Revert some changes done in 7746383868.
Revert all changes done in hidinput_calc_abs_res as it mistakingly used
"Unit" item exponent nibbles to affect resolution value. This wasn't
breaking resolution calculation of relevant axes of any existing
devices, though, as they have only one dimension to their units and thus
1 in the corresponding nible.
Revert to reading "Unit Exponent" item value as a signed integer in
hid_parser_global to fix reading specification-complying values. This
fixes resolution calculation of devices complying to the HID standard,
including Huion, KYE, Waltop and UC-Logic graphics tablets which have
their report descriptors fixed by the drivers.
Explanations follow.
There are two "unit exponents" in HID specification and it is important
not to mix them. One is the global "Unit Exponent" item and another is
nibble values in the global "Unit" item. See 6.2.2.7 Global Items.
The "Unit Exponent" value is just a signed integer and is used to scale
the integer resolution unit values, so fractions can be expressed.
The nibbles of "Unit" value are used to select the unit system (nibble
0), and presence of a particular basic unit type in the unit formula and
its *exponent* (or power, nibbles 1-6). And yes, the latter is in two
complement and zero means absence of the unit type.
Taking the representation example of (integer) joules from the
specification:
[mass(grams)][length(centimeters)^2][time(seconds)^-2] * 10^-7
the "Unit Exponent" would be -7 (or 0xF9, if stored as a byte) and the
"Unit" value would be 0xE121, signifying:
Nibble Part Value Meaning
----- ---- ----- -------
0 System 1 SI Linear
1 Length 2 Centimeters^2
2 Mass 1 Grams
3 Time -2 Seconds^-2
To give the resolution in e.g. hundredth of joules the "Unit Exponent"
item value should have been -9.
See also the examples of "Unit" values for some common units in the same
chapter.
However, there is a common misunderstanding about the "Unit Exponent"
value encoding, where it is assumed to be stored the same as nibbles in
"Unit" item. This is most likely due to the specification being a bit
vague and overloading the term "unit exponent". This also was and still
is proliferated by the official "HID Descriptor Tool", which makes this
mistake and stores "Unit Exponent" as such. This format is also
mentioned in books such as "USB Complete" and in Microsoft's hardware
design guides.
As a result many devices currently on the market use this encoding and
so the driver should support them.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* acpi-fixes:
ACPI / PM: Drop two functions that are not used any more
ATA / ACPI: remove power dependent device handling
ACPI / power: Drop automaitc resume of power resource dependent devices
ACPI: remove /proc/acpi/event from ACPI_BUTTON help
ACPI / power: Release resource_lock after acpi_power_get_state() return error
Pavel Roskin reported that DRM_IOCTL_MODE_GETCONNECTOR was overwritting
the 4 bytes beyond the end of its structure with a 32-bit userspace
running on a 64-bit kernel. This is due to the padding gcc inserts as
the drm_mode_get_connector struct includes a u64 and its size is not a
natural multiple of u64s.
64-bit kernel:
sizeof(drm_mode_get_connector)=80, alignof=8
sizeof(drm_mode_get_encoder)=20, alignof=4
sizeof(drm_mode_modeinfo)=68, alignof=4
32-bit userspace:
sizeof(drm_mode_get_connector)=76, alignof=4
sizeof(drm_mode_get_encoder)=20, alignof=4
sizeof(drm_mode_modeinfo)=68, alignof=4
Fortuituously we can insert explicit padding to the tail of our
structures without breaking ABI.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Apply the protections from
commit 1b2f148963
Author: Dave Airlie <airlied@redhat.com>
Date: Sat Aug 14 20:20:34 2010 +1000
drm: block userspace under allocating buffer and having drivers overwrite it (v2)
to the core ioctl structs as well, for we found one instance where there
is a 32-/64-bit size mismatch and were guilty of writing beyond the end
of the user's buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull CIFS fixes from Steve French:
"Five small cifs fixes (includes fixes for: unmount hang, 2 security
related, symlink, large file writes)"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: ntstatus_to_dos_map[] is not terminated
cifs: Allow LANMAN auth method for servers supporting unencapsulated authentication methods
cifs: Fix inability to write files >2GB to SMB2/3 shares
cifs: Avoid umount hangs with smb2 when server is unresponsive
do not treat non-symlink reparse points as valid symlinks
Commit be4f154d5e
bridge: Clamp forward_delay when enabling STP
had a typo when attempting to clamp maximum forward delay.
