Split 6G band into 8 sub-bands where indexes are from 0 to 7,
i.e. RTW89_CH_6G_BAND_IDX[0-7]. Then, decide subband by both
band and channel instead of just channel because conflicts
between 5G channels and 6G channels.
Moreover, add default case to the existing use of switch (subband).
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-4-pkshih@realtek.com
Since these macro in rfk helpers are common now, a common naming
should be better. So, apply RTW89_ as prefix to them, and modify
the use correspondly. No logic is changed at all.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-3-pkshih@realtek.com
These rfk helpers are also useful for the chip which is under planning.
So, move them to common code to avoid duplicate stuff in the future.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-2-pkshih@realtek.com
BCM43454/6 is a variant of BCM4345 which is exactly identical to
BCM4345/6, except the chip id is 0xa9be. This patch adds support
for BCM43454/6 by handing it in the same way as BCM4345.
Note: when loading some specific version of BCM4345 firmware, the
chip id may become 0x4345. This is an expected behavior, and it will
restore to 0xa9be after power cycle.
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/CO1PR11MB47859B51BCA88613D1582EB88E2E9@CO1PR11MB4785.namprd11.prod.outlook.com
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmIGLrkRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZsgWAf/aQb18PB2Wh+tH4qxkNW6jK3zfYSRDbDQ
QvrHcnN4BINorTLcGDvWqw3VANiETCW6mVBG8BWo1NyAlvkNziKaAFI3xVhuOE38
6d+wRVElG9JHeb6OwWCX2vWJmqWVxmEIAkTQrqT9VSSUjGDpS1mc3dAssABeEZhn
yzSKJomSRaRv/aC2f/4eYPAyeMUIZbN3VWFOvElGPls0mdrSBmt9OhAKkf3A3E0M
PuJzhnHgoKhpZ/Gmn+IrDZGC/RkUOfT2zZ5gUK0GVvpTFg2/80ilC7RJk2iF5Ibs
xGuRN9WSo9xWILF3SyRgrrx3ocZG0H2dvkJj4ZQbR485U8iXa+HC1g==
=AUlw
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-02-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
wireless-next patches for v5.18
First set of patches for v5.18, with both wireless and stack patches.
rtw89 now has AP mode support and wcn36xx has survey support. But
otherwise pretty normal.
Major changes:
ath11k
* add LDPC FEC type in 802.11 radiotap header
* enable RX PPDU stats in monitor co-exist mode
wcn36xx
* implement survey reporting
brcmfmac
* add CYW43570 PCIE device
rtw88
* rtw8821c: enable RFE 6 devices
rtw89
* AP mode support
mt76
* mt7916 support
* background radar detection support
Eric Dumazet says:
====================
ipv6: remove addrconf reliance on loopback
Second patch in this series removes IPv6 requirement about the netns
loopback device being the last device being dismantled.
This was needed because rt6_uncached_list_flush_dev()
and ip6_dst_ifdown() had to switch dst dev to a known
device (loopback).
Instead of loopback, we can use the (hidden) blackhole_netdev
which is also always there.
This will allow future simplfications of netdev_run_to()
and other parts of the stack like default_device_exit_batch().
Last two patches are optimizations for both IP families.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an optimization to keep the per-cpu lists as short as possible:
Whenever rt_flush_dev() changes one rtable dst.dev
matching the disappearing device, it can can transfer the object
to a quarantine list, waiting for a final rt_del_uncached_list().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an optimization to keep the per-cpu lists as short as possible:
Whenever rt6_uncached_list_flush_dev() changes one rt6_info
matching the disappearing device, it can can transfer the object
to a quarantine list, waiting for a final rt6_uncached_list_del().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 addrconf notifiers wants the loopback device to
be the last device being dismantled at netns deletion.
This caused many limitations and work arounds.
Back in linux-5.3, Mahesh added a per host blackhole_netdev
that can be used whenever we need to make sure objects no longer
refer to a disappearing device.
If we attach to blackhole_netdev an ip6_ptr (allocate an idev),
then we can use this special device (which is never freed)
in place of the loopback_dev (which can be freed).
