During cpufreq driver's registration, if the ->init() callback for all
the CPUs fail then there is not much point in keeping the driver around
as it will only account for more of unnecessary noise, for example
cpufreq core will try to suspend/resume the driver which never got
registered properly.
The removal of such a driver is avoided if the driver carries the
CPUFREQ_STICKY flag. This was added way back [1] in 2004 and perhaps no
one should ever need it now. A lot of drivers do set this flag, probably
because they just copied it from other drivers.
This was added earlier for some platforms [2] because their cpufreq
drivers were getting registered before the CPUs were registered with
subsys framework. And hence they used to fail.
The same isn't true anymore though. The current code flow in the kernel
is:
start_kernel()
-> kernel_init()
-> kernel_init_freeable()
-> do_basic_setup()
-> driver_init()
-> cpu_dev_init()
-> subsys_system_register() //For CPUs
-> do_initcalls()
-> cpufreq_register_driver()
Clearly, the CPUs will always get registered with subsys framework
before any cpufreq driver can get probed. Remove the flag and update the
relevant drivers.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/include/linux/cpufreq.h?id=7cc9f0d9a1ab04cedc60d64fd8dcf7df224a3b4d # [1]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/arch/arm/mach-sa1100/cpu-sa1100.c?id=f59d3bbe35f6268d729f51be82af8325d62f20f5 # [2]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq:
cpufreq: Make cpufreq_generic_init() return void
cpufreq: imx-cpufreq-dt: Add i.MX8MN support
cpufreq: Add QoS requests for userspace constraints
cpufreq: intel_pstate: Reuse refresh_frequency_limits()
cpufreq: Register notifiers with the PM QoS framework
PM / QoS: Add support for MIN/MAX frequency constraints
PM / QOS: Pass request type to dev_pm_qos_read_value()
PM / QOS: Rename __dev_pm_qos_read_value() and dev_pm_qos_raw_read_value()
PM / QOS: Pass request type to dev_pm_qos_{add|remove}_notifier()
It always returns 0 (success) and its return type should really be void.
Over that, many drivers have added error handling code based on its
return value, which is not required at all.
Change its return type to void and update all the callers.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header containing the configuration structure for davinci cpufreq
driver lives in mach-davinci/include/mach/. This is fine for now but
if we want to make davinci part of the multi_v5 build, no code external
to mach-davinci should include machine-specific headers.
Move the configuration structure to include/linux/platform_data.
While we're at it: convert the GPL-2.0 boilerplate to a proper SPDX
license identifier.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This function is confusing - its second argument is an index to the
freq table, not the requested clock rate in Hz, but it's used as the
set_rate callback for the pll0 clock. It leads to an oops when the
caller doesn't know the internals and passes the rate in Hz as
argument instead of the cpufreq index since this argument isn't bounds
checked either.
Fix it by iterating over the array of supported frequencies and
selecting a one that matches or returning -EINVAL for unsupported
rates.
Also: update the davinci cpufreq driver. It's the only user of this
clock and currently it passes the cpufreq table index to
clk_set_rate(), which is confusing. Make it pass the requested clock
rate in Hz.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[nsekhar@ti.com: commit headline update]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
policy->freq_table will always be valid for this platform, otherwise
driver's probe() would fail. And so this routine will *always* return
after calling cpufreq_frequency_table_verify().
This can be done using the generic callback provided by core, lets use
it instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_generic_exit() is empty now and can be deleted.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFreq drivers that use clock frameworks interface,i.e. clk_get_rate(),
to get CPUs clk rate, have similar sort of code used in most of them.
This patch adds a generic ->get() which will do the same thing for them.
All those drivers are required to now is to set .get to cpufreq_generic_get()
and set their clk pointer in policy->clk during ->init().
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in frequency table.
On some systems we can't really say what frequency we're running at the moment
and so for these we shouldn't check if we are running at a frequency present in
frequency table. And so we really can't force this for all the cpufreq drivers.
Hence we are created another flag here: CPUFREQ_NEED_INITIAL_FREQ_CHECK that
will be marked by platforms which want to go for this check at boot time.
Initially this is done for all ARM platforms but others may follow if required.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the drivers do following in their ->target_index() routines:
struct cpufreq_freqs freqs;
freqs.old = old freq...
freqs.new = new freq...
cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
/* Change rate here */
cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
This is replicated over all cpufreq drivers today and there doesn't exists a
good enough reason why this shouldn't be moved to cpufreq core instead.
There are few special cases though, like exynos5440, which doesn't do everything
on the call to ->target_index() routine and call some kind of bottom halves for
doing this work, work/tasklet/etc..
They may continue doing notification from their own code as flag:
CPUFREQ_ASYNC_NOTIFICATION is already set for them.
All drivers are also modified in this patch to avoid breaking 'git bisect', as
double notification would happen otherwise.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, the prototype of cpufreq_drivers target routines is:
int target(struct cpufreq_policy *policy, unsigned int target_freq,
unsigned int relation);
And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.
So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.
This patch implements the new light weight prototype for target_index() routine.
It looks like this:
int target_index(struct cpufreq_policy *policy, unsigned int index);
CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.
This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.
It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the davinci driver.
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the users of cpufreq_verify_within_limits() calls it for
limiting with min/max from policy->cpuinfo. We can make that code
simple by introducing another routine which will do this for them
automatically.
This patch adds another routine cpufreq_verify_within_cpu_limits()
and updates others to use it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PRECHANGE and POSTCHANGE notifiers must be called in groups, i.e either both
should be called or both shouldn't be.
In case we have started PRECHANGE notifier and found an error, we must call
POSTCHANGE notifier with freqs.new = freqs.old to guarantee that sequence of
calling notifiers is complete.
Davinci driver was taking care of it but frequency isn't restored to freqs.old.
This patch fixes it.
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch moves cpufreq driver of ARM based davinci platform to
drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
