As patch 'ip_gre: add the support for i/o_flags update via netlink'
did for netlink, we also need to do the same job for these update
via ioctl.
This patch is to update i/o_flags and call ipgre_link_update to
recalculate these gre properties after ip_tunnel_ioctl does the
common update.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ip_gre is using ip_tunnel_changelink to update it's properties, but
ip_tunnel_changelink in ip_tunnel doesn't update i/o_flags as a common
function.
o_flags updates would cause that tunnel->tun_hlen / hlen and dev->mtu /
needed_headroom need to be recalculated, and dev->(hw_)features need to
be updated as well.
Therefore, we can't just add the update into ip_tunnel_update called
in ip_tunnel_changelink, and it's also better not to touch ip_tunnel
codes.
This patch updates i/o_flags and calls ipgre_link_update to recalculate
these gre properties after ip_tunnel_changelink does the common update.
Note that since ipgre_link_update doesn't know the lower dev, it will
update gre->hlen, dev->mtu and dev->needed_headroom with the value of
'new tun_hlen - old tun_hlen'. In this way, we can avoid many redundant
codes, unlike ip6_gre.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to early patch for erspan_xmit(), the ARPHDR_ETHER device
is the length of the whole ether packet. So skb->len should subtract
the dev->hard_header_len.
Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel")
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: David Laight <David.Laight@aculab.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch 'ip_gre: ipgre_tap device should keep dst' fixed
the issue ipgre_tap dev mtu couldn't be updated in tx path.
The same fix is needed for erspan as well.
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to __gre_tunnel_init, tunnel->hlen should be set as the
headers' length between inner packet and outer iphdr.
It would be used especially to calculate a proper mtu when updating
mtu in tnl_update_pmtu. Now without setting it, a bigger mtu value
than expected would be updated, which hurts performance a lot.
This patch is to fix it by setting tunnel->hlen with:
tunnel->tun_hlen + tunnel->encap_hlen + sizeof(struct erspanhdr)
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a ARPHRD_ETHER device, skb->len in erspan_xmit is the length
of the whole ether packet. So before checking if a packet size
exceeds the mtu, skb->len should subtract dev->hard_header_len.
Otherwise, all packets with max size according to mtu would be
trimmed to be truncated packet.
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
erspan only uses the first 10 bits of session_id as the key to look
up the tunnel. But in erspan_rcv, it missed 'session_id & ID_MASK'
when getting the key from session_id.
If any other flag is also set in session_id in a packet, it would
fail to find the tunnel due to incorrect key in erspan_rcv.
This patch is to add 'session_id & ID_MASK' there and also remove
the unnecessary variable session_id.
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without keeping dst, the tunnel will not update any mtu/pmtu info,
since it does not have a dst on the skb.
Reproducer:
client(ipgre_tap1 - eth1) <-----> (eth1 - ipgre_tap1)server
After reducing eth1's mtu on client, then perforamnce became 0.
This patch is to netif_keep_dst in gre_tap_init, as ipgre does.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to gre, vxlan, geneve, ipip tunnels, allow ERSPAN tunnels to
operate in 'collect metadata' mode. bpf_skb_[gs]et_tunnel_key() helpers
can make use of it right away. OVS can use it as well in the future.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch refactors the gre_fb_xmit function, by creating
prepare_fb_xmit function for later ERSPAN collect_md mode patch.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iph is being assigned the same value twice; remove the redundant
first assignment. (Thanks to Nikolay Aleksandrov for pointing out
that the first asssignment should be removed and not the second)
Fixes warning:
net/ipv4/ip_gre.c:265:2: warning: Value stored to 'iph' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds ERSPAN type II tunnel support. The implementation
is based on the draft at [1]. One of the purposes is for Linux
box to be able to receive ERSPAN monitoring traffic sent from
the Cisco switch, by creating a ERSPAN tunnel device.
In addition, the patch also adds ERSPAN TX, so Linux virtual
switch can redirect monitored traffic to the ERSPAN tunnel device.
The traffic will be encapsulated into ERSPAN and sent out.