This will permit improvements in netdev_run_todo() and other parts
of the stack where had steps to make sure loopback_dev was
the last device to disappear.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter has never been visible, there is little point
trying to maintain it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352, mv88e6240 and mv88e6176 have a serdes interface. This patch
allows to configure the output swing to a desired value in the
phy-handle of the port. The value which is peak to peak has to be
specified in microvolts. As the chips only supports eight dedicated
values we return EINVAL if the value in the DTS does not match one of
these values.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Common PHYs and network PCSes often have the possibility to specify
peak-to-peak voltage on the differential pair - the default voltage
sometimes needs to be changed for a particular board.
Add properties `tx-p2p-microvolt` and `tx-p2p-microvolt-names` for this
purpose. The second property is needed to specify the mode for the
corresponding voltage in the `tx-p2p-microvolt` property, if the voltage
is to be used only for speficic mode. More voltage-mode pairs can be
specified.
Example usage with only one voltage (it will be used for all supported
PHY modes, the `tx-p2p-microvolt-names` property is not needed in this
case):
tx-p2p-microvolt = <915000>;
Example usage with voltages for multiple modes:
tx-p2p-microvolt = <915000>, <1100000>, <1200000>;
tx-p2p-microvolt-names = "2500base-x", "usb", "pcie";
Add these properties into a separate file phy/transmit-amplitude.yaml,
which should be referenced by any binding that uses it.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->rtm_tos option is normally used to route packets based on both
the destination address and the DS field. However it's ignored for
IPv6 routes. Setting ->rtm_tos for IPv6 is thus invalid as the route
is going to work only on the destination address anyway, so it won't
behave as specified.
Suggested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
More aggressive DSA cleanup
This series deletes some code which is apparently not needed.
I've had these patches in my tree for a while, and testing on my boards
didn't reveal any issues.
Compared to the RFC v1 series, the only change is the addition of patch 3.
https://patchwork.kernel.org/project/netdevbpf/cover/20220107184842.550334-1-vladimir.oltean@nxp.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), suggested by Cong Wang, the
DSA interfaces and their master have different dev->nested_level, which
makes netif_addr_lock() stop complaining about potentially recursive
locking on the same lock class.
So we no longer need DSA slave interfaces to have their own lockdep
class.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), suggested by Cong Wang, the
DSA interfaces and their master have different dev->nested_level, which
makes netif_addr_lock() stop complaining about potentially recursive
locking on the same lock class.
So we no longer need DSA masters to have their own lockdep class.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no legacy ports, DSA registers a devlink instance with ports
unconditionally for all switch drivers. Therefore, delete the old-style
ndo operations used for determining bridge forwarding domains.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
D. Wythe says:
====================
net/smc: Optimizing performance in short-lived scenarios
This patch set aims to optimizing performance of SMC in short-lived
links scenarios, which is quite unsatisfactory right now.
In our benchmark, we test it with follow scripts:
./wrk -c 10000 -t 4 -H 'Connection: Close' -d 20 http://smc-server
Current performance figures like that:
Running 20s test @ http://11.213.45.6
4 threads and 10000 connections
4956 requests in 20.06s, 3.24MB read
Socket errors: connect 0, read 0, write 672, timeout 0
Requests/sec: 247.07
Transfer/sec: 165.28KB
There are many reasons for this phenomenon, this patch set doesn't
solve it all though, but it can be well alleviated with it in.
Patch 1/5 (Make smc_tcp_listen_work() independent) :
Separate smc_tcp_listen_work() from smc_listen_work(), make them
independent of each other, the busy SMC handshake can not affect new TCP
connections visit any more. Avoid discarding a large number of TCP
connections after being overstock, which is undoubtedly raise the
connection establishment time.
Patch 2/5 (Limit SMC backlog connections):
Since patch 1 has separated smc_tcp_listen_work() from
smc_listen_work(), an unrestricted TCP accept have come into being. This
patch try to put a limit on SMC backlog connections refers to
implementation of TCP.
Patch 3/5 (Limit SMC visits when handshake workqueue congested):
Considering the complexity of SMC handshake right now, in short-lived
links scenarios, this may not be the main scenario of SMC though, it's
performance is still quite poor. This patch try to provide constraint on
SMC handshake when handshake workqueue congested, which is the sign of
SMC handshake stacking in our opinion.
