Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For some silicons, the pin configuration register can control
the output of the pin when the pad including the pin enter
low power mode.
For example, the pin can be "Drive 1", "Drive 0", "Float" when
the pad including the pin enter low power mode.
It is very useful when you want to control the power leakeage
when the SOC enter low power mode, and can save more power for
the low power mode.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove extra comma in pinctrl-single documentation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin control registers can have interrupts for example
for device wake-up. These interrupts can be treated as a
chained interrupt controller as suggested earlier by
Linus Walleij <linus.walleij@linaro.org>.
This patch adds support for interrupts in a way that
should be pretty generic, and works for the omaps that
support wake-up interrupts. On omaps, there's an
interrupt enable and interrupt status bit for each pin.
The two pinctrl domains on omaps share a single interrupt
from the PRM chained interrupt handler. Support for
other similar hardware should be easy to add.
Note that this patch does not attempt to handle the
wake-up interrupts automatically unlike the earlier
patches. This patch allows the device drivers to do
a request_irq() on the wake-up pins as needed. I'll
try to do also a separate generic patch for handling
the wake-up events automatically.
Also note that as this patch makes the pinctrl-single
an irq controller, the current bindings need some
extra trickery to use interrupts from two different
interrupt controllers for the same driver. So it
might be worth waiting a little on the patches
enabling the wake-up interrupts from drivers as there
should be a generic way to handle it coming. And also
there's been discussion of interrupts-extended binding
for using interrupts from multiple interrupt controllers.
In any case, this patch should be ready to go allowing
handling the wake-up interrupts in a generic way, or
separately from the device drivers.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: linux-kernel@vger.kernel.org
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support to configure multiple pins in each register, existing
implementation added by [1] does not support full fledge multiple pin
configuration in single register, reports a pin clash when different
modules configure different bits of same register. The issue reported
and discussed here
http://www.spinics.net/lists/arm-kernel/msg235213.html
With pinctrl-single,bits-per-mux property specified, use function-mask
property to find out number pins to configure. Allocate and register
pin control functions based sub mask.
Tested on da850/omap-l138 EVM.
does not support variable submask for pins.
does not support pinconf.
[1] "pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux"
(9e605cb68a),
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Reported-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add comments with pinconf & gpio range in the document of
pinctrl-single.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.
pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add one-register-per-pin type device tree based pinctrl driver.
This driver has been tested on omap2+ series of processors,
where there is either an 8 or 16-bit padconf register for each pin.
Support for other similar pinmux controllers can be added.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
