Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the sdhci
esdhc-imx driver to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here we use '|=' to set the tuning-step, but before that, we should
clear the tuning-step, otherwise we could got the wrong setting.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By default, for all imx SoC types, the watermark level is 16, and the
burst length is 8. But if the SDIO/SD/MMC I/O speed is fast enough,
this default watermark level and burst length will be the performance
bottleneck.
For example, i.MX7D support eMMC HS400 mode, this mode can run in 8 bit,
200MHZ DDR mode. So the I/O speed improve a lot compare to SD3.0.
The default burst length is 8, if we don't change this value, in
HS400 mode, when we do eMMC read operation, we can find that the
clock signal will stop for a period of time. This means the speed
of data moving on AHB bus is slower than I/O speed. So we should
improve the speed of data moving on AHB bus.
This patch set the default burst length as 16, and set the default
watermark level as 64. The test result is the clock signal has
no stop during the eMMC HS400 operation.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we find that if a usdhc is choosed to boot system, then ROM
code will set the burst length enable bit of this usdhc as 0.
This will make performance drop a lot if this usdhc's burst length is
configed. So this patch set back the burst_length_enable bit as 1,
which is the default value, and means burst length is enabled for INCR.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tuning-step is the delay cell steps in tuning procedure. The default value
of tuning-step is 1. Some boards or cards need another value to pass the
tuning procedure. For example, imx7d-sdb board need the tuning-step value
as 2, otherwise it can't pass the tuning procedure.
So this patch add the tuning-step setting in driver, so that user can set
the tuning-step value in dts.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.
So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need those duplicated parsing anymore.
Note: fsl,cd-controller is also deleted due to the driver does
not support controller card detection anymore after switch to runtime pm.
And there's no user of it right now in device tree.
wp-gpios is kept because we're still support fsl,wp-controller,
so we need a way to check if it's gpio wp or controller wp.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is an incremental fix of commit
e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").
After commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().
Current code only exclude the checking of wp_type for dt platform which
does not make sense.
This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.
Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.
Commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.
This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.
Fixes: 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Reviewed-by: Johan Derycke <johan.derycke@barco.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The iMX6Q/DL can not support HS200 mode while iMX6SL and iMX6SX can,
so introduce a new flag to distinguish them.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The imx6sx usdhc is derived from imx6sl, the difference is minor.
imx6sx have the errata ESDHC_FLAG_ERR004536 fixed.
So introduce a new compatible string for imx6sx to distinguish them.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The uSDHC has an ADMA Length Mismatch errata ERR004536 which may
cause ADMA work abnormally. The errata has already been fixed for
i.MX6Q TO1.2 and i.MX6DL TO1.1 by enable the bit 7 in 0x6c register.
Unfortunately this fix is not included in i.MX6SL.
So we disable ADMA for i.MX6SL and use SDMA instead.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The usdhc does not have missing card interrupt issue, so don't execute
workaround for usdhc.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In esdhc_writel_le() function, there's duplicated checking of the same
register as follows:
"if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE))".
Merge them into one and remove the duplicated one.
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only user of this driver that has not been converted to fully
device tree is the i.MX35 SoC.
There is a i.MX35-based board (mach-pcm043.c) that uses platform data
to pass wp_gpio and cd_gpio information.
Commit 8d86e4fccc ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
broke the platform data case by removing mmc_gpio_request_ro() and
mmc_gpio_request_cd(), so restore the functionality for the non-dt
case.
Also, restore the check for ESDHC_CD_CONTROLLER so that we can still
support the "fsl,cd-controller" property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_of_parse() should be placed inside sdhci_esdhc_imx_probe_dt() as it
suits only for the dt case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
My Pengutronix address is not valid anymore, redirect people to the Pengutronix
kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently it is not possible to use 'mmc-pwrseq-simple' property with this
driver because mmc_of_parse() is never called.
mmc_of_parse() calls mmc_pwrseq_alloc() that manages MMC power sequence and
allows passing GPIOs in the devicetree to properly power/reset the Wifi
chipset.
When using mmc_of_parse() we no longer need to have custom code to request
card-detect and write-protect pins, as this can now be handled by the mmc
core.
Tested on a imx6sl-warp board where BT/Wifi is functional and also on a
imx6q-sabresd.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Static checkers suggest that probably we intended to put curly braces
around the writel() to make it part of the else path. But, I think
actually the indenting is off and the code works fine as is.
