When the conntracking code multiplies a timeout by HZ, it can overflow
from positive to negative; this causes it to instantly expire. To
protect against this the multiplication is done in 64-bit so we can
prevent it from exceeding INT_MAX.
Signed-off-by: Jay Elliott <jelliott@arista.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When zero window is announced we can get into a situation where
connection stays around forever:
1. One side announces zero window.
2. Other side closes.
In this case, no FIN is sent (stuck in send queue).
Unless other side opens the window up again conntrack
stays in ESTABLISHED state for a very long time.
Lets alleviate this by lowering the timeout to RETRANS (5 minutes),
the other end should be sending zero window probes to keep the
connection established as long as a socket still exists.
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch fixes several out of bounds memory reads by extending
the nf_h323_error_boundary() function to work on bits as well
an check the affected parts.
Signed-off-by: Eric Sesterhenn <eric.sesterhenn@x41-dsec.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It is bad practive to return in a macro, this patch
moves the check into a function.
Signed-off-by: Eric Sesterhenn <eric.sesterhenn@x41-dsec.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Be sure that lists initialized in net_init hook was return to initial
state.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The assignment to variable e is redundant since the same assignment
occurs just a few lines later, hence it can be removed. Cleans up
clang warning for arp_tables, ip_tables and ip6_tables:
warning: Value stored to 'e' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix the TLP scheduling logic so that when scheduling a TLP probe, we
ensure that the estimated time at which an RTO would fire accounts for
the fact that ACKs indicating forward progress should push back RTO
times.
After the following fix:
df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
we had an unintentional behavior change in the following kind of
scenario: suppose the RTT variance has been very low recently. Then
suppose we send out a flight of N packets and our RTT is 100ms:
t=0: send a flight of N packets
t=100ms: receive an ACK for N-1 packets
The response before df92c8394e that was:
-> schedule a TLP for now + RTO_interval
The response after df92c8394e is:
-> schedule a TLP for t=0 + RTO_interval
Since RTO_interval = srtt + RTT_variance, this means that we have
scheduled a TLP timer at a point in the future that only accounts for
RTT_variance. If the RTT_variance term is small, this means that the
timer fires soon.
Before df92c8394e this would not happen, because in that code, when
we receive an ACK for a prefix of flight, we did:
1) Near the top of tcp_ack(), switch from TLP timer to RTO
at write_queue_head->paket_tx_time + RTO_interval:
if (icsk->icsk_pending == ICSK_TIME_LOSS_PROBE)
tcp_rearm_rto(sk);
2) In tcp_clean_rtx_queue(), update the RTO to now + RTO_interval:
if (flag & FLAG_ACKED) {
tcp_rearm_rto(sk);
3) In tcp_ack() after tcp_fastretrans_alert() switch from RTO
to TLP at now + RTO_interval:
if (icsk->icsk_pending == ICSK_TIME_RETRANS)
tcp_schedule_loss_probe(sk);
In df92c8394e we removed that 3-phase dance, and instead directly
set the TLP timer once: we set the TLP timer in cases like this to
write_queue_head->packet_tx_time + RTO_interval. So if the RTT
variance is small, then this means that this is setting the TLP timer
to fire quite soon. This means if the ACK for the tail of the flight
takes longer than an RTT to arrive (often due to delayed ACKs), then
the TLP timer fires too quickly.
Fixes: df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 308edfdf15 ("gre6: Cleanup GREv6 receive path, call
common GRE functions") it's not used anywhere in the module, but
previously was used in ip6gre_rcv().
Fixes: 308edfdf15 ("gre6: Cleanup GREv6 receive path, call common GRE functions")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Revert regression inducing change to the IPSEC template resolver,
from Steffen Klassert.
2) Peeloffs can cause the wrong sk to be waken up in SCTP, fix from Xin
Long.
3) Min packet MTU size is wrong in cpsw driver, from Grygorii Strashko.
4) Fix build failure in netfilter ctnetlink, from Arnd Bergmann.
