk_types.h, and rq_mergeable() and
bio_mergeable() have been modified to use them.
bio_is_rw() is used in place of bio_has_data() a few places. This is
done to to distinguish true reads and writes from other fs type requests
that carry a payload (e.g. write same).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
__generic_unplug_device() function is removed with commit
7eaceaccab, which forgot to
remove the declaration at meantime. Here remove it.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Request allocation is about to be made per-blkg meaning that there'll
be multiple request lists.
* Make queue full state per request_list. blk_*queue_full() functions
are renamed to blk_*rl_full() and takes @rl instead of @q.
* Rename blk_init_free_list() to blk_init_rl() and make it take @rl
instead of @q. Also add @gfp_mask parameter.
* Add blk_exit_rl() instead of destroying rl directly from
blk_release_queue().
* Add request_list->q and make request alloc/free functions -
blk_free_request(), [__]freed_request(), __get_request() - take @rl
instead of @q.
This patch doesn't introduce any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
cgroup/for-3.5 contains the following changes which blk-cgroup needs
to proceed with the on-going cleanup.
* Dynamic addition and removal of cftypes to make config/stat file
handling modular for policies.
* cgroup removal update to not wait for css references to drain to fix
blkcg removal hang caused by cfq caching cfqgs.
Pull in cgroup/for-3.5 into block/for-3.5/core. This causes the
following conflicts in block/blk-cgroup.c.
* 761b3ef50e "cgroup: remove cgroup_subsys argument from callbacks"
conflicts with blkiocg_pre_destroy() addition and blkiocg_attach()
removal. Resolved by removing @subsys from all subsys methods.
* 676f7c8f84 "cgroup: relocate cftype and cgroup_subsys definitions in
controllers" conflicts with ->pre_destroy() and ->attach() updates
and removal of modular config. Resolved by dropping forward
declarations of the methods and applying updates to the relocated
blkio_subsys.
* 4baf6e3325 "cgroup: convert all non-memcg controllers to the new
cftype interface" builds upon the previous item. Resolved by adding
->base_cftypes to the relocated blkio_subsys.
Signed-off-by: Tejun Heo <tj@kernel.org>
Make the following interface updates to prepare for future ioc related
changes.
* create_io_context() returning ioc only works for %current because it
doesn't increment ref on the ioc. Drop @task parameter from it and
always assume %current.
* Make create_io_context_slowpath() return 0 or -errno and rename it
to create_task_io_context().
* Make ioc_create_icq() take @ioc as parameter instead of assuming
that of %current. The caller, get_request(), is updated to create
ioc explicitly and then pass it into ioc_create_icq().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently block core calls directly into blk-throttle for init, drain
and exit. This patch adds blkcg_{init|drain|exit}_queue() which wraps
the blk-throttle functions. This is to give more control and
visiblity to blkcg core layer for proper layering. Further patches
will add logic common to blkcg policies to the functions.
While at it, collapse blk_throtl_release() into blk_throtl_exit().
There's no reason to keep them separate.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename and extend elv_queisce_start/end() to
blk_queue_bypass_start/end() which are exported and supports nesting
via @q->bypass_depth. Also add blk_queue_bypass() to test bypass
state.
This will be further extended and used for blkio_group management.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_rq_merge_ok() is the elevator-neutral part of merge eligibility
test. blk_try_merge() determines merge direction and expects the
caller to have tested elv_rq_merge_ok() previously.
elv_rq_merge_ok() now wraps blk_rq_merge_ok() and then calls
elv_iosched_allow_merge(). elv_try_merge() is removed and the two
callers are updated to call elv_rq_merge_ok() explicitly followed by
blk_try_merge(). While at it, make rq_merge_ok() functions return
bool.
This is to prepare for plug merge update and doesn't introduce any
behavior change.
This is based on Jens' patch to skip elevator_allow_merge_fn() from
plug merge.
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <4F16F3CA.90904@kernel.dk>
Original-patch-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The block layer has some code trying to determine if two CPUs share a
cache, the scheduler has a similar function. Expose the function used
by the scheduler and make the block layer use it, thereby removing the
block layers usage of CONFIG_SCHED* and topology bits.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Jens Axboe <axboe@kernel.dk>
Link: http://lkml.kernel.org/r/1327579450.2446.95.camel@twins
Now block layer knows everything necessary to create and associate
icq's with requests. Move ioc_create_icq() to blk-ioc.c and update
get_request() such that, if elevator_type->icq_size is set, requests
are automatically associated with their matching icq's before
elv_set_request(). io_context reference is also managed by block core
on request alloc/free.