Patch 4/5 (Dynamic control handshake limitation by socket options)
This patch allow applications dynamically control the ability of SMC
handshake limitation. Since SMC don't support set SMC socket option
before,
this patch also have to support SMC's owns socket options.
Patch 5/5 (Add global configure for handshake limitation by netlink)
This patch provides a way to get benefit of handshake limitation
without
modifying any code for applications, which is quite useful for most
existing applications.
After this patch set, performance figures like that:
Running 20s test @ http://11.213.45.6
4 threads and 10000 connections
693253 requests in 20.10s, 452.88MB read
Requests/sec: 34488.13
Transfer/sec: 22.53MB
That's a quite well performance improvement, about to 6 to 7 times in my
environment.
---
changelog:
v1 -> v2:
- fix compile warning
- fix invalid dependencies in kconfig
v2 -> v3:
- correct spelling mistakes
- fix useless variable declare
v3 -> v4
- make smc_tcp_ls_wq be static
v4 -> v5
- add dynamic control for SMC auto fallback by socket options
- add global configure for SMC auto fallback through netlink
v5 -> v6
- move auto fallback to net namespace scope
- remove auto fallback attribute in SMC_GEN_SYS_INFO
- add independent attributes for auto fallback
v6 -> v7
- fix wording and the naming issues, rename 'auto fallback' to handshake
limitation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we can control SMC handshake limitation through socket options,
which means that applications who need it must modify their code. It's
quite troublesome for many existing applications. This patch modifies
the global default value of SMC handshake limitation through netlink,
providing a way to put constraint on handshake without modifies any code
for applications.
Suggested-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to add dynamic control for SMC handshake limitation for
every smc sockets, in production environment, it is possible for the
same applications to handle different service types, and may have
different opinion on SMC handshake limitation.
This patch try socket options to complete it, since we don't have socket
option level for SMC yet, which requires us to implement it at the same
time.
This patch does the following:
- add new socket option level: SOL_SMC.
- add new SMC socket option: SMC_LIMIT_HS.
- provide getter/setter for SMC socket options.
Link: https://lore.kernel.org/all/20f504f961e1a803f85d64229ad84260434203bd.1644323503.git.alibuda@linux.alibaba.com/
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch intends to provide a mechanism to put constraint on SMC
connections visit according to the pressure of SMC handshake process.
At present, frequent visits will cause the incoming connections to be
backlogged in SMC handshake queue, raise the connections established
time. Which is quite unacceptable for those applications who base on
short lived connections.
There are two ways to implement this mechanism:
1. Put limitation after TCP established.
2. Put limitation before TCP established.
In the first way, we need to wait and receive CLC messages that the
client will potentially send, and then actively reply with a decline
message, in a sense, which is also a sort of SMC handshake, affect the
connections established time on its way.
In the second way, the only problem is that we need to inject SMC logic
into TCP when it is about to reply the incoming SYN, since we already do
that, it's seems not a problem anymore. And advantage is obvious, few
additional processes are required to complete the constraint.
This patch use the second way. After this patch, connections who beyond
constraint will not informed any SMC indication, and SMC will not be
involved in any of its subsequent processes.
Link: https://lore.kernel.org/all/1641301961-59331-1-git-send-email-alibuda@linux.alibaba.com/
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation does not handling backlog semantics, one
potential risk is that server will be flooded by infinite amount
connections, even if client was SMC-incapable.
This patch works to put a limit on backlog connections, referring to the
TCP implementation, we divides SMC connections into two categories:
1. Half SMC connection, which includes all TCP established while SMC not
connections.
2. Full SMC connection, which includes all SMC established connections.
For half SMC connection, since all half SMC connections starts with TCP
established, we can achieve our goal by put a limit before TCP
established. Refer to the implementation of TCP, this limits will based
on not only the half SMC connections but also the full connections,
which is also a constraint on full SMC connections.