It is possible to set bridge_forward_delay to be higher then
permitted maximum when STP is off. When turning STP on, the
higher then allowed delay has to be clamed down to max value.
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_can_gso() should only be used as a hint in tcp_sendmsg() to build GSO
packets in the first place. (As a performance hint)
Once we have GSO packets in write queue, we can not decide they are no
longer GSO only because flow now uses a route which doesn't handle
TSO/GSO.
Core networking stack handles the case very well for us, all we need
is keeping track of packet counts in MSS terms, regardless of
segmentation done later (in GSO or hardware)
Right now, if tcp_fragment() splits a GSO packet in two parts,
@left and @right, and route changed through a non GSO device,
both @left and @right have pcount set to 1, which is wrong,
and leads to incorrect packet_count tracking.
This problem was added in commit d5ac99a648 ("[TCP]: skb pcount with MTU
discovery")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP stack should make sure it owns skbs before mangling them.
We had various crashes using bnx2x, and it turned out gso_size
was cleared right before bnx2x driver was populating TC descriptor
of the _previous_ packet send. TCP stack can sometime retransmit
packets that are still in Qdisc.
Of course we could make bnx2x driver more robust (using
ACCESS_ONCE(shinfo->gso_size) for example), but the bug is TCP stack.
We have identified two points where skb_unclone() was needed.
This patch adds a WARN_ON_ONCE() to warn us if we missed another
fix of this kind.
Kudos to Neal for finding the root cause of this bug. Its visible
using small MSS.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.12 stream!
For the mac80211 bits, Johannes says:
"Jouni fixes a remain-on-channel vs. scan bug, and Felix fixes client TX
probing on VLANs."
And also:
"This time I have two fixes from Emmanuel for RF-kill issues, and fixed
two issues reported by Evan Huus and Thomas Lindroth respectively."
On top of those...
Avinash Patil adds a couple of mwifiex fixes to properly inform cfg80211
about some different types of disconnects, avoiding WARNINGs.
Mark Cave-Ayland corrects a pointer arithmetic problem in rtlwifi,
avoiding incorrect automatic gain calculations.
Solomon Peachy sends a cw1200 fix for locking around calls to
cw1200_irq_handler, addressing "lost interrupt" problems.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a QMI device, manufactured by TCT Mobile Phones.
A companion patch blacklisting this device's QMI interface in the option.c
driver has been sent.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to schedule the refill work unconditionally after changing the
number of queues. This may lead an issue if the device is not
up. Since we only try to cancel the work in ndo_stop(), this may cause
the refill work still work after removing the device. Fix this by only
schedule the work when device is up.
The bug were introduce by commit 9b9cd8024a.
(virtio-net: fix the race between channels setting and refill)
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're trying to re-configure the affinity unconditionally in cpu hotplug
callback. This may lead the issue during resuming from s3/s4 since
- virt queues haven't been allocated at that time.
- it's unnecessary since thaw method will re-configure the affinity.
Fix this issue by checking the config_enable and do nothing is we're not ready.
The bug were introduced by commit 8de4b2f3ae
(virtio-net: reset virtqueue affinity when doing cpu hotplug).
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We overwrite the ->bitrate with the user supplied information on the
next line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cap bitrate at YAM_MAXBITRATE in yam_ioctl(), but it could also be
negative. I don't know the impact of using a negative bitrate but let's
prevent it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If interrupts happen before napi_enable was called, the driver will not
work as expected. Network transmissions are impossible in this state.
This bug can be reproduced easily by restarting the network interface in
a loop. After some time any network transmissions on the network
interface will fail.
This patch fixes the bug by enabling napi before enabling the network
interface interrupts.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPS support is kind of broken on bnx2x, because only non LRO packets
get proper rx queue information. This triggers reorders, as it seems
bnx2x like to generate a non LRO packet for segment including TCP PUSH
flag : (this might be pure coincidence, but all the reorders I've
seen involve segments with a PUSH)
11:13:34.335847 IP A > B: . 415808:447136(31328) ack 1 win 457 <nop,nop,timestamp 3789336 3985797>
11:13:34.335992 IP A > B: . 447136:448560(1424) ack 1 win 457 <nop,nop,timestamp 3789336 3985797>
11:13:34.336391 IP A > B: . 448560:479888(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985797>
11:13:34.336425 IP A > B: P 511216:512640(1424) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
11:13:34.336423 IP A > B: . 479888:511216(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
11:13:34.336924 IP A > B: . 512640:543968(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
11:13:34.336963 IP A > B: . 543968:575296(31328) ack 1 win 457 <nop,nop,timestamp 3789337 3985798>
We must call skb_record_rx_queue() to properly give to RPS (and more
generally for TX queue selection on forward path) the receive queue
information.
