Export DSR register through sysfs same as we did for the CID, CSD and
OCR registers.
Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Registers CID and CSD are already exported through sysfs so let's make
this interface complete by adding missing OCR register.
Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When initializing sd or sdio card, we get struct mmc_card
from mmc_alloc_card which allocates it by kzalloc. So we don't
need another memset while decoding cid.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While in sdhci_execute_tuning() the choice whether or not to enable the
tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the
check is done on the capability of the card.
This difference is causing some issues with some SDIO cards in DDR50
mode where the CDM19 is wrongly issued.
With this patch we modify the check in both
mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision
only according to the actual timing specification.
Cc: stable@vger.kernel.org
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD card specification allows cards to error out a SWITCH command
where the requested function in a group is not supported. The spec
provides for a set of capabilities which indicate which functions are
supported.
In the case of the power limit, requesting an unsupported power level
via the SWITCH command fails, resulting in the power level remaining at
the power-on default of 0.72W, even though the host and card may support
higher powers levels.
This has been seen with SanDisk 8GB cards, which support the default
0.72W and 1.44W (200mA and 400mA) in combination with an iMX6 host,
supporting up to 2.88W (800mA). This currently causes us to try to set
a power limit function value of '3' (2.88W) which the card errors out
on, and thereby causes the power level to remain at 0.72W rather than
the desired 1.44W.
Arrange to limit the selected current limit by the capabilities reported
by the card to avoid the SWITCH command failing. Select the highest
current limit that the host and card combination support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes: a39ca6ae0a ("mmc: core: Simplify and fix for SD switch processing")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A card can be removed while it is runtime suspended.
Do not print an error message.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CAP_RUNTIME_RESUME was invented to decrease system PM resume time for
systems that particularly needs this. As the feature has matured let's
make it the default behavior for MMC/SD.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There's little sense in releasing the host on mmc_add_card() error
immediately after reclaiming it, so reclaim the host only in case
of success.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.
Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.
To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
As SD Specifications Part1 Physical Layer Specification Version
3.01 says, CMD19 tuning is available for unlocked cards in transfer
state of 1.8V signaling mode. The small difference between v3.00
and 3.01 spec means that CMD19 tuning is also available for DDR50
mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the ->reset() callback is implemented for SD, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding drive strength support
for eMMC, add drive_strength to struct mmc_card
to record the card drive strength for UHS-I modes
and HS200 / HS400. For eMMC this will be needed
when switching between HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make a new function out of common code used for drive
strength selection.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporting also eMMC drive strength,
add the 'card' as a parameter so that the callback can
distinguish different types of cards if necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Card drive strength selection uses a callback to
which a mask of supported drive strengths is passed.
Currently, the bits are checked against the values
in the SD specifications. That is not necessary
because the callback will anyway match the mask
against a valid value. Simplify by taking the mask
as is but still ensuring that the default mandatory
value (type B) is always supported.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initialization of UHS-I modes for SD and SDIO cards
employs a callback to allow the host driver to
choose a drive strength value. Currently that
assumes the card drive strength and host driver
type must be the same value. Change to let the
callback make that decision and return both the
card drive strength and host driver type.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not uncommon to see systems where there is no physical write-protect
signal (e.g. when using eMMC or microSD card slots). For some controllers,
which have a dedicated write-protection detection logic (like SDHCI
controllers), the get_ro() callback can return bogus data in such a case.
Instead of handling this on a per controller basis this patch adds a new
capability flag to the MMC core that can be set to specify that the result
of get_ro() is invalid. When the flag is set the core will not call
get_ro() and assume that the card is always read-write.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
For each MMC, SD and SDIO there is code that
holds the clock, calls ops->execute_tuning, and
releases the clock. Simplify the code a bit by
providing a separate function to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable power cycle and re-initialization of SD cards via the reset
bus_ops. Power cycling a buggy SD card sometimes helps it get back on
track.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In (3fcb027 ARM: MXC: mxcmmc: work around a bug in the SDHC busy line
handling) the optional init_card() callback was added. According to
the original change it was "for now only called from
mmc_sdio_init_card()".
This callback really ought to be called from the SD and MMC init
functions as well. One current user of this callback
(mxcmci_init_card) will not work as expected if you insert an SDIO
card, then eject it and put a normal SD card in. Specifically the
normal SD card will not get to run with 4-bit data.
