EHRPWM hardware supports 2 independent PWM channels. However the device
uses only one register to handle period setting for both channels. So
both channels should be configured for same period (in nsec).
Fix the same by returning error for conflicting period values.
However, allow
1. Configuration of period settings if not conflicting with other
channels
2. Re-configuring of period settings if no other channels being
configured
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
APWM mode is enabled while configuring PWM device. This was done to
handle shadow & immediate mode update of period and compare registers.
However, leaving it enabled after configuring will cause APWM output on
PWM pin even before enabling PWM device.
Fix the same by disabling APWM mode after configuring if PWM device is
not running.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The __free_from_pool() function was changed in
e9da6e9905. Unfortunately, the test that
checks whether the provided (start,size) is within the DMA pool has
been improperly modified. It used to be:
if (start < coherent_head.vm_start || end > coherent_head.vm_end)
Where coherent_head.vm_end was non-inclusive (i.e, it did not include
the first byte after the pool). The test has been changed to:
if (start < pool->vaddr || start > pool->vaddr + pool->size)
So now pool->vaddr + pool->size is inclusive (i.e, it includes the
first byte after the pool), so the test should be >= instead of >.
This bug causes the following message when freeing the *first* DMA
coherent buffer that has been allocated, because its virtual address
is exactly equal to pool->vaddr + pool->size :
WARNING: at /home/thomas/projets/linux-2.6/arch/arm/mm/dma-mapping.c:463 __free_from_pool+0xa4/0xc0()
freeing wrong coherent size from pool
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Maen Suleiman <maen@marvell.com>
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Shadi Ammouri <shadi@marvell.com>
Cc: Eran Ben-Avi <benavi@marvell.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
[m.szyprowski: rebased onto v3.6-rc5 and resolved conflict]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This bug was triggered:
[ 4220.198458] BUG: unable to handle kernel paging request at fffffffffffffffe
[ 4220.203907] IP: [<ffffffff81104d85>] put_page+0xf/0x34
......
[ 4220.237326] Call Trace:
[ 4220.237361] [<ffffffffa03830d0>] kvm_arch_destroy_vm+0xf9/0x101 [kvm]
[ 4220.237382] [<ffffffffa036fe53>] kvm_put_kvm+0xcc/0x127 [kvm]
[ 4220.237401] [<ffffffffa03702bc>] kvm_vcpu_release+0x18/0x1c [kvm]
[ 4220.237407] [<ffffffff81145425>] __fput+0x111/0x1ed
[ 4220.237411] [<ffffffff8114550f>] ____fput+0xe/0x10
[ 4220.237418] [<ffffffff81063511>] task_work_run+0x5d/0x88
[ 4220.237424] [<ffffffff8104c3f7>] do_exit+0x2bf/0x7ca
The test case:
printf(fmt, ##args); \
exit(-1);} while (0)
static int create_vm(void)
{
int sys_fd, vm_fd;
sys_fd = open("/dev/kvm", O_RDWR);
if (sys_fd < 0)
die("open /dev/kvm fail.\n");
vm_fd = ioctl(sys_fd, KVM_CREATE_VM, 0);
if (vm_fd < 0)
die("KVM_CREATE_VM fail.\n");
return vm_fd;
}
static int create_vcpu(int vm_fd)
{
int vcpu_fd;
vcpu_fd = ioctl(vm_fd, KVM_CREATE_VCPU, 0);
if (vcpu_fd < 0)
die("KVM_CREATE_VCPU ioctl.\n");
printf("Create vcpu.\n");
return vcpu_fd;
}
static void *vcpu_thread(void *arg)
{
int vm_fd = (int)(long)arg;
create_vcpu(vm_fd);
return NULL;
}
int main(int argc, char *argv[])
{
pthread_t thread;
int vm_fd;
(void)argc;
(void)argv;
vm_fd = create_vm();
pthread_create(&thread, NULL, vcpu_thread, (void *)(long)vm_fd);
printf("Exit.\n");
return 0;
}
It caused by release kvm->arch.ept_identity_map_addr which is the
error page.
