This reverts commit 63d0f0a695.
It caused a regression on platforms where I2C controller is synthesized
with dynamic TAR update disabled. Detection code is testing is bit
DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to
restore original value in case bit is read-write.
Instead of fixing this we revert the commit since it was preparation for
the commit 0317e6c0f1 ("i2c: designware: do not disable adapter after
transfer") which was also reverted.
Reported-by: Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Fixes: 63d0f0a695 ("i2c: designware: detect when dynamic tar update is possible")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The purpose if this ioctl is to allow a user of privcmd to restrict its
operation such that it will no longer service arbitrary hypercalls via
IOCTL_PRIVCMD_HYPERCALL, and will check for a matching domid when
servicing IOCTL_PRIVCMD_DM_OP or IOCTL_PRIVCMD_MMAP*. The aim of this
is to limit the attack surface for a compromised device model.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reported as a Kaffeine bug:
https://bugs.kde.org/show_bug.cgi?id=375811
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
On Kernel 4.9, the default is to not accept DMA on stack anymore
on x86 architecture. On other architectures, this has been a
requirement since Kernel 2.2. So, after this patch, this driver
should likely work fine on all archs.
Tested with USB ID 2040:5510: Hauppauge Windham
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Recently a new dm_op[1] hypercall was added to Xen to provide a mechanism
for restricting device emulators (such as QEMU) to a limited set of
hypervisor operations, and being able to audit those operations in the
kernel of the domain in which they run.
This patch adds IOCTL_PRIVCMD_DM_OP as gateway for __HYPERVISOR_dm_op.
NOTE: There is no requirement for user-space code to bounce data through
locked memory buffers (as with IOCTL_PRIVCMD_HYPERCALL) since
privcmd has enough information to lock the original buffers
directly.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=commit;h=524a98c2
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Multiple threads can call fanout_add() at the same time.
We need to grab fanout_mutex earlier to avoid races that could
lead to one thread freeing po->rollover that was set by another thread.
Do the same in fanout_release(), for peace of mind, and to help us
finding lockdep issues earlier.
Fixes: dc99f60069 ("packet: Add fanout support.")
Fixes: 0648ab70af ("packet: rollover prepare: per-socket state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.
It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.
Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.
Fixes: 606f399395
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a few cases we were using 'enum map_type' and that triggered this
warning when using clang:
util/session.c:1923:16: error: comparison of constant 2 with expression of type 'enum map_type' is always true
[-Werror,-Wtautological-constant-out-of-range-compare]
for (i = 0; i < MAP__NR_TYPES; ++i) {
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-i6uyo6bsopa2dghnx8qo7rri@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So set it only for other compilers, allowing us to overcome yet another
build failure due to an inexistent clang -W option:
error: unknown warning option '-Wno-override-init'; did you mean '-Wno-override-module'? [-Werror,-Wunknown-warning-option]
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-oaa1ici3j8nygp4pzl2oobh3@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As this is a GNU extension and while harmless in this case, we can do
the same thing in a more clearer way by using a existing thread_map and
cpu_map constructors:
With this we avoid this while compiling with clang:
util/evsel.c:1659:17: error: field 'map' with variable sized type 'struct cpu_map' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct cpu_map map;
^
util/evsel.c:1667:20: error: field 'map' with variable sized type 'struct thread_map' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct thread_map map;
^
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-207juvrqjiar7uvas2s83v5i@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Genuine problem detected with clang, the warnings are spot on:
util/probe-event.c:2079:7: error: variable 'map' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
if (addr) {
^~~~
util/probe-event.c:2094:6: note: uninitialized use occurs here
if (map && !is_kprobe) {
^~~
util/probe-event.c:2079:3: note: remove the 'if' if its condition is always true
if (addr) {
^~~~~~~~~~
util/probe-event.c:2075:8: error: variable 'map' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (kernel_get_symbol_address_by_name(tp->symbol,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
util/probe-event.c:2094:6: note: uninitialized use occurs here
if (map && !is_kprobe) {
^~~
util/probe-event.c:2075:4: note: remove the 'if' if its condition is always false
if (kernel_get_symbol_address_by_name(tp->symbol,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
util/probe-event.c:2064:17: note: initialize the variable 'map' to silence this warning
struct map *map;
^
= NULL
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-m3501el55i10hctfbmi2qxzr@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As this is a GNU extension and while harmless in this case, we can do
the same thing in a more clearer way by using an existing thread_map
constructor.
