If clk_enable() fails, then print a message so that the user can see
what is happening instead of silently failing to enable the clock.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The clk_enable() call in the pm_clk_resume() call returns an error
that is not being checked. If clk_enable() fails then we should
not set the state of the clock to PCE_STATUS_ENABLED.
Note, the issue of warning the user if this fails has not been
addressed in this patch as this is not the only place the driver
calls clk_enable().
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The drivers/base/power/clock_ops.c file is causing warnings from
the clock driver (as shown below) due to failing to do a clk_prepare()
call before enabling a clock. It also fails to check the balance of
prepare/unprepare as __pm_clk_remove() do clk_disable_unprepare() call.
This bug has probably been in since commit b2476490e ("clk: introduce
the common clock framework") as the warning was part of the original
commit. It is strange that it has not been noticed (although this has
also been coupled with a failure for certain SH builds to not build the
necessary glue to use this method of controlling the clocks).
In summary, this is probably needed in several stable branches but need
advice on which ones.
On the Renesas Lager board, this causes numerous warnings of the following
and even worse the clock system will not enable clocks, causing drivers
that are in development to fail to work:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:883 __clk_enable+0x2c/0xa0()
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pm_generic_runtime_suspend|resume functions were implemented within
CONFIG_PM_RUNTIME.
As we also may use runtime PM callbacks during system suspend, to put
devices into low power state, we need to move the implementation of
pm_generic_runtime_suspend|resume to CONFIG_PM.
This change gives a power domain provision to invoke a platform
driver's runtime PM callback from a power domain's system PM callback.
This were earlier prevented by the platform bus, since it uses the
pm_generic_runtime_suspend|resume functions as runtime PM callbacks.
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 5a87182aa2 (cpufreq: suspend governors on system
suspend/hibernate) causes hibernation problems to happen on
Bjørn Mork's and Paul Bolle's systems, so revert it.
Fixes: 5a87182aa2 (cpufreq: suspend governors on system suspend/hibernate)
Reported-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpuidle:
cpuidle: Check for dev before deregistering it.
intel_idle: Fixed C6 state on Avoton/Rangeley processors
* pm-cpufreq:
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
This patch adds cpufreq suspend/resume calls to dpm_{suspend|resume}_noirq()
for handling suspend/resume of cpufreq governors.
Lan Tianyu (Intel) & Jinhyuk Choi (Broadcom) found anr issue where
tunables configuration for clusters/sockets with non-boot CPUs was
getting lost after suspend/resume, as we were notifying governors
with CPUFREQ_GOV_POLICY_EXIT on removal of the last cpu for that
policy and so deallocating memory for tunables. This is fixed by
this patch as we don't allow any operation on governors after
device suspend and before device resume now.
Reported-and-tested-by: Lan Tianyu <tianyu.lan@intel.com>
Reported-by: Jinhyuk Choi <jinchoi@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog, minor cleanups]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a device prepare callback for some reason would fail, the PM core
prevented the device from going inactive forever.
In this case, to reverse the pm_runtime_get_noresume() we invokes the
asyncronous pm_runtime_put(), thus restoring the usage count.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq: (167 commits)
cpufreq: create per policy rwsem instead of per CPU cpu_policy_rwsem
intel_pstate: Add Baytrail support
intel_pstate: Refactor driver to support CPUs with different MSR layouts
cpufreq: Implement light weight ->target_index() routine
PM / OPP: rename header to linux/pm_opp.h
PM / OPP: rename data structures to dev_pm equivalents
PM / OPP: rename functions to dev_pm_opp*
cpufreq / governor: Remove fossil comment
cpufreq: exynos4210: Use the common clock framework to set APLL clock rate
cpufreq: exynos4x12: Use the common clock framework to set APLL clock rate
cpufreq: Detect spurious invocations of update_policy_cpu()
cpufreq: pmac64: enable cpufreq on iMac G5 (iSight) model
cpufreq: pmac64: provide cpufreq transition latency for older G5 models
cpufreq: pmac64: speed up frequency switch
cpufreq: highbank-cpufreq: Enable Midway/ECX-2000
exynos-cpufreq: fix false return check from "regulator_set_voltage"
speedstep-centrino: Remove unnecessary braces
acpi-cpufreq: Add comment under ACPI_ADR_SPACE_SYSTEM_IO case
cpufreq: arm-big-little: use clk_get instead of clk_get_sys
cpufreq: exynos: Show a list of available frequencies
...
