Tegra194 has 4 SDO lines and with this configuration playback fails
for 44.1K/48K, 2-channel and 16-bps. It results in below print,
"aplay: pcm_write:2011: write error: Input/output error"
Below relation is used to derive stripe control and is referenced
from HD Audio Specification: Revision 1.0a.
{ ((num_channels * bits_per_sample) / number of SDOs) >= 8 }
Due to a legacy HW design problem, playback issue is hit while using
a stripe value resulting from above formula when ratio is '8'. Thus
it is recommended that the ratio must be greater than '8'. Since the
number of SDO lines is in powers of 2, next available ratio '16' is
used as a limiting factor on Tegra194 to workaround the problem.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1588580176-2801-4-git-send-email-spujar@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra194 supports 4 SDO lines but GCAP register indicates 2 lines. Thus it
does not reflect the true capability of the HW. This patch presents a
workaround by updating NSDO value accordingly in T_AZA_DBG_CFG_2 register.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1588580176-2801-2-git-send-email-spujar@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that the recent simplification of HD-audio bus access
helpers caused a regression on the virtual HD-audio device on QEMU
with ARM platforms. The driver got a CORB/RIRB timeout and couldn't
probe any codecs.
The essential difference that caused a problem was the enforced
aligned MMIO accesses by simplification. Since snd-hda-tegra driver
is enabled on ARM, it enables CONFIG_SND_HDA_ALIGNED_MMIO, which makes
the all HD-audio drivers using the aligned MMIO accesses. While this
is mandatory for snd-hda-tegra, it seems that snd-hda-intel on ARM
gets broken by this access pattern.
For addressing the regression, this patch introduces a new flag,
aligned_mmio, to hdac_bus object, and applies the aligned MMIO only
when this flag is set. This change affects only platforms with
CONFIG_SND_HDA_ALIGNED_MMIO set, i.e. mostly only for ARM platforms.
Unfortunately the patch became a big bigger than it should be, just
because the former calls didn't take hdac_bus object in the argument,
hence we had to extend the call patterns.
Fixes: 19abfefd4c ("ALSA: hda: Direct MMIO accesses")
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1161152
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200120104127.28985-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we may declare const for snd_device_ops definitions, so let's do
it for optimization.
There should be no functional changes by this patch.
Link: https://lore.kernel.org/r/20200103081714.9560-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now most of the get_response handling became quite similar between
HDA-core and legacy drivers, and the only differences are:
- the handling of extra-long polling delay for some codecs
- the debug message for the stalled communication
and both are worth to share in the common code.
This patch unifies the code into snd_hdac_bus_get_response(), and use
this from the legacy get_response callback. It results in a good
amount of code reduction in the end.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20191212191101.19517-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Forgot to remove the variable declaration as well in the last commit.
sound/pci/hda/hda_tegra.c: In function 'hda_tegra_runtime_suspend':
sound/pci/hda/hda_tegra.c:169:19: warning: unused variable 'bus' [-Wunused-variable]
Fixes: f36da9406e ("ALSA: hda: Support PCM sync_stop")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20191212080518.6522-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver invokes snd_pcm_period_elapsed() simply from the interrupt
handler. Set card->sync_irq for enabling the missing sync_stop PCM
operation. It's cleared and reset dynamically at IRQ re-acquiring for
the PM resume, too.
Link: https://lore.kernel.org/r/20191210063454.31603-22-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio drivers access to the mmio registers indirectly via the
corresponding bus->io_ops callbacks. This is because some platform
(notably Tegra SoC) requires the word-aligned access. But it's rather
a rare case, and other platforms suffer from the penalties by indirect
calls unnecessarily.
This patch is an attempt to optimize and cleanup for this situation.
Now the special aligned access is used only when a new kconfig
CONFIG_SND_HDA_ALIGNED_MMIO is set. And the HD-audio core itself
provides the aligned MMIO access helpers instead of the driver side.