* Only ioprio/cgroup changed handling remains from cfq_get_cic().
Collapsed into cfq_set_request().
* This removes queue kicking on icq allocation failure (for now). As
icq allocation failure is rare and the only effect of queue kicking
achieved was possibily accelerating queue processing, this change
shouldn't be noticeable.
There is a larger underlying problem. Unlike request allocation,
icq allocation is not guaranteed to succeed eventually after
retries. The number of icq is unbound and thus mempool can't be the
solution either. This effectively adds allocation dependency on
memory free path and thus possibility of deadlock.
This usually wouldn't happen because icq allocation is not a hot
path and, even when the condition triggers, it's highly unlikely
that none of the writeback workers already has icq.
However, this is still possible especially if elevator is being
switched under high memory pressure, so we better get it fixed.
Probably the only solution is just bypassing elevator and appending
to dispatch queue on any elevator allocation failure.
* Comment added to explain how icq's are managed and synchronized.
This completes cleanup of io_context interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With kmem_cache managed by blk-ioc, io_cq exit/release can be moved to
blk-ioc too. The odd ->io_cq->exit/release() callbacks are replaced
with elevator_ops->elevator_exit_icq_fn() with unlinking from both ioc
and q, and freeing automatically handled by blk-ioc. The elevator
operation only need to perform exit operation specific to the elevator
- in cfq's case, exiting the cfqq's.
Also, clearing of io_cq's on q detach is moved to block core and
automatically performed on elevator switch and q release.
Because the q io_cq points to might be freed before RCU callback for
the io_cq runs, blk-ioc code should remember to which cache the io_cq
needs to be freed when the io_cq is released. New field
io_cq->__rcu_icq_cache is added for this purpose. As both the new
field and rcu_head are used only after io_cq is released and the
q/ioc_node fields aren't, they are put into unions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that all io_cq related data structures are in block core layer,
io_cq lookup can be moved from cfq-iosched.c to blk-ioc.c.
Lookup logic from cfq_cic_lookup() is moved to ioc_lookup_icq() with
parameter return type changes (cfqd -> request_queue, cfq_io_cq ->
io_cq) and cfq_cic_lookup() becomes thin wrapper around
cfq_cic_lookup().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
elevator_queue->ops points to the same ops struct ->elevator_type.ops
is pointing to. The only effect of caching it in elevator_queue is
shorter notation - it doesn't save any indirect derefence.
Relocate elevator_type->list which used only during module init/exit
to the end of the structure, rename elevator_queue->elevator_type to
->type, and replace elevator_queue->ops with elevator_queue->type.ops.
This doesn't introduce any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When called under queue_lock, current_io_context() triggers lockdep
warning if it hits allocation path. This is because io_context
installation is protected by task_lock which is not IRQ safe, so it
triggers irq-unsafe-lock -> irq -> irq-safe-lock -> irq-unsafe-lock
deadlock warning.
Given the restriction, accessor + creator rolled into one doesn't work
too well. Drop current_io_context() and let the users access
task->io_context directly inside queue_lock combined with explicit
creation using create_io_context().
Future ioc updates will further consolidate ioc access and the create
interface will be unexported.
While at it, relocate ioc internal interface declarations in blk.h and
add section comments before and after.
This patch does not introduce functional change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* blk_get_queue() is peculiar in that it returns 0 on success and 1 on
failure instead of 0 / -errno or boolean. Update it such that it
returns %true on success and %false on failure.
* Make sure the caller checks for the return value.
* Separate out __blk_get_queue() which doesn't check whether @q is
dead and put it in blk.h. This will be used later.
This patch doesn't introduce any functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ignoring copy_io() during fork, io_context can be allocated from two
places - current_io_context() and set_task_ioprio(). The former is
always called from local task while the latter can be called from
different task. The synchornization between them are peculiar and
dubious.
* current_io_context() doesn't grab task_lock() and assumes that if it
saw %NULL ->io_context, it would stay that way until allocation and
assignment is complete. It has smp_wmb() between alloc/init and
assignment.