The implementation reuses tunnel key as ERSPAN session ID, and
field 'erspan' as ERSPAN Index fields:
./ip link add dev ers11 type erspan seq key 100 erspan 123 \
local 172.16.1.200 remote 172.16.1.100
To use the above device as ERSPAN receiver, configure
Nexus 5000 switch as below:
monitor session 100 type erspan-source
erspan-id 123
vrf default
destination ip 172.16.1.200
source interface Ethernet1/11 both
source interface Ethernet1/12 both
no shut
monitor erspan origin ip-address 172.16.1.100 global
[1] https://tools.ietf.org/html/draft-foschiano-erspan-01
[2] iproute2 patch: http://marc.info/?l=linux-netdev&m=150306086924951&w=2
[3] test script: http://marc.info/?l=linux-netdev&m=150231021807304&w=2
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Meenakshi Vohra <mvohra@vmware.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature allows the administrator to set an fwmark for
packets traversing a tunnel. This allows the use of independent
routing tables for tunneled packets without the use of iptables.
There is no concept of per-packet routing decisions through IPv4
tunnels, so this implementation does not need to work with
per-packet route lookups as the v6 implementation may
(with IP6_TNL_F_USE_ORIG_FWMARK).
Further, since the v4 tunnel ioctls share datastructures
(which can not be trivially modified) with the kernel's internal
tunnel configuration structures, the mark attribute must be stored
in the tunnel structure itself and passed as a parameter when
creating or changing tunnel attributes.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make struct pernet_operations::id unsigned.
There are 2 reasons to do so:
1)
This field is really an index into an zero based array and
thus is unsigned entity. Using negative value is out-of-bound
access by definition.
2)
On x86_64 unsigned 32-bit data which are mixed with pointers
via array indexing or offsets added or subtracted to pointers
are preffered to signed 32-bit data.
"int" being used as an array index needs to be sign-extended
to 64-bit before being used.
void f(long *p, int i)
{
g(p[i]);
}
roughly translates to
movsx rsi, esi
mov rdi, [rsi+...]
call g
MOVSX is 3 byte instruction which isn't necessary if the variable is
unsigned because x86_64 is zero extending by default.
Now, there is net_generic() function which, you guessed it right, uses
"int" as an array index:
static inline void *net_generic(const struct net *net, int id)
{
...
ptr = ng->ptr[id - 1];
...
}
And this function is used a lot, so those sign extensions add up.
Patch snipes ~1730 bytes on allyesconfig kernel (without all junk
messing with code generation):
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
Unfortunately some functions actually grow bigger.
This is a semmingly random artefact of code generation with register
allocator being used differently. gcc decides that some variable
needs to live in new r8+ registers and every access now requires REX
prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be
used which is longer than [r8]
However, overall balance is in negative direction:
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
function old new delta
nfsd4_lock 3886 3959 +73
tipc_link_build_proto_msg 1096 1140 +44
mac80211_hwsim_new_radio 2776 2808 +32
tipc_mon_rcv 1032 1058 +26
svcauth_gss_legacy_init 1413 1429 +16
tipc_bcbase_select_primary 379 392 +13
nfsd4_exchange_id 1247 1260 +13
nfsd4_setclientid_confirm 782 793 +11
...
put_client_renew_locked 494 480 -14
ip_set_sockfn_get 730 716 -14
geneve_sock_add 829 813 -16
nfsd4_sequence_done 721 703 -18
nlmclnt_lookup_host 708 686 -22
nfsd4_lockt 1085 1063 -22
nfs_get_client 1077 1050 -27
tcf_bpf_init 1106 1076 -30
nfsd4_encode_fattr 5997 5930 -67
Total: Before=154856051, After=154854321, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add utility functions to convert a 32 bits key into a 64 bits tunnel and
vice versa.
These functions will be used instead of cloning code in GRE and VXLAN,
and in tc act_iptunnel which will be introduced in a following patch in
this patchset.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the inner_protocol is set on transmit so that GSO segmentation,
which relies on that field, works correctly.
This is achieved by setting the inner_protocol in gre_build_header rather
than each caller of that function. It ensures that the inner_protocol is
set when gre_fb_xmit() is used to transmit GRE which was not previously the
case.
I have observed this is not the case when OvS transmits GRE using
lwtunnel metadata (which it always does).
