Commit Graph

90 Commits

Author SHA1 Message Date
Hans Verkuil
23fb4c5ea1 [media] bttv: embed video_device
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-04-08 06:45:12 -03:00
Ondrej Zary
35655bf854 [media] bttv: Improve TEA575x support
Improve g_tuner and add s_hw_freq_seek and enum_freq_bands support for cards
with TEA575x radio.

This allows signal/stereo detection and HW seek to work on these cards.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-01-27 10:14:20 -02:00
Ondrej Zary
1b50037315 [media] bttv: Convert to generic TEA575x interface
Remove tea575x-specific code from bttv and use the common driver instead.

Only set_frequency is implemented (signal/stereo detection or seek would
require more changes to bttv).

It works fine on Video Highway Xtreme (it actually makes the radio usable as
it currently cannot be tuned properly).

Miro/Pinnacle is untested but seems to be simple and should work.

However, I don't understand the Terratec Active Radio Upgrade code. The HW
seems to need IOR, IOW and CSEL signals that were taken from ISA bus on
older cards (IOR and IOW directly and CSEL from some address decoder) and
are emulated here using GPIOs. But the code manipulating these signals in
bttv seems to be broken - it never asserts the IOR signal. If anyone has
this HW, please test if I got that right.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-01-27 10:13:19 -02:00
Hans Verkuil
21a7e0596a [media] media: drivers shouldn't touch debug field in video_device
The debug field in struct video_device is for internal use only and
drivers should mix that with their own debug module options.

It is handled by the V4L2 core and users can set it using
/sys/class/video4linux/<devX>/debug.

It has been deprecated for some time now, so it is time to remove it
completely from the drivers.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 10:29:04 -02:00
Hans Verkuil
90ca8bef90 [media] btcx-risc: move to bt8xx
The btcx-risc module is no longer used by other drivers except for bttv.
So move it from common to bt8xx and make it part of the bttv driver instead
of as a separate module.

This module should never have been a common module since most of the code
has always been bttv specific.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-23 10:13:19 -02:00
Hans Verkuil
215cedec37 [media] media: remove emacs editor variables
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-12-22 17:52:20 -02:00
Hans Verkuil
872dfcfe82 [media] bttv/cx25821/cx88/ivtv: use sg_next instead of sg++
Never use sg++, always use sg = sg_next(sg). Scatterlist entries can
be combined if the memory is contiguous but sg++ won't know about that.

As far as I can tell cx88 and ivtv are really broken because of this,
and bttv and cx25821 are OK because vb1 doesn't combine scatterlist
entries.

But regardless, sg++ should never be used, only sg_next is safe.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-25 08:12:53 -02:00
Hans Verkuil
cf38d4b92d [media] bttv: fix sparse warning
bttv-cards.c:3874:55: warning: incorrect type in initializer (different base types)

Also clean up the code a little by adding spaces.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2014-11-05 09:07:19 -02:00
Mauro Carvalho Chehab
a896dc7a1f [media] bt8xx: just return 0 instead of using a var
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:29 -03:00
Mauro Carvalho Chehab
c3142a61e6 [media] bttv-driver: remove an uneeded semicolon
We don't use semicolons after curly braces in the middle of the
code.

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-09-03 17:59:12 -03:00
Joe Perches
6850aeabdd media: use pci_zalloc_consistent
Remove the now unnecessary memset too.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-08 15:57:28 -07:00
David Härdeman
120703f9eb [media] rc-core: document the protocol type
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.

This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.

[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-07-23 21:50:48 -03:00
David Härdeman
4dd9bb91bb [media] rc-core: improve ir-kbd-i2c get_key functions
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.

Convert all of them to return a protocol/scancode/toggle triple instead.

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-07-23 20:05:56 -03:00
David Härdeman
2886f013c3 [media] bt8xx: fixup RC5 decoding
The bt8xx driver does RC5 decoding for Nebula digi hardware, but includes
some pointless limitations (both start bits must be one, the
device/address/system must be 0x00). Remove those limitations and update
the keymap to use the full RC5 scancode (fortunately the 0x00 address
means that this is perfectly backwards compatible).

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-07-23 20:01:23 -03:00
Ramakrishnan Muthukrishnan
95cd5d5ee6 [media] media: remove the setting of the flag V4L2_FL_USE_FH_PRIO
Since all the drivers that use `struct v4l2_fh' use the core
priority checking, the setting of the flag in the drivers can
be removed.

Signed-off-by: Ramakrishnan Muthukrishnan <ramakrmu@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-07-04 16:14:59 -03:00
Laurent Pinchart
8774bed9ce [media] v4l: subdev: Move [gs]_std operation to video ops
The g_std and s_std operations are video-related, move them to the video
ops where they belong.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-05-24 17:11:26 -03:00
Luis R. Rodriguez
68592773e3 [media] bt8xx: make driver routines fit into its own namespcae
There is a few conflicts with older symbols on older kernels so we
have to patch this driver when backporting. Instead just make these
routines specific to the driver.

Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-05-23 19:48:12 -03:00
Daniel Glöckner
c8204930b2 [media] bttv: Add support for PCI-8604PW
This patch adds support for the PCI-8604PW card equipped with four 878A.
It is unknown who the manufacturer of this card is and no drivers were
available during development of the patch. According to images found
online, the card is originally sold with Linux DVR software.

A CPLD on the card prevents the 878A from requesting access to the
bus until an initialization sequence has been issued via GPIOs. The
implemented sequence uses the minimum number of GPIOs needed to
successfully unlock bus access. As there are many more GPIOs connected
to the CPLD, it is very likely that some of the others have an influence
on the bus arbitration scheduling. This should be investigated further
in case of performance issues.

The tested card contains an EEPROM on one of the 878A, but it is
completely empty (i.e. contains only 0xff), so it is not possible
to detect the card.

Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Tested-by: Robert Longbottom <rongblor@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-04-16 18:22:48 -03:00
Pojar George
493a9cfdb9 [media] bttv: Add support for Kworld V-Stream Xpert TV PVR878
New board addition. No other changes.

[m.chehab@samsung.com: rebase patch and fix whitespace mangling]
Signed-off-by: Pojar George <geoubuntu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-03-11 11:40:31 -03:00
Michael Krufky
08e1097266 [media] update Michael Krufky's email address
I am no longer available at the kernellabs.com or m1k.net email
addresses.  Update each instance of my email to my linuxtv.org
account.

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-02-04 06:34:21 -02:00
Levente Kurusa
38121b6ef3 [media] media: bt8xx: add missing put_device call
This is required so that we give up the last reference to the device.
Remove the kfree() because the put_device() call will actually call
release_sub_device which in turn kfrees the device.

Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-02-04 06:27:38 -02:00
Ricardo Ribalda
f90580ca01 [media] videodev2: Set vb2_rect's width and height as unsigned
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.

Therefore this patch is an attempt to convert those fields from __s32 to
__u32.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07 08:02:39 -02:00
Hans Verkuil
09092787e0 [media] saa6588: add support for non-blocking mode
saa6588 always blocked while waiting for data, even if the filehandle
was in non-blocking mode.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07 07:42:19 -02:00
Hans Verkuil
f8e1b699a5 [media] bttv: don't setup the controls if there are no video devices
The no_video flag was checked in all other cases except one. Calling
v4l2_ctrl_handler_setup() if no_video is 1 will crash.
This wasn't noticed before since there are only two card types that
set no_video to 1, so this type of hardware is quite rare.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lorenz Röhrl <sheepshit@gmx.de>
Tested-by: Lorenz Röhrl <sheepshit@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2013-11-29 14:18:33 -02:00
Michael Opdenacker
3e018fe440 [media] misc drivers: remove deprecated IRQF_DISABLED
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2013-10-17 06:08:31 -03:00
Sachin Kamat
b17a87be20 [media] pci: bt878: Remove redundant pci_set_drvdata
Driver core sets driver data to NULL upon failure or remove.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2013-10-17 06:03:48 -03:00
Ondrej Zary
cd2e34ead8 [media] bttv: stop abusing mbox_we for sw_status
Kodicom 4400R and Geovision GV-800 code in bttv driver abuses mbox_we (int)
in struct bttv as char *.
Remove this hack and add a proper sw_status array to struct bttv instead.
This is a a preparation to remove mbox_we.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2013-07-26 13:33:10 -03:00
Hans Verkuil
0bde6c3e4c [media] bttv: fix querystd
AND the standard mask with the detected standards.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-06-17 09:44:40 -03:00
Hans Verkuil
abca2056dc [media] v4l2: remove g_chip_ident from bridge drivers where it is easy to do so
VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-06-17 08:36:35 -03:00
Lad, Prabhakar
7eac97d7e7 [media] media: pci: remove duplicate checks for EPERM
This patch removes check for EPERM in dbg_g/s_register and
vidioc_g/s_register as this check is already performed by core.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-05-27 09:34:56 -03:00
Hans Verkuil
05ff7240b0 [media] CARDLIST.bttv: add new cards
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-05-21 08:16:02 -03:00
Ondrej Zary
ba9948fb9c [media] bttv: Add CyberVision CV06
Add CyberVision CV06 4-camera card (from CyberVision SV card kit):
http://www.cybervision.com.tw/products-swcard_kits-sv.html
There are some interesting things on the card but they're not supported:
4 LEDs, a connector with 4 IN and 4 OUT pins, RESET IN and RESET OUT
connectors, a relay and CyberVision CV8088-SV16 chip

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-05-21 08:12:53 -03:00
Ondrej Zary
ec7c15b58f [media] bttv: Add noname Bt848 capture card with 14MHz xtal
Add support for noname Bt848 capture-only card (3x composite, 1x S-VHS)
with 14MHz crystal:
http://www.rainbow-software.org/images/hardware/bt848_.jpg
14MHz PLL was not supported by bttv driver until now.