Similar fix is needed for skb_mark_napi_id(), but will be handled
in a separate patch to ease stable backports.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On receiving an ACK that covers the loss probe sequence, TLP
immediately sets the congestion state to Open, even though some packets
are not recovered and retransmisssion are on the way. The later ACks
may trigger a WARN_ON check in step D of tcp_fastretrans_alert(), e.g.,
https://bugzilla.redhat.com/show_bug.cgi?id=989251
The fix is to follow the similar procedure in recovery by calling
tcp_try_keep_open(). The sender switches to Open state if no packets
are retransmissted. Otherwise it goes to Disorder and let subsequent
ACKs move the state to Recovery or Open.
Reported-By: Michael Sterrett <michael@sterretts.net>
Tested-By: Dormando <dormando@rydia.net>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENOMEM in the padding pkt alloc fail error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For now, we disable the extended MMAP record support (MMAP2).
We have identified cases where it would not report the correct mapping
information, clone(VM_CLONE) but with separate pids. We will revisit
the support once we find a solution for this case.
The patch changes the kernel to return EINVAL if attr->mmap2 is set. The
patch also modifies the perf tool to use regular PERF_RECORD_MMAP for
synthetic events and it also prevents the tool from requesting
attr->mmap2 mode because the kernel would reject it.
The support will be revisited once the kenrel interface is updated.
In V2, we reduce the patch to the strict minimum.
In V3, we avoid calling perf_event_open() with mmap2 set because we know
it will fail and require fallback retry.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20131017173215.GA8820@quad
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Vlad Yasevich says:
====================
sctp: Use software checksum under certain circumstances.
There are some cards that support SCTP checksum offloading. When using
these cards with IPSec or forcing IP fragmentation of SCTP traffic,
the checksum is computed incorrectly due to the fact that xfrm and IP/IPv6
fragmentation code do not know that this is SCTP traffic and do not
know that checksum has to be computed differently.
To fix this, we let SCTP detect these conditions and perform software
checksum calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IP/IPv6 fragmentation knows how to compute only TCP/UDP checksum.
This causes problems if SCTP packets has to be fragmented and
ipsummed has been set to PARTIAL due to checksum offload support.
This condition can happen when retransmitting after MTU discover,
or when INIT or other control chunks are larger then MTU.
Check for the rare fragmentation condition in SCTP and use software
checksum calculation in this case.
CC: Fan Du <fan.du@windriver.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb/ixgbe have hardware sctp checksum support, when this feature is enabled
and also IPsec is armed to protect sctp traffic, ugly things happened as
xfrm_output checks CHECKSUM_PARTIAL to do checksum operation(sum every thing
up and pack the 16bits result in the checksum field). The result is fail
establishment of sctp communication.
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst->xfrm is conditionally defined. Provide accessor funtion that
is always available.
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cast __u64 to u64 to silence this warning on older distros, such as
Fedora 12:
CC /tmp/build/perf/util/scripting-engines/trace-event-perl.o
cc1: warnings being treated as errors
util/scripting-engines/trace-event-perl.c: In function ‘perl_process_tracepoint’:
util/scripting-engines/trace-event-perl.c:285: error: format ‘%lu’ expects type ‘long unsigned int’, but argument 2 has type ‘__u64’
make[1]: *** [/tmp/build/perf/util/scripting-engines/trace-event-perl.o] Error 1
make: *** [install] Error 2
make: Leaving directory `/home/acme/git/linux/tools/perf'
[acme@fedora12 linux]$
Reported-by: Waiman Long <Waiman.Long@hp.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Link: http://lkml.kernel.org/n/tip-nlxofdqcdjfm0w9o6bgq4kqv@git.kernel.org
Link: http://lkml.kernel.org/r/1381265120-58532-1-git-send-email-Waiman.Long@hp.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Here is one fix for the hotplug memory path that resolves a regression
when removing memory that showed up in 3.12-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJgHqMACgkQMUfUDdst+ykplQCgym3aZCnwCAASgrM5g0fyM5LW
eR4AmQGqYBZBticsmGqLWDyUksrnL/6S
=zRIr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is one fix for the hotplug memory path that resolves a regression
when removing memory that showed up in 3.12-rc1"
* tag 'driver-core-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Release device_hotplug_lock when store_mem_state returns EINVAL
Here are some USB fixes and new device ids for 3.12-rc6
The largest change here is a bunch of new device ids for the option USB
serial driver for new Huawei devices. Other than that, just some small
bug fixes for issues that people have reported (run-time and
build-time), nothing major.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJgHZMACgkQMUfUDdst+yl5xgCePinICkasywmkWO0CgndCelCx
nyMAoIQ51ot0igMbmXoSAyq5u0EgVHmG
=/iU9
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 3.12-rc6
The largest change here is a bunch of new device ids for the option
USB serial driver for new Huawei devices. Other than that, just some
small bug fixes for issues that people have reported (run-time and
build-time), nothing major"
* tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
usb/chipidea: fix oops on memory allocation failure
usb-storage: add quirk for mandatory READ_CAPACITY_16
usb: serial: option: blacklist Olivetti Olicard200
USB: quirks: add touchscreen that is dazzeled by remote wakeup
Revert "usb: musb: gadget: fix otg active status flag"
USB: quirks.c: add one device that cannot deal with suspension
USB: serial: option: add support for Inovia SEW858 device
USB: serial: ti_usb_3410_5052: add Abbott strip port ID to combined table as well.