The stray tab was introduced in 0322191e62 ('mmc: sdhci-esdhc-imx: add
sd3.0 SDR clock tuning support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By configure runtime PM prior we enable the use of it, we close the gap
for strange and unhandled conditions. Moreover it makes us rely on the
driver core, after finalized ->probe(), to request an inactive device
to become runtime PM idle/suspended, which earlier potentially could
happen already at pm_runtime_set_autosuspend_delay().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since sdhci_remove_host() access the device, we need to make sure it's
runtime PM resumed.
To handle clock gating properly in remove, we first have to make sure
the clocks are ungated.
To fix both these issues, by invoking pm_runtime_get_sync() early in
->remove() callback. Later once we disabled runtime PM, we can restore
the usage count.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Instead of having a local function taking care of sending the tuning
command, let's use the common mmc_send_tuning() API provided by the mmc
core. In this way the request will be handled as any other request by
sdhci core.
As an effect of this change, the pm_runtime_get_sync() call at
esdhc_prepare_tuning() isn't needed any more.
This patch will also introduce another change in behavior, since before
the response pattern to the tuning command wasn't verified by
sdhci-esdhc-imx. The mmc_send_tuning() does that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mmc/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit ad93220de7 ("mmc: sdhci-esdhc-imx: change pinctrl state
according to uhs mode") exits the probe in case there are no valid
pinctrl states found.
As there are configurations doing the pin mux properly in the boot
loader, don't exit. Just warn, but go on in case if there are no
pinctrl states in the device tree.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default sdhci driver write 0xE into timeout counter register to
set the maximum timeout. The value is not correct for uSDHC since the
max counter value for uSDHC is 0xF.
Instead of using common timeout code in sdhci, we implement esdhc_set_timeout
to handle the difference between eSDHC and uSDHC.
Currently we simply set the max timeout value as before.
But in the future, we probably may implement IMX specific timeout
setting algorithm and use suitable timeout for different CMDs.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default sdhci code use the 1 << 27 as the max timeout counter to
to calculate the max_busy_timeout, however it's not correct for uSDHC
since its the max counter is 1 << 28.
Implement esdhc_get_max_timeout_cout to handle it correctly.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We no longer need to emulate the uhs_mode field of the host control2
register - the main sdhci driver never reads this back to evaluate
the current mode as it caches the current mode instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The set_uhs_signaling() method gives the impression that it can fail,
but anything returned from the method is entirely ignored by the sdhci
driver. So returning failure has no effect.
So, kill the idea that it's possible for this to return an error by
removing the returned value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
It is far from obvious what this is doing, and it looks like it's an
unbalanced runtime_pm_get() call. However, the put is inside
sdhci_tasklet_finish(), so it's not unbalanced at all. This should
be documented so people know what's going on here. Do so.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
sdhci-esdhc-imx tries to DMA to the kernel stack when tuning the
interface, which causes dma-debug to complain. Fix this by kmallocing
a buffer to hold the received tuning pattern.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the setting of mmc->actual_clock to zero into the set_clock
handlers themselves. This will allow us to clean up the calling
logic for the set_clock() method, and turn sdhci_set_clock() into
a library function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We don't need implementations to do this, since the only time it's
necessary is when we change the clock, and the only place that happens
is in sdhci_do_set_ios(). So, move it there, and remove it from the
iMX platform backend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Freescale esdhc driver is the only driver which needs the interrupt
registers restored after a reset. Move this quirk to be part of the
ESDHC driver implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than having platform_reset_enter/platform_reset_exit methods,
turn the core of the reset handling into a library function which
platforms can call at the appropriate moment in their (new) reset
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Allow SDIO interrupts to be received while the SDHCI host is runtime
suspended. We do this by leaving the AHB clock enabled while the
host is runtime suspended so we can access the SDHCI registers, and
so read and raise the SDIO card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Since the clock is managed by runtime pm currently, we do not need
disable it again during driver remove function, or it will cause
clock disable count mismatch issue since the clocks have already been disabled.