Fixes: 3872035241 ("gre: Use inner_proto to obtain inner header protocol")
Cc: Pravin Shelar <pshelar@ovn.org>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an ICMPv4 message containing extensions as
defined in RFC 4884, and translating it to ICMPv6 at SIT
or GRE tunnel, we need some extra manipulation in order
to properly forward the extensions.
This patch only takes care of Time Exceeded messages as they
are the ones that typically carry information from various
routers in a fabric during a traceroute session.
It also avoids complex skb logic if the data_len is not
a multiple of 8.
RFC states :
The "original datagram" field MUST contain at least 128 octets.
If the original datagram did not contain 128 octets, the
"original datagram" field MUST be zero padded to 128 octets.
In practice routers use 128 bytes of original datagram, not more.
Initial translation was added in commit ca15a078bd
("sit: generate icmpv6 error when receiving icmpv4 error")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipgre_err() can call ip6_err_gen_icmpv6_unreach() for proper
support of ipv4+gre+icmp+ipv6+... frames, used for example
by traceroute/mtr.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) gre_parse_header() can be called from gre_err()
At this point transport header points to ICMP header, not the inner
header.
2) We can not really change transport header as ipgre_err() will later
assume transport header still points to ICMP header (using icmp_hdr())
3) pskb_may_pull() logic in gre_parse_header() really works
if we are interested at zone pointed by skb->data
4) As Jiri explained in commit b7f8fe251e ("gre: do not pull header in
ICMP error processing") we should not pull headers in error handler.
So this fix :
A) changes gre_parse_header() to use skb->data instead of
skb_transport_header()
B) Adds a nhs parameter to gre_parse_header() so that we can skip the
not pulled IP header from error path.
This offset is 0 for normal receive path.
C) remove obsolete IPV6 includes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the presence of firewalls which improperly block ICMP Unreachable
(including Fragmentation Required) messages, Path MTU Discovery is
prevented from working.
A workaround is to handle IPv4 payloads opaquely, ignoring the DF bit--as
is done for other payloads like AppleTalk--and doing transparent
fragmentation and reassembly.
Redux includes the enforcement of mutual exclusion between this feature
and Path MTU Discovery as suggested by Alexander Duyck.
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function gretap_fb_dev_create() (only used by ovs) never calls
rtnl_configure_link(). The consequence is that dev->rtnl_link_state is
never set to RTNL_LINK_INITIALIZED.
During the deletion phase, the function rollback_registered_many() sends
a RTM_DELLINK only if dev->rtnl_link_state is set to RTNL_LINK_INITIALIZED.
Fixes: b2acd1dc39 ("openvswitch: Use regular GRE net_device instead of vport")
CC: Thomas Graf <tgraf@suug.ch>
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After ipgre_newlink()/geneve_configure() call, the netdev is registered.
Fixes: 7e059158d5 ("vxlan, gre, geneve: Set a large MTU on ovs-created tunnel devices")
CC: David Wragg <david@weave.works>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ipgre interface in collect metadata mode, it doesn't make sense for the
interface to be of ARPHRD_IPGRE type. The outer header of received packets
is not needed, as all the information from it is present in metadata_dst. We
already don't set ipgre_header_ops for collect metadata interfaces, which is
the only consumer of mac_header pointing to the outer IP header.
Just set the interface type to ARPHRD_NONE in collect metadata mode for
ipgre (not gretap, that still correctly stays ARPHRD_ETHER) and reset
mac_header.
Fixes: a64b04d86d ("gre: do not assign header_ops in collect metadata mode")
Fixes: 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ipgre interfaces in collect metadata mode, receive also traffic with
encapsulated Ethernet headers. The lwtunnel users are supposed to sort this
out correctly. This allows to have mixed Ethernet + L3-only traffic on the
same lwtunnel interface. This is the same way as VXLAN-GPE behaves.
To keep backwards compatibility and prevent any surprises, gretap interfaces
have priority in receiving packets with Ethernet headers.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow to make the pull dependent on the tunnel type.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's easier for gre_parse_header to return the header length instead of
filing it into a parameter. That way, the callers that don't care about the
header length can just check whether the returned value is lower than zero.