USB: support new huawei devices in option.c
usb: musb: start musb on the udc side, too
xhci: Fix spurious wakeups after S5 on Haswell
xhci: fix write to USB3_PSSEN and XUSB2PRM pci config registers
xhci: quirk for extra long delay for S4
xhci: Don't enable/disable RWE on bus suspend/resume.
Here are two serial driver fixes for your tree. One is a revert of a
patch that causes a build error, the other is a fix to provide the
correct brace placement which resolves a bug where the driver was not
working properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJgH5oACgkQMUfUDdst+yn5ywCfU4Xq4jDcUyc3pEoKfX2kkNZk
7a8An2brQo3h20xHsIv2NprgYqCjfZpx
=rcEE
-----END PGP SIGNATURE-----
Merge tag 'tty-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are two serial driver fixes for your tree. One is a revert of a
patch that causes a build error, the other is a fix to provide the
correct brace placement which resolves a bug where the driver was not
working properly"
* tag 'tty-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: vt8500: add missing braces
Revert "serial: i.MX: evaluate linux,stdout-path property"
Here are some small iio and w1 driver fixes for 3.12-rc6.
There is also a hyper-v fix in here, which turned out to be incorrect,
so it was reverted. That will probably have to wait unto 3.13-rc1 to
get accepted as it's still being discussed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJgHiwACgkQMUfUDdst+ykS3gCgiJqKAbzsb+hNiI/AXmCHtcWV
cK4AoIEXbg+nMYPzSuSPz1nr2vJPr3CP
=5WpE
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small iio and w1 driver fixes for 3.12-rc6.
There is also a hyper-v fix in here, which turned out to be incorrect,
so it was reverted. That will probably have to wait unto 3.13-rc1 to
get accepted as it's still being discussed"
* tag 'char-misc-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "Drivers: hv: vmbus: Fix a bug in channel rescind code"
Drivers: hv: vmbus: Fix a bug in channel rescind code
iio:buffer: Free active scan mask in iio_disable_all_buffers()
iio: frequency: adf4350: add missing clk_disable_unprepare() on error in adf4350_probe()
w1 - call request_module with w1 master mutex unlocked
w1 - fix fops in w1_bus_notify
Nikita Kiryanov says:
====================
dm9000 improvements
This is a collection of improvements and bug fixes for dm9000, mostly
related to its startup and resume-from-suspend sequences.
Patch "Implement full reset of DM9000 network device" was submitted to the
linux-kernel mailing list but never applied.
An archive of the submission and the following conversation can be found here:
http://lkml.indiana.edu/hypermail/linux/kernel/1205.2/02817.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the LPA by checking mii_if_info, instead of just saying "no LPA" every
time.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Davicom application note for the DM9000 network device recommends
performing software reset twice to correctly initialise the device.
Without this reset some devices fail to initialise correctly on
system startup.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take the phy out of reset explicitly during system resume to avoid
losing network connectivity.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the changes introduced in commit 6741f40 (DM9000B: driver
initialization upgrade) break functionality on DM9000A
(error message during NFS boot: "dm9000 dm9000.0: eth0: link down")
Since the changes were meant to serve only DM9000B, make them
dependent on the chip type.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
All reasonably small fixes as rc6: a HD-audio mic fix, a us122l mmap
regression fix, and kernel memory leak fix in hdsp driver.