For full SMC connections, although we know exactly where it starts, it's
quite hard to put a limit before it. The easiest way is to block wait
before receive SMC confirm CLC message, while it's under protection by
smc_server_lgr_pending, a global lock, which leads this limit to the
entire host instead of a single listen socket. Another way is to drop
the full connections, but considering the cast of SMC connections, we
prefer to keep full SMC connections.
Even so, the limits of full SMC connections still exists, see commits
about half SMC connection below.
After this patch, the limits of backend connection shows like:
For SMC:
1. Client with SMC-capability can makes 2 * backlog full SMC connections
or 1 * backlog half SMC connections and 1 * backlog full SMC
connections at most.
2. Client without SMC-capability can only makes 1 * backlog half TCP
connections and 1 * backlog full TCP connections.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multithread and 10K connections benchmark, the backend TCP connection
established very slowly, and lots of TCP connections stay in SYN_SENT
state.
Client: smc_run wrk -c 10000 -t 4 http://server
the netstate of server host shows like:
145042 times the listen queue of a socket overflowed
145042 SYNs to LISTEN sockets dropped
One reason of this issue is that, since the smc_tcp_listen_work() shared
the same workqueue (smc_hs_wq) with smc_listen_work(), while the
smc_listen_work() do blocking wait for smc connection established. Once
the workqueue became congested, it's will block the accept() from TCP
listen.
This patch creates a independent workqueue(smc_tcp_ls_wq) for
smc_tcp_listen_work(), separate it from smc_listen_work(), which is
quite acceptable considering that smc_tcp_listen_work() runs very fast.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schema changes:
- support for mdio-connected switches (mdio driver), recognized by
checking the presence of property "reg"
- new compatible strings for rtl8367s and rtl8367rb
- "interrupt-controller" was not added as a required property. It might
still work polling the ports when missing.
Examples changes:
- renamed "switch_intc" to make it unique between examples
- removed "dsa-mdio" from mdio compatible property
- renamed phy@0 to ethernet-phy@0 (not tested with real HW)
phy@ requires #phy-cells
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - new code bugs:
- sparx5: fix get_stat64 out-of-bound access and crash
- smc: fix netdev ref tracker misuse
Previous releases - regressions:
- eth: ixgbevf: require large buffers for build_skb on 82599VF,
avoid overflows
- eth: ocelot: fix all IP traffic getting trapped to CPU with PTP
over IP
- bonding: fix rare link activation misses in 802.3ad mode
Previous releases - always broken:
- tcp: fix tcp sock mem accounting in zero-copy corner cases
- remove the cached dst when uncloning an skb dst and its metadata,
since we only have one ref it'd lead to an UaF
- netfilter:
- conntrack: don't refresh sctp entries in closed state
- conntrack: re-init state for retransmitted syn-ack, avoid
connection establishment getting stuck with strange stacks
- ctnetlink: disable helper autoassign, avoid it getting lost
- nft_payload: don't allow transport header access for fragments
- dsa: fix use of devres for mdio throughout drivers
- eth: amd-xgbe: disable interrupts during pci removal
- eth: dpaa2-eth: unregister netdev before disconnecting the PHY
- eth: ice: fix IPIP and SIT TSO offload
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=jlhJ
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter and can.
