There is a scenario that can end up with rebuild process failing to
return good content, i.e.
suppose that all disks can be read without problems and if the content
that was read out doesn't match its checksum, currently for raid6
btrfs at most retries twice,
- the 1st retry is to rebuild with all other stripes, it'll eventually
be a raid5 xor rebuild,
- if the 1st fails, the 2nd retry will deliberately fail parity p so
that it will do raid6 style rebuild,
however, the chances are that another non-parity stripe content also
has something corrupted, so that the above retries are not able to
return correct content, and users will think of this as data loss.
More seriouly, if the loss happens on some important internal btree
roots, it could refuse to mount.
This extends btrfs to do more retries and each retry fails only one
stripe. Since raid6 can tolerate 2 disk failures, if there is one
more failure besides the failure on which we're recovering, this can
always work.
The worst case is to retry as many times as the number of raid6 disks,
but given the fact that such a scenario is really rare in practice,
it's still acceptable.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In fact nobody is waiting on @wait's waitqueue, it can be safely
removed.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The defined wait is not used anywhere.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The local bio_list may have pending bios when doing cleanup, it can
end up with memory leak if they don't get freed.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
After mapping block with BTRFS_MAP_WRITE, parities have been sorted to
the end position, so this search can start from the first parity
stripe.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ copied changelog as a comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
This fixes several instances of blk_status_t and bare errno ints being
mixed up, some of which are real bugs.
In the normal case, 0 matches BLK_STS_OK, so we don't observe any
effects of the missing conversion, but in case of errors or passes
through the repair/retry paths, the errors get mixed up.
The changes were identified using 'sparse', we don't have reports of the
buggy behaviour.
Fixes: 4e4cbee93d ("block: switch bios to blk_status_t")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull btrfs fixes from David Sterba:
"We've identified and fixed a silent corruption (introduced by code in
the first pull), a fixup after the blk_status_t merge and two fixes to
incremental send that Filipe has been hunting for some time"
* 'for-4.13-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix unexpected return value of bio_readpage_error
btrfs: btrfs_create_repair_bio never fails, skip error handling
btrfs: cloned bios must not be iterated by bio_for_each_segment_all
Btrfs: fix write corruption due to bio cloning on raid5/6
Btrfs: incremental send, fix invalid memory access
Btrfs: incremental send, fix invalid path for link commands
Pull btrfs updates from David Sterba:
"The core updates improve error handling (mostly related to bios), with
the usual incremental work on the GFP_NOFS (mis)use removal,
refactoring or cleanups. Except the two top patches, all have been in
for-next for an extensive amount of time.
User visible changes:
- statx support
- quota override tunable
- improved compression thresholds
- obsoleted mount option alloc_start
Core updates:
- bio-related updates:
- faster bio cloning
- no allocation failures
- preallocated flush bios
- more kvzalloc use, memalloc_nofs protections, GFP_NOFS updates
- prep work for btree_inode removal
- dir-item validation
- qgoup fixes and updates
- cleanups:
- removed unused struct members, unused code, refactoring
- argument refactoring (fs_info/root, caller -> callee sink)
- SEARCH_TREE ioctl docs"
* 'for-4.13-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (115 commits)
btrfs: Remove false alert when fiemap range is smaller than on-disk extent
btrfs: Don't clear SGID when inheriting ACLs
btrfs: fix integer overflow in calc_reclaim_items_nr
btrfs: scrub: fix target device intialization while setting up scrub context
btrfs: qgroup: Fix qgroup reserved space underflow by only freeing reserved ranges
btrfs: qgroup: Introduce extent changeset for qgroup reserve functions
btrfs: qgroup: Fix qgroup reserved space underflow caused by buffered write and quotas being enabled
btrfs: qgroup: Return actually freed bytes for qgroup release or free data
btrfs: qgroup: Cleanup btrfs_qgroup_prepare_account_extents function
btrfs: qgroup: Add quick exit for non-fs extents
Btrfs: rework delayed ref total_bytes_pinned accounting
Btrfs: return old and new total ref mods when adding delayed refs
Btrfs: always account pinned bytes when dropping a tree block ref
Btrfs: update total_bytes_pinned when pinning down extents
Btrfs: make BUG_ON() in add_pinned_bytes() an ASSERT()
Btrfs: make add_pinned_bytes() take an s64 num_bytes instead of u64
btrfs: fix validation of XATTR_ITEM dir items
btrfs: Verify dir_item in iterate_object_props
btrfs: Check name_len before in btrfs_del_root_ref
btrfs: Check name_len before reading btrfs_get_name
...