5) ISDN hisax driver checks pnp_irq() for errors incorrectly, from
Arvind Yadav.
6) Fix fealnx driver build failure on MIPS, from Huacai Chen.
7) Fix into leak in SCTP, the scope_id of socket addresses is not
always filled in. From Eric W. Biederman.
8) MTU inheritance between physical function and representor fix in nfp
driver, from Dirk van der Merwe.
9) Fix memory leak in rsi driver, from Colin Ian King.
10) Fix expiration and generation ID handling of cached ipv4 redirect
routes, from Xin Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net: usb: hso.c: remove unneeded DRIVER_LICENSE #define
ibmvnic: fix dma_mapping_error call
ipvlan: NULL pointer dereference panic in ipvlan_port_destroy
route: also update fnhe_genid when updating a route cache
route: update fnhe_expires for redirect when the fnhe exists
sctp: set frag_point in sctp_setsockopt_maxseg correctly
rsi: fix memory leak on buf and usb_reg_buf
net/netlabel: Add list_next_rcu() in rcu_dereference().
nfp: remove false positive offloads in flower vxlan
nfp: register flower reprs for egress dev offload
nfp: inherit the max_mtu from the PF netdev
nfp: fix vlan receive MAC statistics typo
nfp: fix flower offload metadata flag usage
virto_net: remove empty file 'virtio_net.'
net/sctp: Always set scope_id in sctp_inet6_skb_msgname
fealnx: Fix building error on MIPS
isdn: hisax: Fix pnp_irq's error checking for setup_teles3
isdn: hisax: Fix pnp_irq's error checking for setup_sedlbauer_isapnp
isdn: hisax: Fix pnp_irq's error checking for setup_niccy
isdn: hisax: Fix pnp_irq's error checking for setup_ix1micro
...
Now when ip route flush cache and it turn out all fnhe_genid != genid.
If a redirect/pmtu icmp packet comes and the old fnhe is found and all
it's members but fnhe_genid will be updated.
Then next time when it looks up route and tries to rebind this fnhe to
the new dst, the fnhe will be flushed due to fnhe_genid != genid. It
causes this redirect/pmtu icmp packet acutally not to be applied.
This patch is to also reset fnhe_genid when updating a route cache.
Fixes: 5aad1de5ea ("ipv4: use separate genid for next hop exceptions")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when creating fnhe for redirect, it sets fnhe_expires for this
new route cache. But when updating the exist one, it doesn't do it.
It will cause this fnhe never to be expired.
Paolo already noticed it before, in Jianlin's test case, it became
even worse:
When ip route flush cache, the old fnhe is not to be removed, but
only clean it's members. When redirect comes again, this fnhe will
be found and updated, but never be expired due to fnhe_expires not
being set.
So fix it by simply updating fnhe_expires even it's for redirect.
Fixes: aee06da672 ("ipv4: use seqlock for nh_exceptions")
Reported-by: Jianlin Shi <jishi@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_setsockopt_maxseg user_frag or frag_point can be set with
val >= 8 and val <= SCTP_MAX_CHUNK_LEN. But both checks are incorrect.
val >= 8 means frag_point can even be less than SCTP_DEFAULT_MINSEGMENT.
Then in sctp_datamsg_from_user(), when it's value is greater than cookie
echo len and trying to bundle with cookie echo chunk, the first_len will
overflow.
The worse case is when it's value is equal as cookie echo len, first_len
becomes 0, it will go into a dead loop for fragment later on. In Hangbin
syzkaller testing env, oom was even triggered due to consecutive memory
allocation in that loop.
Besides, SCTP_MAX_CHUNK_LEN is the max size of the whole chunk, it should
deduct the data header for frag_point or user_frag check.
This patch does a proper check with SCTP_DEFAULT_MINSEGMENT subtracting
the sctphdr and datahdr, SCTP_MAX_CHUNK_LEN subtracting datahdr when
setting frag_point via sockopt. It also improves sctp_setsockopt_maxseg
codes.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add list_next_rcu() for fetching next list in rcu_deference safely.