Conflicts:
drivers/devfreq/exynos/exynos5_bus.c
Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename opp_* data
structures in OPP library with dev_pm_opp_* equivalent.
Affected structures are:
struct opp
enum opp_event
Minor checkpatch warning resulting of this change was fixed as well.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.
Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rather than hard-lock the kernel, dump the suspend/resume thread stack
and panic() to capture a message in pstore when a driver takes too long
to suspend/resume. Default suspend/resume watchdog timeout is set to 12
seconds to be longer than the usbhid 10 second timeout, but could be
changed at compile time.
Exclude from the watchdog the time spent waiting for children that
are resumed asynchronously and time every device, whether or not they
resumed synchronously.
This patch is targeted for mobile devices where a suspend/resume lockup
could cause a system reboot. Information about failing device can be
retrieved in subsequent boot session by mounting pstore and inspecting
the log. Laptops with EFI-enabled pstore could also benefit from
this feature.
The hardware watchdog timer is likely suspended during this time and
couldn't be relied upon. The soft-lockup detector would eventually tell
that tasks are not scheduled, but would provide little context as to why.
The patch hence uses system timer and assumes it is still active while the
devices are suspended/resumed.
This feature can be enabled/disabled during kernel configuration.
This change is based on earlier work by San Mehat.
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For devices which don't have a .runtime_idle() callback or if it
returns 0, rpm_idle() will end up in triggering a call to
rpm_suspend(), thus trying to carry out a runtime suspend directly
from runtime_idle().
In the above situation we want to respect devices which has enabled
autosuspend, we therfore append the flag sent to rpm_suspend with
RPM_AUTO.
Do note that drivers still needs to update the device last busy mark,
to control the delay for this circumstance.
Updated runtime PM documentation accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=CgqW
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
* tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (217 commits)
cpufreq: Don't use smp_processor_id() in preemptible context
cpuidle: coupled: fix race condition between pokes and safe state
cpuidle: coupled: abort idle if pokes are pending
cpuidle: coupled: disable interrupts after entering safe state
ACPI / hotplug: Remove containers synchronously
driver core / ACPI: Avoid device hot remove locking issues
cpufreq: governor: Fix typos in comments
cpufreq: governors: Remove duplicate check of target freq in supported range
cpufreq: Fix timer/workqueue corruption due to double queueing
ACPI / EC: Add ASUSTEK L4R to quirk list in order to validate ECDT
ACPI / thermal: Add check of "_TZD" availability and evaluating result
cpufreq: imx6q: Fix clock enable balance
ACPI: blacklist win8 OSI for buggy laptops
cpufreq: tegra: fix the wrong clock name
cpuidle: Change struct menu_device field types
cpuidle: Add a comment warning about possible overflow
cpuidle: Fix variable domains in get_typical_interval()
cpuidle: Fix menu_device->intervals type
cpuidle: CodingStyle: Break up multiple assignments on single line
cpuidle: Check called function parameter in get_typical_interval()
...
Export opp_add() so that modules can use it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A new trace event is added to PM events to print the time it takes to
suspend and resume a device. It generates trace messages that
include device, driver, parent information in addition to the type of
PM ops invoked as well as the PM event and error status from the PM
ops. Example trace below:
bash-2239 [000] .... 290.883035: device_pm_report_time: backlight
acpi_video0 parent=0000:00:02.0 state=freeze ops=class nsecs=332 err=0
bash-2239 [000] .... 290.883041: device_pm_report_time: rfkill rf
kill3 parent=phy0 state=freeze ops=legacy class nsecs=216 err=0
bash-2239 [001] .... 290.973892: device_pm_report_time: ieee80211
phy0 parent=0000:01:00.0 state=freeze ops=legacy class nsecs=90846477 err=0
bash-2239 [001] .... 293.660129: device_pm_report_time: ieee80211 phy0 parent=0000:01:00.0 state=restore ops=legacy class nsecs=101295162 err=0
bash-2239 [001] .... 293.660147: device_pm_report_time: rfkill rfkill3 parent=phy0 state=restore ops=legacy class nsecs=1804 err=0
bash-2239 [001] .... 293.660157: device_pm_report_time: backlight acpi_video0 parent=0000:00:02.0 state=restore ops=class nsecs=757 err=0
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds tracepoints to dev_pm_qos_add_request, dev_pm_qos_update_request,
and dev_pm_qos_remove_request. It's useful for checking device name,
dev_pm_qos_request_type, and value.