[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-05-21 08:12:19 -03:00
Hans Verkuil
835ab0121a [media] bttv: Add Adlink MPG24 entry to the bttv cardlist
Add a proper card entry for this device, rather than abusing entries that are
not-quite-right.
Regards,
	Hans

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-05-21 08:06:11 -03:00
Linus Torvalds
99bece775f Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c changes from Wolfram Sang:

 - an arbitration driver.  While the driver is quite simple, it caused
   discussion if we need additional arbitration on top of the one
   specified in the I2C standard.  Conclusion is that I accept a few
   generic mechanisms, but not very specific ones.

 - the core lost the detach_adapter() call.  It has no users anymore and
   was in the way for other cleanups.  attach_adapter() is sadly still
   there since there are users waiting to be converted.

 - the core gained a bus recovery infrastructure.  I2C defines a way to
   recover if the data line is stalled.  This mechanism is now in the
   core and drivers can now pass some data to make use of it.

 - bigger driver cleanups for designware, s3c2410

 - removing superfluous refcounting from drivers

 - removing Ben Dooks as second maintainer due to inactivity.  Thanks
   for all your work so far, Ben!

 - bugfixes, feature additions, devicetree fixups, simplifications...

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
  i2c: xiic: must always write 16-bit words to TX_FIFO
  i2c: octeon: use HZ in timeout value
  i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
  i2c: designware-pci: drop superfluous {get|put}_device
  i2c: designware-plat: drop superfluous {get|put}_device
  i2c: davinci: drop superfluous {get|put}_device
  MAINTAINERS: Ben Dooks is inactive regarding I2C
  i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
  i2c: at91: convert to dma_request_slave_channel_compat()
  i2c: mxs: do error checking and handling in PIO mode
  i2c: mxs: remove races in PIO code
  i2c-designware: switch to use runtime PM autosuspend
  i2c-designware: use usleep_range() in the busy-loop
  i2c-designware: enable/disable the controller properly
  i2c-designware: use dynamic adapter numbering on Lynxpoint
  i2c-designware-pci: use managed functions pcim_* and devm_*
  i2c-designware-pci: use dev_err() instead of printk()
  i2c-designware: move to managed functions (devm_*)
  i2c: remove CONFIG_HOTPLUG ifdefs
  i2c: s3c2410: Add SMBus emulation for block read
  ...
2013-05-02 14:38:53 -07:00
Lars-Peter Clausen
bf51a8c5e0 i2c: Ignore return value of i2c_del_adapter()
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2013-04-02 07:06:03 +02:00
Mauro Carvalho Chehab
f9f11dfe48 Linux 3.9-rc5
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
 xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
 BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
 Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
 4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
 k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
 =q15K
 -----END PGP SIGNATURE-----