Found with sparse in linux-next tree on tag next-20171116.
Signed-off-by: Tim Hansen <devtimhansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable bugfixes:
- Revalidate "." and ".." correctly on open
- Avoid RCU usage in tracepoints
- Fix ugly referral attributes
- Fix a typo in nomigration mount option
- Revert "NFS: Move the flock open mode check into nfs_flock()"
Features:
- Implement a stronger send queue accounting system for NFS over RDMA
- Switch some atomics to the new refcount_t type
Other bugfixes and cleanups:
- Clean up access mode bits
- Remove special-case revalidations in nfs_opendir()
- Improve invalidating NFS over RDMA memory for async operations that time out
- Handle NFS over RDMA replies with a worqueue
- Handle NFS over RDMA sends with a workqueue
- Fix up replaying interrupted requests
- Remove dead NFS over RDMA definitions
- Update NFS over RDMA copyright information
- Be more consistent with bool initialization and comparisons
- Mark expected switch fall throughs
- Various sunrpc tracepoint cleanups
- Fix various OPEN races
- Fix a typo in nfs_rename()
- Use common error handling code in nfs_lock_and_join_request()
- Check that some structures are properly cleaned up during net_exit()
- Remove net pointer from dprintk()s
-----BEGIN PGP SIGNATURE-----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=2Zc1
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.15-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client updates from Anna Schumaker:
"Stable bugfixes:
- Revalidate "." and ".." correctly on open
- Avoid RCU usage in tracepoints
- Fix ugly referral attributes
- Fix a typo in nomigration mount option
- Revert "NFS: Move the flock open mode check into nfs_flock()"
Features:
- Implement a stronger send queue accounting system for NFS over RDMA
- Switch some atomics to the new refcount_t type
Other bugfixes and cleanups:
- Clean up access mode bits
- Remove special-case revalidations in nfs_opendir()
- Improve invalidating NFS over RDMA memory for async operations that
time out
- Handle NFS over RDMA replies with a worqueue
- Handle NFS over RDMA sends with a workqueue
- Fix up replaying interrupted requests
- Remove dead NFS over RDMA definitions
- Update NFS over RDMA copyright information
- Be more consistent with bool initialization and comparisons
- Mark expected switch fall throughs
- Various sunrpc tracepoint cleanups
- Fix various OPEN races
- Fix a typo in nfs_rename()
- Use common error handling code in nfs_lock_and_join_request()
- Check that some structures are properly cleaned up during
net_exit()
- Remove net pointer from dprintk()s"
* tag 'nfs-for-4.15-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (62 commits)
NFS: Revert "NFS: Move the flock open mode check into nfs_flock()"
NFS: Fix typo in nomigration mount option
nfs: Fix ugly referral attributes
NFS: super: mark expected switch fall-throughs
sunrpc: remove net pointer from messages
nfs: remove net pointer from messages
sunrpc: exit_net cleanup check added
nfs client: exit_net cleanup check added
nfs/write: Use common error handling code in nfs_lock_and_join_requests()
NFSv4: Replace closed stateids with the "invalid special stateid"
NFSv4: nfs_set_open_stateid must not trigger state recovery for closed state
NFSv4: Check the open stateid when searching for expired state
NFSv4: Clean up nfs4_delegreturn_done
NFSv4: cleanup nfs4_close_done
NFSv4: Retry NFS4ERR_OLD_STATEID errors in layoutreturn
pNFS: Retry NFS4ERR_OLD_STATEID errors in layoutreturn-on-close
NFSv4: Don't try to CLOSE if the stateid 'other' field has changed
NFSv4: Retry CLOSE and DELEGRETURN on NFS4ERR_OLD_STATEID.
NFS: Fix a typo in nfs_rename()
NFSv4: Fix open create exclusive when the server reboots
...