Current release - new code bugs:
- sparx5: fix get_stat64 out-of-bound access and crash
- smc: fix netdev ref tracker misuse
Previous releases - regressions:
- eth: ixgbevf: require large buffers for build_skb on 82599VF, avoid
overflows
- eth: ocelot: fix all IP traffic getting trapped to CPU with PTP
over IP
- bonding: fix rare link activation misses in 802.3ad mode
Previous releases - always broken:
- tcp: fix tcp sock mem accounting in zero-copy corner cases
- remove the cached dst when uncloning an skb dst and its metadata,
since we only have one ref it'd lead to an UaF
- netfilter:
- conntrack: don't refresh sctp entries in closed state
- conntrack: re-init state for retransmitted syn-ack, avoid
connection establishment getting stuck with strange stacks
- ctnetlink: disable helper autoassign, avoid it getting lost
- nft_payload: don't allow transport header access for fragments
- dsa: fix use of devres for mdio throughout drivers
- eth: amd-xgbe: disable interrupts during pci removal
- eth: dpaa2-eth: unregister netdev before disconnecting the PHY
- eth: ice: fix IPIP and SIT TSO offload"
* tag 'net-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (53 commits)
net: dsa: mv88e6xxx: fix use-after-free in mv88e6xxx_mdios_unregister
net: mscc: ocelot: fix mutex lock error during ethtool stats read
ice: Avoid RTNL lock when re-creating auxiliary device
ice: Fix KASAN error in LAG NETDEV_UNREGISTER handler
ice: fix IPIP and SIT TSO offload
ice: fix an error code in ice_cfg_phy_fec()
net: mpls: Fix GCC 12 warning
dpaa2-eth: unregister the netdev before disconnecting from the PHY
skbuff: cleanup double word in comment
net: macb: Align the dma and coherent dma masks
mptcp: netlink: process IPv6 addrs in creating listening sockets
selftests: mptcp: add missing join check
net: usb: qmi_wwan: Add support for Dell DW5829e
vlan: move dev_put into vlan_dev_uninit
vlan: introduce vlan_dev_free_egress_priority
ax25: fix UAF bugs of net_device caused by rebinding operation
net: dsa: fix panic when DSA master device unbinds on shutdown
net: amd-xgbe: disable interrupts during pci removal
tipc: rate limit warning for received illegal binding update
net: mdio: aspeed: Add missing MODULE_DEVICE_TABLE
...
This Kselftest fixes updated for Linux 5.17-rc4 consists of build and
run-time fixes to pidfd, clone3, and ir tests.
-----BEGIN PGP SIGNATURE-----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=UT3I
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-fixes-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
"Build and run-time fixes to pidfd, clone3, and ir tests"
* tag 'linux-kselftest-fixes-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/ir: fix build with ancient kernel headers
selftests: fixup build warnings in pidfd / clone3 tests
pidfd: fix test failure due to stack overflow on some arches
This KUnit fixes update for Linux 5.17-rc4 consists of bug fixes
to the test and usage documentation.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPZKym/RZuOCGeA/kCwJExA0NQxwFAmIFYvMACgkQCwJExA0N
QxxO2xAA40u5YaQ7U2hJgHQr1Oh5CIW8z62EiHHa2o59tbkmcaeAfd6O2iHEbKSp
hWB4DJkod61PLtzQLFIH7uKDKiRfljygSuPaAH+igCo5qKAIXlhpE01DBGbVa+68
ULyi8s78Ak39R9pZsMqm9diDUGdxQVUjDPpEjDQNBxOSJDaHVUeqKu5k3OKKhJf0
2JMbZxLWYTc1V5DmCFgjFn+qGqIbfEgB4ghFSWnwdwT+wjVUrl3UKTYseu5OrmUf
gNwXMfd7qir4dHfLbZYN6ztlLdD85fUUWeRKTPw7wXnPvRjW/X9FutU1/FxF6ihU
4mcoKWw0joPV+6GGQCwrxhaL6giozLS4iSpwe6mKI+MyJrpclG7znj5JDqvxUqBK
jHe8kOS0fyOTQrtnQQ7mlaQYMSzGQYz+TKmIuA0jTUDU+BaLEciwFSsZL6feFhbb
F1xTrzSF2etb98r5Dk/OPwhUvk0+xDO/SVUsFEgE51Kd42pLldakR0wodDvdqOfh
2rUib/xunWaOxIWMSwjOFuW6N0yDZNgNci0mo4ZxZJoHhpEH0Qt3MIhbdNDtXD/0
nZFmPQrGbIU9VZdl80O1ut8xtph4tCqwLfI2zfyXIAKzPVFLvu2MLWERQgrdUh1P
rLkEUwUbug97hJQnRzV7q5l436kUV5IPyBsFzaIJcIpGPi8L60I=
=EqMn
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit fixes from Shuah Khan:
"Fixes to the test and usage documentation"
* tag 'linux-kselftest-kunit-fixes-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
Documentation: KUnit: Fix usage bug
kunit: fix missing f in f-string in run_checks.py
Since struct mv88e6xxx_mdio_bus *mdio_bus is the bus->priv of something
allocated with mdiobus_alloc_size(), this means that mdiobus_free(bus)
will free the memory backing the mdio_bus as well. Therefore, the
mdio_bus->list element is freed memory, but we continue to iterate
through the list of MDIO buses using that list element.
