Commit Graph

51 Commits

Author SHA1 Message Date
Scott Wood
874d72c4fe mtd: elbc nand: use drvdata to only remove the relevant chip
Previously the remove method was looping and removing all chips,
which is obviously not the right thing to do — left over from when
the driver was organized differently and that was the remove method for
the entire controller.  This would result in bad things happening if
you have more than one NAND chip, and remove the module.

This also fixes priv->dev to properly point to the chip's device rather than
the controller's.  Until now priv->dev was only used for error/debug prints
(and it's an improvement there), so this shouldn't break anything.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06 18:17:05 +01:00
Brian Norris
1696e6bc2a mtd: nand: kill NAND_NO_READRDY
According to its documentation, the NAND_NO_READRDY option is always used
when autoincrement is not supported. Autoincrement support was recently
dropped, so we can drop this options as well (defaulting to "no read ready
check").

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06 18:17:05 +01:00
Brian Norris
d112dc7fa6 mtd: eLBC NAND: utilize oob_required parameter
Don't read OOB if the caller doesn't require it.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13 23:21:39 -05:00
Brian Norris
1fbb938dff mtd: nand: add 'oob_required' argument to NAND {read,write}_page interfaces
New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).

This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.

Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.

Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.

[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13 23:20:00 -05:00
Brian Norris
1826dbcceb mtd: nand: kill NAND_NO_AUTOINCR option
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13 23:15:38 -05:00
Mike Dunn
3f91e94f7f mtd: nand: read_page() returns max_bitflips
The ecc.read_page() method for nand drivers is changed to return the maximum
number of bitflips that were corrected on any one region covering an ecc step,
This patch doesn't change what the nand code returns to mtd.

This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹.

¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040883.html

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by (freescale changes): Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-05-13 23:12:06 -05:00
Mike Dunn
6a918bade9 mtd: flash drivers set ecc strength
Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the
maximum number of bit errors that can be corrected in one writesize region.

Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl,
which is the maximum number of bit errors that can be corrected in one ecc step.
Nand infrastructure code translates this to 'ecc_strength'.

Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc
modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE.  It is set in the
driver for all other modes.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-03-27 00:56:46 +01:00
Shengzhou Liu
f57eb5cc53 mtd: nand: Add ONFI support for FSL NAND controller
- fix NAND_CMD_READID command for ONFI detect.
- add NAND_CMD_PARAM command to read the ONFI parameter page.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:18:47 +00:00
Shengzhou Liu
d8251108e0 mtd: nand: fixup for fmr initialization of Freescale NAND controller
There was a bug for fmr initialization, which lead to  fmr was always 0x100
in fsl_elbc_chip_init() and caused FCM command timeout before calling
fsl_elbc_chip_init_tail(), now we initialize CWTO to maximum timeout value
and not relying on the setting of bootloader.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:18:44 +00:00
Liu Shuo
9ae84fe8c1 mtd: fsl_elbc_nand: set Nand flash page address to FBAR and FPAR correctly
If we use the Nand flash chip whose number of pages in a block is greater
than 64(for large page), we must treat the low bit of FBAR as being the
high bit of the page address due to the limitation of FCM, it simply uses
the low 6-bits (for large page) of the combined block/page address as the
FPAR component, rather than considering the actual block size.

Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:18:29 +00:00
Liu Shuo
e32de766c2 mtd: nand: set correct length to FBCR for a non-full-page write
When we do a non-full-page write, the length be set to FBCR should
not be 'elbc_fcm_ctrl->index', it should be 'elbc_fcm_ctrl->index -
elbc_fcm_ctrl->column'.

Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:13:18 +00:00
Liu Shuo
a9a552f0bf mtd: nand: use elbc_fcm_ctrl->oob to set FPAR_MS bit of FPAR
On both of large-page chip and small-page chip, we always should use
'elbc_fcm_ctrl->oob' to set the FPAR_LP_MS/FPAR_SP_MS bit of FPAR, don't
use a overflowed 'column' to set it.

Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:13:10 +00:00
Axel Lin
f99640dee2 mtd: convert drivers/mtd/* to use module_platform_driver()
This patch converts the drivers in drivers/mtd/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-01-09 18:12:35 +00:00
Michael Hench
f975c6bcb0 mtd: eLBC NAND: update ecc_stats.corrected when lteccr available
Signed-off-by: Michael Hench <MichaelHench@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11 15:02:17 +03:00
Mike Hench
52a474de0a mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly.  Remove this useless (and potentially problematic)
block of code.

Signed-off-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:15 +03:00
Liu Shuo
57b078a09b mtd: nand: don't free the global data too early
The global data fsl_lbc_ctrl_dev->nand don't have to be freed in
fsl_elbc_chip_remove(). The right place to do that is in fsl_elbc_nand_remove()
if elbc_fcm_ctrl->counter is zero.

Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:14 +03:00
Dmitry Eremin-Solenikov
99add4228f mtd: fsl_elbc_nand.c: use mtd_device_parse_register
Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:12 +03:00
Dmitry Eremin-Solenikov
b6b0fae717 mtd: fsl_elbc_nand: use ofpart through generic parsing
Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
2011-09-11 15:02:11 +03:00
Brian Norris
bb9ebd4e71 mtd: nand: rename NAND_USE_FLASH_BBT
Recall the recently added prefix requirements:
 * "NAND_" for flags in nand.h, used in nand_chip.options
 * "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options
        or in nand_bbt_descr.options

Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH.

Again, this flag is found in bbm.h and so should NOT be used in the
"nand_chip.options" field.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2011-09-11 15:01:56 +03:00
Brian Norris
a40f73419f mtd: nand: consolidate redundant flash-based BBT flags
This patch works with the following three flags from two headers (nand.h
and bbm.h):
  (1) NAND_USE_FLASH_BBT (nand.h)
  (2) NAND_USE_FLASH_BBT_NO_OOB (nand.h)
  (3) NAND_BBT_NO_OOB (bbm.h)

These flags are all related and interdependent, yet they were in
different headers. Flag (2) is simply the combination of (1) and (3) and
can be eliminated.

This patch accomplishes the following:
  * eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2))
  * move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h

It's important to note that because (1) and (3) are now both found in
bbm.h, they should NOT be used in the "nand_chip.options" field.

I removed a small section from the mtdnand DocBook because it referes to
NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2011-09-11 15:01:56 +03:00
Shaohui Xie
c02a02ee4d powerpc/85xx: fix NAND_CMD_READID read bytes number
when nand_get_flash_type() is called, it will read 8 bytes of ID instead of 5,
but the driver only read 5 bytes, so kernel will dump error messages like:

fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-06-22 06:08:48 -05:00
Jamie Iles
ed9281e60a mtd: fsl_elbc_nand: convert to mtd_device_register()
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-05-25 02:23:25 +01:00
Lucas De Marchi
25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Sergej.Stepanov@ids.de
eeda667a29 mtd: fsl_elbc_nand: fix jffs2 problem after NAND-flash image record in u-boot
This patch should fix the following problem:
 1. the  jffs2-image update in the u-boot was ok
 2. first restart and first mount of the NAND-flash-partition was also ok
 3. before the restart of controller there are no any activity on NAND-flash except of the jffs2_gcd_mtdX-process ...
 4. BUT after the second restart the NAND-flash-partition could not be really used after the second mount,
    dmesg filled with messages:
...
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03ce0000: 0xc0ff instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03d00000: 0xc0ff instead
....
Just for for info:
the behaviour observed on mpc8313-based board with the large-page NAND.
The only activity on NAND-flash was the garbage collector process, that looks for CLEANMARKER-nodes

As Scott said it was broken by commit 3ab8f2a2e7

Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-12-03 16:34:24 +00:00
Lan Chunhe-B25806
0b824d2b10 P4080/mtd: Fix the freescale lbc issue with 36bit mode
When system uses 36bit physical address, res.start is 36bit
physical address. But the function of in_be32 returns 32bit
physical address. Then both of them compared each other is
wrong. So by converting the address of res.start into
the right format fixes this issue.

Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-10-25 15:41:04 +01:00
Roy Zang
3ab8f2a2e7 P4080/eLBC: Make Freescale elbc interrupt common to elbc devices
Move Freescale elbc interrupt from nand driver to elbc driver.
Then all elbc devices can use the interrupt instead of ONLY nand.