Publishing of net pointer is not safe, use net->ns.inum as net ID
[ 171.391947] RPC: created new rpcb local clients
(rpcb_local_clnt: ..., rpcb_local_clnt4: ...) for net f00001e7
[ 171.767188] NFSD: starting 90-second grace period (net f00001e7)
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Be sure that all_clients list initialized in net_init hook was return
to initial state.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Display information about the RPC procedure being requested in the
trace log. This sometimes critical information cannot always be
derived from other RPC trace entries.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The rpc_task_begin trace point always display a task ID of zero.
Move the trace point call site so that it picks up the new task ID.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Credit work contributed by Oracle engineers since 2014.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up. This include should have been removed by
commit 23826c7aea ("xprtrdma: Serialize credit accounting again").
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: C-structure style XDR encoding and decoding logic has
been replaced over the past several merge windows on both the
client and server. These data structures are no longer used.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Lift the Send and LocalInv completion handlers out of soft IRQ mode
to make room for other work. Also, move the Send CQ to a different
CPU than the CPU where the Receive CQ is running, for improved
scalability.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Pull get_user_pages_fast() conversion from Al Viro:
"A bunch of places switched to get_user_pages_fast()"
* 'work.get_user_pages_fast' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ceph: use get_user_pages_fast()
pvr2fs: use get_user_pages_fast()
atomisp: use get_user_pages_fast()
st: use get_user_pages_fast()
via_dmablit(): use get_user_pages_fast()
fsl_hypervisor: switch to get_user_pages_fast()
rapidio: switch to get_user_pages_fast()
vchiq_2835_arm: switch to get_user_pages_fast()
The sendctx circular queue now guarantees that xprtrdma cannot
overflow the Send Queue, so remove the remaining bits of the
original Send WQE counting mechanism.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When an RPC Call includes a file data payload, that payload can come
from pages in the page cache, or a user buffer (for direct I/O).
If the payload can fit inline, xprtrdma includes it in the Send
using a scatter-gather technique. xprtrdma mustn't allow the RPC
consumer to re-use the memory where that payload resides before the
Send completes. Otherwise, the new contents of that memory would be
exposed by an HCA retransmit of the Send operation.
So, block RPC completion on Send completion, but only in the case
where a separate file data payload is part of the Send. This
prevents the reuse of that memory while it is still part of a Send
operation without an undue cost to other cases.
Waiting is avoided in the common case because typically the Send
will have completed long before the RPC Reply arrives.
These days, an RPC timeout will trigger a disconnect, which tears
down the QP. The disconnect flushes all waiting Sends. This bounds
the amount of time the reply handler has to wait for a Send
completion.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Invoke a common routine for releasing hardware resources (for
example, invalidating MRs). This needs to be done whether an
RPC Reply has arrived or the RPC was terminated early.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
We have one boolean flag in rpcrdma_req today. I'd like to add more
flags, so convert that boolean to a bit flag.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Problem statement:
Recently Sagi Grimberg <sagi@grimberg.me> observed that kernel RDMA-
enabled storage initiators don't handle delayed Send completion
correctly. If Send completion is delayed beyond the end of a ULP
transaction, the ULP may release resources that are still being used
by the HCA to complete a long-running Send operation.
This is a common design trait amongst our initiators. Most Send
operations are faster than the ULP transaction they are part of.
Waiting for a completion for these is typically unnecessary.
Infrequently, a network partition or some other problem crops up
where an ordering problem can occur. In NFS parlance, the RPC Reply
arrives and completes the RPC, but the HCA is still retrying the
Send WR that conveyed the RPC Call. In this case, the HCA can try
to use memory that has been invalidated or DMA unmapped, and the
connection is lost. If that memory has been re-used for something
else (possibly not related to NFS), and the Send retransmission
exposes that data on the wire.
Thus we cannot assume that it is safe to release Send-related
resources just because a ULP reply has arrived.