The parent thread can send KILL signal to the vcpu thread when it was
exiting which stops faulting pages and potentially allocating memory.
So gfn_to_pfn/gfn_to_page may fail at this time
Fixed by checking the page before it is used
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
snd_hda_codec_reset() calls restore_pincfgs() where the codec is
powered up again, which eventually tries to resume and initialize via
the callbacks of the codec. However, it's the place just after codec
free callback, thus no codec callbacks should be called after that.
On a codec like CS4206, it results in Oops due to the access in init
callback.
This patch fixes the issue by clearing the codec callbacks properly
after freeing codec.
Reported-by: Daniel J Blueman <daniel@quora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If kernel is compiled with CONFIG_PROVE_LOCKING the
validator raises an error when a multiplexer is removed
via sysfs and sub-clients are connected to it. This is a
false positive.
Documentation/lockdep-design.txt recommends to handle this
via calls to mutex_lock_nested().
Based on an earlier fix from Michael Lawnick.
Note that the extra code resolves to nothing unless
CONFIG_DEBUG_LOCK_ALLOC=y.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.
Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.
This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:
LD drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org [3.2+]
Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We spare nothing by not validating the sequence number of dataless
ACK packets and enabling it makes harder off-path attacks.
See: "Reflection scan: an Off-Path Attack on TCP" by Jan Wrobel,
http://arxiv.org/abs/1201.2074
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Clients should not send such packets. By accepting them, we open
up a hole by wich ephemeral ports can be discovered in an off-path
attack.
See: "Reflection scan: an Off-Path Attack on TCP" by Jan Wrobel,
http://arxiv.org/abs/1201.2074
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The delay functions may be called by some platforms between switching to
the timer-based delay loop but before calibration. In this case, the
initial loops_per_jiffy may not be suitable for the timer (although a
compromise may be achievable) and delay times may be considered too
inaccurate.
This patch updates loops_per_jiffy when switching to the timer-based
delay loop so that delays are consistent prior to calibration.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The user access functions may generate a fault, resulting in invocation
of a handler that may sleep.
This patch annotates the accessors with might_fault() so that we print a
warning if they are invoked from atomic context and help lockdep keep
track of mmap_sem.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The {get,put}_user macros don't perform range checking on the provided
__user address when !CPU_HAS_DOMAINS.
This patch reworks the out-of-line assembly accessors to check the user
address against a specified limit, returning -EFAULT if is is out of
range.
[will: changed get_user register allocation to match put_user]
[rmk: fixed building on older ARM architectures]
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Checks and operations on the INVPCID feature bit should use EBX
of CPUID leaf 7 instead of ECX.
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Signed-off-by: Yongjie Ren <yongjien.ren@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit e9da6e9905 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
In the current rxhash calculation function, while the
sorting of the ports/addrs is coherent (you get the
same rxhash for packets sharing the same 4-tuple, in
both directions), ports and addrs are sorted
independently. This implies packets from a connection
between the same addresses but crossed ports hash to
the same rxhash.
For example, traffic between A=S:l and B=L:s is hashed
(in both directions) from {L, S, {s, l}}. The same
rxhash is obtained for packets between C=S:s and D=L:l.
This patch ensures that you either swap both addrs and ports,
or you swap none. Traffic between A and B, and traffic
between C and D, get their rxhash from different sources
({L, S, {l, s}} for A<->B, and {L, S, {s, l}} for C<->D)
The patch is co-written with Eric Dumazet <edumazet@google.com>
Signed-off-by: Chema Gonzalez <chema@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This thing is killing lockdep.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
[Jani: move the init next to the other spin lock inits]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
file that affect booting on various omaps. Then some PM
related fixes for reset, sleep and wakeup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fUO5
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for timer, sram, memory corruption, and one board file that affect
booting on various omaps. Then some PM related fixes for reset, sleep
and wakeup.