We can hardcode GFP_NOFS to btrfs_io_bio_alloc, although it means we
change it back from GFP_KERNEL in scrub. I'd rather save a few stack
bytes from not passing the gfp flags in the remaining, more imporatant,
contexts and the bio allocating API now looks more consistent.
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Update direct callers of btrfs_io_bio_alloc that do error handling, that
we can now remove.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The logic of kmalloc and vmalloc fallback is opencoded in
several places, we can now use the existing helper.
Signed-off-by: David Sterba <dsterba@suse.com>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When raid56 dev-replace is cancelled by running scrub, we will free
target device without waiting for in-flight bios, causing the following
NULL pointer deference or general protection failure.
BUG: unable to handle kernel NULL pointer dereference at 00000000000005e0
IP: generic_make_request_checks+0x4d/0x610
CPU: 1 PID: 11676 Comm: kworker/u4:14 Tainted: G O 4.11.0-rc2 #72
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.10.2-20170228_101828-anatol 04/01/2014
Workqueue: btrfs-endio-raid56 btrfs_endio_raid56_helper [btrfs]
task: ffff88002875b4c0 task.stack: ffffc90001334000
RIP: 0010:generic_make_request_checks+0x4d/0x610
Call Trace:
? generic_make_request+0xc7/0x360
generic_make_request+0x24/0x360
? generic_make_request+0xc7/0x360
submit_bio+0x64/0x120
? page_in_rbio+0x4d/0x80 [btrfs]
? rbio_orig_end_io+0x80/0x80 [btrfs]
finish_rmw+0x3f4/0x540 [btrfs]
validate_rbio_for_rmw+0x36/0x40 [btrfs]
raid_rmw_end_io+0x7a/0x90 [btrfs]
bio_endio+0x56/0x60
end_workqueue_fn+0x3c/0x40 [btrfs]
btrfs_scrubparity_helper+0xef/0x620 [btrfs]
btrfs_endio_raid56_helper+0xe/0x10 [btrfs]
process_one_work+0x2af/0x720
? process_one_work+0x22b/0x720
worker_thread+0x4b/0x4f0
kthread+0x10f/0x150
? process_one_work+0x720/0x720
? kthread_create_on_node+0x40/0x40
ret_from_fork+0x2e/0x40
RIP: generic_make_request_checks+0x4d/0x610 RSP: ffffc90001337bb8
In btrfs_dev_replace_finishing(), we will call
btrfs_rm_dev_replace_blocked() to wait bios before destroying the target
device when scrub is finished normally.
However when dev-replace is aborted, either due to error or cancelled by
scrub, we didn't wait for bios, this can lead to use-after-free if there
are bios holding the target device.
Furthermore, for raid56 scrub, at least 2 places are calling
btrfs_map_sblock() without protection of bio_counter, leading to the
problem.
This patch fixes the problem:
1) Wait for bio_counter before freeing target device when canceling
replace
2) When calling btrfs_map_sblock() for raid56, use bio_counter to
protect the call.
Cc: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In raid56 scenario, after trying parity recovery, we didn't set
mirror_num for btrfs_bio with failed mirror_num, hence
end_bio_extent_readpage() will report a random mirror_num in dmesg
log.
