Add macro for defining static pins in the board file.
We can now start implementing pin multiplexing in the platform init
code for devices that call omap_hwmod_mux_init. Currently that is
only implemented for serial.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently OMAP_DEVICE_PAD_IDLE flag is used to mux pins
dynamically. This can be simplified by using the enabled
state variable of each pad. This also fixes the issue of
the static pads not getting muxed after idling and
disable/enable state transitions.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This avoids going through the list unnecessarily when
idling devices for runtime PM.
Based on an earlier patch by sricharan <r.sricharan@ti.com>.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow hwmod state changes to mux pads based on the state changes.
By default, only enable and disable the pads. In some rare cases
dynamic remuxing for the idles states is needed, this can be done
by passing the enable, idle, and off pads from board-*.c file along
with OMAP_DEVICE_PAD_REMUX flag.
Thanks to Paul Walmsley <paul@booyaka.com> for the comments on the
hwmod related changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows adding hwmod specific pads dynamically during the
platform device init.
Note that we don't currently have the hwmod specific signals
listed in the hwmod data, but struct omap_hwmod_mux_info will
make that possible if necessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_OMAP_MUX is not enabled, we can define board_mux in the header
file instead of forcing every single board to define it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated for combined board-zoom files]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Please note that the full muxmodes are re-defined for ES2 instead
of using the subset. There are 81 differences among 204 pins.
The subset fixup will have to iterate over the whole list for each
subset entry, which can lead to an important number of iteration.
On the other hand, it will take much more memory at boot time.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Add data for OMAP4430 generated from HW pinout & register database.
The data set is split in two partitions for both core and wkup.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Starting on OMAP4, the pin mux configuration is located in two
different partitions of the control module (CODE_PAD and WKUP_PAD).
The first one is inside the core power domain whereas the second
one is inside the wakeup.
- Add the capability to add any number of partition during board init
time depending of Soc partitioning.
- Add some init flags as well in order to avoid explicit Soc version
check inside the mux core code.
- Add a comment with mux0 mode on top of omap_mux/board/<partition>
if the current mux mode is not the default one.
Thanks to Tony Lindgren <tony@atomide.com> for the following improvements:
- Add omap_mux_get for getting the partition data so platform level
device code can use it.
- Fix the rx51 board code to use the new API.
- Do not store the partition for each mux entry. Look up the partition
for debugfs instead.
Thanks to Dan Murphy <dmurphy@ti.com> for testing on OMAP4 and reporting
a couple of bugs.
Thanks to Anand Gadiyar <gadiyar@ti.com> for testing on OMAP3 zoom and
bug report.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Murphy Dan <dmurphy@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Add data for 2430. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add data for 2420. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make the omap_mux_read and write available for board code,
and rename omap_mux_set_board_signals into omap_mux_write_array.
Also add the related prototypes and comments into mux.h.
In some cases we want to change the signals dynamically,
mostly for power management.
Note that we cannot use the signal names as they are set
__init to save memory.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add new style mux data for 34xx. This should also
work with 3630 easily by adding the processor subset
and ball data.
Note that this data is __initdata, and gets optimized
out except for the GPIO pins if CONFIG_OMAP_MUX
is not set.
Also note that this data uses omap3630 naming for
the SDMMC registers instead of 34xx naming with just
MMC.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initially only for 34xx. This code allows us to:
- Make the code more generic as the omap internal signal
names can stay the same across omap generations for some
devices
- Map mux registers to GPIO registers that is needed for
dynamic muxing of pins during off-idle
- Override bootloader mux values via kernel cmdline using
omap_mux=some.signa1=0x1234,some.signal2=0x1234
- View and set the mux registers via debugfs if
CONFIG_DEBUG_FS is enabled
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>