* tag 'omap-fixes-for-v3.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: Fix array size for irq_target_cpu
ARM: OMAP4: hwmod data: temporarily comment out data for the sl2if IP block
ARM: OMAP: hwmod code: Disable module when hwmod enable fails
ARM: OMAP3: hwmod data: fix iva2 reset info
ARM: OMAP3xxx: clockdomain: fix software supervised wakeup/sleep
ARM: OMAP2+: am33xx: Fix the timer fck clock naming convention
ARM: OMAP: Config fix for omap3-touchbook board
ARM: OMAP: sram: skip the first 16K on OMAP3 HS
ARM: OMAP: sram: fix OMAP4 errata handling
ARM: OMAP: timer: obey the !CONFIG_OMAP_32K_TIMER
get_user may fail to load from the provided __user address due to an
unhandled fault generated by the access.
In the case of the undefined instruction trap, this results in failure
to load the faulting instruction, in which case we should send SIGILL to
the task rather than continue with potentially uninitialised data.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems we were missing some text in the title for the
semihosting DEBUG_LL option. Add in the "/O" and fix up some
minor typos in the help text.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
'make dtbs' in a clean tree will try running the dtc before actually
building it. Make these rules depend upon the scripts to build it.
Cc: <stable@vger.kernel.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During the p2v changes, the PHYS_OFFSET #define moved into a
!__ASSEMBLY__ section. This causes a XIP build to fail with
arch/arm/kernel/head.o: In function 'stext':
arch/arm/kernel/head.S:146: undefined reference to 'PHYS_OFFSET'
Momentarily leave the #ifndef __ASSEMBLY__ section so we can
define PHYS_OFFSET for all compilation units.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull HID updates from Jiri Kosina:
"It contains a fix for Eaton Ellipse MAX UPS from Alan Stern,
performance improvement (not processing debug data if noone is
interested), by Henrik Rydberg, and allowing tpkbd-driven devices to
work even with generic driver in a crippled mode, by Andres Freund."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
HID: Only dump input if someone is listening
HID: add NOGET quirk for Eaton Ellipse MAX UPS
John W. Linville says:
====================
Please pull these fixes intended for 3.6. There are more commits
here than I would like -- I got a bit behind while I was stalking
Steven Rostedt in San Diego last week... I'll slow it down after this!
There are a couple of pulls here. One is from Johannes:
"Please pull (according to the below information) to get a few fixes.
* a fix to properly disconnect in the driver when authentication or
association fails
* a fix to prevent invalid information about mesh paths being reported
to userspace
* a memory leak fix in an nl80211 error path"
The other comes via Gustavo:
"A few updates for the 3.6 kernel. There are two btusb patches to add
more supported devices through the new USB_VENDOR_AND_INTEFACE_INFO()
macro and another one that add a new device id for a Sony Vaio laptop,
one fix for a user-after-free and, finally, two patches from Vinicius
to fix a issue in SMP pairing."
Along with those...
Arend van Spriel provides a fix for a use-after-free bug in brcmfmac.
Daniel Drake avoids a hang by not trying to touch the libertas hardware
duing suspend if it is already powered-down.
Felix Fietkau provides a batch of ath9k fixes that adress some
potential problems with power settings, as well as a fix to avoid a
potential interrupt storm.
Gertjan van Wingerde provides a register-width fix for rt2x00, and
a rt2x00 fix to prevent incorrectly detecting the rfkill status.
He also provides a device ID patch.
Hante Meuleman gives us three brcmfmac fixes, one that properly
initializes a command structure, one that fixes a race condition that
could lose usb requests, and one that removes some log spam.
Marc Kleine-Budde offers an rt2x00 fix for a voltage setting on some
specific devices.
Mohammed Shafi Shajakhan sent an ath9k fix to avoid a crash related to
using timers that aren't allocated when 2 wire bluetooth coexistence
hardware is in use.