With this we avoid this while compiling with clang:
util/parse-events.c:2024:21: error: field 'map' with variable sized type 'struct thread_map' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct thread_map map;
^
1 error generated.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-tqocbplnyyhpst6drgm2u4m3@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As this is a GNU extension and while harmless in this case, we can do
the same thing in a more clearer way by using an existing thread_map
constructor.
With this we avoid this while compiling with clang:
builtin-record.c:659:21: error: field 'map' with variable sized type 'struct thread_map' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct thread_map map;
^
1 error generated.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-c9drclo52ezxmwa7qxklin2y@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
End result is the same, its an ABI, so the struct won't change, avoid
using a GNU extension, so that we can catch other cases that may be bugs.
Caught when building with clang:
tests/parse-no-sample-id-all.c:53:20: error: field 'attr' with variable sized type 'struct attr_event' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct attr_event attr;
^
1 error generated.
Testing it:
# perf test sample_id
24: Parse with no sample_id_all bit set : Ok
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-e2vs1x771fc208uvxnwcf08b@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When building with clang we get this error:
bench/numa.c:46:9: error: 'dprintf' macro redefined [-Werror,-Wmacro-redefined]
#define dprintf(x...) do { if (g && g->p.show_details >= 1) printf(x); } while (0)
^
/usr/include/bits/stdio2.h:145:12: note: previous definition is here
# define dprintf(fd, ...) \
^
CC /tmp/build/perf/tests/parse-no-sample-id-all.o
1 error generated.
So, make sure it is undefined before using that name.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Cc: Jakub Jelen <jjelen@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-f654o2svtrutamvxt7igwz74@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This reverts commit 60758d6668.
Now that libsubcmd makes sure that OPT_UINTEGER options will not
return negative values, we can revert this patch while addressing
the problem it solved:
# perf bench futex hash -t -4
# Running 'futex/hash' benchmark:
Error: switch `t' expects an unsigned numerical value
Usage: perf bench futex hash <options>
-t, --threads <n> Specify amount of threads
# perf bench futex hash -t-4
# Running 'futex/hash' benchmark:
Error: switch `t' expects an unsigned numerical value
Usage: perf bench futex hash <options>
-t, --threads <n> Specify amount of threads
#
IMO it is more reasonable to flat out refuse to process a negative
number than to silently turn it into an absolute value.
This also helps in silencing clang's complaint about asking for an
absolute value of an unsigned integer:
bench/futex-hash.c:133:10: error: taking the absolute value of unsigned type 'unsigned int' has no effect [-Werror,-Wabsolute-value]
nsecs = futexbench_sanitize_numeric(nsecs);
^
bench/futex.h:104:42: note: expanded from macro 'futexbench_sanitize_numeric'
#define futexbench_sanitize_numeric(__n) abs((__n))
^
bench/futex-hash.c:133:10: note: remove the call to 'abs' since unsigned values cannot be negative
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-2kl68v22or31vw643m2exz8x@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Options marked OPTION_UINTEGER or OPTION_U64 clearly indicates that an
unsigned value is expected, so just error out when a negative value is
passed, instead of returning something undesired to the tool.
E.g.:
# perf bench futex hash -t -4
# Running 'futex/hash' benchmark:
Error: switch `t' expects an unsigned numerical value
Usage: perf bench futex hash <options>
-t, --threads <n> Specify amount of threads
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-2mdn8s2raatyhz7tamrsz22r@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In commit 98e3862ca2 ("kcm: fix 0-length case for kcm_sendmsg()")
I tried to avoid skb allocation for 0-length case, but missed
a check for NULL pointer in the non EOR case.
Fixes: 98e3862ca2 ("kcm: fix 0-length case for kcm_sendmsg()")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let bcm_qspi_bspi_flash_read() return all the requested bytes by breaking
up the reads for BSPI block into optimal chunks size that a BSPI block can
handle.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call that used chip was dropped in 1f0f30e404. Drop the
leftover declaration and initialization.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
I typoed "facilitate" as "faciltate" a few years back...
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Add the missing platform_driver_unregister() and remove the duplicate
platform_device_unregister(force_pdev) in the error handling case.