* set_task_ioprio() grabs task_lock() for assignment and does
smp_read_barrier_depends() between "ioc = task->io_context" and "if
(ioc)". Unfortunately, this doesn't achieve anything - the latter
is not a dependent load of the former. ie, if ioc itself were being
dereferenced "ioc->xxx", it would mean something (not sure what tho)
but as the code currently stands, the dependent read barrier is
noop.
As only one of the the two test-assignment sequences is task_lock()
protected, the task_lock() can't do much about race between the two.
Nothing prevents current_io_context() and set_task_ioprio() allocating
its own ioc for the same task and overwriting the other's.
Also, set_task_ioprio() can race with exiting task and create a new
ioc after exit_io_context() is finished.
ioc get/put doesn't have any reason to be complex. The only hot path
is accessing the existing ioc of %current, which is simple to achieve
given that ->io_context is never destroyed as long as the task is
alive. All other paths can happily go through task_lock() like all
other task sub structures without impacting anything.
This patch updates ioc get/put so that it becomes more conventional.
* alloc_io_context() is replaced with get_task_io_context(). This is
the only interface which can acquire access to ioc of another task.
On return, the caller has an explicit reference to the object which
should be put using put_io_context() afterwards.
* The functionality of current_io_context() remains the same but when
creating a new ioc, it shares the code path with
get_task_io_context() and always goes through task_lock().
* get_io_context() now means incrementing ref on an ioc which the
caller already has access to (be that an explicit refcnt or implicit
%current one).
* PF_EXITING inhibits creation of new io_context and once
exit_io_context() is finished, it's guaranteed that both ioc
acquisition functions return %NULL.
* All users are updated. Most are trivial but
smp_read_barrier_depends() removal from cfq_get_io_context() needs a
bit of explanation. I suppose the original intention was to ensure
ioc->ioprio is visible when set_task_ioprio() allocates new
io_context and installs it; however, this wouldn't have worked
because set_task_ioprio() doesn't have wmb between init and install.
There are other problems with this which will be fixed in another
patch.
* While at it, use NUMA_NO_NODE instead of -1 for wildcard node
specification.
-v2: Vivek spotted contamination from debug patch. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
cfq allocates per-queue id using ida and uses it to index cic radix
tree from io_context. Move it to q->id and allocate on queue init and
free on queue release. This simplifies cfq a bit and will allow for
further improvements of io context life-cycle management.
This patch doesn't introduce any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are a number of QUEUE_FLAG_DEAD tests. Add blk_queue_dead()
macro and use it.
This patch doesn't introduce any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
request_queue is refcounted but actually depdends on lifetime
management from the queue owner - on blk_cleanup_queue(), block layer
expects that there's no request passing through request_queue and no
new one will.
This is fundamentally broken. The queue owner (e.g. SCSI layer)
doesn't have a way to know whether there are other active users before
calling blk_cleanup_queue() and other users (e.g. bsg) don't have any
guarantee that the queue is and would stay valid while it's holding a
reference.
With delay added in blk_queue_bio() before queue_lock is grabbed, the
following oops can be easily triggered when a device is removed with
in-flight IOs.
sd 0:0:1:0: [sdb] Stopping disk
ata1.01: disabled
general protection fault: 0000 [#1] PREEMPT SMP
CPU 2
Modules linked in:
Pid: 648, comm: test_rawio Not tainted 3.1.0-rc3-work+ #56 Bochs Bochs
RIP: 0010:[<ffffffff8137d651>] [<ffffffff8137d651>] elv_rqhash_find+0x61/0x100
...
Process test_rawio (pid: 648, threadinfo ffff880019efa000, task ffff880019ef8a80)
...
Call Trace:
[<ffffffff8137d774>] elv_merge+0x84/0xe0
[<ffffffff81385b54>] blk_queue_bio+0xf4/0x400
[<ffffffff813838ea>] generic_make_request+0xca/0x100
[<ffffffff81383994>] submit_bio+0x74/0x100
[<ffffffff811c53ec>] dio_bio_submit+0xbc/0xc0
[<ffffffff811c610e>] __blockdev_direct_IO+0x92e/0xb40
[<ffffffff811c39f7>] blkdev_direct_IO+0x57/0x60
[<ffffffff8113b1c5>] generic_file_aio_read+0x6d5/0x760
[<ffffffff8118c1ca>] do_sync_read+0xda/0x120
[<ffffffff8118ce55>] vfs_read+0xc5/0x180
[<ffffffff8118cfaa>] sys_pread64+0x9a/0xb0
[<ffffffff81afaf6b>] system_call_fastpath+0x16/0x1b
This happens because blk_queue_cleanup() destroys the queue and
elevator whether IOs are in progress or not and DEAD tests are
sprinkled in the request processing path without proper
synchronization.