The issue can be simply reproduced by unbind the devices via sysfs.
mx6slevk:/sys/bus/platform/drivers/sdhci-esdhc-imx# echo 2194000.usdhc > unbind
mmc1: card aaaa removed
------------[ cut here ]------------
WARNING: CPU: 0 PID: 657 at drivers/clk/clk.c:842 __clk_disable+0x68/0x88()
Modules linked in:
CPU: 0 PID: 657 Comm: sh Not tainted 3.13.0-rc1+ #285
Backtrace:
[<80012160>] (dump_backtrace+0x0/0x10c) from [<80012438>] (show_stack+0x18/0x1c)
r6:80481370 r5:00000000 r4:8088ecc8 r3:00000000
[<80012420>] (show_stack+0x0/0x1c) from [<80616b14>] (dump_stack+0x84/0x9c)
[<80616a90>] (dump_stack+0x0/0x9c) from [<80027158>] (warn_slowpath_common+0x70/0x94)
r5:00000009 r4:00000000
[<800270e8>] (warn_slowpath_common+0x0/0x94) from [<80027220>] (warn_slowpath_null+0x24/0x2c)
r8:bec4ff78 r7:0000000e r6:bf91d800 r5:bf81d080 r4:bf81d080
[<800271fc>] (warn_slowpath_null+0x0/0x2c) from [<80481370>] (__clk_disable+0x68/0x88)
[<80481308>] (__clk_disable+0x0/0x88) from [<8048148c>] (clk_disable+0x20/0x2c)
r4:200f0113 r3:bf95ec00
[<8048146c>] (clk_disable+0x0/0x2c) from [<80463bd8>] (sdhci_esdhc_imx_remove+0x64/0xa4)
r5:bf81d080 r4:bfabb010
[<80463b74>] (sdhci_esdhc_imx_remove+0x0/0xa4) from [<8032e82c>] (platform_drv_remove+0x20/0x24)
r6:808ae0e0 r5:808ae0e0 r4:bf91d810 r3:80463b74
[<8032e80c>] (platform_drv_remove+0x0/0x24) from [<8032d010>] (__device_release_driver+0x78/0xd0)
[<8032cf98>] (__device_release_driver+0x0/0xd0) from [<8032d090>] (device_release_driver+0x28/0x34)
r5:bf91d810 r4:bf91d844
[<8032d068>] (device_release_driver+0x0/0x34) from [<8032c0c8>] (unbind_store+0x80/0xc4)
r5:bf91d810 r4:80899ba0
[<8032c048>] (unbind_store+0x0/0xc4) from [<8032b648>] (drv_attr_store+0x28/0x34)
r7:bed73100 r6:0000000e r5:00000000 r4:8032b620
[<8032b620>] (drv_attr_store+0x0/0x34) from [<80140580>] (sysfs_write_file+0x1b0/0x1e4)
[<801403d0>] (sysfs_write_file+0x0/0x1e4) from [<800dcda0>] (vfs_write+0xb4/0x190)
[<800dccec>] (vfs_write+0x0/0x190) from [<800dd3e4>] (SyS_write+0x44/0x80)
r9:0000000e r8:00000000 r7:01a00408 r6:bf3b1c00 r5:00000000
r4:00000000
[<800dd3a0>] (SyS_write+0x0/0x80) from [<8000e900>] (ret_fast_syscall+0x0/0x48)
r9:bec4e000 r8:8000eac4 r7:00000004 r6:76f5fb40 r5:01a00408
r4:0000000e
---[ end trace a0897d268e6233b2 ]---
If without runtime pm, we just run as before to match the clock enable
in probe function.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Fix the following sparse warning:
drivers/mmc/host/sdhci-esdhc-imx.c:617:35: warning: Using plain integer as NULL pointer
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The root clock will be disabled in runtime pm to save power.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since we're using common esdhc_send_command for tuning commands and
the core code will call pm_runtime_put after command is finished.
So we add a pm_runtime_get_sync here to get the balance.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current code will clear all turning related bits like ESDHC_STD_TUNING_EN
and ESDHC_MIX_CTRL_FBCLK_SEL when clear SDHCI_CTRL_EXEC_TUNING.
This may cause the card which has already passed the turning to become
unwork since the turning status lost.
We observed this failure when enable runtime pm.
BTW, imx needs to enable ESDHC_MIX_CTRL_FBCLK_SEL bit for turned clock.
The FBCLK_SEL will be cleared when SDHCI_CTRL_TUNED_CLK is cleared
and SDHCI_CTRL_EXEC_TUNING is not set.
This is used in case we change to another normal card from a UHS card
in the same slot. FBCLK_SEL is not needed for normal card.
After that, SDHCI_CTRL_EXEC_TUNING will only affect ESDHC_MIX_CTRL_EXE_TUNE.
Clearing it does not affect the turned card to remain working on UHS mode.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