If Kconfig isn't set (as default), the standard helpers like readl()
or writel() are used directly.
A couple of places in ASoC Intel drivers have the access via io_ops
reg_writel(), and they are replaced with the direct writel() calls.
And now with this patch, the whole bus->io_ops becomes empty, so it's
dropped completely. The bus initialization functions are changed
accordingly as well to drop the whole bus->io_ops.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio core allocates and releases pages via driver's specific
dma_alloc_pages and dma_free_pages ops defined in bus->io_ops. This
was because some platforms require the uncached pages and the handling
of page flags had to be done locally in the driver code.
Since the recent change in ALSA core memory allocator, we can simply
pass SNDRV_DMA_TYPE_DEV_UC for the uncached pages, and the only
difference became about this type to be passed to the core allocator.
That is, it's good time for cleaning up the mess.
This patch changes the allocation code in HD-audio core to call the
core allocator directly so that we get rid of dma_alloc_pages and
dma_free_pages io_ops. If a driver needs the uncached pages, it has
to set bus->dma_type right after the bus initialization.
This is merely a code refactoring and shouldn't bring any behavior
changes.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef protection around the PM functions is wrong, leading to
a failed reference in some configurations:
sound/pci/hda/hda_tegra.c: In function 'hda_tegra_runtime_suspend':
sound/pci/hda/hda_tegra.c:273:2: error: implicit declaration of function 'hda_tegra_disable_clocks'; did you mean 'hda_tegra_enable_clocks'? [-Werror=implicit-function-declaration]
Better remove the #ifdefs entirely and rely on the compiler silently
dropping unused functions marked __maybe_unused.
Fixes: 707e0759f2 ("ALSA: hda/tegra: implement runtime suspend/resume")
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A platform can have multiple sound cards for different audio paths.
Following is the print seen duirng device boot for jetson-xavier,
ALSA device list:
#0: nvidia,p2972-0000 at 0x3518000 irq 17
By looking at above, it is not very clear if the sound card is for
HDA. It becomes confusing when platform has registered multiple cards,
and platform model name is used for card.
This patch uses "nvidia,model" property mentioned in hda device tree
to get the card name. Since property is optional, legacy boards will
continue to use "tegra-hda". Custom name can be passed wherever needed.
This naming convention is conistent with the way sound cards are named
in general.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AZX_DCAPS_PM_RUNTIME flag is added to indicate support for runtime PM.
azx_has_pm_runtime() is used to check if above is enabled and thus
forbid runtime PM calls if needed.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Ravindra Lokhande <rlokhande@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch moves clock enable/disable from system resume/suspend to
runtime resume/suspend respectively. Along with this hda controller
chip init or stop is also moved. System resume/suspend can invoke
runtime callbacks and do necessary setup.
chip->running can be used to check for probe completion and device
access during runtime_resume or runtime_suspend can be avoided if
probe is not yet finished. This helps to avoid kernel panic during
boot where runtime PM callbacks can happen from system PM.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Ravindra Lokhande <rlokhande@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Explicit clock enable is not required during probe, as this would be
managed by runtime PM calls. Clock can be enabled/disabled in runtime
resume/suspend. This way it is easier to balance clock enable/disable
counts.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Ravindra Lokhande <rlokhande@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Moved devm_clk_get() API calls to a separate function and the same
can be called early in the probe. This is done before runtime PM
for the device is enabled. The runtime resume/suspend callbacks can
later enable/disable clocks respectively(the support would be added
in subsequent patches). Clock handles should be available by the
time runtime suspend/resume calls can happen.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Ravindra Lokhande <rlokhande@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables runtime power management(runtime PM) support for
hda. pm_runtime_enable() and pm_runtime_disable() are added during
device probe and remove respectively. The runtime PM callbacks will
be forbidden if hda controller does not have support for runtime PM.
pm_runtime_get_sync() and pm_runtime_put() are added for hda register
access. The callbacks for above will be added in subsequent patches.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Ravindra Lokhande <rlokhande@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Even after disabling interrupts on the module, it could be possible
that irq handlers are still running. System hang is seen during
suspend path. It was found that, there were pending writes on the
HDA bus and clock was disabled by that time.