In gre_err, the tunnel header must not be pulled. See commit b7f8fe251e
("gre: do not pull header in ICMP error processing") for details.
This patch reduces the conflict between the mentioned commit and commit
95f5c64c3c ("gre: Move utility functions to common headers").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Create common functions for both IPv4 and IPv6 GRE in transmit. These
are put into gre.h.
Common functions are for:
- GRE checksum calculation. Move gre_checksum to gre.h.
- Building a GRE header. Move GRE build_header and rename
gre_build_header.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several of the GRE functions defined in net/ipv4/ip_gre.c are usable
for IPv6 GRE implementation (that is they are protocol agnostic).
These include:
- GRE flag handling functions are move to gre.h
- GRE build_header is moved to gre.h and renamed gre_build_header
- parse_gre_header is moved to gre_demux.c and renamed gre_parse_header
- iptunnel_pull_header is taken out of gre_parse_header. This is now
done by caller. The header length is returned from gre_parse_header
in an int* argument.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iptunnel_pull_header expects that IP header was already pulled; with this
expectation, it pulls the tunnel header. This is not true in gre_err.
Furthermore, ipv4_update_pmtu and ipv4_redirect expect that skb->data points
to the IP header.
We cannot pull the tunnel header in this path. It's just a matter of not
calling iptunnel_pull_header - we don't need any of its effects.
Fixes: bda7bb4634 ("gre: Allow multiple protocol listener for gre protocol.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The collect metadata mode does not support GUE nor FOU. This might be
implemented later; until then, we should reject such config.
I think this is okay to be changed. It's unlikely anyone has such
configuration (as it doesn't work anyway) and we may need a way to
distinguish whether it's supported or not by the kernel later.
For backwards compatibility with iproute2, it's not possible to just check
the attribute presence (iproute2 always includes the attribute), the actual
value has to be checked, too.
Fixes: 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipgre (i.e. not gretap) + collect metadata mode, the skb was assumed to
contain Ethernet header and was encapsulated as ETH_P_TEB. This is not the
case, the interface is ARPHRD_IPGRE and the protocol to be used for
encapsulation is skb->protocol.
Fixes: 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipgre mode (i.e. not gretap) with collect metadata flag set, the tunnel
is incorrectly assumed to be mGRE in NBMA mode (see commit 6a5f44d7a0).
This is not the case, we're controlling the encapsulation addresses by
lwtunnel metadata. And anyway, assigning dev->header_ops in collect metadata
mode does not make sense.
Although it would be more user firendly to reject requests that specify
both the collect metadata flag and a remote/local IP address, this would
break current users of gretap or introduce ugly code and differences in
handling ipgre and gretap configuration. Keep the current behavior of
remote/local IP address being ignored in such case.
v3: Back to v1, added explanation paragraph.
v2: Reject configuration specifying both remote/local address and collect
metadata flag.
Fixes: 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the IP tunnel core function iptunnel_handle_offloads so
that we return an int and do not free the skb inside the function. This
actually allows us to clean up several paths in several tunnels so that we
can free the skb at one point in the path without having to have a
secondary path if we are supporting tunnel offloads.
In addition it should resolve some double-free issues I have found in the
tunnels paths as I believe it is possible for us to end up triggering such
an event in the case of fou or gue.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue I found in which we were dropping frames if we
had enabled checksums on GRE headers that were encapsulated by either FOU
or GUE. Without this patch I was barely able to get 1 Gb/s of throughput.
With this patch applied I am now at least getting around 6 Gb/s.
The issue is due to the fact that with FOU or GUE applied we do not provide
a transport offset pointing to the GRE header, nor do we offload it in
software as the GRE header is completely skipped by GSO and treated like a
VXLAN or GENEVE type header. As such we need to prevent the stack from
generating it and also prevent GRE from generating it via any interface we
create.
Fixes: c3483384ee ("gro: Allow tunnel stacking in the case of FOU/GUE")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assumptions from commit 0c1d70af92 ("net: use dst_cache for vxlan
device"), 468dfffcd7 ("geneve: add dst caching support") and 3c1cb4d260
("net/ipv4: add dst cache support for gre lwtunnels") on dst_cache usage
when ip_tunnel_info is used is unfortunately not always valid as assumed.