I'd like to use the init_card() callback to handle a similar quirk on
dw_mmc when using SDIO Interrupts (the "low power" feature of the card
needs to be disabled), so that will add a second user of the function.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Timing mode identifier has same role and can take the place
of speed mode. This change removes all related speed mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Use new ATTRIBUTE_GROUPS macro to declare attribute groups.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Invoking system suspend or shutdown without using the Kconfig option
MMC_UNSAFE_RESUME, did trigger an ungraceful power cut of the card.
To improve the situation, change the behavior to always make use of the
available bus_ops callbacks that handles system suspend and shutdown
properly.
By changing the behavior MMC_UNSAFE_RESUME becomes redundant, so lets's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This reverts and updates commit 77776fd0a4 ("mmc: sd: fix the
maximum au_size for SD3.0"). The au_size for SD3.0 cannot be achieved
by a simple bit shift, so this needs to be implemented differently.
Also, don't print the warning in case of 0 since 'not defined' is
different from 'invalid'.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: stable <stable@vger.kernel.org> # [3.12, 3.13]
Signed-off-by: Chris Ball <chris@printf.net>
In some environments it is to prefer to postpone the resume of the card
device until runtime_resume is being carried out, since it will mean a
signficant decrease of the total system resume time.
The reason of the decreased resume time is simply because of the actual
re-initalization of the card, which typically takes hundreds of
milliseconds, is performed outside the resume sequence and wont thus
affect it.
For removable card, the detect work tries to re-detect the card to make
sure it is still present, as a part of that sequence the card will also
be runtime_resumed and thus also fully resumed.
For a non-removable card, typically a mmc blk request will trigger a
runtime_resume and thus fully resume the card. This also means the
first request will likely suffer from an inital latency since the
re-initialization of the card needs to be performed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The card device is considered as in-active after it has been suspended.
To prevent any further runtime PM requests in suspend state, we then
disable runtime PM.
After the card device has been resumed, we shall consider it as active,
like we also do after a probe sequence. When resumed, we can safely
enable runtime PM again.
This will make sure the PM core can request the card device to go to
in-active state after a resume has been completed. Previously we had to
wait for new pm_runtime_get->pm_runtime_put cycle to be executed.
Additionally, once a resume has been carried out, update the last busy
mark. At the moment this will have no effect but if the PM core will
respect autosuspend enabled devices, when it directly triggers a
runtime_suspend from a runtime_idle, it will mean the card device will
be scheduled for a delayed runtime_suspend instead of done immediately.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit "mmc: core: Push common suspend|resume code into each bus_ops"
moved the responsibility for doing mmc_power_up|off into each
suspend/resume bus_ops. When using MMC_CAP_AGGRESSIVE_PM, through the
runtime callbacks, calls to mmc_power_up|off became redundant.
When removing them, we are also able to remove the calls to
mmc_claim|release_host, thus simplifing code a bit more.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
By adding a card state that records if it is suspended or resumed, we
can accept asyncronus suspend/resume requests for the mmc and sd
bus_ops.
MMC_CAP_AGGRESSIVE_PM, will at request inactivity through the runtime
bus_ops callbacks, execute a suspend of the the card. In the state were
this has been done, we can receive a suspend request for the mmc bus,
which for sd and mmc forced the card to active state by a
pm_runtime_get_sync. In other words, the card was resumed and then
immediately suspended again, completely unnecessary.
Since the suspend/resume bus_ops callbacks for sd and mmc are now
capable of handling asynchronous requests, we no longer need to force
the card to active state before executing suspend. Evidently preventing
the above sequence for MMC_CAP_AGGRESSIVE_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since mmc_select_voltage now only gets called from the attach sequence,
it makes sense to move the out of spec validations of the card ocr into
this function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to eMMC/SD/SDIO specs, the VDD (VCC) voltage level must be
maintained during the initialization sequence. If we want/need to tune
the voltage level, a complete power cycle of the card must be executed.
Most host drivers conforms to the specifications by only allowing to
change VDD voltage level at the MMC_POWER_UP state, but some also cares
about MMC_POWER_ON state, which they should'nt. This patch will not
break those drivers, but they could clean up code to better reflect
what is expected from the protocol layer.
A big re-work of the mmc_select_voltage function is done to only change
VDD voltage level if the host supports MMC_CAP2_FULL_PWR_CYCLE.
Otherwise only validation of the host and card ocr mask will be done.