Signed-off-by: Sahara <keun-o.park@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit a938da06 introduced a useful little log message to tell
users/debuggers which wakeup source aborted a suspend. However,
this message is only printed if the abort happens during the
in-kernel suspend path (after writing /sys/power/state).
The full specification of the /sys/power/wakeup_count facility
allows user-space power managers to double-check if wakeups have
already happened before it actually tries to suspend (e.g. while it
was running user-space pre-suspend hooks), by writing the last known
wakeup_count value to /sys/power/wakeup_count. This patch changes
the sysfs handler for that node to also print said log message if
that write fails, so that we can figure out the offending wakeup
source for both kinds of suspend aborts.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds in a new message to the wakeup code which adds an
indication to the log that suspend was cancelled due to a wake event
occouring during the suspend sequence. It also adjusts the message
printed in suspend.c to reflect the potential that a suspend was
aborted, as opposed to a device failing to suspend.
Without these message adjustments one can end up with a kernel log
that says that a device failed to suspend with no actual device
suspend failures, which can be confusing to the log examiner.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "index" field of struct cpufreq_frequency_table was never an
index and isn't used at all by the cpufreq core. It only is useful
for cpufreq drivers for their internal purposes.
Many people nowadays blindly set it in ascending order with the
assumption that the core will use it, which is a mistake.
Rename it to "driver_data" as that's what its purpose is. All of its
users are updated accordingly.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Fix dev_pm_put_subsys_data() so that it doesn't call kfree() under
a spinlock and make it return 1 whenever it leaves NULL
power.subsys_data (regardless of the reason).
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-assorted:
PM / OPP: add documentation to RCU head in struct opp
PM / sleep: invalidate TEST_CPUS and TEST_CORE support for freeze state
PM / sleep: add TEST_PLATFORM support for freeze state
When genpd prepares for a system suspend it will fetch a runtime
reference for the device. When returning it we now use the
asyncronous runtime PM API. Thus we don't have to wait for the
device to become idle|suspended before we move on and handle the
next device in queue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For irq safe devices return the runtime reference for the parent
by using the asyncronous runtime PM API. Thus we don't have to
wait for it to become idle|suspended. Instead we can move on and
handle the next device in queue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the asyncronous runtime PM API when returning the runtime
reference for the device after the system resume is completed.
By using the asyncronous runtime PM API we don't have to wait
for each an every device to become idle|suspended. Instead we
can move on and handle the next device in queue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit dde8437 (PM / OPP: RCU reclaim) introduced rcu_head for
struct opp. This aids freeing using kfree_rcu. However, we missed
adding documentation for the same. This generates kernel doc warning:
Warning(drivers/base/power/opp.c:70): No description found for
parameter 'head'
Add documentation as appropriate.
[rjw: Changelog]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit b81ea1b (PM / QoS: Fix concurrency issues and memory leaks in
device PM QoS) put calls to pm_qos_sysfs_add_latency(),
pm_qos_sysfs_add_flags(), pm_qos_sysfs_remove_latency(), and
pm_qos_sysfs_remove_flags() under dev_pm_qos_mtx, which was a
mistake, because it may lead to deadlocks in some situations.