For former nand driver, it had the two functions:

1. detecting nand flash partitions;
2. registering elbc interrupt.

Now, second function is removed to fsl_lbc.c.

Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-10-25 15:40:54 +01:00
Grant Likely
2dc1158137 of/device: Replace struct of_device with struct platform_device
of_device is just an alias for platform_device, so remove it entirely.  Also
replace to_of_device() with to_platform_device() and update comment blocks.

This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.

@@
@@
-struct of_device
+struct platform_device

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
2010-08-06 09:25:50 -06:00
Grant Likely
cf9b59e9d3 Merge remote branch 'origin' into secretlab/next-devicetree
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.

Conflicts:
	drivers/i2c/busses/i2c-cpm.c
	drivers/i2c/busses/i2c-mpc.c
	drivers/net/gianfar.c

Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-22 00:36:56 -06:00
Grant Likely
4018294b53 of: Remove duplicate fields from of_platform_driver
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver.  This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.

This patch is a pretty mechanical change.  The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial.  This patch looks big and scary because it touches so
many files, but it should be pretty safe.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
2010-05-22 00:10:40 -06:00
Grant Likely
61c7a080a5 of: Always use 'struct device.of_node' to get device node pointer.
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated.  This patch
makes all readers of these elements use device.of_node instead.

(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-18 16:10:44 -06:00
David Woodhouse
5e81e88a4c mtd: nand: Allow caller to pass alternative ID table to nand_scan_ident()
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-02-26 18:32:56 +00:00
H Hartley Sweeten
8a19b55818 mtd: fsl_elbc_nand.c: user resource_size()
Use resource_size().

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-12-31 19:53:51 +00:00
Scott Wood
c1317f7163 mtd: eLBC NAND: give more verbose output on error
We want error information even if the kernel hasn't been built for verbose
debugging.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-11-30 09:53:55 +00:00
Scott Wood
476459a6cf mtd: eLBC NAND: use recommended command sequences
Currently, the program and erase sequences do not wait for completion,
instead relying on a subsequent waitfunc() callback.  However, this causes
the chipselect to be deasserted while the NAND chip is still asserting the
busy pin, which can corrupt activity on other chipselects.

This patch switches to using the sequences recommended by the manual,
in which a wait is performed within the initial command sequence.  We can
now re-use the status byte from the initial command sequence, rather than
having to do another status read in the waitfunc.

Since we're already touching the command sequences, it also cleans up some
cruft in SEQIN that isn't needed since we cannot program partial pages
outside of OOB.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Suchit Lepcha <suchit.lepcha@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-11-30 09:53:49 +00:00
Scott Wood
b3a70f0bc3 mtd: eLBC NAND: increase bus timeout to maximum
When a NAND operation is in progress, all other localbus operations
(including NOR flash) will have to wait for access to the bus.  However, the
NAND operation may take longer to complete than the default timeout.  Thus,
if NOR is accessed while a NAND operation is in progress, the NAND operation
will fail.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-11-30 09:53:32 +00:00
Sneha Narnakaje
46a8cf2df2 mtd: nand: add "page" parameter to all read_page/read_page_raw APIs
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs.  The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.

Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-09-19 11:13:47 -07:00
Stephen Rothwell
4712fff9be powerpc: More printing warning fixes for the l64 to ll64 conversion
These are all powerpc specific drivers.

res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit.  Thanks to Scott Wood for noticing.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-28 17:15:52 +11:00
Jason Jin
03ed107805 [MTD] [NAND] Set the fsl elbc ECCM according the settings in bootloader.
The ECCM maybe set in bootloader, Get ECCM settings from the bootloader,
can avoid the image written by bootloader cannot read out by kernel.