Similar problem exists for blk-throtl. On queue cleanup, blk-throtl
is shutdown whether it has requests in it or not. Depending on
timing, it either oopses or throttled bios are lost putting tasks
which are waiting for bio completion into eternal D state.
The way it should work is having the usual clear distinction between
shutdown and release. Shutdown drains all currently pending requests,
marks the queue dead, and performs partial teardown of the now
unnecessary part of the queue. Even after shutdown is complete,
reference holders are still allowed to issue requests to the queue
although they will be immmediately failed. The rest of teardown
happens on release.
This patch makes the following changes to make blk_queue_cleanup()
behave as proper shutdown.
* QUEUE_FLAG_DEAD is now set while holding both q->exit_mutex and
queue_lock.
* Unsynchronized DEAD check in generic_make_request_checks() removed.
This couldn't make any meaningful difference as the queue could die
after the check.
* blk_drain_queue() updated such that it can drain all requests and is
now called during cleanup.
* blk_throtl updated such that it checks DEAD on grabbing queue_lock,
drains all throttled bios during cleanup and free td when queue is
released.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_throtl_bio() and throtl_get_tg() have rather unusual interface.
* throtl_get_tg() returns pointer to a valid tg or ERR_PTR(-ENODEV),
and drops queue_lock in the latter case. Different locking context
depending on return value is error-prone and DEAD state is scheduled
to be protected by queue_lock anyway. Move DEAD check inside
queue_lock and return valid tg or NULL.
* blk_throtl_bio() indicates return status both with its return value
and in/out param **@bio. The former is used to indicate whether
queue is found to be dead during throtl processing. The latter
whether the bio is throttled.
There's no point in returning DEAD check result from
blk_throtl_bio(). The queue can die after blk_throtl_bio() is
finished but before make_request_fn() grabs queue lock.
Make it take *@bio instead and return boolean result indicating
whether the request is throttled or not.
This patch doesn't cause any visible functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reorganize queue draining related code in preparation of queue exit
changes.
* Factor out actual draining from elv_quiesce_start() to
blk_drain_queue().
* Make elv_quiesce_start/end() responsible for their own locking.
* Replace open-coded ELVSWITCH clearing in elevator_switch() with
elv_quiesce_end().
This patch doesn't cause any visible functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_throtl interface is block internal and there's no reason to have
them in linux/blkdev.h. Move them to block/blk.h.
This patch doesn't introduce any functional change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit ae1b153962, block: reimplement
FLUSH/FUA to support merge, introduced a performance regression when
running any sort of fsyncing workload using dm-multipath and certain
storage (in our case, an HP EVA). The test I ran was fs_mark, and it
dropped from ~800 files/sec on ext4 to ~100 files/sec. It turns out
that dm-multipath always advertised flush+fua support, and passed
commands on down the stack, where those flags used to get stripped off.
The above commit changed that behavior:
static inline struct request *__elv_next_request(struct request_queue *q)
{
struct request *rq;
while (1) {
- while (!list_empty(&q->queue_head)) {
+ if (!list_empty(&q->queue_head)) {
rq = list_entry_rq(q->queue_head.next);
- if (!(rq->cmd_flags & (REQ_FLUSH | REQ_FUA)) ||
- (rq->cmd_flags & REQ_FLUSH_SEQ))
- return rq;
- rq = blk_do_flush(q, rq);
- if (rq)
- return rq;
+ return rq;
}
Note that previously, a command would come in here, have
REQ_FLUSH|REQ_FUA set, and then get handed off to blk_do_flush:
struct request *blk_do_flush(struct request_queue *q, struct request *rq)
{
unsigned int fflags = q->flush_flags; /* may change, cache it */
bool has_flush = fflags & REQ_FLUSH, has_fua = fflags & REQ_FUA;
bool do_preflush = has_flush && (rq->cmd_flags & REQ_FLUSH);
bool do_postflush = has_flush && !has_fua && (rq->cmd_flags &
REQ_FUA);
unsigned skip = 0;
...
if (blk_rq_sectors(rq) && !do_preflush && !do_postflush) {
rq->cmd_flags &= ~REQ_FLUSH;
if (!has_fua)
rq->cmd_flags &= ~REQ_FUA;
return rq;
}
So, the flush machinery was bypassed in such cases (q->flush_flags == 0
&& rq->cmd_flags & (REQ_FLUSH|REQ_FUA)).