Fixes: 00194826e6 ("tpm_tis: Clean up the force=1 module parameter")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan T. Leighton says:
====================
IPv4-mapped on wire, :: dst address issue
Under some circumstances IPv6 datagrams are sent with IPv4-mapped IPv6
addresses as the source. Given an IPv6 socket bound to an IPv4-mapped
IPv6 address, and an IPv6 destination address, both TCP and UDP will
will send packets using the IPv4-mapped IPv6 address as the source. Per
RFC 6890 (Table 20), IPv4-mapped IPv6 source addresses are not allowed
in an IP datagram. The problem can be observed by attempting to
connect() either a TCP or UDP socket, or by using sendmsg() with a UDP
socket. The patch is intended to correct this issue for all socket
types.
linux follows the BSD convention that an IPv6 destination address
specified as in6addr_any is converted to the loopback address.
Currently, neither TCP nor UDP consider the possibility that the source
address is an IPv4-mapped IPv6 address, and assume that the appropriate
loopback address is ::1. The patch adds a check on whether or not the
source address is an IPv4-mapped IPv6 address and then sets the
destination address to either ::ffff:127.0.0.1 or ::1, as appropriate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check on the type of the source address for the case
where the destination address is in6addr_any. If the source is an
IPv4-mapped IPv6 source address, the destination is changed to
::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This
is done in three locations to handle UDP calls to either connect() or
sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays
handling an in6addr_any destination until very late, so the patch only
needs to handle the case where the source is an IPv4-mapped IPv6
address.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver supports the Lantiq SSC SPI controller in master
mode. This controller is found on Intel (former Lantiq) SoCs like
the Danube, Falcon, xRX200, xRX300.
The hardware uses two hardware FIFOs one for received and one for
transferred bytes. When the driver writes data into the transmit FIFO
the complete word is taken from the FIFO into a shift register. The
data from this shift register is then written to the wire. This driver
uses the interrupts signaling the status of the FIFOs and not the shift
register. It is also possible to use the interrupts for the shift
register, but they will send a signal after every word. When using the
interrupts for the shift register we get a signal when the last word is
written into the shift register and not when it is written to the wire.
After all FIFOs are empty the driver busy waits till the hardware is
not busy any more and returns the transfer status.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When called by HW offloading drivers, the TC action (e.g
net/sched/act_mirred.c) code uses this_cpu logic, e.g
_bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets)
per the kernel documention, preemption should be disabled, add that.
Before the fix, when running with CONFIG_PREEMPT set, we get a
BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793
asserion from the TC action (mirred) stats_update callback.
Fixes: aad7e08d39 ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a BUG when the kernel tries to mount a file system constructed as
follows:
echo foo > foo.txt
mke2fs -Fq -t ext4 -O encrypt foo.img 100
debugfs -w foo.img << EOF
write foo.txt a
set_inode_field a i_flags 0x80800
set_super_value s_last_orphan 12
quit
EOF
root@kvm-xfstests:~# mount -o loop foo.img /mnt
[ 160.238770] ------------[ cut here ]------------
[ 160.240106] kernel BUG at /usr/projects/linux/ext4/fs/ext4/inode.c:3874!
[ 160.240106] invalid opcode: 0000 [#1] SMP
[ 160.240106] Modules linked in:
[ 160.240106] CPU: 0 PID: 2547 Comm: mount Tainted: G W 4.10.0-rc3-00034-gcdd33b941b67 #227
[ 160.240106] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.1-1 04/01/2014
[ 160.240106] task: f4518000 task.stack: f47b6000
[ 160.240106] EIP: ext4_block_zero_page_range+0x1a7/0x2b4
[ 160.240106] EFLAGS: 00010246 CPU: 0
[ 160.240106] EAX: 00000001 EBX: f7be4b50 ECX: f47b7dc0 EDX: 00000007
[ 160.240106] ESI: f43b05a8 EDI: f43babec EBP: f47b7dd0 ESP: f47b7dac
[ 160.240106] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 160.240106] CR0: 80050033 CR2: bfd85b08 CR3: 34a00680 CR4: 000006f0
[ 160.240106] Call Trace:
[ 160.240106] ext4_truncate+0x1e9/0x3e5
[ 160.240106] ext4_fill_super+0x286f/0x2b1e
[ 160.240106] ? set_blocksize+0x2e/0x7e
[ 160.240106] mount_bdev+0x114/0x15f
[ 160.240106] ext4_mount+0x15/0x17
[ 160.240106] ? ext4_calculate_overhead+0x39d/0x39d
[ 160.240106] mount_fs+0x58/0x115
[ 160.240106] vfs_kern_mount+0x4b/0xae
[ 160.240106] do_mount+0x671/0x8c3
[ 160.240106] ? _copy_from_user+0x70/0x83
[ 160.240106] ? strndup_user+0x31/0x46