After some analysis, we have determined that the completion
housekeeping will not be difficult for xprtrdma:
- Inline Send buffers are registered via the local DMA key, and
are already left DMA mapped for the lifetime of a transport
connection, thus no additional handling is necessary for those
- Gathered Sends involving page cache pages _will_ need to
DMA unmap those pages after the Send completes. But like
inline send buffers, they are registered via the local DMA key,
and thus will not need to be invalidated
In addition, RPC completion will need to wait for Send completion
in the latter case. However, nearly always, the Send that conveys
the RPC Call will have completed long before the RPC Reply
arrives, and thus no additional latency will be accrued.
Design notes:
In this patch, the rpcrdma_sendctx object is introduced, and a
lock-free circular queue is added to manage a set of them per
transport.
The RPC client's send path already prevents sending more than one
RPC Call at the same time. This allows us to treat the consumer
side of the queue (rpcrdma_sendctx_get_locked) as if there is a
single consumer thread.
The producer side of the queue (rpcrdma_sendctx_put_locked) is
invoked only from the Send completion handler, which is a single
thread of execution (soft IRQ).
The only care that needs to be taken is with the tail index, which
is shared between the producer and consumer. Only the producer
updates the tail index. The consumer compares the head with the
tail to ensure that the a sendctx that is in use is never handed
out again (or, expressed more conventionally, the queue is empty).
When the sendctx queue empties completely, there are enough Sends
outstanding that posting more Send operations can result in a Send
Queue overflow. In this case, the ULP is told to wait and try again.
This introduces strong Send Queue accounting to xprtrdma.
As a final touch, Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
suggested a mechanism that does not require signaling every Send.
We signal once every N Sends, and perform SGE unmapping of N Send
operations during that one completion.
Reported-by: Sagi Grimberg <sagi@grimberg.me>
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Commit 655fec6987 ("xprtrdma: Use gathered Send for large inline
messages") assumed that, since the zeroeth element of the Send SGE
array always pointed to req->rl_rdmabuf, it needed to be initialized
just once. This was a valid assumption because the Send SGE array
and rl_rdmabuf both live in the same rpcrdma_req.
In a subsequent patch, the Send SGE array will be separated from the
rpcrdma_req, so the zeroeth element of the SGE array needs to be
initialized every time.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Make rpcrdma_prepare_send_sges() return a negative errno
instead of a bool. Soon callers will want distinct treatments of
different types of failures.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When this function fails, it needs to undo the DMA mappings it's
done so far. Otherwise these are leaked.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up. rpcrdma_prepare_hdr_sge() sets num_sge to one, then
rpcrdma_prepare_msg_sges() sets num_sge again to the count of SGEs
it added, plus one for the header SGE just mapped in
rpcrdma_prepare_hdr_sge(). This is confusing, and nails in an
assumption about when these functions are called.
Instead, maintain a running count that both functions can update
with just the number of SGEs they have added to the SGE array.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
We need to decode and save the incoming rdma_credits field _after_
we know that the direction of the message is "forward direction
Reply". Otherwise, the credits value in reverse direction Calls is
also used to update the forward direction credits.
It is safe to decode the rdma_credits field in rpcrdma_reply_handler
now that rpcrdma_reply_handler is single-threaded. Receives complete
in the same order as they were sent on the NFS server.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I noticed that the soft IRQ thread looked pretty busy under heavy
I/O workloads. perf suggested one area that was expensive was the
queue_work() call in rpcrdma_wc_receive. That gave me some ideas.
Instead of scheduling a separate worker to process RPC Replies,
promote the Receive completion handler to IB_POLL_WORKQUEUE, and
invoke rpcrdma_reply_handler directly.
Note that the poll workqueue is single-threaded. In order to keep
memory invalidation from serializing all RPC Replies, handle any
necessary invalidation tasks in a separate multi-threaded workqueue.
This provides a two-tier scheme, similar to OS I/O interrupt
handlers: A fast interrupt handler that schedules the slow handler
and re-enables the interrupt, and a slower handler that is invoked
for any needed heavy lifting.