Now, however, we don't get into the flush machinery at all. Instead,
__elv_next_request just hands a request with flush and fua bits set to
the scsi_request_fn, even if the underlying request_queue does not
support flush or fua.
The agreed upon approach is to fix the flush machinery to allow
stacking. While this isn't used in practice (since there is only one
request-based dm target, and that target will now reflect the flush
flags of the underlying device), it does future-proof the solution, and
make it function as designed.
In order to make this work, I had to add a field to the struct request,
inside the flush structure (to store the original req->end_io). Shaohua
had suggested overloading the union with rb_node and completion_data,
but the completion data is used by device mapper and can also be used by
other drivers. So, I didn't see a way around the additional field.
I tested this patch on an HP EVA with both ext4 and xfs, and it recovers
the lost performance. Comments and other testers, as always, are
appreciated.
Cheers,
Jeff
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Since for-2.6.40/core was forked off the 2.6.39 devel tree, we've
had churn in the core area that makes it difficult to handle
patches for eg cfq or blk-throttle. Instead of requiring that they
be based in older versions with bugs that have been fixed later
in the rc cycle, merge in 2.6.39 final.
Also fixes up conflicts in the below files.
Conflicts:
drivers/block/paride/pcd.c
drivers/cdrom/viocd.c
drivers/ide/ide-cd.c
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
blk_cleanup_queue() calls elevator_exit() and after this, we can't
touch the elevator without oopsing. __elv_next_request() must check
for this state because in the refcounted queue model, we can still
call it after blk_cleanup_queue() has been called.
This was reported as causing an oops attributable to scsi.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In some drives, flush requests are non-queueable. When flush request is
running, normal read/write requests can't run. If block layer dispatches
such request, driver can't handle it and requeue it. Tejun suggested we
can hold the queue when flush is running. This can avoid unnecessary
requeue. Also this can improve performance. For example, we have
request flush1, write1, flush 2. flush1 is dispatched, then queue is
hold, write1 isn't inserted to queue. After flush1 is finished, flush2
will be dispatched. Since disk cache is already clean, flush2 will be
finished very soon, so looks like flush2 is folded to flush1.
In my test, the queue holding completely solves a regression introduced by
commit 53d63e6b0d:
block: make the flush insertion use the tail of the dispatch list
It's not a preempt type request, in fact we have to insert it
behind requests that do specify INSERT_FRONT.
which causes about 20% regression running a sysbench fileio
workload.
Stable: 2.6.39 only
Cc: stable@kernel.org
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We are currently using this flag to check whether it's safe
to call into ->request_fn(). If it is set, we punt to kblockd.
But we get a lot of false positives and excessive punts to
kblockd, which hurts performance.
The only real abuser of this infrastructure is SCSI. So export
the async queue run and convert SCSI over to use that. There's
room for improvement in that SCSI need not always use the async
call, but this fixes our performance issue and they can fix that
up in due time.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly. I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
One of the disadvantages of on-stack plugging is that we potentially
lose out on merging since all pending IO isn't always visible to
everybody. When we flush the on-stack plugs, right now we don't do
any checks to see if potential merge candidates could be utilized.
Correct this by adding a new insert variant, ELEVATOR_INSERT_SORT_MERGE.
It works just ELEVATOR_INSERT_SORT, but first checks whether we can
merge with an existing request before doing the insertion (if we fail
merging).
This fixes a regression with multiple processes issuing IO that
can be merged.
Thanks to Shaohua Li <shaohua.li@intel.com> for testing and fixing
an accounting bug.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The current FLUSH/FUA support has evolved from the implementation
which had to perform queue draining. As such, sequencing is done
queue-wide one flush request after another. However, with the
draining requirement gone, there's no reason to keep the queue-wide
sequential approach.
This patch reimplements FLUSH/FUA support such that each FLUSH/FUA
request is sequenced individually. The actual FLUSH execution is
double buffered and whenever a request wants to execute one for either
PRE or POSTFLUSH, it queues on the pending queue. Once certain
conditions are met, a flush request is issued and on its completion
all pending requests proceed to the next sequence.