Cc: David Sterba <dsterba@suse.cz>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Variable 'walk' in lock_stripe_add() is not used. Remove it.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are loads of functions in btrfs that accept a root parameter
but only use it to obtain an fs_info pointer. Let's convert those to
just accept an fs_info pointer directly.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In routines where someptr->fs_info is referenced multiple times, we
introduce a convenience variable. This makes the code considerably
more readable.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We track the node sizes per-root, but they never vary from the values
in the superblock. This patch messes with the 80-column style a bit,
but subsequent patches to factor out root->fs_info into a convenience
variable fix it up again.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Just use bio_for_each_segment_all to iterate over all segments.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This BUG() has been triggered by a fuzz testing image, which contains
an invalid chunk type, ie. a single stripe chunk has the raid6 type.
Btrfs can handle this gracefully by returning -EIO, so besides using
btrfs_warn to give us more debugging information rather than a single
BUG(), we can return error properly.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This should be the easier cases to convert btrfs to
bio_set_op_attrs/bio_op.
They are mostly just cut and replace type of changes.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to create additional end_io function for scrub, it increased
code size and introduced some un-unified lines, as:
raid_write_parity_end_io():
int err = bio->bi_error;
if (bio->bi_error)
raid_write_end_io():
int err = bio->bi_error;
if (err)
This patch combines them.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
PageUptodate flag already initialized to 0 for new page,
no need to set it again.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
We can use rbio->stripe_npages to reduce unnecessary calculation in
many code place.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
We are using different index calculation method for stripe_page in
current code:
1: (rbio->stripe_len / PAGE_CACHE_SIZE) * stripe_index + page_index
2: DIV_ROUND_UP(rbio->stripe_len, PAGE_CACHE_SIZE) * stripe_index + page_index
3: DIV_ROUND_UP(rbio->stripe_len * stripe_index, PAGE_CACHE_SIZE) + page_index
...
They can get same result when stripe_len align to PAGE_CACHE_SIZE,
this is why current code can work, intruduce and use a common function
for calculation is a better choose.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Current code is trying to calculate rbio->dbitmap's size to make it
align to sizeof(long), but implement haven't achived this object,
it is align to sizeof(char) instead.
This patch fixed above calculation, and use sizeof(long) instead of
fixed "8" to increate compatibility.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Pull btrfs updates from Chris Mason:
"This has Jeff Mahoney's long standing trim patch that fixes corners
where trims were missing. Omar has some raid5/6 fixes, especially for
using scrub and device replace when devices are missing.
Zhao Lie continues cleaning and fixing things, this series fixes some
really hard to hit corners in xfstests. I had to pull it last merge
window due to some deadlocks, but those are now resolved.
I added support for Tejun's new blkio controllers. It seems to work
well for single devices, we'll expand to multi-device as well"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (47 commits)
btrfs: fix compile when block cgroups are not enabled
Btrfs: fix file read corruption after extent cloning and fsync
Btrfs: check if previous transaction aborted to avoid fs corruption
btrfs: use __GFP_NOFAIL in alloc_btrfs_bio
btrfs: Prevent from early transaction abort
btrfs: Remove unused arguments in tree-log.c
btrfs: Remove useless condition in start_log_trans()
Btrfs: add support for blkio controllers
Btrfs: remove unused mutex from struct 'btrfs_fs_info'
Btrfs: fix parity scrub of RAID 5/6 with missing device
Btrfs: fix device replace of a missing RAID 5/6 device
Btrfs: add RAID 5/6 BTRFS_RBIO_REBUILD_MISSING operation
Btrfs: count devices correctly in readahead during RAID 5/6 replace
Btrfs: remove misleading handling of missing device scrub
btrfs: fix clone / extent-same deadlocks
Btrfs: fix defrag to merge tail file extent
Btrfs: fix warning in backref walking
btrfs: Add WARN_ON() for double lock in btrfs_tree_lock()
btrfs: Remove root argument in extent_data_ref_count()
btrfs: Fix wrong comment of btrfs_alloc_tree_block()
...
The current RAID 5/6 recovery code isn't quite prepared to handle
missing devices. In particular, it expects a bio that we previously
attempted to use in the read path, meaning that it has valid pages
allocated. However, missing devices have a NULL blkdev, and we can't
call bio_add_page() on a bio with a NULL blkdev. We could do manual
manipulation of bio->bi_io_vec, but that's pretty gross. So instead, add
a separate path that allows us to manually add pages to the rbio.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Convert kmalloc(nr * size, ..) to kmalloc_array that does additional
overflow checks, the zeroing variant is kcalloc.
