This is the gereric part of R4000/R4400 errata workarounds. They include
compiler and assembler support as well as some source code modifications
to address the problems with some combinations of multiply/divide+shift
instructions as well as the daddi and daddiu instructions.
Changes included are as follows:
1. New Kconfig options to select workarounds by platforms as necessary.
2. Arch top-level Makefile to pass necessary options to the compiler; also
incompatible configurations are detected (-mno-sym32 unsupported as
horribly intrusive for little gain).
3. Bug detection updated and shuffled -- the multiply/divide+shift problem
is lethal enough that if not worked around it makes the kernel crash in
time_init() because of a division by zero; the daddiu erratum might
also trigger early potentially, though I have not observed it. On the
other hand the daddi detection code requires the exception subsystem to
have been initialised (and is there mainly for information).
4. r4k_daddiu_bug() added so that the existence of the erratum can be
queried by code at the run time as necessary; useful for generated code
like TLB fault and copy/clear page handlers.
5. __udelay() updated as it uses multiplication in inline assembly.
Note that -mdaddi requires modified toolchain (which has been maintained
by myself and available from my site for ~4years now -- versions covered
are GCC 2.95.4 - 4.1.2 and binutils from 2.13 onwards). The -mfix-r4000
and -mfix-r4400 have been standard for a while though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch below fixes two problems for Kconfig on the BCM47xx platform:
- arch/mips/bcm47xx/gpio.c uses ssb_extif_* functions. Selecting
SSB_DRIVER_EXTIF makes sure those functions are available.
- arch/mips/pci/pci.c needs, when enabled, platform specific functions,
which are defined when SSB_PCICORE_HOSTMODE is enabled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_NO_HZ, CONFIG_HIGH_RES_TIMERS should be selected in "Kernel
type" menu, not in "CPU selection" menu.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cleanup 09cadedbdc broke the oprofile
configuration for MIPS by allowing oprofile support to be built for
kernel models where oprofile doesn't have a chance in hell to work.
Just a dependecy list on a number of architectures is - surprise - broken
and should as per past discussions probably in most considered to be
broken in most cases. So I introduce a dependency for the oprofile
configuration on ARCH_SUPPORTS_OPROFILE.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sibyte SOCs only have 32-bit PCI. Due to the sparse use of the address
space only the first 1GB of memory is mapped at physical addresses
below 1GB. If a system has more than 1GB of memory 32-bit DMA will
not be able to reach all of it.
For now this patch is good enough to keep Sibyte users happy but it seems
eventually something like swiotlb will be needed for Sibyte.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In particular as-is it's not suited for multicore and mutiprocessors
systems where there is on guarantee that the counter are synchronized
or running from the same clock at all. This broke Sibyte and probably
others since the "[MIPS] Handle R4000/R4400 mfc0 from count register."
commit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Shadow register support would not possibly have worked on multicore
systems. The support code for it was also depending not on MIPS R2 but
VSMP or SMTC kernels even though it makes perfect sense with UP kernels.
SR sets are a scarce resource and the expected usage pattern is that
users actually hardcode the register set numbers in their code. So fix
the allocator by ditching it. Move the remaining CPU probe bits into
the generic CPU probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert jmr3927_clock_event_device to more generic
txx9tmr_clock_event_device which supports one-shot mode. The
txx9tmr_clock_event_device can be used for TX49 too if the cp0 timer
interrupt was not available.
Convert jmr3927_hpt_read to txx9_clocksource driver which does not
depends jiffies anymore. The txx9_clocksource itself can be used for
TX49, but normally TX49 uses higher precision clocksource_mips.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And make use of it for Cobalt. A few others such as the Malta could make
use of it as well.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Quoting Randy:
"It seems sad that this patch sources Kconfig.marker, a 7-line file,
20-something times. Yes, you (we) don't want to put those 7 lines into
20-something different files, so sourcing is the right thing.
However, what you did for avr32 seems more on the right track to me: make
_one_ Instrumentation support menu that includes PROFILING, OPROFILE, KPROBES,
and MARKERS and then use (source) that in all of the arches."