This allows arbitrary merging of different type of flushes. How they
are merged can be primarily controlled and tuned by adjusting the
above said 'conditions' used to determine when to issue the next
flush.
This is inspired by Darrick's patches to merge multiple zero-data
flushes which helps workloads with highly concurrent fsync requests.
* As flush requests are never put on the IO scheduler, request fields
used for flush share space with rq->rb_node. rq->completion_data is
moved out of the union. This increases the request size by one
pointer.
As rq->elevator_private* are used only by the iosched too, it is
possible to reduce the request size further. However, to do that,
we need to modify request allocation path such that iosched data is
not allocated for flush requests.
* FLUSH/FUA processing happens on insertion now instead of dispatch.
- Comments updated as per Vivek and Mike.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
rq == &q->flush_rq was used to determine whether a rq is part of a
flush sequence, which worked because all requests in a flush sequence
were sequenced using the single dedicated request. This is about to
change, so introduce REQ_FLUSH_SEQ flag to distinguish flush sequence
requests.
This patch doesn't cause any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This reverts commit 7681bfeecc.
Conflicts:
include/linux/genhd.h
It has numerous issues with the cleanup path and non-elevator
devices. Revert it for now so we can come up with a clean
version without rushing things.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-2.6.37/barrier' of git://git.kernel.dk/linux-2.6-block: (46 commits)
xen-blkfront: disable barrier/flush write support
Added blk-lib.c and blk-barrier.c was renamed to blk-flush.c
block: remove BLKDEV_IFL_WAIT
aic7xxx_old: removed unused 'req' variable
block: remove the BH_Eopnotsupp flag
block: remove the BLKDEV_IFL_BARRIER flag
block: remove the WRITE_BARRIER flag
swap: do not send discards as barriers
fat: do not send discards as barriers
ext4: do not send discards as barriers
jbd2: replace barriers with explicit flush / FUA usage
jbd2: Modify ASYNC_COMMIT code to not rely on queue draining on barrier
jbd: replace barriers with explicit flush / FUA usage
nilfs2: replace barriers with explicit flush / FUA usage
reiserfs: replace barriers with explicit flush / FUA usage
gfs2: replace barriers with explicit flush / FUA usage
btrfs: replace barriers with explicit flush / FUA usage
xfs: replace barriers with explicit flush / FUA usage
block: pass gfp_mask and flags to sb_issue_discard
dm: convey that all flushes are processed as empty
...
* 'for-2.6.37/core' of git://git.kernel.dk/linux-2.6-block: (39 commits)
cfq-iosched: Fix a gcc 4.5 warning and put some comments
block: Turn bvec_k{un,}map_irq() into static inline functions
block: fix accounting bug on cross partition merges
block: Make the integrity mapped property a bio flag
block: Fix double free in blk_integrity_unregister
block: Ensure physical block size is unsigned int
blkio-throttle: Fix possible multiplication overflow in iops calculations
blkio-throttle: limit max iops value to UINT_MAX
blkio-throttle: There is no need to convert jiffies to milli seconds
blkio-throttle: Fix link failure failure on i386
blkio: Recalculate the throttled bio dispatch time upon throttle limit change
blkio: Add root group to td->tg_list
blkio: deletion of a cgroup was causes oops
blkio: Do not export throttle files if CONFIG_BLK_DEV_THROTTLING=n
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: revert bad fix for memory hotplug causing bounces
Fix compile error in blk-exec.c for !CONFIG_DETECT_HUNG_TASK
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: Prevent hang_check firing during long I/O
cfq: improve fsync performance for small files
...
Fix up trivial conflicts due to __rcu sparse annotation in include/linux/genhd.h
/proc/diskstats would display a strange output as follows.
$ cat /proc/diskstats |grep sda
8 0 sda 90524 7579 102154 20464 0 0 0 0 0 14096 20089
8 1 sda1 19085 1352 21841 4209 0 0 0 0 4294967064 15689 4293424691
~~~~~~~~~~
8 2 sda2 71252 3624 74891 15950 0 0 0 0 232 23995 1562390
8 3 sda3 54 487 2188 92 0 0 0 0 0 88 92
8 4 sda4 4 0 8 0 0 0 0 0 0 0 0
8 5 sda5 81 2027 2130 138 0 0 0 0 0 87 137
Its reason is the wrong way of accounting hd_struct->in_flight. When a bio is
merged into a request belongs to different partition by ELEVATOR_FRONT_MERGE.