While it seems correct for ip_tunnel_info front-ends such as OVS, eBPF
however can fill in ip_tunnel_info for consumers like vxlan, geneve or gre
with different remote dsts, tos, etc, therefore they cannot be assumed as
packet independent.
Right now vxlan, geneve, gre would cache the dst for eBPF and every packet
would reuse the same entry that was first created on the initial route
lookup. eBPF doesn't store/cache the ip_tunnel_info, so each skb may have
a different one.
Fix it by adding a flag that checks the ip_tunnel_info. Also the !tos test
in vxlan needs to be handeled differently in this context as it is currently
inferred from ip_tunnel_info as well if present. ip_tunnel_dst_cache_usable()
helper is added for the three tunnel cases, which checks if we can use dst
cache.
Fixes: 0c1d70af92 ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd7 ("geneve: add dst caching support")
Fixes: 3c1cb4d260 ("net/ipv4: add dst cache support for gre lwtunnels")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by gre
as it modifies the skb on xmit.
Also, clean up whitespace in ipgre_tap_setup when we're already touching it.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of skb_scrub_packet was open coded in iptunnel_pull_header. Let it call
skb_scrub_packet directly instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of UDP traffic with datagram length below MTU this
gives about 4% performance increase
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users now pass false, so we can remove it, and remove the code that
was conditional upon it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
By moving stats update into iptunnel_xmit(), we can simplify
iptunnel_xmit() usage. With this change there is no need to
call another function (iptunnel_xmit_stats()) to update stats
in tunnel xmit code path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like many files are including mroute.h unnecessarily, so remove
the include. Most importantly remove it from ipv6.
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While transitioning to netdev based vport we broke OVS
feature which allows user to retrieve tunnel packet egress
information for lwtunnel devices. Following patch fixes it
by introducing ndo operation to get the tunnel egress info.
Same ndo operation can be used for lwtunnel devices and compat
ovs-tnl-vport devices. So after adding such device operation
we can remove similar operation from ovs-vport.
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently nothing preventing directing packets with IPv6
encapsulation data to IPv4 tunnels (and vice versa). If this happens,
IPv6 addresses are incorrectly interpreted as IPv4 ones.
Track whether the given ip_tunnel_key contains IPv4 or IPv6 data. Store this
in ip_tunnel_info. Reject packets at appropriate places if they are supposed
to be encapsulated into an incompatible protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mode field holds a single bit of information only (whether the
ip_tunnel_info struct is for rx or tx). Change the mode field to bit flags.
This allows more mode flags to be added.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function udp_tun_rx_dst() to initialize tunnel dst on
receive path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the lwtunnel state resides in per-protocol data. This is
a problem if we encapsulate ipv6 traffic in an ipv4 tunnel (or vice versa).
The xmit function of the tunnel does not know whether the packet has been
routed to it by ipv4 or ipv6, yet it needs the lwtstate data. Moving the
lwtstate data to dst_entry makes such inter-protocol tunneling possible.
As a bonus, this brings a nice diffstat.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the ipv4_tos and ipv4_ttl fields to just 'tos' and 'ttl', as they'll
be used with IPv6 tunnels, too.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the IPv6 addresses as an union with IPv4 ones. When using IPv4, the
newly introduced padding after the IPv4 addresses needs to be zeroed out.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for sharing GREPROTO_CISCO port was added so that
OVS gre port and kernel GRE devices can co-exist. After
flow-based tunneling patches OVS GRE protocol processing
is completely moved to ip_gre module. so there is no need
for GRE protocol hook. Following patch consolidates
GRE protocol related functions into ip_gre module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using GRE tunnel meta data collection feature, we can implement
OVS GRE vport. This patch removes all of the OVS
specific GRE code and make OVS use a ip_gre net_device.
Minimal GRE vport is kept to handle compatibility with
current userspace application.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch create new tunnel flag which enable
tunnel metadata collection on given device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 code uses a mixture of coding styles. In some instances check
for NULL pointer is done as x == NULL and sometimes as !x. !x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those are counterparts to nla_put_in_addr and nla_put_in6_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP addresses are often stored in netlink attributes. Add generic functions
to do that.