For example, if pm_qos_remote_wakeup_store() is run in parallel
with dev_pm_qos_constraints_destroy(), they may deadlock in the
following way:
======================================================
[ INFO: possible circular locking dependency detected ]
3.9.0-rc4-next-20130328-sasha-00014-g91a3267 #319 Tainted: G W
-------------------------------------------------------
trinity-child6/12371 is trying to acquire lock:
(s_active#54){++++.+}, at: [<ffffffff81301631>] sysfs_addrm_finish+0x31/0x60
but task is already holding lock:
(dev_pm_qos_mtx){+.+.+.}, at: [<ffffffff81f07cc3>] dev_pm_qos_constraints_destroy+0x23/0x250
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (dev_pm_qos_mtx){+.+.+.}:
[<ffffffff811811da>] lock_acquire+0x1aa/0x240
[<ffffffff83dab809>] __mutex_lock_common+0x59/0x5e0
[<ffffffff83dabebf>] mutex_lock_nested+0x3f/0x50
[<ffffffff81f07f2f>] dev_pm_qos_update_flags+0x3f/0xc0
[<ffffffff81f05f4f>] pm_qos_remote_wakeup_store+0x3f/0x70
[<ffffffff81efbb43>] dev_attr_store+0x13/0x20
[<ffffffff812ffdaa>] sysfs_write_file+0xfa/0x150
[<ffffffff8127f2c1>] __kernel_write+0x81/0x150
[<ffffffff812afc2d>] write_pipe_buf+0x4d/0x80
[<ffffffff812af57c>] splice_from_pipe_feed+0x7c/0x120
[<ffffffff812afa25>] __splice_from_pipe+0x45/0x80
[<ffffffff812b14fc>] splice_from_pipe+0x4c/0x70
[<ffffffff812b1538>] default_file_splice_write+0x18/0x30
[<ffffffff812afae3>] do_splice_from+0x83/0xb0
[<ffffffff812afb2e>] direct_splice_actor+0x1e/0x20
[<ffffffff812b0277>] splice_direct_to_actor+0xe7/0x200
[<ffffffff812b15bc>] do_splice_direct+0x4c/0x70
[<ffffffff8127eda9>] do_sendfile+0x169/0x300
[<ffffffff8127ff94>] SyS_sendfile64+0x64/0xb0
[<ffffffff83db7d18>] tracesys+0xe1/0xe6
-> #0 (s_active#54){++++.+}:
[<ffffffff811800cf>] __lock_acquire+0x15bf/0x1e50
[<ffffffff811811da>] lock_acquire+0x1aa/0x240
[<ffffffff81300aa2>] sysfs_deactivate+0x122/0x1a0
[<ffffffff81301631>] sysfs_addrm_finish+0x31/0x60
[<ffffffff812ff77f>] sysfs_hash_and_remove+0x7f/0xb0
[<ffffffff813035a1>] sysfs_unmerge_group+0x51/0x70
[<ffffffff81f068f4>] pm_qos_sysfs_remove_flags+0x14/0x20
[<ffffffff81f07490>] __dev_pm_qos_hide_flags+0x30/0x70
[<ffffffff81f07cd5>] dev_pm_qos_constraints_destroy+0x35/0x250
[<ffffffff81f06931>] dpm_sysfs_remove+0x11/0x50
[<ffffffff81efcf6f>] device_del+0x3f/0x1b0
[<ffffffff81efd128>] device_unregister+0x48/0x60
[<ffffffff82d4083c>] usb_hub_remove_port_device+0x1c/0x20
[<ffffffff82d2a9cd>] hub_disconnect+0xdd/0x160
[<ffffffff82d36ab7>] usb_unbind_interface+0x67/0x170
[<ffffffff81f001a7>] __device_release_driver+0x87/0xe0
[<ffffffff81f00559>] device_release_driver+0x29/0x40
[<ffffffff81effc58>] bus_remove_device+0x148/0x160
[<ffffffff81efd07f>] device_del+0x14f/0x1b0
[<ffffffff82d344f9>] usb_disable_device+0xf9/0x280
[<ffffffff82d34ff8>] usb_set_configuration+0x268/0x840
[<ffffffff82d3a7fc>] usb_remove_store+0x4c/0x80
[<ffffffff81efbb43>] dev_attr_store+0x13/0x20
[<ffffffff812ffdaa>] sysfs_write_file+0xfa/0x150
[<ffffffff8127f71d>] do_loop_readv_writev+0x4d/0x90
[<ffffffff8127f999>] do_readv_writev+0xf9/0x1e0
[<ffffffff8127faba>] vfs_writev+0x3a/0x60
[<ffffffff8127fc60>] SyS_writev+0x50/0xd0
[<ffffffff83db7d18>] tracesys+0xe1/0xe6
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(dev_pm_qos_mtx);
lock(s_active#54);
lock(dev_pm_qos_mtx);
lock(s_active#54);
*** DEADLOCK ***
To avoid that, remove the calls to functions mentioned above from
under dev_pm_qos_mtx and introduce a separate lock to prevent races
between functions that add or remove device PM QoS sysfs attributes
from happening.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Device PM QoS sysfs attributes, if present during device removal,
are removed from within device_pm_remove(), which is too late,
since dpm_sysfs_remove() has already removed the whole attribute
group they belonged to. However, moving the removal of those
attributes to dpm_sysfs_remove() alone is not sufficient, because
in theory they still can be re-added right after being removed by it
(the device's driver is still bound to it at that point).