To fix this, use the proper list iterator that handles element deletion
by keeping a copy of the list element next pointer.
Fixes: f53a2ce893 ("net: dsa: mv88e6xxx: don't use devres for mdiobus")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220210174017.3271099-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-10
Dan Carpenter propagates an error in FEC configuration.
Jesse fixes TSO offloads of IPIP and SIT frames.
Dave adds a dedicated LAG unregister function to resolve a KASAN error
and moves auxiliary device re-creation after LAG removal to the service
task to avoid issues with RTNL lock.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Avoid RTNL lock when re-creating auxiliary device
ice: Fix KASAN error in LAG NETDEV_UNREGISTER handler
ice: fix IPIP and SIT TSO offload
ice: fix an error code in ice_cfg_phy_fec()
====================
Link: https://lore.kernel.org/r/20220210170515.2609656-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An ongoing workqueue populates the stats buffer. At the same time, a user
might query the statistics. While writing to the buffer is mutex-locked,
reading from the buffer wasn't. This could lead to buggy reads by ethtool.
This patch fixes the former blamed commit, but the bug was introduced in
the latter.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Fixes: 1e1caa9735 ("ocelot: Clean up stats update deferred work")
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/all/20220210150451.416845-2-colin.foster@in-advantage.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/dsa/qca8k.c:422:37-43: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Fixes: 90386223f4 ("net: dsa: qca8k: add support for larger read/write size with mgmt Ethernet")
CC: Ansuel Smith <ansuelsmth@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209221304.GA17529@d2214a582157
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a call to re-create the auxiliary device happens in a context that has
already taken the RTNL lock, then the call flow that recreates auxiliary
device can hang if there is another attempt to claim the RTNL lock by the
auxiliary driver.
To avoid this, any call to re-create auxiliary devices that comes from
an source that is holding the RTNL lock (e.g. netdev notifier when
interface exits a bond) should execute in a separate thread. To
accomplish this, add a flag to the PF that will be evaluated in the
service task and dealt with there.
Fixes: f9f5301e7e ("ice: Register auxiliary device to provide RDMA")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the same handler is called for both a NETDEV_BONDING_INFO
LAG unlink notification as for a NETDEV_UNREGISTER call. This is
causing a problem though, since the netdev_notifier_info passed has
a different structure depending on which event is passed. The problem
manifests as a call trace from a BUG: KASAN stack-out-of-bounds error.
Fix this by creating a handler specific to NETDEV_UNREGISTER that only
is passed valid elements in the netdev_notifier_info struct for the
NETDEV_UNREGISTER event.
Also included is the removal of an unbalanced dev_put on the peer_netdev
and related braces.
Fixes: 6a8b357278 ("ice: Respond to a NETDEV_UNREGISTER event for LAG")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver was avoiding offload for IPIP (at least) frames due to
parsing the inner header offsets incorrectly when trying to check
lengths.
This length check works for VXLAN frames but fails on IPIP frames
because skb_transport_offset points to the inner header in IPIP
frames, which meant the subtraction of transport_header from
inner_network_header returns a negative value (-20).
With the code before this patch, everything continued to work, but GSO
was being used to segment, causing throughputs of 1.5Gb/s per thread.
After this patch, throughput is more like 10Gb/s per thread for IPIP
traffic.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Propagate the error code from ice_get_link_default_override() instead
of returning success.
Fixes: ea78ce4dab ("ice: add link lenient and default override support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace zero-length array with flexible-array member and make use
of the struct_size() helper in kmalloc(). For example:
struct switchdev_deferred_item {
...
unsigned long data[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 563f8e97e0 ("ipv4: Stop taking ECN bits into account in
fib4-rules") replaced the validation test on frh->tos. While the new
test is stricter for ECN bits, it doesn't detect the use of high order
DSCP bits. This would be fine if IPv4 could properly handle them. But
currently, most IPv4 lookups are done with the three high DSCP bits
masked. Therefore, using these bits doesn't lead to the expected
result.