For nla_put_in_addr, it would be nicer to pass struct in_addr but this is
not used universally throughout the kernel, in way too many places __be32 is
used to store IPv4 address.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
encap.sport and encap.dport are __be16, use nla_{get,put}_be16 instead
of nla_{get,put}_u16.
Fixes the sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __be32 [addressable] [usertype] o_key
got restricted __be16 [addressable] [usertype] i_flags
warning: incorrect type in assignment (different base types)
expected restricted __be16 [usertype] sport
got unsigned short
warning: incorrect type in assignment (different base types)
expected restricted __be16 [usertype] dport
got unsigned short
warning: incorrect type in argument 3 (different base types)
expected unsigned short [unsigned] [usertype] value
got restricted __be16 [usertype] sport
warning: incorrect type in argument 3 (different base types)
expected unsigned short [unsigned] [usertype] value
got restricted __be16 [usertype] dport
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRE tap device supports Ethernet over GRE, but doesn't
care about the source address of the tunnel, therefore it
can be changed without bring device down.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NBMA GRE tunnels temporarily push GRE header that contain the
per-packet NBMA destination on the skb via header ops early in xmit
path. It is the later pulled before the real GRE header is constructed.
The inner mac was thus set differently in nbma case: the GRE header
has been pushed by neighbor layer, and mac header points to beginning
of the temporary gre header (set by dev_queue_xmit).
Now that the offloads expect mac header to point to the gre payload,
fix the xmit patch to:
- pull first the temporary gre header away
- and reset mac header to point to gre payload
This fixes tso to work again with nbma tunnels.
Fixes: 14051f0452 ("gre: Use inner mac length when computing tunnel length")
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Tom Herbert <therbert@google.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling netlink info, dport is being returned as flags. Fix
instances to return correct value.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_set_inner_protocol to set inner Ethernet protocol to
protocol being encapsulation by GRE before tunnel_xmit. This is
needed for GSO if UDP encapsulation (fou) is being done.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added netlink attrs to configure FOU encapsulation for GRE, netlink
handling of these flags, and properly adjust MTU for encapsulation.
ip_tunnel_encap is called from ip_tunnel_xmit to actually perform FOU
encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to require forcing device down on a Ethernet GRE (gretap)
tunnel to change the MAC address.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to switch the netns when packet is encapsulated or
decapsulated. In other word, the encapsulated packet is received in a netns,
where the lookup is done to find the tunnel. Once the tunnel is found, the
packet is decapsulated and injecting into the corresponding interface which
stands to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the patch, it was possible to add two times the same tunnel:
ip l a gre1 type gre remote 10.16.0.121 local 10.16.0.249
ip l a gre2 type gre remote 10.16.0.121 local 10.16.0.249
It was possible, because ip_tunnel_newlink() calls ip_tunnel_find() with the
argument dev->type, which was set only later (when calling ndo_init handler
in register_netdevice()). Let's set this type in the setup handler, which is
called before newlink handler.
Introduced by commit c544193214 ("GRE: Refactor GRE tunneling code.").
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with icmp messages, the skb->data points the
ip header that triggered the sending of the icmp message.
In gre_cisco_err(), the parse_gre_header() is called, and the
iptunnel_pull_header() is called to pull the skb at the end of
the parse_gre_header(), so the skb->data doesn't point the
inner ip header.
Unfortunately, the ipgre_err still needs those ip addresses in
inner ip header to look up tunnel by ip_tunnel_lookup().
So just use icmp_hdr() to get inner ip header instead of skb->data.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some dev_kfree_skb() with kfree_skb() calls when
we drop one skb, this might help bug tracking.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipgre_header_parse() needs to parse the tunnel's ip header and it
uses mac_header to locate the iphdr. This got broken when gre tunneling
was refactored as mac_header is no longer updated to point to iphdr.
Introduce skb_pop_mac_header() helper to do the mac_header assignment
and use it in ipgre_rcv() to fix msg_name parsing.
Bug introduced in commit c544193214 (GRE: Refactor GRE tunneling code.)