For this reason, move the entire desctruction of device PM QoS
constraints to dpm_sysfs_remove() and make it prevent any new
constraints from being added after it has run. Also, move the
initialization of the power.qos field in struct device to
device_pm_init_common() and drop the no longer needed
dev_pm_qos_constraints_init().
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current device PM QoS code assumes that certain functions will
never be called in parallel with each other (for example, it is
assumed that dev_pm_qos_expose_flags() won't be called in parallel
with dev_pm_qos_hide_flags() for the same device and analogously
for the latency limit), which may be overly optimistic. Moreover,
dev_pm_qos_expose_flags() and dev_pm_qos_expose_latency_limit()
leak memory in error code paths (req needs to be freed on errors)
and __dev_pm_qos_drop_user_request() forgets to free the request.
To fix the above issues put more things under the device PM QoS
mutex to make them mutually exclusive and add the missing freeing
of memory.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Apply the introduced memalloc_noio_save() and memalloc_noio_restore() to
force memory allocation with no I/O during runtime_resume/runtime_suspend
callback on device with the flag of 'memalloc_noio' set.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Jiri Kosina <jiri.kosina@suse.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce the flag memalloc_noio in 'struct dev_pm_info' to help PM core
to teach mm not allocating memory with GFP_KERNEL flag for avoiding
probable deadlock.
As explained in the comment, any GFP_KERNEL allocation inside
runtime_resume() or runtime_suspend() on any one of device in the path
from one block or network device to the root device in the device tree
may cause deadlock, the introduced pm_runtime_set_memalloc_noio() sets
or clears the flag on device in the path recursively.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Jiri Kosina <jiri.kosina@suse.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZ/kACgkQMUfUDdst+ylEhwCgyM0JEOgLuW7M8D+oNcitZn51
g7oAniD0IkLG8RCB8plLj+82AvthalCo
=bHSs
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday."
* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (190 commits)
Revert "USB: EHCI: make ehci-vt8500 a separate driver"
Revert "USB: EHCI: make ehci-orion a separate driver"
Revert "USB: update host controller Kconfig entries"
USB: update host controller Kconfig entries
USB: EHCI: make ehci-orion a separate driver
USB: EHCI: make ehci-vt8500 a separate driver
USB: usb-storage: unusual_devs update for Super TOP SATA bridge
USB: ehci-omap: Fix autoloading of module
USB: ehci-omap: Don't free gpios that we didn't request
USB: option: add Huawei "ACM" devices using protocol = vendor
USB: serial: fix null-pointer dereferences on disconnect
USB: option: add Yota / Megafon M100-1 4g modem
drivers/usb: add missing GENERIC_HARDIRQS dependencies
USB: storage: properly handle the endian issues of idProduct
testusb: remove all mentions of 'usbfs'
usb: gadget: imx_udc: make it depend on BROKEN
usb: omap_control_usb: fix compile warning
ARM: OMAP: USB: Add phy binding information
ARM: OMAP2: MUSB: Specify omap4 has mailbox
ARM: OMAP: devices: create device for usb part of control module
...
* pm-cpufreq: (55 commits)
cpufreq / intel_pstate: Fix 32 bit build
cpufreq: conservative: Fix typos in comments
cpufreq: ondemand: Fix typos in comments
cpufreq: exynos: simplify .init() for setting policy->cpus
cpufreq: kirkwood: Add a cpufreq driver for Marvell Kirkwood SoCs
cpufreq/x86: Add P-state driver for sandy bridge.
cpufreq_stats: do not remove sysfs files if frequency table is not present
cpufreq: Do not track governor name for scaling drivers with internal governors.
cpufreq: Only call cpufreq_out_of_sync() for driver that implement cpufreq_driver.target()
cpufreq: Retrieve current frequency from scaling drivers with internal governors
cpufreq: Fix locking issues
cpufreq: Create a macro for unlock_policy_rwsem{read,write}
cpufreq: Remove unused HOTPLUG_CPU code
cpufreq: governors: Fix WARN_ON() for multi-policy platforms
cpufreq: ondemand: Replace down_differential tuner with adj_up_threshold
cpufreq / stats: Get rid of CPUFREQ_STATDEVICE_ATTR
cpufreq: Don't check cpu_online(policy->cpu)
cpufreq: add imx6q-cpufreq driver
cpufreq: Don't remove sysfs link for policy->cpu
cpufreq: Remove unnecessary use of policy->shared_type
...