But the limitation of doing it this way is that, it could break large page
NAND if it is written with NAND disabled in u-boot and read with NAND
enabled, or vice versa.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-10 16:44:28 +00:00
Sebastian Andrzej Siewior
69fd3a8d09 [MTD] remove unused mtd parameter in of_mtd_parse_partitions()
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-10-13 15:01:42 +01:00
akpm@linux-foundation.org
650da9d0b7 [MTD] [NAND] fsl_elbc_nand.c: fix printk warning
drivers/mtd/nand/fsl_elbc_nand.c:890: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-07-30 12:02:34 +01:00
Anton Vorontsov
55679df30d [MTD] [NAND] fsl_elbc_nand: fix section mismatch with CONFIG_MTD_OF_PARTS=y
With CONFIG_MTD_OF_PARTS=y I'm getting this new section mismatch in reference
from the function fsl_elbc_chip_probe() to the function
.devinit.text:of_mtd_parse_partitions()

This patch fixes the mismatch by providing __devinit annotation to the
fsl_elbc_chip_probe() function.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-07-25 09:43:54 -04:00
Anton Vorontsov
0acf944c68 [MTD] [NAND] fsl_elbc_nand: ecclayout cleanups
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.

Also remove mtd->ecclayout and mtd->oobavail assignments, mtd core
handles this all by itself.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-07-11 18:17:51 +01:00
Anton Vorontsov
ec6e0ea3bd [MTD] [NAND] fsl_elbc_nand: implement support for flash-based BBT
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.

Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-07-11 18:16:16 +01:00
Anton Vorontsov
452db27243 [MTD] [NAND] fsl_elbc_nand: fix OOB workability for large page NAND chips
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.

But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.

This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:

  OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
  OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
  OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
  OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.

To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-07-11 18:12:01 +01:00
Anton Vorontsov
aa83570e23 [MTD] [NAND] fsl_elbc_nand: fix section mismatch between probe and remove
WARNING: drivers/mtd/nand/built-in.o(.devinit.text+0x114): Section mismatch
in reference from the function fsl_elbc_ctrl_probe() to the function
.devexit.text:fsl_elbc_ctrl_remove()

__devinit functions should not call functions with __devexit. Since probe
function calls remove in case of errors, we want to remove __devexit
attribute from it.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-06-07 08:36:19 +01:00
Anton Vorontsov
0ff6631be1 [MTD] [NAND] fsl_elbc_nand: workaround for hangs during nand write
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22 21:13:53 +01:00
Mike Hench
1938de46cb [MTD] [NAND] corrected MPC8313 NAND fixes
Fix a race condition in fsl_elbc_run_command
Fix incorrect usage of clearbits32 that bashed option register
Remove work around for bashed register

Signed-off-by: Mike Hench <mhench@elutions.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22 20:52:09 +01:00
Anton Vorontsov
9ebed3e60f [MTD] [NAND] fsl_elbc_nand: fix mtd name
Currently fsl_elbc_nand doesn't initialize mtd->name, and this causes
nand_get_flash_type() to assign name that is equal to chip type, like
this:

   root@b1:~# cat /proc/mtd
   dev:    size   erasesize  name
   mtd0: 00800000 00010000 "fe000000.flash"
   mtd1: 02000000 00004000 "NAND 32MiB 3,3V 8-bit"

mtd0 is physmap_of flash (normal name), and mtd1 is fsl_elbc_nand.

Despite inconsistency, with mtd name like this specifying paritions
from the kernel command line becomes a torture (though, I didn't tried
and not sure if mtdparts= can handle spaces at all). Plus, this causes
real bugs when multiple fsl_elbc_nand chips registered.

With this patch applied fsl_elbc_nand chip will have proper name:

   root@b1:~# cat /proc/mtd
   dev:    size   erasesize  name
   mtd0: 00800000 00010000 "fe000000.flash"
   mtd1: 02000000 00004000 "e0600000.flash"

p.s. We can't use priv->dev->bus_id as in physmap_of, because
fsl_elbc_nand pretends to be a localbus controller, so its bus_id is
"address.localbus", which is incorrect and thus will also not work
for multiple chips.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22 20:50:31 +01:00
Scott Wood
576506645d [MTD] [NAND] fsl_elbc_nand: Fix SEQIN handling for large pages.
Previously, a READ command was erroneously issued rather than SEQIN.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22 15:36:24 +01:00
Anton Vorontsov
d4a32fe40a [POWERPC] fsl_elbc_nand: factor out localbus defines
This is needed to support other localbus peripherals, such as
NAND on FSL UPM.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-17 01:01:38 -05:00