A very nice side-effect of this patch is that we now don't need to
reset the negotiated ocr mask at the mmc_power_off function, since now
it will actually reflect the present voltage level, which safely can be
used at the next power up and re-initialization. Moreover, we then only
need to execute mmc_select_voltage from the attach sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The negotiated ocr mask is directly related to the card. Once a card
gets removed, the mask shall be dropped. By moving the cache of the ocr
mask from the host struct to the card struct we have accomplished this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This is yet another step of restructure code to be able to fixup the
setup of the negotiated ocr mask.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As a step to fixup the setup of the negotiated ocr mask, we need the
mmc_power_up|cycle functions to take the ocr as a parameter.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since SD Physical Layer specification V3.0, AU_SIZE is supported up
to 0xf. So If SD-card is supported v3.0, then max_au should be 0xf.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In function mmc_sd_init_card, if command 3/9/7 got failed, mmc_card
allocated just before won't be freed. This would cause memory leak.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
For the SD .shutdown callback we re-use the SD suspend function since
it performs the relevant actions.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
By moving code from the mmc_suspend|resume_host down into each
.suspend|resume bus_ops callback, we get a more flexible solution.
Some nice side effects are that we get a better understanding of each
bus_ops suspend|resume sequence and the common code don't have to take
care of specific corner cases, especially for the SDIO case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Aggressive power management is suitable when saving power is
essential. At request inactivity timeout, aka pm runtime
autosuspend timeout, the card will be suspended.
Once a new request arrives, the card will be re-initalized and
thus the first request will suffer from a latency. This latency
is card-specific, experiments has shown in general that SD-cards
has quite poor initialization time, around 300ms-1100ms. eMMC is
not surprisingly far better but still a couple of hundreds of ms
has been observed.
Except for the request latency, it is important to know that
suspending the card will also prevent the card from executing
internal house-keeping operations in idle mode. This could mean
degradation in performance.
To use this feature make sure the request inactivity timeout is
chosen carefully. This has not been done as a part of this patch.
Enable this feature by using host cap MMC_CAP_AGGRESSIVE_PM and
by setting CONFIG_MMC_UNSAFE_RESUME.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Once the mmc blkdevice is being probed, runtime pm will be enabled.
By using runtime autosuspend, the power save operations can be done
when request inactivity occurs for a certain time. Right now the
selected timeout value is set to 3 s. Obviously this value will likely
need to be configurable somehow since it needs to be trimmed depending
on the power save algorithm.
For SD-combo cards, we are still leaving the enablement of runtime PM
to the SDIO init sequence since it depends on the capabilities of the
SDIO func driver.
Moreover, when the blk device is being suspended, we make sure the device
will be runtime resumed. The reason for doing this is that we want the
host suspend sequence to be unaware of any runtime power save operations
done for the card in this phase. Thus it can just handle the suspend as
the card is fully powered from a runtime perspective.
Finally, this patch prepares to make it possible to move BKOPS handling
into the runtime callbacks for the mmc bus_ops. Thus IDLE BKOPS can be
accomplished.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only execute tuning for sd and sdio devices that are using
SDR50 or SDR104.
Make sure clock is hold during tuning for sdio devices.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Acked-by: Johan Rudholm <jrudholm@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.
Below are the enhancements introduced by this patch:
1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one. The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.
2. In current code, preset value is disabled at the beginning of
mmc_attach_sd. It's too late since low freq (400khz) should be set in
mmc_power_up. So move preset value disable to sdhci_set_ios which will
be called during power up.
3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.
4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.
This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the
clock should be gated for 5 ms during the step. After enabling the
clock, the host should wait for at least 1 ms before checking for
failure. Failure by the card to switch is indicated by dat[0:3] being
pulled low. The host should check for this condition and power-cycle
the card if failure is indicated.
Add a retry mechanism for the SDIO case.
If the voltage switch fails repeatedly, give up and continue the
initialization using the original voltage.
This patch places a couple of requirements on the host driver:
1) mmc_set_ios with ios.clock = 0 must gate the clock
2) mmc_power_off must actually cut the power to the card
3) The card_busy host_ops member must be implemented
if these requirements are not fulfilled, the 1.8V signal voltage switch
will still be attempted but may not be successful.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.
Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a call to mmc_set_signal_voltage() to set signal voltage to 3.3v in
mmc_power_up so that we do not need to touch signal voltage setting in
mmc/sd/sdio init functions and rescan function.
For mmc/sd cards, when doing a suspend/resume cycle, consider the unsafe
resume case, the card will lose its power and when powered on again, we
will set signal voltage to 3.3v in mmc_power_up before its resume function
gets called, which will re-init the card.
And for sdio cards, when doing a suspend/resume cycle, consider the unsafe
resume case, the card will either lose its power or not depending on if it
wants to wakeup the host. If power is not maintained, it is the same case as
mmc/sd cards. If power is maintained, mmc_power_up will not be called and
the card's signal voltage will remain at the last setting.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