Benefits include:
- One less context switch for RPCs that don't register memory
- Receive completion handling is moved out of soft IRQ context to
make room for other users of soft IRQ
- The same CPU core now DMA syncs and XDR decodes the Receive buffer
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: I'd like to be able to invoke the tail of
rpcrdma_reply_handler in two different places. Split the tail out
into its own helper function.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Make it easier to pass the decoded XID, vers, credits, and
proc fields around by moving these variables into struct rpcrdma_rep.
Note: the credits field will be handled in a subsequent patch.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
A reply with an unrecognized value in the version field means the
transport header is potentially garbled and therefore all the fields
are untrustworthy.
Fixes: 59aa1f9a3c ("xprtrdma: Properly handle RDMA_ERROR ... ")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Alexandar Potapenko while testing the kernel with KMSAN and syzkaller
discovered that in some configurations sctp would leak 4 bytes of
kernel stack.
Working with his reproducer I discovered that those 4 bytes that
are leaked is the scope id of an ipv6 address returned by recvmsg.
With a little code inspection and a shrewd guess I discovered that
sctp_inet6_skb_msgname only initializes the scope_id field for link
local ipv6 addresses to the interface index the link local address
pertains to instead of initializing the scope_id field for all ipv6
addresses.
That is almost reasonable as scope_id's are meaniningful only for link
local addresses. Set the scope_id in all other cases to 0 which is
not a valid interface index to make it clear there is nothing useful
in the scope_id field.
There should be no danger of breaking userspace as the stack leak
guaranteed that previously meaningless random data was being returned.
Fixes: 372f525b495c ("SCTP: Resync with LKSCTP tree.")
History-tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Copy policy family in clone_policy, otherwise this can
trigger a BUG_ON in af_key. From Herbert Xu.
2) Revert "xfrm: Fix stack-out-of-bounds read in xfrm_state_find."
This added a regression with transport mode when no addresses
are configured on the policy template.
Both patches are stable candidates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2 updates
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
memory hotplug: fix comments when adding section
mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
mm: simplify nodemask printing
mm,oom_reaper: remove pointless kthread_run() error check
mm/page_ext.c: check if page_ext is not prepared
writeback: remove unused function parameter
mm: do not rely on preempt_count in print_vma_addr
mm, sparse: do not swamp log with huge vmemmap allocation failures
mm/hmm: remove redundant variable align_end
mm/list_lru.c: mark expected switch fall-through
mm/shmem.c: mark expected switch fall-through
mm/page_alloc.c: broken deferred calculation
mm: don't warn about allocations which stall for too long
fs: fuse: account fuse_inode slab memory as reclaimable
mm, page_alloc: fix potential false positive in __zone_watermark_ok
mm: mlock: remove lru_add_drain_all()
mm, sysctl: make NUMA stats configurable
shmem: convert shmem_init_inodecache() to void
Unify migrate_pages and move_pages access checks
mm, pagevec: rename pagevec drained field
...
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of. Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact. Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.
This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache. Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop. It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.
The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path. A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.
Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "kmemcheck: kill kmemcheck", v2.
As discussed at LSF/MM, kill kmemcheck.
KASan is a replacement that is able to work without the limitation of
kmemcheck (single CPU, slow). KASan is already upstream.
We are also not aware of any users of kmemcheck (or users who don't
consider KASan as a suitable replacement).
The only objection was that since KASAN wasn't supported by all GCC
versions provided by distros at that time we should hold off for 2
years, and try again.
Now that 2 years have passed, and all distros provide gcc that supports
KASAN, kill kmemcheck again for the very same reasons.
This patch (of 4):
Remove kmemcheck annotations, and calls to kmemcheck from the kernel.
[alexander.levin@verizon.com: correctly remove kmemcheck call from dma_map_sg_attrs]
Link: http://lkml.kernel.org/r/20171012192151.26531-1-alexander.levin@verizon.com
Link: http://lkml.kernel.org/r/20171007030159.22241-2-alexander.levin@verizon.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tim Hansen <devtimhansen@gmail.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have a NUMA-aware version of kmalloc_array() we can use it
instead of kmalloc_node() without an overflow check in the size
calculation.