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel currently only supports broadcasting of the timer interrupt
from a single timer, not multicasting into two multicast groups of
processors. So the implemented mechanism for SMTC works by broadcasting
the cp0 compare interrupt on VPE 0 and ignoring it on any additional VPEs.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This replaces the MIPS-specific to_tm function with the generic
rtc_time_to_tm function. The big difference between the two functions is
that rtc_time_to_tm uses epoch 70 while to_tm uses 1970, so the result of
rtc_time_to_tm needs to be fixed up.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add CFE support to the BCM47XX code. That includes querying CFE environment
variables as well as using CFE to print messages before the serial port is
initialized (early printk).
Signed-off-by: Aurelien Jarno <aurel32@farad.aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the platform independent part of the CFE code to arch/mips/fw/cfe from
arch/mips/sibyte/cfe.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Note that the BCM4710 does not support the wait instruction, this
is not a mistake in the code.
It originally comes from the OpenWrt patches.
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Florian Schirmer <jolt@tuxbox.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We do not rely on user anymore to setup this config correctly.
Instead we make our choice depending on the load address.
If we want to force Kbuild to use ELF64 format whatever
the load address we can still do:
$ make BUILD_ELF32=no
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/basler/excite/excite_prom.o
arch/mips/basler/excite/excite_prom.c:136:3: #error 64 bit support not implemented
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add generic irq_chip for TX39/TX49 SoCs. This can be replace
jmr3927_irq_irc, tx4927_irq_pic_type and tx4938_irq_pic_type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While the PC speaker is wired up to the i8254 there is more to the i8254
than just the PC speaker so this code was getting in the way under its
current name.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To support multiple TC microthreads acting as "CPUs" within a VPE,
VPE-wide interrupt mask bits must be specially manipulated during
interrupt handling. To support legacy drivers and interrupt controller
management code, SMTC has a "backstop" to track and if necessary restore
the interrupt mask. This has some performance impact on interrupt service
overhead. Disable it only if you know what you are doing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GPIO 0..15 are for TX4938 PIO pins, GPIO 16..18 are for FPGA-driven
chipselect signals for SPI devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add mips common support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are no I/O ports on the DECstation whatsoever in any configuration
as neither the CPU nor the peripheral buses used have a concept of such.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It has some hackish code and it odd DMA results in the need to support
old features in kernel code.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Those boards do not need CONFIG_ISA if the ne driver could be
selectable without it. Disable it and update a defconfig.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.
The patch also does some whitespace cleanup.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch has removed 2 select entries for VR41xx.
These entries are selected in arch/mips/vr41xx/Kconfig.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has merged GT64111 PCI routines and GT64120 PCI_0 routines.
GT64111 PCI is almost the same as GT64120's PCI_0.
This patch don't change GT64120 PCI routines.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So until MIPS_MT_SMTC_INSTANT_REPLAY has been rewritten to solve this
issue, don't allow selecting it with PREEMPT.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Might be useful for SMP debugging.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[Rewritten Kconfig bits to deal better fit in the usual pattern of doing
things - Ralf]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A defconfig file and the 10 lines of code (including comments ...) that
are rotting since lmo commit 6516a42dc8b40c6c00010346dd51496125b16644
don't quite make proper support, so let's trash it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic rtc-ds1742 driver can be used for RBTX4927 and JMR3927
(with __swizzle_addr trick). This patch also removes MIPS local
DS1742 stuff.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds trivial support for SMARTMIPS extension. This extension
is currently implemented by 4KS[CD] CPUs.
Basically it saves/restores ACX register, which is part of the SMARTMIPS
ASE, when needed. This patch does *not* add any support for Smartmips MMU
features.
Futhermore this patch does not add explicit support for 4KS[CD] CPUs since
they are respectively mips32 and mips32r2 compliant. So with the current
processor configuration, a platform that has such CPUs needs to select
both configs:
CPU_HAS_SMARTMIPS
SYS_HAS_CPU_MIPS32_R[12]
This is due to the processor configuration which is mixing up all the
architecture variants and the processor types.
The drawback of this, is that we currently pass '-march=mips32' option to
gcc when building a kernel instead of '-march=4ksc' for 4KSC case. This
can lead to a kernel image a little bit bigger than required.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