Above mentioned issue is fixed by clearing any pending irq handlers
before disabling clocks and returning from hda suspend.
Suggested-by: Mohan Kumar <mkumard@nvidia.com>
Suggested-by: Dara Ramesh <dramesh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent devices support more than the 4 codecs that the AZX core will
probe by default. Probe up to 8 codecs to make sure all of them are
enumerated.
Suggested-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By default HDA sound card is registered with shortname "tegra-hda".
Same driver is used across tegra platforms and it is necessary to
distinguish between platforms to use platform specific settings from
userspace. One such example is, hdmi port on different platforms use
different alsa pcm device ID. For hdmi playback to work it should
open correct pcm device depending on the platform.
This patch applies shortname from first compatible string provided
in root node of device tree. Userspace then can use this card name
to apply specific settings.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For easier sharing with ASoC.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluIAxkTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NVNB/0cE/j09cyBR80x5gvnFE3Z5NEPNPLP
yl7sD93xFP6iww3CGJjXgxxDTh2sf7Sro4hcR9ZdD9zSSQ1qMVVY28MJ1YUsbFPu
TeUkqRFNPjgOpSmwK7T5QpVbIvdTZmmht8umgQ2+Y4vsGu1aKZf80ZT2n/2mjTOe
bEYfpyjP5V1aVL8JcX4TN3hbGZ2Pth5m404Qe0pkIdv4qqLx2edphJQ7ecU8w3kK
vTg1gfo7j9CKx7rzHZei/cvA3qXl/g9oufHAfpJDrlYFz6N35qwpA5UCyXqcFVo2
kZtyFbaBAvBjnhVyMNkdG7PvBMlL6HMLxN3fJbMLPPS30/+IuAsHXkZY
=wtBB
-----END PGP SIGNATURE-----
Merge tag 'hda-codec-h-move' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ALSA: Move hda_codec.h to include/sound
For easier sharing with ASoC.
As suggested by Takashi, move this header file to make it easier
to include from e.g. the Intel Skylake driver in follow-up patches
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we dropped the memory page fiddling in the own allocators in
hda_intel.c, the substream allocation and free ops in both hda_intel.c
and hda_tegra.c became nothing but the simple calls of the standard
snd_pcm_lib helpers. As both are identical, there is no longer need
for indirect calls via ops; it's a good opportunity for removing ops
and simplifying the codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AZX_DCAPS_RIRB_DELAY is dedicated only for Nvidia and its purpose is
just to set a flag in bus. So it's better to be set in the toplevel
driver, either hda_intel.c or hda_tegra.c, instead of the common
hda_controller.c. This also allows us to strip this flag from dcaps,
so save one more bit there.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Tegra HD-audio controller driver causes deadlocks when loaded as a
module since the driver invokes request_module() at binding with the
codec driver. This patch works around it by deferring the probe in a
work like Intel HD-audio controller driver does. Although hovering
the codec probe stuff into udev would be a better solution, it may
cause other regressions, so let's try this band-aid fix until the more
proper solution gets landed.
Reported-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When probing, provide accurate error messages to help with debugging
failures.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is set for the MCP variants of the NVIDIA HDA controller, which the
Tegra variant was derived from. This fixes the following warning at boot
time:
[ 2.486610] tegra-hda 70030000.hda: CORB reset timeout#1, CORBRP = 0
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I seem to have failed to run the build test properly...
sound/pci/hda/hda_tegra.c: In function 'hda_tegra_dev_free':
sound/pci/hda/hda_tegra.c:310:20: error: 'bus' undeclared (first use in this function)
snd_hdac_bus_exit(bus);
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and replace with the existing hda-core helper codes.