Hopefully this will be the last pull request for 3.12...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=AeDk
-----END PGP SIGNATURE-----
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All reasonably small fixes as rc6: a HD-audio mic fix, a us122l mmap
regression fix, and kernel memory leak fix in hdsp driver. Hopefully
this will be the last pull request for 3.12..."
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hdsp - info leak in snd_hdsp_hwdep_ioctl()
ALSA: us122l: Fix pcm_usb_stream mmapping regression
ALSA: hda - Fix inverted internal mic not indicated on some machines
Pull apparmor fixes from James Morris:
"A couple more regressions fixed"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
apparmor: fix bad lock balance when introspecting policy
apparmor: fix memleak of the profile hash
Two little ones this time:
1) A missing clk_unprepare in adf4350.
2) A missing free of the active_scan_mask when iio_disable_all_buffers is
called during an unexpected device removal. This leak was introduced by
the fix
a87c82e454 iio: Stop sampling when the device is removed
and hence is a regression fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Whi7
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.12c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
Third set of IIO fixes for the 3.12 cycle.
Two little ones this time:
1) A missing clk_unprepare in adf4350.
2) A missing free of the active_scan_mask when iio_disable_all_buffers is
called during an unexpected device removal. This leak was introduced by
the fix
a87c82e454 iio: Stop sampling when the device is removed
and hence is a regression fix.
Commit 3fa4d734 (usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv)
changed the conditional around the declaration of usb_nop_xceiv_register
from
#if defined(CONFIG_NOP_USB_XCEIV) ||
(defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))
to
#if IS_ENABLED(CONFIG_NOP_USB_XCEIV)
While that looks the same, it is semantically different. The first expression
is true if CONFIG_NOP_USB_XCEIV is built as module and if the including
code is built as module. The second expression is true if code depending on
CONFIG_NOP_USB_XCEIV if built as module or into the kernel.
As a result, the arm:allmodconfig build fails with
arch/arm/mach-omap2/built-in.o: In function `omap3_evm_init':
arch/arm/mach-omap2/board-omap3evm.c:703: undefined reference to
`usb_nop_xceiv_register'
Fix the problem by reverting to the old conditional.
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 90d33f3ec5 as it's not
the correct fix for this issue, and it causes a build warning to be
added to the kernel tree.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two functions defined in device_pm.c, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), have no callers and may be
dropped, so drop them.
Moreover, they are the only functions adding entries to and removing
entries from the power_dependent list in struct acpi_device, so drop
that list too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Previously, we wanted SCSI devices corrsponding to ATA devices to
be runtime resumed when the power resource for those ATA device was
turned on by some other device, so we added the SCSI device to the
dependent device list of the ATA device's ACPI node. However, this
code has no effect after commit 41863fc (ACPI / power: Drop automaitc
resume of power resource dependent devices) and the mechanism it was
supposed to implement is regarded as a bad idea now, so drop it.
[rjw: Changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
mm: revert mremap pud_free anti-fix
mm: fix BUG in __split_huge_page_pmd
swap: fix set_blocksize race during swapon/swapoff
procfs: call default get_unmapped_area on MMU-present architectures
procfs: fix unintended truncation of returned mapped address
writeback: fix negative bdi max pause
percpu_refcount: export symbols
fs: buffer: move allocation failure loop into the allocator
mm: memcg: handle non-error OOM situations more gracefully
tools/testing/selftests: fix uninitialized variable
block/partitions/efi.c: treat size mismatch as a warning, not an error
mm: hugetlb: initialize PG_reserved for tail pages of gigantic compound pages
mm/zswap: bugfix: memory leak when re-swapon
mm: /proc/pid/pagemap: inspect _PAGE_SOFT_DIRTY only on present pages
mm: migration: do not lose soft dirty bit if page is in migration state
gcov: MAINTAINERS: Add an entry for gcov
mm/hugetlb.c: correct missing private flag clearing
mm/vmscan.c: don't forget to free shrinker->nr_deferred
ipc/sem.c: synchronize semop and semctl with IPC_RMID
ipc: update locking scheme comments
...
Revert commit 1ecfd533f4 ("mm/mremap.c: call pud_free() after fail
calling pmd_alloc()").