Let's reject such configurations again, so that nobody starts to
use and make any assumption about how the stack handles the three high
order DSCP bits in fib4 rules.
Fixes: 563f8e97e0 ("ipv4: Stop taking ECN bits into account in fib4-rules")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TC feature for VFs also. When MCAM
rules are allocated for a VF then either TC or ntuple
filters can be used. Below are the commands to use
TC feature for a VF(say lbk0):
devlink dev param set pci/0002:01:00.1 name mcam_count value 16 \
cmode runtime
ethtool -K lbk0 hw-tc-offload on
ifconfig lbk0 up
tc qdisc add dev lbk0 ingress
tc filter add dev lbk0 parent ffff: protocol ip flower skip_sw \
dst_mac 98:03:9b:83:aa:12 action police rate 100Mbit burst 5000
Also to modify any fields of the hardware context with
NIX_AQ_INSTOP_WRITE command then corresponding masks of those
fields must be set as per hardware. This was missing in
ingress ratelimiting context. This patch sets those masks also.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having to acquire rtnl from netdev_run_todo() for every dismantled
device is not desirable when/if rtnl is under stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with automatic stack variable initialization, GCC 12
complains about variables defined outside of switch case statements.
Move the variable outside the switch, which silences the warning:
./net/mpls/af_mpls.c:1624:21: error: statement will never be executed [-Werror=switch-unreachable]
1624 | int err;
| ^~~
Signed-off-by: Victor Erminpour <victor.erminpour@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device firmware can assert if the device shutdown path in driver
encounters an async. events from mfw (processed in
qed_mcp_handle_events()) after qed_mcp_unload_req() returns.
A call to qed_mcp_unload_req() currently marks the device as inactive
and thus stops any new events, but there is a windows where in-flight
events might still be received by the driver.
To prevent this race condition, atomically set QED_MCP_BYPASS_PROC_BIT
in qed_mcp_unload_req() to make sure qed_mcp_handle_events() ignores all
events. Wait for any event that might already be in-process to complete
by monitoring QED_MCP_IN_PROCESSING_BIT.
Signed-off-by: Pravin Kumar Ganesh Dhende <pdhende@marvell.com>
Signed-off-by: Venkata Sudheer Kumar Bhavaraju <vbhavaraju@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev should be unregistered before we are disconnecting from the
MAC/PHY so that the dev_close callback is called and the PHY and the
phylink workqueues are actually stopped before we are disconnecting and
destroying the phylink instance.
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Single page and coherent memory blocks can use different DMA masks
when the macb accesses physical memory directly. The kernel is clever
enough to allocate pages that fit into the requested address width.
When using the ARM SMMU, the DMA mask must be the same for single
pages and big coherent memory blocks. Otherwise the translation
tables turn into one big mess.
[ 74.959909] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 74.959989] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
[ 75.173939] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 75.173955] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
Since using the same DMA mask does not hurt direct 1:1 physical
memory mappings, this commit always aligns DMA and coherent masks.
Signed-off-by: Marc St-Amand <mstamand@ciena.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net: ping6: support basic socket cmsgs
Add support for common SOL_SOCKET cmsgs in ICMPv6 sockets.
Extend the cmsg tests to cover more cmsgs and socket types.
SOL_IPV6 cmsgs to follow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test TIMESTAMPING and TXTIME across UDP / ICMP and IP versions.
Before ICMPv6 support:
# ./tools/testing/selftests/net/cmsg_time.sh
Case ICMPv6 - ts cnt returned '0', expected '2'
Case ICMPv6 - ts0 SCHED returned '', expected 'OK'
Case ICMPv6 - ts0 SND returned '', expected 'OK'
Case ICMPv6 - TXTIME abs returned '', expected 'OK'
Case ICMPv6 - TXTIME rel returned '', expected 'OK'
FAIL - 5/36 cases failed
After:
# ./tools/testing/selftests/net/cmsg_time.sh
OK
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support requesting Tx timestamps:
$ ./cmsg_sender -p i -t -4 $tgt 123 -d 1000
SCHED ts0 61us
SND ts0 1071us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test if setting SO_MARK with setsockopt works and if cmsg
takes precedence over it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