This reduces lots of lines, finally.
Since struct hda_bus is now embedded into struct azx,
snd_hda_bus_new() is moved and expanded from hda_codec.c to
hda_controller.c, accordingly. Also private_free bus ops and
private_data field are removed because we no longer need to point azx
object from bus (we can use container_of())
The spin locks are consolidated into the single one, bus->reg_lock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Embed hdac_stream object into azx_dev, and use a few basic helper
functions. The most of helper codes for hdac_stream aren't still used
yet.
Also this commit disables the tracepoints temporarily due to build
problems. It'll be enabled again later.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One less redirection again. This also requires the change of the call
order in the toplevel divers. Namely, the bus has to be created at
first before other initializations since the memory allocation ops are
called through bus object now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver shutdown ops is simpler than registering reboot notifier
manually. There should be no functional change by this -- the codec
driver calls its own callback while the bus driver just calls
azx_stop() like before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes the code flow easier -- instead of the controller driver
calling snd_hda_build_pcms() and snd_hda_build_controls() explicitly,
the codec driver itself builds PCMs and controls at probe time. Then
the controller driver only needs to call snd_card_register().
Also, this allows us the full bind/unbind control, too. Even when a
codec driver is bound later, it automatically registers the new PCM
and controls by itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, we let the controller driver power down the all codecs at the
end of probe. But this can be done better in the codec's dev_register
callback. This results in the reduction of duplicated codes in each
control driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We used to pass the power_save option value to hda_bus via a given
pointer. This was needed to refer to the value from the HD-audio core
side. However, after the transition to the runtime PM, this is no
longer needed.
This patch drops the power_save value indirection in hda_bus above,
and let the controller driver reprograms the autosuspend value
explicitly by a new helper, snd_hda_set_power_save(). Without this
call, the HD-audio core doesn't set up the autosuspend and flip the
runtime PM. (User may still be able to set up via sysfs, though.)
Along with this change, the pointer argument of azx_bus_create() is
dropped as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch moves the suspend/resume mechanisms down to each codec
driver level, as we have a proper codec driver bound on the bus now.
Then we get the asynchronous PM gratis without fiddling much in the
driver level.
As a soft-landing transition, implement the common suspend/resume pm
ops for hda_codec_driver and keep the each codec driver intact. Only
the callers of suspend/resume in the controller side (azx_suspend()
and azx_resume()) are removed.
Another involved place is azx_bus_reset() calling the temporary
suspend and resume as a hackish method of bus reset. The HD-audio
core provide a helper function snd_hda_bus_reset() instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
azx_create_codec() function does actually two things: create a bus and
probe codecs. For the future work, split this to two logical
functions, azx_bus_create() and azx_probe_codecs().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since init_failed flag was moved to struct hda_intel, its access in
the commit [4da63c6f: ALSA: hda - Fix broken PM due to incomplete
i915 initialization] is also replaced with hda->init_failed
appropriately.
The hda_tegra_disable_clocks() function is only used by the suspend and
resume code, so it needs to be included in the #ifdef CONFIG_PM_SLEEP
block to prevent the following warning:
CC sound/pci/hda/hda_tegra.o
sound/pci/hda/hda_tegra.c:238:13: warning: 'hda_tegra_disable_clocks' defined but not used [-Wunused-function]
static void hda_tegra_disable_clocks(struct hda_tegra *data)
^
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'status' is not used in the function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Tested-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "list" field has been omitted from struct azx, but its
initialization remained mistakenly in hda_tegra.c, which leads to a
compile error:
sound/pci/hda/hda_tegra.c: In function 'hda_tegra_create':
sound/pci/hda/hda_tegra.c:481:22: error: 'struct azx' has no member
named 'list'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 9a34af4a33 ('ALSA: hda - Move more PCI-controller-specific stuff from generic code')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