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to switch the netns when packet is encapsulated or
decapsulated. In other word, the encapsulated packet is received in a netns,
where the lookup is done to find the tunnel. Once the tunnel is found, the
packet is decapsulated and injecting into the corresponding interface which
stands to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ipgre_header() (header_ops->create) to return the correct
amount of bytes pushed. Most callers of dev_hard_header() seem
to care only if it was success, but af_packet.c uses it as
offset to the skb to copy from userspace only once. In practice
this fixes packet socket sendto()/sendmsg() to gre tunnels.
Regression introduced in c544193214
("GRE: Refactor GRE tunneling code.")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing GRE tunnel, I got:
# ip tunnel show
get tunnel gre0 failed: Invalid argument
get tunnel gre1 failed: Invalid argument
This is a regression introduced by commit c544193214
("GRE: Refactor GRE tunneling code.") because previously we
only check the parameters for SIOCADDTUNNEL and SIOCCHGTUNNEL,
after that commit, the check is moved for all commands.
So, just check for SIOCADDTUNNEL and SIOCCHGTUNNEL.
After this patch I got:
# ip tunnel show
gre0: gre/ip remote any local any ttl inherit nopmtudisc
gre1: gre/ip remote 192.168.122.101 local 192.168.122.45 ttl inherit
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is only one user is allowed to register for gre
protocol. Following patch adds de-multiplexer. So that multiple
modules can listen on gre protocol e.g. kernel gre devices and ovs.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, ip_tunnel_xmit() was using the field protocol from the IP
header passed into argument.
There is no functional change, this patch prepares the support of IPv4 over
IPv4 for module sit.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another fix needed in ipgre_err(), as parse_gre_header() might change
skb->head.
Bug added in commit c544193214 (GRE: Refactor GRE tunneling code.)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need remove erroneous semicolon, which is found by EXTRA_CFLAGS=-W,
the related commit number: c544193214
("GRE: Refactor GRE tunneling code")
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull() can change skb->head, so we must init iph/greh after
calling it.
Bug added in commit c544193214 (GRE: Refactor GRE tunneling code.)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iflink is currently set to 0 in __gre_tunnel_init(). This
function is invoked in gre_tap_init() and
ipgre_tunnel_init() which are both used to initialise the
ndo_init field of the respective net_device_ops structs
(ipgre.. and gre_tap..) used by GRE interfaces.
However, in netdevice_register() iflink is first set to -1,
then ndo_init is invoked and then iflink is assigned to a
proper value if and only if it still was -1.
Assigning 0 to iflink in ndo_init is therefore first
preventing netdev_register() to correctly assign it a proper
value and then breaking iflink at all since 0 has not
correct meaning.
Fix this by removing the iflink assignment in
__gre_tunnel_init().
Introduced by c544193214
("GRE: Refactor GRE tunneling code.")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch refactors GRE code into ip tunneling code and GRE
specific code. Common tunneling code is moved to ip_tunnel module.
ip_tunnel module is written as generic library which can be used
by different tunneling implementations.
ip_tunnel module contains following components:
- packet xmit and rcv generic code. xmit flow looks like
(gre_xmit/ipip_xmit)->ip_tunnel_xmit->ip_local_out.
- hash table of all devices.
- lookup for tunnel devices.
- control plane operations like device create, destroy, ioctl, netlink
operations code.
- registration for tunneling modules, like gre, ipip etc.
- define single pcpu_tstats dev->tstats.
- struct tnl_ptk_info added to pass parsed tunnel packet parameters.
ipip.h header is renamed to ip_tunnel.h
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 412ed94744.
The commit is wrong as tiph points to the outer IPv4 header which is
installed at ipgre_header() and not the inner one which is protocol dependant.
This commit broke succesfully opennhrp which use PF_PACKET socket with
ETH_P_NHRP protocol. Additionally ssl_addr is set to the link-layer
IPv4 address. This address is written by ipgre_header() to the skb
earlier, and this is the IPv4 header tiph should point to - regardless
of the inner protocol payload.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent patches from Pravin, most tunnels can't use iptunnel_xmit()
any more, due to ip_select_ident() and skb->ip_summed. But we can just
move these operations out of iptunnel_xmit(), so that tunnels can
use it again.
This by the way fixes a bug in vxlan (missing nf_reset()) for net-next.
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