The detailed root cause is as follows.
Assuming that there are two partition, sda1 and sda2.
1. A request for sda2 is in request_queue. Hence sda1's hd_struct->in_flight
is 0 and sda2's one is 1.
| hd_struct->in_flight
---------------------------
sda1 | 0
sda2 | 1
---------------------------
2. A bio belongs to sda1 is issued and is merged into the request mentioned on
step1 by ELEVATOR_BACK_MERGE. The first sector of the request is changed
from sda2 region to sda1 region. However the two partition's
hd_struct->in_flight are not changed.
| hd_struct->in_flight
---------------------------
sda1 | 0
sda2 | 1
---------------------------
3. The request is finished and blk_account_io_done() is called. In this case,
sda2's hd_struct->in_flight, not a sda1's one, is decremented.
| hd_struct->in_flight
---------------------------
sda1 | -1
sda2 | 1
---------------------------
The patch fixes the problem by caching the partition lookup
inside the request structure, hence making sure that the increment
and decrement will always happen on the same partition struct. This
also speeds up IO with accounting enabled, since it cuts down on
the number of lookups we have to do.
When reloading partition tables, quiesce IO to ensure that no
request references to the partition struct exists. When it is safe
to free the partition table, the IO for that device is restarted
again.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Some controllers have a hardware limit on the number of protection
information scatter-gather list segments they can handle.
Introduce a max_integrity_segments limit in the block layer and provide
a new scsi_host_template setting that allows HBA drivers to provide a
value suitable for the hardware.
Add support for honoring the integrity segment limit when merging both
bios and requests.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
Now that the backend conversion is complete, export sequenced
FLUSH/FUA capability through REQ_FLUSH/FUA flags. REQ_FLUSH means the
device cache should be flushed before executing the request. REQ_FUA
means that the data in the request should be on non-volatile media on
completion.
Block layer will choose the correct way of implementing the semantics
and execute it. The request may be passed to the device directly if
the device can handle it; otherwise, it will be sequenced using one or
more proxy requests. Devices will never see REQ_FLUSH and/or FUA
which it doesn't support.
Also, unlike the original REQ_HARDBARRIER, REQ_FLUSH/FUA requests are
never failed with -EOPNOTSUPP. If the underlying device doesn't
support FLUSH/FUA, the block layer simply make those noop. IOW, it no
longer distinguishes between writeback cache which doesn't support
cache flush and writethrough/no cache. Devices which have WB cache
w/o flush are very difficult to come by these days and there's nothing
much we can do anyway, so it doesn't make sense to require everyone to
implement -EOPNOTSUPP handling. This will simplify filesystems and
block drivers as they can drop -EOPNOTSUPP retry logic for barriers.
* QUEUE_ORDERED_* are removed and QUEUE_FSEQ_* are moved into
blk-flush.c.
* REQ_FLUSH w/o data can also be directly passed to drivers without
sequencing but some drivers assume that zero length requests don't
have rq->bio which isn't true for these requests requiring the use
of proxy requests.
* REQ_COMMON_MASK now includes REQ_FLUSH | REQ_FUA so that they are
copied from bio to request.
* WRITE_BARRIER is marked deprecated and WRITE_FLUSH, WRITE_FUA and
WRITE_FLUSH_FUA are added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
With ordering requirements dropped, barrier and ordered are misnomers.
Now all block layer does is sequencing FLUSH and FUA. Rename them to
flush.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Filesystems will take all the responsibilities for ordering requests
around commit writes and will only indicate how the commit writes
themselves should be handled by block layers. This patch drops
barrier ordering by queue draining from block layer. Ordering by
draining implementation was somewhat invasive to request handling.
List of notable changes follow.
* Each queue has 1 bit color which is flipped on each barrier issue.
This is used to track whether a given request is issued before the
current barrier or not. REQ_ORDERED_COLOR flag and coloring
implementation in __elv_add_request() are removed.
* Requests which shouldn't be processed yet for draining were stalled
by returning -EAGAIN from blk_do_ordered() according to the test
result between blk_ordered_req_seq() and blk_blk_ordered_cur_seq().
This logic is removed.
* Draining completion logic in elv_completed_request() removed.