Merge tag 'v3.9-rc5' into patchwork

Linux 3.9-rc5

* tag 'v3.9-rc5': (1080 commits)
  Linux 3.9-rc5
  Revert "lockdep: check that no locks held at freeze time"
  dw_dmac: adjust slave_id accordingly to request line base
  dmaengine: dw_dma: fix endianess for DT xlate function
  PNP: List Rafael Wysocki as a maintainer
  rbd: don't zero-fill non-image object requests
  ia64 idle: delete stale (*idle)() function pointer
  Btrfs: don't drop path when printing out tree errors in scrub
  target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
  tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
  Revert "mm: introduce VM_POPULATE flag to better deal with racy userspace programs"
  usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
  mg_disk: fix error return code in mg_probe()
  Btrfs: fix wrong return value of btrfs_lookup_csum()
  Btrfs: fix wrong reservation of csums
  Btrfs: fix double free in the btrfs_qgroup_account_ref()
  Btrfs: limit the global reserve to 512mb
  Btrfs: hold the ordered operations mutex when waiting on ordered extents
  Btrfs: fix space accounting for unlink and rename
  Btrfs: fix space leak when we fail to reserve metadata space
  ...
2013-04-01 09:54:14 -03:00
Hans de Goede
35ccecef6e [media] [REGRESSION] bt8xx: Fix too large height in cropcap
Since commit a1fd287780:
"[media] bttv-driver: fix two warnings"
cropcap.defrect.height and cropcap.bounds.height for the PAL entry are 32
resp 30 pixels too large, if a userspace app (ie xawtv) actually tries to use
the full advertised height, the resulting image is broken in ways only a
screenshot can describe.
The cause of this is the fix for this warning:
drivers/media/pci/bt8xx/bttv-driver.c:308:3: warning: initialized field overwritten [-Woverride-init]
In this chunk of the commit:
@@ -301,11 +301,10 @@ const struct bttv_tvnorm bttv_tvnorms[] = {
                        /* totalwidth */ 1135,
                        /* sqwidth */ 944,
                        /* vdelay */ 0x20,
-                       /* sheight */ 576,
-                       /* videostart0 */ 23)
                /* bt878 (and bt848?) can capture another
                   line below active video. */
-               .cropcap.bounds.height = (576 + 2) + 0x20 - 2,
+                       /* sheight */ (576 + 2) + 0x20 - 2,
+                       /* videostart0 */ 23)
        },{
                .v4l2_id        = V4L2_STD_NTSC_M | V4L2_STD_NTSC_M_KR,
                .name           = "NTSC",
Which replaces the overriding of cropcap.bounds.height initialization outside
of the CROPCAP macro (which also initializes it), with passing a
different sheight value to the CROPCAP macro.
There are 2 problems with this warning fix:
1) The sheight value is used twice in the CROPCAP macro, and the old code
   only changed one resulting value.
2) The old code increased the .cropcap.bounds.height value (and did not
   touch the .cropcap.defrect.height value at all) by 2, where as the fixed
   code increases it by 32, as the fixed code passes (576 + 2) + 0x20 - 2
   to the CROPCAP macro, but the + 0x20 - 2 is already done by the macro so
   now is done twice for .cropcap.bounds.height, and also is applied to
   .cropcap.defrect.height where it should not be applied at all.
This patch fixes this by adding an extraheight parameter to the CROPCAP entry
and using it for the PAL entry.

Cc: stable@kernel.org	# For Kernel 3.8
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-26 08:37:00 -03:00
Hans Verkuil
977ba3b1b7 [media] v4l2: add const to argument of write-only s_register ioctl
This ioctl is defined as IOW, so pass the argument as const.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-24 08:47:01 -03:00
Hans Verkuil
314527acbb [media] v4l2: pass std by value to the write-only s_std ioctl
This ioctl is defined as IOW, so pass the argument by value instead of by
reference. I could have chosen to add const instead, but this is 1) easier
to handle in drivers and 2) consistent with the s_std subdev operation.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-24 06:47:00 -03:00
Hans Verkuil
2f73c7c582 [media] v4l2: add const to argument of write-only s_tuner ioctl
This ioctl is defined as IOW, so pass the argument as const.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-24 06:31:23 -03:00
Hans Verkuil
b530a447bb [media] v4l2: add const to argument of write-only s_frequency ioctl
This ioctl is defined as IOW, so pass the argument as const.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-24 06:25:34 -03:00
Frank Schaefer
0757f5c503 [media] bttv: apply mute settings on open
Previously, this has been done implicitly for video device nodes by calling
set_input() (which calls audio_input() and also modified the mute
setting).
Since input and mute setting are now untangled (as much as possible), we need to
apply the mute setting with an explicit call to audio_mute().
Also apply the mute setting when the radio device node gets opened.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-23 11:33:01 -03:00
Frank Schaefer
da9f07f2d4 [media] bttv: do not unmute the device before the first open
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-23 11:32:48 -03:00
Frank Schaefer
b1a301572a [media] bttv: untangle audio input and mute setting
Split function audio_mux():
move the mute setting part to function audio_mute() and the input setting part
to function audio_input().

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-23 11:32:26 -03:00
Frank Schaefer
5f45678173 [media] bttv: separate GPIO part from function audio_mux()
Move the GPIO part of function audio_mux() to a separate function
audio_mux_gpio().
This prepares the code for the next patch which will separate mute and input
setting.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-23 11:31:49 -03:00
Frank Schaefer
2166f0a971 [media] bttv: rename field 'audio' in struct 'bttv' to 'audio_input'
'audio_input' better describes the meaning of this field.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-23 11:31:13 -03:00
Frank Schaefer
20167f17f1 [media] bttv: do not save the audio input in audio_mux()
We can't and do not save the mute setting in function audio_mux(), so we
should also not save the input in this function for consistency.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-23 11:30:55 -03:00
Frank Schaefer
598728e920 [media] bttv: audio_mux(): do not change the value of the v4l2 mute control
There are cases where we want to call audio_mux() without changing the value of
the v4l2 mute control, for example
- mute mute on last close
- mute on device probing

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-23 11:30:21 -03:00
Frank Schaefer
28cafc38ec [media] bttv: audio_mux(): use a local variable "gpio_mute" instead of modifying the function parameter "mute"
Function audio_mux() actually deals with two types of mute: gpio mute and
subdevice muting.
This patch claryfies the meaning of these values, but mainly prepares the code for
the next patch.

Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-03-23 11:29:10 -03:00