The original code was correct: pud_alloc(), pmd_alloc(), pte_alloc_map()
ensure that the pud, pmd, pt is already allocated, and seldom do they
need to allocate; on failure, upper levels are freed if appropriate by
the subsequent do_munmap(). Whereas commit 1ecfd533f4 did an
unconditional pud_free() of a most-likely still-in-use pud: saved only
by the near-impossiblity of pmd_alloc() failing.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Occasionally we hit the BUG_ON(pmd_trans_huge(*pmd)) at the end of
__split_huge_page_pmd(): seen when doing madvise(,,MADV_DONTNEED).
It's invalid: we don't always have down_write of mmap_sem there: a racing
do_huge_pmd_wp_page() might have copied-on-write to another huge page
before our split_huge_page() got the anon_vma lock.
Forget the BUG_ON, just go back and try again if this happens.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix race between swapoff and swapon. Swapoff used old_block_size from
swap_info outside of swapon_mutex so it could be overwritten by
concurrent swapon.
The race has visible effect only if more than one swap block device
exists with different block sizes (e.g. /dev/sda1 with block size 4096
and /dev/sdb1 with 512). In such case it leads to setting the blocksize
of swapped off device with wrong blocksize.
The bug can be triggered with multiple concurrent swapoff and swapon:
0. Swap for some device is on.
1. swapoff:
First the swapoff is called on this device and "struct swap_info_struct
*p" is assigned. This is done under swap_lock however this lock is
released for the call try_to_unuse().
2. swapon:
After the assignment above (and before acquiring swapon_mutex &
swap_lock by swapoff) the swapon is called on the same device.
The p->old_block_size is assigned to the value of block_size the device.
This block size should be the same as previous but sometimes it is not.
The swapon ends successfully.
3. swapoff:
Swapoff resumes, grabs the locks and mutex and continues to disable this
swap device. Now it sets the block size to value taken from swap_info
which was overwritten by swapon in 2.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Weijie Yang <weijie.yang.kh@gmail.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Shaohua Li <shli@fusionio.com>
Cc: Minchan Kim <minchan@kernel.org>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c4fe244857 ("sparc: fix PCI device proc file mmap(2)") added
proc_reg_get_unmapped_area in proc_reg_file_ops and
proc_reg_file_ops_no_compat, by which now mmap always returns EIO if
get_unmapped_area method is not defined for the target procfs file,
which causes regression of mmap on /proc/vmcore.
To address this issue, like get_unmapped_area(), call default
current->mm->get_unmapped_area on MMU-present architectures if
pde->proc_fops->get_unmapped_area, i.e. the one in actual file
operation in the procfs file, is not defined.
Reported-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, proc_reg_get_unmapped_area truncates upper 32-bit of the
mapped virtual address returned from get_unmapped_area method in
pde->proc_fops due to the variable rv of signed integer on x86_64. This
is too small to have vitual address of unsigned long on x86_64 since on
x86_64, signed integer is of 4 bytes while unsigned long is of 8 bytes.
To fix this issue, use unsigned long instead.
Fixes a regression added in commit c4fe244857 ("sparc: fix PCI device
proc file mmap(2)").
Signed-off-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toralf runs trinity on UML/i386. After some time it hangs and the last
message line is
BUG: soft lockup - CPU#0 stuck for 22s! [trinity-child0:1521]
It's found that pages_dirtied becomes very large. More than 1000000000
pages in this case:
period = HZ * pages_dirtied / task_ratelimit;
BUG_ON(pages_dirtied > 2000000000);
BUG_ON(pages_dirtied > 1000000000); <---------
UML debug printf shows that we got negative pause here:
ick: pause : -984
ick: pages_dirtied : 0
ick: task_ratelimit: 0
pause:
+ if (pause < 0) {
+ extern int printf(char *, ...);
+ printf("ick : pause : %li\n", pause);
+ printf("ick: pages_dirtied : %lu\n", pages_dirtied);
+ printf("ick: task_ratelimit: %lu\n", task_ratelimit);
+ BUG_ON(1);
+ }
trace_balance_dirty_pages(bdi,
Since pause is bounded by [min_pause, max_pause] where min_pause is also
bounded by max_pause. It's suspected and demonstrated that the
max_pause calculation goes wrong:
ick: pause : -717
ick: min_pause : -177
ick: max_pause : -717
ick: pages_dirtied : 14
ick: task_ratelimit: 0
The problem lies in the two "long = unsigned long" assignments in
bdi_max_pause() which might go negative if the highest bit is 1, and the
min_t(long, ...) check failed to protect it falling under 0. Fix all of
them by using "unsigned long" throughout the function.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Toralf Förster <toralf.foerster@gmx.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Richard Weinberger <richard@nod.at>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the interface to be used within modules.
Signed-off-by: Matias Bjorling <m@bjorling.me>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