* All barrier sequence requests were queued to request queue and then
trckled to lower layer according to progress and thus maintaining
request orders during requeue was necessary. This is replaced by
queueing the next request in the barrier sequence only after the
current one is complete from blk_ordered_complete_seq(), which
removes the need for multiple proxy requests in struct request_queue
and the request sorting logic in the ELEVATOR_INSERT_REQUEUE path of
elv_insert().
* As barriers no longer have ordering constraints, there's no need to
dump the whole elevator onto the dispatch queue on each barrier.
Insert barriers at the front instead.
* If other barrier requests come to the front of the dispatch queue
while one is already in progress, they are stored in
q->pending_barriers and restored to dispatch queue one-by-one after
each barrier completion from blk_ordered_complete_seq().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Make the following cleanups in preparation of barrier/flush update.
* blk_do_ordered() declaration is moved from include/linux/blkdev.h to
block/blk.h.
* blk_do_ordered() now returns pointer to struct request, with %NULL
meaning "try the next request" and ERR_PTR(-EAGAIN) "try again
later". The third case will be dropped with further changes.
* In the initialization of proxy barrier request, data direction is
already set by init_request_from_bio(). Drop unnecessary explicit
REQ_WRITE setting and move init_request_from_bio() above REQ_FUA
flag setting.
* add_request() is collapsed into __make_request().
These changes don't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
While testing CPU DLPAR, the following problem was discovered.
We were DLPAR removing the first CPU, which in this case was
logical CPUs 0-3. CPUs 0-2 were already marked offline and
we were in the process of offlining CPU 3. After marking
the CPU inactive and offline in cpu_disable, but before the
cpu was completely idle (cpu_die), we ended up in __make_request
on CPU 3. There we looked at the topology map to see which CPU
to complete the I/O on and found no CPUs in the cpu_sibling_map.
This resulted in the block layer setting the completion cpu
to be NR_CPUS, which then caused an oops when we tried to
complete the I/O.
Fix this by sanity checking the value we return from blk_cpu_to_group
to be a valid cpu value.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests. This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Failfast has characteristics from other attributes. When issuing,
executing and successuflly completing requests, failfast doesn't make
any difference. It only affects how a request is handled on failure.
Allowing requests with different failfast settings to be merged cause
normal IOs to fail prematurely while not allowing has performance
penalties as failfast is used for read aheads which are likely to be
located near in-flight or to-be-issued normal IOs.
This patch introduces the concept of 'mixed merge'. A request is a
mixed merge if it is merge of segments which require different
handling on failure. Currently the only mixable attributes are
failfast ones (or lack thereof).
When a bio with different failfast settings is added to an existing
request or requests of different failfast settings are merged, the
merged request is marked mixed. Each bio carries failfast settings
and the request always tracks failfast state of the first bio. When
the request fails, blk_rq_err_bytes() can be used to determine how
many bytes can be safely failed without crossing into an area which
requires further retrials.
This allows request merging regardless of failfast settings while
keeping the failure handling correct.
This patch only implements mixed merge but doesn't enable it. The
next one will update SCSI to make use of mixed merge.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Niel Lambrechts <niel.lambrechts@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The commit below in 2.6-block/for-2.6.31 causes no diskstat problem
because the blk_discard_rq() check was added with '&&'.
It should be 'blk_fs_request() || blk_discard_rq()'.
This patch does it and fixes the no diskstat problem.
Please review and apply.
------ /proc/diskstat without this patch -------------------------------------
8 0 sda 0 0 0 0 0 0 0 0 0 0 0
------------------------------------------------------------------------------
----- /proc/diskstat with this patch applied ---------------------------------
8 0 sda 4186 303 373621 61600 9578 3859 107468 169479 2 89755 231059
------------------------------------------------------------------------------
--------------------------------------------------------------------------
commit c69d48540c
Author: Jens Axboe <jens.axboe@oracle.com>
Date: Fri Apr 24 08:12:19 2009 +0200
block: include discard requests in IO accounting
We currently don't do merging on discard requests, but we potentially
could. If we do, then we need to include discard requests in the IO
accounting, or merging would end up decrementing in_flight IO counters
for an IO which never incremented them.
So enable accounting for discard requests.
<snip>
static inline int blk_do_io_stat(struct request *rq)
{
- return rq->rq_disk && blk_rq_io_stat(rq) && blk_fs_request(rq);
+ return rq->rq_disk && blk_rq_io_stat(rq) && blk_fs_request(rq) &&
+ blk_discard_rq(rq);
}
--------------------------------------------------------------------------
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