Signed-off-by: David Sterba <dsterba@suse.cz>
A new helper kvfree() in mm/utils.c will do this.
Signed-off-by: Wang Shilong <wangshilong1991@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Corrent code use many kinds of "clever" way to determine operation
target's raid type, as:
raid_map != NULL
or
raid_map[MAX_NR] == RAID[56]_Q_STRIPE
To make code easy to maintenance, this patch put raid type into
bbio, and we can always get raid type from bbio with a "stupid"
way.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
1: ref_count is simple than current RBIO_HOLD_BBIO_MAP_BIT flag
to keep btrfs_bio's memory in raid56 recovery implement.
2: free function for bbio will make code clean and flexible, plus
forced data type checking in compile.
Changelog v1->v2:
Rename following by David Sterba's suggestion:
put_btrfs_bio() -> btrfs_put_bio()
get_btrfs_bio() -> btrfs_get_bio()
bbio->ref_count -> bbio->refs
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
It can make code more simple and clear, we need not care about
free bbio and raid_map together.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
The commit c404e0dc (Btrfs: fix use-after-free in the finishing
procedure of the device replace) fixed a use-after-free problem
which happened when removing the source device at the end of device
replace, but at that time, btrfs didn't support device replace
on raid56, so we didn't fix the problem on the raid56 profile.
Currently, we implemented device replace for raid56, so we need
kick that problem out before we enable that function for raid56.
The fix method is very simple, we just increase the bio per-cpu
counter before we submit a raid56 io, and decrease the counter
when the raid56 io ends.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
This function reused the code of parity scrub, and we just write
the right parity or corrected parity into the target device before
the parity scrub end.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
The implementation is simple:
- In order to avoid changing the code logic of btrfs_map_bio and
RAID56, we add the stripes of the replace target devices at the
end of the stripe array in btrfs bio, and we sort those target
device stripes in the array. And we keep the number of the target
device stripes in the btrfs bio.
- Except write operation on RAID56, all the other operation don't
take the target device stripes into account.
- When we do write operation, we read the data from the common devices
and calculate the parity. Then write the dirty data and new parity
out, at this time, we will find the relative replace target stripes
and wirte the relative data into it.
Note: The function that copying old data on the source device to
the target device was implemented in the past, it is similar to
the other RAID type.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
The implementation is:
- Read and check all the data with checksum in the same stripe.
All the data which has checksum is COW data, and we are sure
that it is not changed though we don't lock the stripe. because
the space of that data just can be reclaimed after the current
transction is committed, and then the fs can use it to store the
other data, but when doing scrub, we hold the current transaction,
that is that data can not be recovered, it is safe that read and check
it out of the stripe lock.
- Lock the stripe
- Read out all the data without checksum and parity
The data without checksum and the parity may be changed if we don't
lock the stripe, so we need read it in the stripe lock context.
- Check the parity
- Re-calculate the new parity and write back it if the old parity
is not right
- Unlock the stripe
If we can not read out the data or the data we read is corrupted,
we will try to repair it. If the repair fails. we will mark the
horizontal sub-stripe(pages on the same horizontal) as corrupted
sub-stripe, and we will skip the parity check and repair of that
horizontal sub-stripe.
And in order to skip the horizontal sub-stripe that has no data, we
introduce a bitmap. If there is some data on the horizontal sub-stripe,
we will the relative bit to 1, and when we check and repair the
parity, we will skip those horizontal sub-stripes that the relative
bits is 0.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
We will introduce new operation type later, if we still use integer
variant as bool variant to record the operation type, we would add new
variant and increase the size of raid bio structure. It is not good,
by this patch, we define different number for different operation,
and we can just use a variant to record the operation type.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
This patch implement the RAID5/6 common data repair function, the
implementation is similar to the scrub on the other RAID such as
RAID1, the differentia is that we don't read the data from the
mirror, we use the data repair function of RAID5/6.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