Link: http://lkml.kernel.org/r/20170927082038.3782-7-jthumshirn@suse.de
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Lameter <cl@linux.com>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mike Marciniszyn <infinipath@intel.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The socket level flow control is based on the assumption that incoming
buffers meet the condition (skb->truesize / roundup(skb->len) <= 4),
where the latter value is rounded off upwards to the nearest 1k number.
This does empirically hold true for the device drivers we know, but we
cannot trust that it will always be so, e.g., in a system with jumbo
frames and very small packets.
We now introduce a check for this condition at packet arrival, and if
we find it to be false, we copy the packet to a new, smaller buffer,
where the condition will be true. We expect this to affect only a small
fraction of all incoming packets, if at all.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is no longer marked 'inline', so we now get a warning
when it is unused:
net/netfilter/nf_conntrack_netlink.c:536:15: error: 'ctnetlink_proto_size' defined but not used [-Werror=unused-function]
We could mark it inline again, mark it __maybe_unused, or add an #ifdef
around the definition. I'm picking the third approach here since that
seems to be what the rest of the file has.
Fixes: 5caaed151a ("netfilter: conntrack: don't cache nlattr_tuple_size result in nla_size")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the description, first argument of genlmsg_nlhdr() points to
what genlmsg_put() returns, i.e. beginning of user header. Therefore we
should only subtract size of genetlink header and netlink message header,
not user header.
This also means we don't need to pass the pointer to genetlink family and
the same is true for genl_dump_check_consistent() which is the only caller
of genlmsg_nlhdr(). (Note that at the moment, these functions are only
used for families which do not have user header so that they are not
affected.)
Fixes: 670dc2833d ("netlink: advertise incomplete dumps")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when resetting stream, if both in and out flags are set, the info
len can reach:
sizeof(struct sctp_strreset_outreq) + SCTP_MAX_STREAM(65535) +
sizeof(struct sctp_strreset_inreq) + SCTP_MAX_STREAM(65535)
even without duplicated stream no, this value is far greater than the
chunk's max size.
_sctp_make_chunk doesn't do any check for this, which would cause the
skb it allocs is huge, syzbot even reported a crash due to this.
This patch is to check stream reset info len before making reconf
chunk and return EINVAL if the len exceeds chunk's capacity.
Thanks Marcelo and Neil for making this clear.
v1->v2:
- move the check into sctp_send_reset_streams instead.
Fixes: cc16f00f65 ("sctp: add support for generating stream reconf ssn reset request chunk")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dfcb9f4f99 ("sctp: deny peeloff operation on asocs with threads
sleeping on it") fixed the race between peeloff and wait sndbuf by
checking waitqueue_active(&asoc->wait) in sctp_do_peeloff().
But it actually doesn't work, as even if waitqueue_active returns false
the waiting sndbuf thread may still not yet hold sk lock. After asoc is
peeled off, sk is not asoc->base.sk any more, then to hold the old sk
lock couldn't make assoc safe to access.
This patch is to fix this by changing to hold the new sk lock if sk is
not asoc->base.sk, meanwhile, also set the sk in sctp_sendmsg with the
new sk.
With this fix, there is no more race between peeloff and waitbuf, the
check 'waitqueue_active' in sctp_do_peeloff can be removed.
Thanks Marcelo and Neil for making this clear.
v1->v2:
fix it by changing to lock the new sock instead of adding a flag in asoc.
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_sendmsg sctp_wait_for_sndbuf could schedule out without
holding sock sk. It means the current asoc can be freed elsewhere,
like when receiving an abort packet.
If the asoc is just created in sctp_sendmsg and sctp_wait_for_sndbuf
returns err, the asoc will be freed again due to new_asoc is not nil.
An use-after-free issue would be triggered by this.
This patch is to fix it by setting new_asoc with nil if the asoc is
already dead when cpu schedules back, so that it will not be freed
again in sctp_sendmsg.
v1->v2:
set new_asoc as nil in sctp_sendmsg instead of sctp_wait_for_sndbuf.
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