[ 160.240106] SyS_mount+0x57/0x7b
[ 160.240106] do_int80_syscall_32+0x4f/0x61
[ 160.240106] entry_INT80_32+0x2f/0x2f
[ 160.240106] EIP: 0xb76b919e
[ 160.240106] EFLAGS: 00000246 CPU: 0
[ 160.240106] EAX: ffffffda EBX: 08053838 ECX: 08052188 EDX: 080537e8
[ 160.240106] ESI: c0ed0000 EDI: 00000000 EBP: 080537e8 ESP: bfa13660
[ 160.240106] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b
[ 160.240106] Code: 59 8b 00 a8 01 0f 84 09 01 00 00 8b 07 66 25 00 f0 66 3d 00 80 75 61 89 f8 e8 3e e2 ff ff 84 c0 74 56 83 bf 48 02 00 00 00 75 02 <0f> 0b 81 7d e8 00 10 00 00 74 02 0f 0b 8b 43 04 8b 53 08 31 c9
[ 160.240106] EIP: ext4_block_zero_page_range+0x1a7/0x2b4 SS:ESP: 0068:f47b7dac
[ 160.317241] ---[ end trace d6a773a375c810a5 ]---
The problem is that when the kernel tries to truncate an inode in
ext4_truncate(), it tries to clear any on-disk data beyond i_size.
Without the encryption key, it can't do that, and so it triggers a
BUG.
E2fsck does *not* provide this service, and in practice most file
systems have their orphan list processed by e2fsck, so to avoid
crashing, this patch skips this step if we don't have access to the
encryption key (which is the case when processing the orphan list; in
all other cases, we will have the encryption key, or the kernel
wouldn't have allowed the file to be opened).
An open question is whether the fact that e2fsck isn't clearing the
bytes beyond i_size causing problems --- and if we've lived with it
not doing it for so long, can we drop this from the kernel replay of
the orphan list in all cases (not just when we don't have the key for
encrypted inodes).
Addresses-Google-Bug: #35209576
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Since function tables are a common target for attackers, it's best to keep
them in read-only memory. As such, this makes the CDROM device ops tables
const. This drops additionally n_minors, since it isn't used meaningfully,
and sets the only user of cdrom_dummy_generic_packet explicitly so the
variables can all be const.
Inspired by similar changes in grsecurity/PaX.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jens Axboe <axboe@fb.com>
The old elevator= boot parameter blindly attempts to load the
same scheduler for mq and !mq devices, leading to a crash if
we specify the wrong one.
Ensure that we only apply this boot parameter to old !mq devices.
Signed-off-by: Jens Axboe <axboe@fb.com>
Declare device_type structure as const as it is only stored in the
type field of a device structure. This field is of type const, so add
const to the declaration of device_type structure.
File size before: drivers/hid/intel-ish-hid/ishtp/bus.o
text data bss dec hex filename
4260 336 16 4612 1204 hid/intel-ish-hid/ishtp/bus.o
File size after: drivers/hid/intel-ish-hid/ishtp/bus.o
text data bss dec hex filename
4324 272 16 4612 1204 hid/intel-ish-hid/ishtp/bus.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-----BEGIN PGP SIGNATURE-----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=OTHY
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A colorspace regression fix in V4L2 core and a CEC core bug that makes
it discard valid messages"
* tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] cec: initiator should be the same as the destination for, poll
[media] videodev2.h: go back to limited range Y'CbCr for SRGB and, ADOBERGB
The prox/range bits included in the Bluetooth reports from the Intuos Pro
were being ignored, leading to two issues. Firstly, the pen would never
announce a BTN_TOOL_PEN event with value 0, leaving userspace to believe
the pen was always active. Secondly, the driver would continue to send
events for data while the packet's "prox" bit was clear. This can lead
to sudden incorrect pointer jumps if the pen is slowly moved away from
the tablet surface.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To avoid this when using clang:
warning: optimization level '-O6' is not supported; using '-O3' instead
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-kaghp8ddvzdsg03putemcq96@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To allow building with clang, avoiding:
error: unknown warning option '-Wstrict-aliasing=3'; did you mean '-Wstring-plus-int'? [-Werror,-Wunknown-warning-option]
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-xvthlvmhzfnt7jx73jgmaea1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Last time we did that was when we enabled Bulldozer. Now, we enabled Zen
so it is only natural ... :-)
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Yazen Ghannam <Yazen.Ghannam@amd.com>
Add a new command cpp_its_S introduced in commit cf2a5e0bb4 ("MIPS:
Support generating Flattened Image Trees (.itb)") to ksym_dep_filter
handler - otherwise a warning is produced during the build of MIPS
platforms (when vmlinux.*.itb target is chosen).