Sergei Poselenov changes rt2800usb to do some validity checking for
received packets, avoiding crashes on an ARM Soc.
Stone Piao gives us an mwifiex fix for an incorrectly set skb length
value for a command buffer.
All of these are localized to their specific drivers, and relatively
small. The power-related patches from Felix are bigger than I would
like, but I merged them in consideration of their isolation to ath9k
and the sensitive nature of power settings in wireless devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that spc_emulate_request_sense has been taught to process zero-length
REQUEST SENSE correctly, drop the special handling of unit attention
conditions from transport_generic_new_cmd. However, for now REQUEST SENSE
will be the only command that goes through emulation for zero lengths.
(nab: Fix up zero-length check in transport_generic_new_cmd)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Similar to INQUIRY and MODE SENSE, construct the sense data in a
buffer and later copy it to the scatterlist. Do not do anything,
but still clear a pending unit attention condition, if the allocation
length is zero.
However, SPC tells us that "If a REQUEST SENSE command is terminated with
CHECK CONDITION status [and] the REQUEST SENSE command was received on
an I_T nexus with a pending unit attention condition (i.e., before the
device server reports CHECK CONDITION status), then the device server
shall not clear the pending unit attention condition." Do the
transport_kmap_data_sg early to detect this case.
It also tells us "Device servers shall not adjust the additional sense
length to reflect truncation if the allocation length is less than the
sense data available", so do not do that! Note that the err variable
is write-only.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to support zero-size allocation lengths, do not assert
that we have a scatterlist until after checking cmd->data_length.
But once we do this, we can have two cases of transport_kmap_data_sg
returning NULL: a zero-size allocation length, or an out-of-memory
condition. Report the latter using sense codes, so that the SCSI
command that triggered it will fail.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SPC says:
"The ALLOCATION LENGTH field is defined in 4.3.5.6. The allocation length
should be at least 16. Device servers compliant with SPC return CHECK
CONDITION status, with the sense key set to ILLEGAL REQUEST, and the
additional sense code set to INVALID FIELD IN CDB when the allocation
length is less than 16 bytes".
Testcase: sg_raw -r8 /dev/sdb a0 00 00 00 00 00 00 00 00 08 00 00
should fail with ILLEGAL REQUEST / INVALID FIELD IN CDB sense
does not fail without the patch
fails correctly with the patch
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Several places were not checking that the parameter list length
was large enough, and thus accessing invalid memory. Zero-length
parameter lists are just a special case of this.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Right now, commands with a zero-size payload are skipped completely.
This is wrong; such commands should be passed down to the device and
processed normally.
For physical backends, this ignores completely things such as START
STOP UNIT. For virtual backends, we have a hack in place to clear a
unit attention state on a zero-size REQUEST SENSE, but we still do
not report errors properly on zero-length commands---out-of-bounds
0-block reads and writes, too small parameter list lengths, etc.
This patch fixes this for PSCSI. Uses of transport_kmap_data_sg are
guarded with a check for non-zero cmd->data_length; for all other
commands a zero length is handled properly in pscsi_execute_cmd.
The sole exception will be for now REPORT LUNS, which is handled
through the normal SPC emulation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It doesn't seem this spinlock was properly initialized.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In UDP recvmsg(), we miss an increase of UDP_MIB_INERRORS if the copy
of skb to userspace failed for whatever reason.
Reported-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_cmd_init() failed, the init_one function returned
success, although no resources were opened.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order of operations was wrong on the teardown flow.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The search for promisc entries was always done on the first port,
While the addition is done on the correct port.
This lead to resource leackage of promisc entries on the second
port and brought to a state where we could no longer enter to
promiscuous mode after enough iterations of "ifconfig promisc"
on the second port.
Fix that by using the correct port when searching.