PM_SUSPEND_FREEZE state is a general state that
does not need any platform specific support, it equals
frozen processes + suspended devices + idle processors.
Compared with PM_SUSPEND_MEMORY,
PM_SUSPEND_FREEZE saves less power
because the system is still in a running state.
PM_SUSPEND_FREEZE has less resume latency because it does not
touch BIOS, and the processors are in idle state.
Compared with RTPM/idle,
PM_SUSPEND_FREEZE saves more power as
1. the processor has longer sleep time because processes are frozen.
The deeper c-state the processor supports, more power saving we can get.
2. PM_SUSPEND_FREEZE uses system suspend code path, thus we can get
more power saving from the devices that does not have good RTPM support.
This state is useful for
1) platforms that do not have STR, or have a broken STR.
2) platforms that have an extremely low power idle state,
which can be used to replace STR.
The following describes how PM_SUSPEND_FREEZE state works.
1. echo freeze > /sys/power/state
2. the processes are frozen.
3. all the devices are suspended.
4. all the processors are blocked by a wait queue
5. all the processors idles and enters (Deep) c-state.
6. an interrupt fires.
7. a processor is woken up and handles the irq.
8. if it is a general event,
a) the irq handler runs and quites.
b) goto step 4.
9. if it is a real wake event, say, power button pressing, keyboard touch, mouse moving,
a) the irq handler runs and activate the wakeup source
b) wakeup_source_activate() notifies the wait queue.
c) system starts resuming from PM_SUSPEND_FREEZE
10. all the devices are resumed.
11. all the processes are unfrozen.
12. system is back to working.
Known Issue:
The wakeup of this new PM_SUSPEND_FREEZE state may behave differently
from the previous suspend state.
Take ACPI platform for example, there are some GPEs that only enabled
when the system is in sleep state, to wake the system backk from S3/S4.
But we are not touching these GPEs during transition to PM_SUSPEND_FREEZE.
This means we may lose some wake event.
But on the other hand, as we do not disable all the Interrupts during
PM_SUSPEND_FREEZE, we may get some extra "wakeup" Interrupts, that are
not available for S3/S4.
The patches has been tested on an old Sony laptop, and here are the results:
Average Power:
1. RPTM/idle for half an hour:
14.8W, 12.6W, 14.1W, 12.5W, 14.4W, 13.2W, 12.9W
2. Freeze for half an hour:
11W, 10.4W, 9.4W, 11.3W 10.5W
3. RTPM/idle for three hours:
11.6W
4. Freeze for three hours:
10W
5. Suspend to Memory:
0.5~0.9W
Average Resume Latency:
1. RTPM/idle with a black screen: (From pressing keyboard to screen back)
Less than 0.2s
2. Freeze: (From pressing power button to screen back)
2.50s
3. Suspend to Memory: (From pressing power button to screen back)
4.33s
>From the results, we can see that all the platforms should benefit from
this patch, even if it does not have Low Power S0.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export cpufreq helpers in OPP to make the cpufreq-core0 and highbank-cpufreq
drivers loadable as modules.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We are GPLV2 library, so be clear in the symbols exported as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There's no need to test whether a (delayed) work item is pending
before queueing, flushing or cancelling it, so remove work_pending()
tests used in those cases.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dev_pm_qos_flags() will be used in the usb core which could be
compiled as a module. This patch is to export it.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the PM core disables runtime PM for all devices right
after executing subsystem/driver .suspend() callbacks for them
and re-enables it right before executing subsystem/driver .resume()
callbacks for them. This may lead to problems when there are
two devices such that the .suspend() callback executed for one of
them depends on runtime PM working for the other. In that case,
if runtime PM has already been disabled for the second device,
the first one's .suspend() won't work correctly (and analogously
for resume).
To make those issues go away, make the PM core disable runtime PM
for devices right before executing subsystem/driver .suspend_late()
callbacks for them and enable runtime PM for them right after
executing subsystem/driver .resume_early() callbacks for them. This
way the potential conflitcs between .suspend_late()/.resume_early()
and their runtime PM counterparts are still prevented from happening,
but the subtle ordering issues related to disabling/enabling runtime
PM for devices during system suspend/resume are much easier to avoid.
Reported-and-tested-by: Jan-Matthias Braun <jan_braun@gmx.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: 3.4+ <stable@vger.kernel.org>