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Michal Marek <mmarek@suse.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15278/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. In the case of
some code where it is modular, we can extend that to also include
files that are building basic support functionality but not related
to loading or registering the final module; such files also have
no need whatsoever for module.h
The advantage in removing such instances is that module.h itself
sources about 15 other headers; adding significantly to what we feed
cpp, and it can obscure what headers we are effectively using.
Since module.h might have been the implicit source for init.h
(for __init) and for export.h (for EXPORT_SYMBOL) we consider each
instance for the presence of either and replace/add as needed.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Build coverage of all the mips defconfigs revealed the module.h
header was masking a couple of implicit include instances, so
we add the appropriate headers there.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Steven J. Hill" <steven.hill@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15131/
[james.hogan@imgtec.com: Preserve sort order where it already exists]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Unify definitions for MIPS performance counter register fields in
mipsregs.h rather than duplicating them in perf_events and oprofile.
This will allow future patches to use them to expose performance
counters to KVM guests.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Robert Richter <rric@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: oprofile-list@lists.sf.net
Patchwork: https://patchwork.linux-mips.org/patch/15212/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Disable stack checking on MIPS kernels. Some distribution toolchains
might pass the -fstack-check option to gcc. This results in a
store-doubleword instruction being emitted at the top of all
functions that checks the available stack space. E.g.,
a80000000001d740 <per_cpu_init>:
a80000000001d740: ffa0bfc0 sd zero,-16448(sp)
a80000000001d744: 2405ffc9 li a1,-55
a80000000001d748: 67bdffc0 daddiu sp,sp,-64
Generally, this is undesirable, and especially on the SGI IP27
platform, it will trigger a NULL pointer dereference in
'_raw_spin_lock_irq' during early init.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Suggested-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15132/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Add all the necessary platform code to initialize the dwc3
USB host controller. This code initializes the clocks and
performs a reset on the USB core and PHYs. The driver code
in 'drivers/usb/dwc3' is where the real driver lives.
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15108/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
The build of tilegx allmodconfig fails with:
../arch/tile/include/asm/div64.h:5:15: error: unknown type name 'u64'
static inline u64 mul_u32_u32(u32 a, u32 b)
^~~
../arch/tile/include/asm/div64.h:5:31: error: unknown type name 'u32'
static inline u64 mul_u32_u32(u32 a, u32 b)
^~~
../arch/tile/include/asm/div64.h:5:38: error: unknown type name 'u32'
static inline u64 mul_u32_u32(u32 a, u32 b)
^~~
In file included from ../fs/ubifs/ubifs.h:26:0,
from ../fs/ubifs/shrinker.c:42:
../include/linux/math64.h: In function 'mul_u64_u32_shr':
../arch/tile/include/asm/div64.h:9:21: error: implicit declaration of
function 'mul_u32_u32' [-Werror=implicit-function-declaration]
Include the linux/types.h in tiles div64.h to slve the problem.
Fixes: 9e3d6223d2 ("math64, timers: Fix 32bit mul_u64_u32_shr() and friends")
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: http://lkml.kernel.org/r/1485275961-20112-1-git-send-email-sudip.mukherjee@codethink.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Adding dedicated flag for AUTO_BKOPS in card->ext_csd structure.
Read AUTO_BKOPS bit value from the device EXT_CSD and set to the
card->ext_csd structure.
In mmc_decode_ext_csd() add a print message in case the AUTO_BKOPS
is enabled
Signed-off-by: Uri Yanai <uri.yanai@sandisk.com>
Signed-off-by: Alex Lemberg <alex.lemberg@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Inverse the logic for printing the debug message.
In mmc_decode_ext_csd() print message when MAN_BKOPS_EN is set
Signed-off-by: Uri Yanai <uri.yanai@sandisk.com>
Signed-off-by: Alex Lemberg <alex.lemberg@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for HS400 mode.
The driver still misses support for tuning, therefore
highspeed modes like HS400 might not work under all
circumstances yet.
Successfully tested on a Odroid C2 (S905 GXBB).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