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since VFs may be mapped to VMs which aren't trusted entities, flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that their L2 specification relate to MAC address
assigned to that VF, and add L2 specification if its missing.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 43cedbf0e8 (SUNRPC: Ensure that
we grab the XPRT_LOCK before calling xprt_alloc_slot) is causing
hangs in the case of NFS over UDP mounts.
Since neither the UDP or the RDMA transport mechanism use dynamic slot
allocation, we can skip grabbing the socket lock for those transports.
Add a new rpc_xprt_op to allow switching between the TCP and UDP/RDMA
case.
Note that the NFSv4.1 back channel assigns the slot directly
through rpc_run_bc_task, so we can ignore that case.
Reported-by: Dick Streefland <dick.streefland@altium.nl>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org [>= 3.1]
Here's a rather big set of fixes for v3.6-rc4.
There are some fixes for bugs which have been pending for a long
time and only now were uncovered, like the musb and dwc3 patches.
We have some remaining fixes for the ep->desc patch series from
Ido, a fix for renesas DMA usage, IRQ check on musb's DMA and
an oops fix on musb Host implementation.
All patches have been pending on linux-usb for a long time and
shouldn't cause any further regressions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F4Vw
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into work-linus
usb: fixes for v3.6-rc4
Here's a rather big set of fixes for v3.6-rc4.
There are some fixes for bugs which have been pending for a long
time and only now were uncovered, like the musb and dwc3 patches.
We have some remaining fixes for the ep->desc patch series from
Ido, a fix for renesas DMA usage, IRQ check on musb's DMA and
an oops fix on musb Host implementation.
All patches have been pending on linux-usb for a long time and
shouldn't cause any further regressions.
c1dcad2d32 added a new driver configured by
HID_LENOVO_TPKBD but made the hid_have_special_driver entry non-optional which
lead to a recognized but non-working device if the new driver wasn't
configured (which is the correct default).
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Replace blackfin ipi message queue with generic smp helper function.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
This will cause udev to load vmwgfx instead of waiting for X
to do it.
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The I2S controllers are programmed with an "attention" level of 4 DWORDs.
This must match the configuration passed to the DMA driver, so that when
they burst in data, they don't overflow the available FIFO space. Also,
the burst size is relevant to the destination for playback, and source
for capture, not vice-versa as originally written.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQSS7TAAoJEFjIrFwIi8fJOBQH/03JBKBbFvewhop8T5Jww2c9
SWmMgzDm5HkxeWj5XnM+zlLoHrYFFu7tyuRLiny4weE0LdRl4adJ1TVpStxap/b6
MSQKe+tZevslaReBOsMpbCk3z7fEWNlAcpm6wMp1xYmLoHcr0JMpOCmzigbf7dwM
F4UWULheih9ME3UeqDAU8qgvfv6ccZ9vempO4TDWKjxfxfWODCNMRx+Ny+C7NNRk
QeoInHJUqcRkg0q0OIciF/YYDmn8hIH7HgfqomuMb6rEv2LOieLnWVuniEPWM75s
lECxro7v2Z9s1Std0WWKcFp8VZpI2scnQYU8aL8TpewHcbzKHQYyipuKPu7FiEQ=
=GfLE
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
* tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Fix proper FLR steps.
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zFNa
-----END PGP SIGNATURE-----
Merge tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled"
* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't print anything while decoding is disabled
PCI/PM: Add ABI document for sysfs file d3cold_allowed
PCI/PM: Fix config reg access for D3cold and bridge suspending
PCI/PM: Keep parent bridge active when probing device
PCI/PM: Enable D3/D3cold by default for most devices
In 3.6-rc3, without this patch, the following error occurs with a modular build:
ERROR: "gen_split_key" [drivers/crypto/caam/caamhash.ko] undefined!
ERROR: "gen_split_key" [drivers/crypto/caam/caamalg.ko] undefined!
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Yuan Kang <Yuan.Kang@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If decode_getfh failed, nfs4_xdr_dec_open would return 0 since the last
decode_* call must have succeeded.
Cc: stable@vger.kernel.org
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
